@@ -398,7 +398,6 @@ config SATA_DWC_VDEBUG
config SATA_HIGHBANK
tristate "Calxeda Highbank SATA support"
- depends on HAS_DMA
depends on ARCH_HIGHBANK || COMPILE_TEST
help
This option enables support for the Calxeda Highbank SoC's
@@ -408,7 +407,6 @@ config SATA_HIGHBANK
config SATA_MV
tristate "Marvell SATA support"
- depends on HAS_DMA
depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \
ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST
select GENERIC_PHY
@@ -419,7 +419,7 @@ config CRYPTO_DEV_EXYNOS_RNG
config CRYPTO_DEV_S5P
tristate "Support for Samsung S5PV210/Exynos crypto accelerator"
depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
- depends on HAS_IOMEM && HAS_DMA
+ depends on HAS_IOMEM
select CRYPTO_AES
select CRYPTO_BLKCIPHER
help
@@ -473,7 +473,6 @@ config CRYPTO_DEV_BFIN_CRC
config CRYPTO_DEV_ATMEL_AUTHENC
tristate "Support for Atmel IPSEC/SSL hw accelerator"
- depends on HAS_DMA
depends on ARCH_AT91 || COMPILE_TEST
select CRYPTO_AUTHENC
select CRYPTO_DEV_ATMEL_AES
@@ -486,7 +485,6 @@ config CRYPTO_DEV_ATMEL_AUTHENC
config CRYPTO_DEV_ATMEL_AES
tristate "Support for Atmel AES hw accelerator"
- depends on HAS_DMA
depends on ARCH_AT91 || COMPILE_TEST
select CRYPTO_AES
select CRYPTO_AEAD
@@ -501,7 +499,6 @@ config CRYPTO_DEV_ATMEL_AES
config CRYPTO_DEV_ATMEL_TDES
tristate "Support for Atmel DES/TDES hw accelerator"
- depends on HAS_DMA
depends on ARCH_AT91 || COMPILE_TEST
select CRYPTO_DES
select CRYPTO_BLKCIPHER
@@ -515,7 +512,6 @@ config CRYPTO_DEV_ATMEL_TDES
config CRYPTO_DEV_ATMEL_SHA
tristate "Support for Atmel SHA hw accelerator"
- depends on HAS_DMA
depends on ARCH_AT91 || COMPILE_TEST
select CRYPTO_HASH
help
@@ -581,7 +577,8 @@ config CRYPTO_DEV_CAVIUM_ZIP
config CRYPTO_DEV_QCE
tristate "Qualcomm crypto engine accelerator"
- depends on (ARCH_QCOM || COMPILE_TEST) && HAS_DMA && HAS_IOMEM
+ depends on ARCH_QCOM || COMPILE_TEST
+ depends on HAS_IOMEM
select CRYPTO_AES
select CRYPTO_DES
select CRYPTO_ECB
@@ -605,7 +602,6 @@ source "drivers/crypto/vmx/Kconfig"
config CRYPTO_DEV_IMGTEC_HASH
tristate "Imagination Technologies hardware hash accelerator"
depends on MIPS || COMPILE_TEST
- depends on HAS_DMA
select CRYPTO_MD5
select CRYPTO_SHA1
select CRYPTO_SHA256
@@ -657,7 +653,6 @@ config CRYPTO_DEV_ROCKCHIP
config CRYPTO_DEV_MEDIATEK
tristate "MediaTek's EIP97 Cryptographic Engine driver"
- depends on HAS_DMA
depends on (ARM && ARCH_MEDIATEK) || COMPILE_TEST
select CRYPTO_AES
select CRYPTO_AEAD
@@ -695,7 +690,7 @@ source "drivers/crypto/stm32/Kconfig"
config CRYPTO_DEV_SAFEXCEL
tristate "Inside Secure's SafeXcel cryptographic engine driver"
- depends on HAS_DMA && OF
+ depends on OF
depends on (ARM64 && ARCH_MVEBU) || (COMPILE_TEST && 64BIT)
select CRYPTO_AES
select CRYPTO_BLKCIPHER
@@ -713,7 +708,6 @@ config CRYPTO_DEV_SAFEXCEL
config CRYPTO_DEV_ARTPEC6
tristate "Support for Axis ARTPEC-6/7 hardware crypto acceleration."
depends on ARM && (ARCH_ARTPEC || COMPILE_TEST)
- depends on HAS_DMA
depends on OF
select CRYPTO_AEAD
select CRYPTO_AES
@@ -1,5 +1,4 @@
menu "IEEE 1394 (FireWire) support"
- depends on HAS_DMA
depends on PCI || COMPILE_TEST
# firewire-core does not depend on PCI but is
# not useful without PCI controller driver
@@ -53,7 +53,6 @@ config FPGA_MGR_ALTERA_CVP
config FPGA_MGR_ZYNQ_FPGA
tristate "Xilinx Zynq FPGA"
depends on ARCH_ZYNQ || COMPILE_TEST
- depends on HAS_DMA
help
FPGA manager driver support for Xilinx Zynq FPGAs.
@@ -2,7 +2,6 @@ config IMX_IPUV3_CORE
tristate "IPUv3 core support"
depends on SOC_IMX5 || SOC_IMX6Q || ARCH_MULTIPLATFORM || COMPILE_TEST
depends on DRM || !DRM # if DRM=m, this can't be 'y'
- depends on HAS_DMA
select BITREVERSE
select GENERIC_ALLOCATOR if DRM
select GENERIC_IRQ_CHIP
@@ -723,7 +723,6 @@ config I2C_MPC
config I2C_MT65XX
tristate "MediaTek I2C adapter"
depends on ARCH_MEDIATEK || COMPILE_TEST
- depends on HAS_DMA
help
This selects the MediaTek(R) Integrated Inter Circuit bus driver
for MT65xx and MT81xx.
@@ -901,7 +900,6 @@ config I2C_SH7760
config I2C_SH_MOBILE
tristate "SuperH Mobile I2C Controller"
- depends on HAS_DMA
depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
help
If you say yes to this option, support will be included for the
@@ -1104,7 +1102,6 @@ config I2C_XLP9XX
config I2C_RCAR
tristate "Renesas R-Car I2C Controller"
- depends on HAS_DMA
depends on ARCH_RENESAS || COMPILE_TEST
select I2C_SLAVE
help
@@ -158,7 +158,6 @@ config AT91_SAMA5D2_ADC
tristate "Atmel AT91 SAMA5D2 ADC"
depends on ARCH_AT91 || COMPILE_TEST
depends on HAS_IOMEM
- depends on HAS_DMA
select IIO_TRIGGERED_BUFFER
help
Say yes here to build support for Atmel SAMA5D2 ADC which is
@@ -647,7 +646,6 @@ config SD_ADC_MODULATOR
config STM32_ADC_CORE
tristate "STMicroelectronics STM32 adc core"
depends on ARCH_STM32 || COMPILE_TEST
- depends on HAS_DMA
depends on OF
depends on REGULATOR
select IIO_BUFFER
@@ -686,7 +684,6 @@ config STM32_DFSDM_CORE
config STM32_DFSDM_ADC
tristate "STMicroelectronics STM32 dfsdm adc"
depends on (ARCH_STM32 && OF) || COMPILE_TEST
- depends on HAS_DMA
select STM32_DFSDM_CORE
select REGMAP_MMIO
select IIO_BUFFER_HW_CONSUMER
@@ -23,7 +23,7 @@ config IOMMU_IO_PGTABLE
config IOMMU_IO_PGTABLE_LPAE
bool "ARMv7/v8 Long Descriptor Format"
select IOMMU_IO_PGTABLE
- depends on HAS_DMA && (ARM || ARM64 || (COMPILE_TEST && !GENERIC_ATOMIC64))
+ depends on ARM || ARM64 || (COMPILE_TEST && !GENERIC_ATOMIC64)
help
Enable support for the ARM long descriptor pagetable format.
This allocator supports 4K/2M/1G, 16K/32M and 64K/512M page
@@ -42,7 +42,7 @@ config IOMMU_IO_PGTABLE_LPAE_SELFTEST
config IOMMU_IO_PGTABLE_ARMV7S
bool "ARMv7/v8 Short Descriptor Format"
select IOMMU_IO_PGTABLE
- depends on HAS_DMA && (ARM || ARM64 || COMPILE_TEST)
+ depends on ARM || ARM64 || COMPILE_TEST
help
Enable support for the ARM Short-descriptor pagetable format.
This supports 32-bit virtual and physical addresses mapped using
@@ -374,7 +374,6 @@ config QCOM_IOMMU
# Note: iommu drivers cannot (yet?) be built as modules
bool "Qualcomm IOMMU Support"
depends on ARCH_QCOM || (COMPILE_TEST && !GENERIC_ATOMIC64)
- depends on HAS_DMA
select IOMMU_API
select IOMMU_IO_PGTABLE_LPAE
select ARM_DMA_USE_IOMMU
@@ -4,7 +4,7 @@
menuconfig NVM
bool "Open-Channel SSD target support"
- depends on BLOCK && HAS_DMA && PCI
+ depends on BLOCK && PCI
select BLK_DEV_NVME
help
Say Y here to get to enable Open-channel SSDs.
@@ -154,7 +154,6 @@ config XGENE_SLIMPRO_MBOX
config BCM_PDC_MBOX
tristate "Broadcom FlexSparx DMA Mailbox"
depends on ARCH_BCM_IPROC || COMPILE_TEST
- depends on HAS_DMA
help
Mailbox implementation for the Broadcom FlexSparx DMA ring manager,
which provides access to various offload engines on Broadcom
@@ -164,7 +163,6 @@ config BCM_FLEXRM_MBOX
tristate "Broadcom FlexRM Mailbox"
depends on ARM64
depends on ARCH_BCM_IPROC || COMPILE_TEST
- depends on HAS_DMA
select GENERIC_MSI_IRQ_DOMAIN
default m if ARCH_BCM_IPROC
help
@@ -1,7 +1,6 @@
config VIDEO_DT3155
tristate "DT3155 frame grabber"
depends on PCI && VIDEO_DEV && VIDEO_V4L2
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
default n
---help---
@@ -1,7 +1,6 @@
config VIDEO_SOLO6X10
tristate "Bluecherry / Softlogic 6x10 capture cards (MPEG-4/H.264)"
depends on PCI && VIDEO_DEV && SND && I2C
- depends on HAS_DMA
select BITREVERSE
select FONT_SUPPORT
select FONT_8x16
@@ -1,7 +1,6 @@
config STA2X11_VIP
tristate "STA2X11 VIP Video For Linux"
depends on STA2X11
- depends on HAS_DMA
select VIDEO_ADV7180 if MEDIA_SUBDRV_AUTOSELECT
select VIDEOBUF2_DMA_CONTIG
depends on PCI && VIDEO_V4L2 && VIRT_TO_BUS
@@ -1,7 +1,6 @@
config VIDEO_TW5864
tristate "Techwell TW5864 video/audio grabber and encoder"
depends on VIDEO_DEV && PCI && VIDEO_V4L2
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
---help---
Support for boards based on Techwell TW5864 chip which provides
@@ -1,7 +1,6 @@
config VIDEO_TW686X
tristate "Intersil/Techwell TW686x video capture cards"
depends on PCI && VIDEO_DEV && VIDEO_V4L2 && SND
- depends on HAS_DMA
select VIDEOBUF2_VMALLOC
select VIDEOBUF2_DMA_CONTIG
select VIDEOBUF2_DMA_SG
@@ -36,7 +36,7 @@ source "drivers/media/platform/blackfin/Kconfig"
config VIDEO_SH_VOU
tristate "SuperH VOU video output driver"
depends on MEDIA_CAMERA_SUPPORT
- depends on VIDEO_DEV && I2C && HAS_DMA
+ depends on VIDEO_DEV && I2C
depends on ARCH_SHMOBILE || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
help
@@ -85,7 +85,7 @@ config VIDEO_MUX
config VIDEO_OMAP3
tristate "OMAP 3 Camera support"
depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API && ARCH_OMAP3
- depends on HAS_DMA && OF
+ depends on OF
depends on OMAP_IOMMU
select ARM_DMA_USE_IOMMU
select VIDEOBUF2_DMA_CONTIG
@@ -102,7 +102,7 @@ config VIDEO_OMAP3_DEBUG
config VIDEO_PXA27x
tristate "PXA27x Quick Capture Interface driver"
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on PXA27x || COMPILE_TEST
select VIDEOBUF2_DMA_SG
select SG_SPLIT
@@ -112,7 +112,7 @@ config VIDEO_PXA27x
config VIDEO_QCOM_CAMSS
tristate "Qualcomm 8x16 V4L2 Camera Subsystem driver"
- depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && HAS_DMA
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
depends on (ARCH_QCOM && IOMMU_DMA) || COMPILE_TEST
select VIDEOBUF2_DMA_SG
select V4L2_FWNODE
@@ -122,7 +122,6 @@ config VIDEO_S3C_CAMIF
depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API
depends on PM
depends on ARCH_S3C64XX || PLAT_S3C24XX || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
---help---
This is a v4l2 driver for s3c24xx and s3c64xx SoC series camera
@@ -133,7 +132,7 @@ config VIDEO_S3C_CAMIF
config VIDEO_STM32_DCMI
tristate "STM32 Digital Camera Memory Interface (DCMI) support"
- depends on VIDEO_V4L2 && OF && HAS_DMA
+ depends on VIDEO_V4L2 && OF
depends on ARCH_STM32 || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_FWNODE
@@ -155,7 +154,6 @@ config VIDEO_TI_CAL
tristate "TI CAL (Camera Adaptation Layer) driver"
depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
depends on SOC_DRA7XX || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_FWNODE
default n
@@ -183,7 +181,6 @@ if V4L_MEM2MEM_DRIVERS
config VIDEO_CODA
tristate "Chips&Media Coda multi-standard codec IP"
depends on VIDEO_DEV && VIDEO_V4L2 && (ARCH_MXC || COMPILE_TEST)
- depends on HAS_DMA
select SRAM
select VIDEOBUF2_DMA_CONTIG
select VIDEOBUF2_VMALLOC
@@ -201,7 +198,6 @@ config VIDEO_MEDIATEK_JPEG
depends on MTK_IOMMU_V1 || COMPILE_TEST
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_MEDIATEK || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
---help---
@@ -213,7 +209,7 @@ config VIDEO_MEDIATEK_JPEG
config VIDEO_MEDIATEK_VPU
tristate "Mediatek Video Processor Unit"
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_MEDIATEK || COMPILE_TEST
---help---
This driver provides downloading VPU firmware and
@@ -229,7 +225,6 @@ config VIDEO_MEDIATEK_MDP
depends on MTK_IOMMU || COMPILE_TEST
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_MEDIATEK || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
select VIDEO_MEDIATEK_VPU
@@ -244,7 +239,7 @@ config VIDEO_MEDIATEK_MDP
config VIDEO_MEDIATEK_VCODEC
tristate "Mediatek Video Codec driver"
depends on MTK_IOMMU || COMPILE_TEST
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_MEDIATEK || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
@@ -271,7 +266,6 @@ config VIDEO_SAMSUNG_S5P_G2D
tristate "Samsung S5P and EXYNOS4 G2D 2d graphics accelerator driver"
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
default n
@@ -283,7 +277,6 @@ config VIDEO_SAMSUNG_S5P_JPEG
tristate "Samsung S5P/Exynos3250/Exynos4 JPEG codec driver"
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
---help---
@@ -294,7 +287,6 @@ config VIDEO_SAMSUNG_S5P_MFC
tristate "Samsung S5P MFC Video Codec"
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
default n
help
@@ -304,7 +296,6 @@ config VIDEO_MX2_EMMAPRP
tristate "MX2 eMMa-PrP support"
depends on VIDEO_DEV && VIDEO_V4L2
depends on SOC_IMX27 || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
help
@@ -316,7 +307,6 @@ config VIDEO_SAMSUNG_EXYNOS_GSC
tristate "Samsung Exynos G-Scaler driver"
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_EXYNOS || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
help
@@ -325,7 +315,6 @@ config VIDEO_SAMSUNG_EXYNOS_GSC
config VIDEO_STI_BDISP
tristate "STMicroelectronics BDISP 2D blitter driver"
depends on VIDEO_DEV && VIDEO_V4L2
- depends on HAS_DMA
depends on ARCH_STI || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
@@ -335,7 +324,6 @@ config VIDEO_STI_BDISP
config VIDEO_STI_HVA
tristate "STMicroelectronics HVA multi-format video encoder V4L2 driver"
depends on VIDEO_DEV && VIDEO_V4L2
- depends on HAS_DMA
depends on ARCH_STI || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
@@ -362,7 +350,6 @@ config VIDEO_STI_DELTA
tristate "STMicroelectronics DELTA multi-format video decoder V4L2 driver"
depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_STI || COMPILE_TEST
- depends on HAS_DMA
help
This V4L2 driver enables DELTA multi-format video decoder
of STMicroelectronics STiH4xx SoC series allowing hardware
@@ -408,7 +395,7 @@ config VIDEO_SH_VEU
config VIDEO_RENESAS_FDP1
tristate "Renesas Fine Display Processor"
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_SHMOBILE || COMPILE_TEST
depends on (!ARCH_RENESAS && !VIDEO_RENESAS_FCP) || VIDEO_RENESAS_FCP
select VIDEOBUF2_DMA_CONTIG
@@ -422,7 +409,7 @@ config VIDEO_RENESAS_FDP1
config VIDEO_RENESAS_JPU
tristate "Renesas JPEG Processing Unit"
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_RENESAS || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
@@ -447,7 +434,7 @@ config VIDEO_RENESAS_FCP
config VIDEO_RENESAS_VSP1
tristate "Renesas VSP1 Video Processing Engine"
- depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && HAS_DMA
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
depends on (ARCH_RENESAS && OF) || COMPILE_TEST
depends on (!ARM64 && !VIDEO_RENESAS_FCP) || VIDEO_RENESAS_FCP
select VIDEOBUF2_DMA_CONTIG
@@ -460,7 +447,7 @@ config VIDEO_RENESAS_VSP1
config VIDEO_ROCKCHIP_RGA
tristate "Rockchip Raster 2d Graphic Acceleration Unit"
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on ARCH_ROCKCHIP || COMPILE_TEST
select VIDEOBUF2_DMA_SG
select V4L2_MEM2MEM_DEV
@@ -477,7 +464,6 @@ config VIDEO_TI_VPE
tristate "TI VPE (Video Processing Engine) driver"
depends on VIDEO_DEV && VIDEO_V4L2
depends on SOC_DRA7XX || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select V4L2_MEM2MEM_DEV
select VIDEO_TI_VPDMA
@@ -496,7 +482,7 @@ config VIDEO_TI_VPE_DEBUG
config VIDEO_QCOM_VENUS
tristate "Qualcomm Venus V4L2 encoder/decoder driver"
- depends on VIDEO_DEV && VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_DEV && VIDEO_V4L2
depends on (ARCH_QCOM && IOMMU_DMA) || COMPILE_TEST
select QCOM_MDT_LOADER if ARCH_QCOM
select QCOM_SCM if ARCH_QCOM
@@ -638,7 +624,7 @@ if SDR_PLATFORM_DRIVERS
config VIDEO_RCAR_DRIF
tristate "Renesas Digitial Radio Interface (DRIF)"
- depends on VIDEO_V4L2 && HAS_DMA
+ depends on VIDEO_V4L2
depends on ARCH_RENESAS || COMPILE_TEST
select VIDEOBUF2_VMALLOC
---help---
@@ -1,6 +1,6 @@
config VIDEO_AM437X_VPFE
tristate "TI AM437x VPFE video capture driver"
- depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && HAS_DMA
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
depends on SOC_AM43XX || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_FWNODE
@@ -1,6 +1,6 @@
config VIDEO_ATMEL_ISC
tristate "ATMEL Image Sensor Controller (ISC) support"
- depends on VIDEO_V4L2 && COMMON_CLK && VIDEO_V4L2_SUBDEV_API && HAS_DMA
+ depends on VIDEO_V4L2 && COMMON_CLK && VIDEO_V4L2_SUBDEV_API
depends on ARCH_AT91 || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select REGMAP_MMIO
@@ -11,7 +11,7 @@ config VIDEO_ATMEL_ISC
config VIDEO_ATMEL_ISI
tristate "ATMEL Image Sensor Interface (ISI) support"
- depends on VIDEO_V4L2 && OF && HAS_DMA
+ depends on VIDEO_V4L2 && OF
depends on ARCH_AT91 || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_FWNODE
@@ -1,7 +1,6 @@
config VIDEO_BLACKFIN_CAPTURE
tristate "Blackfin Video Capture Driver"
depends on VIDEO_V4L2 && BLACKFIN && I2C
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
help
V4L2 bridge driver for Blackfin video capture device.
@@ -2,7 +2,6 @@ config VIDEO_DAVINCI_VPIF_DISPLAY
tristate "TI DaVinci VPIF V4L2-Display driver"
depends on VIDEO_V4L2
depends on ARCH_DAVINCI || COMPILE_TEST
- depends on HAS_DMA
depends on I2C
select VIDEOBUF2_DMA_CONTIG
select VIDEO_ADV7343 if MEDIA_SUBDRV_AUTOSELECT
@@ -19,7 +18,6 @@ config VIDEO_DAVINCI_VPIF_CAPTURE
tristate "TI DaVinci VPIF video capture driver"
depends on VIDEO_V4L2
depends on ARCH_DAVINCI || COMPILE_TEST
- depends on HAS_DMA
depends on I2C
select VIDEOBUF2_DMA_CONTIG
select V4L2_FWNODE
@@ -35,7 +33,6 @@ config VIDEO_DM6446_CCDC
tristate "TI DM6446 CCDC video capture driver"
depends on VIDEO_V4L2
depends on ARCH_DAVINCI || COMPILE_TEST
- depends on HAS_DMA
depends on I2C
select VIDEOBUF_DMA_CONTIG
help
@@ -52,7 +49,6 @@ config VIDEO_DM355_CCDC
tristate "TI DM355 CCDC video capture driver"
depends on VIDEO_V4L2
depends on ARCH_DAVINCI || COMPILE_TEST
- depends on HAS_DMA
depends on I2C
select VIDEOBUF_DMA_CONTIG
help
@@ -68,7 +64,6 @@ config VIDEO_DM355_CCDC
config VIDEO_DM365_ISIF
tristate "TI DM365 ISIF video capture driver"
depends on VIDEO_V4L2 && ARCH_DAVINCI
- depends on HAS_DMA
depends on I2C
select VIDEOBUF_DMA_CONTIG
help
@@ -82,7 +77,6 @@ config VIDEO_DM365_ISIF
config VIDEO_DAVINCI_VPBE_DISPLAY
tristate "TI DaVinci VPBE V4L2-Display driver"
depends on VIDEO_V4L2 && ARCH_DAVINCI
- depends on HAS_DMA
depends on I2C
select VIDEOBUF2_DMA_CONTIG
help
@@ -1,7 +1,6 @@
config VIDEO_CAFE_CCIC
tristate "Marvell 88ALP01 (Cafe) CMOS Camera Controller support"
depends on PCI && I2C && VIDEO_V4L2
- depends on HAS_DMA
select VIDEO_OV7670
select VIDEOBUF2_VMALLOC
select VIDEOBUF2_DMA_CONTIG
@@ -14,7 +13,7 @@ config VIDEO_CAFE_CCIC
config VIDEO_MMP_CAMERA
tristate "Marvell Armada 610 integrated camera controller support"
depends on ARCH_MMP && I2C && VIDEO_V4L2
- depends on HAS_DMA && BROKEN
+ depends on BROKEN
select VIDEO_OV7670
select I2C_GPIO
select VIDEOBUF2_DMA_SG
@@ -1,6 +1,6 @@
config VIDEO_RCAR_VIN
tristate "R-Car Video Input (VIN) Driver"
- depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF && HAS_DMA && MEDIA_CONTROLLER
+ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF && MEDIA_CONTROLLER
depends on ARCH_RENESAS || COMPILE_TEST
select VIDEOBUF2_DMA_CONTIG
select V4L2_FWNODE
@@ -18,9 +18,8 @@ config SOC_CAMERA_PLATFORM
config VIDEO_SH_MOBILE_CEU
tristate "SuperH Mobile CEU Interface driver"
- depends on VIDEO_DEV && SOC_CAMERA && HAS_DMA && HAVE_CLK
+ depends on VIDEO_DEV && SOC_CAMERA && HAVE_CLK
depends on ARCH_SHMOBILE || COMPILE_TEST
- depends on HAS_DMA
select VIDEOBUF2_DMA_CONTIG
select SOC_CAMERA_SCALE_CROP
---help---
@@ -1,6 +1,6 @@
config DVB_C8SECTPFE
tristate "STMicroelectronics C8SECTPFE DVB support"
- depends on PINCTRL && DVB_CORE && I2C && HAS_DMA
+ depends on PINCTRL && DVB_CORE && I2C
depends on ARCH_STI || ARCH_MULTIPLATFORM || COMPILE_TEST
select FW_LOADER
select DEBUG_FS
@@ -358,7 +358,6 @@ config MMC_MESON_MX_SDIO
tristate "Amlogic Meson6/Meson8/Meson8b SD/MMC Host Controller support"
depends on ARCH_MESON || COMPILE_TEST
depends on COMMON_CLK
- depends on HAS_DMA
depends on OF
help
This selects support for the SD/MMC Host Controller on
@@ -401,7 +400,6 @@ config MMC_OMAP
config MMC_OMAP_HS
tristate "TI OMAP High Speed Multimedia Card Interface support"
- depends on HAS_DMA
depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST
help
This selects the TI OMAP High Speed Multimedia card Interface.
@@ -511,7 +509,6 @@ config MMC_DAVINCI
config MMC_GOLDFISH
tristate "goldfish qemu Multimedia Card Interface support"
- depends on HAS_DMA
depends on GOLDFISH || COMPILE_TEST
help
This selects the Goldfish Multimedia card Interface emulation
@@ -605,7 +602,7 @@ config MMC_SDHI
config MMC_SDHI_SYS_DMAC
tristate "DMA for SDHI SD/SDIO controllers using SYS-DMAC"
- depends on MMC_SDHI && HAS_DMA
+ depends on MMC_SDHI
default MMC_SDHI if (SUPERH || ARM)
help
This provides DMA support for SDHI SD/SDIO controllers
@@ -615,7 +612,7 @@ config MMC_SDHI_SYS_DMAC
config MMC_SDHI_INTERNAL_DMAC
tristate "DMA for SDHI SD/SDIO controllers using on-chip bus mastering"
depends on ARM64 || COMPILE_TEST
- depends on MMC_SDHI && HAS_DMA
+ depends on MMC_SDHI
default MMC_SDHI if ARM64
help
This provides DMA support for SDHI SD/SDIO controllers
@@ -688,7 +685,6 @@ config MMC_CAVIUM_THUNDERX
config MMC_DW
tristate "Synopsys DesignWare Memory Card Interface"
- depends on HAS_DMA
depends on ARC || ARM || ARM64 || MIPS || COMPILE_TEST
help
This selects support for the Synopsys DesignWare Mobile Storage IP
@@ -758,7 +754,6 @@ config MMC_DW_ZX
config MMC_SH_MMCIF
tristate "SuperH Internal MMCIF support"
- depends on HAS_DMA
depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
help
This selects the MMC Host Interface controller (MMCIF) found in various
@@ -879,7 +874,6 @@ config MMC_TOSHIBA_PCI
config MMC_BCM2835
tristate "Broadcom BCM2835 SDHOST MMC Controller support"
depends on ARCH_BCM2835 || COMPILE_TEST
- depends on HAS_DMA
help
This selects the BCM2835 SDHOST MMC controller. If you have
a BCM2835 platform with SD or MMC devices, say Y or M here.
@@ -46,7 +46,7 @@ config MTD_NAND_DENALI
config MTD_NAND_DENALI_PCI
tristate "Support Denali NAND controller on Intel Moorestown"
select MTD_NAND_DENALI
- depends on HAS_DMA && PCI
+ depends on PCI
help
Enable the driver for NAND flash on Intel Moorestown, using the
Denali NAND controller core.
@@ -184,7 +184,6 @@ config MTD_NAND_S3C2410_CLKSTOP
config MTD_NAND_TANGO
tristate "NAND Flash support for Tango chips"
depends on ARCH_TANGO || COMPILE_TEST
- depends on HAS_DMA
help
Enables the NAND Flash controller on Tango chips.
@@ -328,7 +327,7 @@ config MTD_NAND_MARVELL
tristate "NAND controller support on Marvell boards"
depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
COMPILE_TEST
- depends on HAS_IOMEM && HAS_DMA
+ depends on HAS_IOMEM
help
This enables the NAND flash controller driver for Marvell boards,
including:
@@ -490,7 +489,6 @@ config MTD_NAND_SH_FLCTL
tristate "Support for NAND on Renesas SuperH FLCTL"
depends on SUPERH || COMPILE_TEST
depends on HAS_IOMEM
- depends on HAS_DMA
help
Several Renesas SuperH CPU has FLCTL. This option enables support
for NAND Flash using FLCTL.
@@ -558,7 +556,6 @@ config MTD_NAND_SUNXI
config MTD_NAND_HISI504
tristate "Support for NAND controller on Hisilicon SoC Hip04"
depends on ARCH_HISI || COMPILE_TEST
- depends on HAS_DMA
help
Enables support for NAND controller on Hisilicon SoC Hip04.
@@ -572,7 +569,6 @@ config MTD_NAND_QCOM
config MTD_NAND_MTK
tristate "Support for NAND controller on MTK SoCs"
depends on ARCH_MEDIATEK || COMPILE_TEST
- depends on HAS_DMA
help
Enables support for NAND controller on MTK SoCs.
This controller is found on mt27xx, mt81xx, mt65xx SoCs.
@@ -71,7 +71,7 @@ config SPI_FSL_QUADSPI
config SPI_HISI_SFC
tristate "Hisilicon SPI-NOR Flash Controller(SFC)"
depends on ARCH_HISI || COMPILE_TEST
- depends on HAS_IOMEM && HAS_DMA
+ depends on HAS_IOMEM
help
This enables support for hisilicon SPI-NOR flash controller.
@@ -173,7 +173,7 @@ config SUNLANCE
config AMD_XGBE
tristate "AMD 10GbE Ethernet driver"
- depends on ((OF_NET && OF_ADDRESS) || ACPI || PCI) && HAS_IOMEM && HAS_DMA
+ depends on ((OF_NET && OF_ADDRESS) || ACPI || PCI) && HAS_IOMEM
depends on X86 || ARM64 || COMPILE_TEST
select BITREVERSE
select CRC32
@@ -1,6 +1,5 @@
config NET_XGENE_V2
tristate "APM X-Gene SoC Ethernet-v2 Driver"
- depends on HAS_DMA
depends on ARCH_XGENE || COMPILE_TEST
help
This is the Ethernet driver for the on-chip ethernet interface
@@ -1,6 +1,5 @@
config NET_XGENE
tristate "APM X-Gene SoC Ethernet Driver"
- depends on HAS_DMA
depends on ARCH_XGENE || COMPILE_TEST
select PHYLIB
select MDIO_XGENE
@@ -24,7 +24,8 @@ config ARC_EMAC_CORE
config ARC_EMAC
tristate "ARC EMAC support"
select ARC_EMAC_CORE
- depends on OF_IRQ && OF_NET && HAS_DMA && (ARC || COMPILE_TEST)
+ depends on OF_IRQ && OF_NET
+ depends on ARC || COMPILE_TEST
---help---
On some legacy ARC (Synopsys) FPGA boards such as ARCAngel4/ML50x
non-standard on-chip ethernet device ARC EMAC 10/100 is used.
@@ -33,7 +34,8 @@ config ARC_EMAC
config EMAC_ROCKCHIP
tristate "Rockchip EMAC support"
select ARC_EMAC_CORE
- depends on OF_IRQ && OF_NET && REGULATOR && HAS_DMA && (ARCH_ROCKCHIP || COMPILE_TEST)
+ depends on OF_IRQ && OF_NET && REGULATOR
+ depends on ARCH_ROCKCHIP || COMPILE_TEST
---help---
Support for Rockchip RK3036/RK3066/RK3188 EMAC ethernet controllers.
This selects Rockchip SoC glue layer support for the
@@ -157,7 +157,6 @@ config BGMAC
config BGMAC_BCMA
tristate "Broadcom iProc GBit BCMA support"
depends on BCMA && BCMA_HOST_SOC
- depends on HAS_DMA
depends on BCM47XX || ARCH_BCM_5301X || COMPILE_TEST
select BGMAC
select PHYLIB
@@ -170,7 +169,6 @@ config BGMAC_BCMA
config BGMAC_PLATFORM
tristate "Broadcom iProc GBit platform support"
- depends on HAS_DMA
depends on ARCH_BCM_IPROC || COMPILE_TEST
depends on OF
select BGMAC
@@ -1,6 +1,6 @@
config NET_CALXEDA_XGMAC
tristate "Calxeda 1G/10G XGMAC Ethernet driver"
- depends on HAS_IOMEM && HAS_DMA
+ depends on HAS_IOMEM
depends on ARCH_HIGHBANK || COMPILE_TEST
select CRC32
help
@@ -5,7 +5,7 @@
config NET_VENDOR_HISILICON
bool "Hisilicon devices"
default y
- depends on (OF || ACPI) && HAS_DMA
+ depends on OF || ACPI
depends on ARM || ARM64 || COMPILE_TEST
---help---
If you have a network (Ethernet) card belonging to this class, say Y.
@@ -18,8 +18,8 @@ if NET_VENDOR_MARVELL
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
- depends on (MV64X60 || PPC32 || PLAT_ORION || COMPILE_TEST) && INET
- depends on HAS_DMA
+ depends on MV64X60 || PPC32 || PLAT_ORION || COMPILE_TEST
+ depends on INET
select PHYLIB
select MVMDIO
---help---
@@ -58,7 +58,6 @@ config MVNETA_BM_ENABLE
config MVNETA
tristate "Marvell Armada 370/38x/XP/37xx network interface support"
depends on ARCH_MVEBU || COMPILE_TEST
- depends on HAS_DMA
select MVMDIO
select PHYLINK
---help---
@@ -84,7 +83,6 @@ config MVNETA_BM
config MVPP2
tristate "Marvell Armada 375/7K/8K network interface support"
depends on ARCH_MVEBU || COMPILE_TEST
- depends on HAS_DMA
select MVMDIO
---help---
This driver supports the network interface units in the
@@ -92,7 +90,7 @@ config MVPP2
config PXA168_ETH
tristate "Marvell pxa168 ethernet support"
- depends on HAS_IOMEM && HAS_DMA
+ depends on HAS_IOMEM
depends on CPU_PXA168 || ARCH_BERLIN || COMPILE_TEST
select PHYLIB
---help---
@@ -30,7 +30,7 @@ config MLXSW_CORE_THERMAL
config MLXSW_PCI
tristate "PCI bus implementation for Mellanox Technologies Switch ASICs"
- depends on PCI && HAS_DMA && HAS_IOMEM && MLXSW_CORE
+ depends on PCI && HAS_IOMEM && MLXSW_CORE
default m
---help---
This is PCI bus implementation for Mellanox Technologies Switch ASICs.
@@ -17,7 +17,6 @@ if NET_VENDOR_RENESAS
config SH_ETH
tristate "Renesas SuperH Ethernet support"
- depends on HAS_DMA
depends on ARCH_RENESAS || SUPERH || COMPILE_TEST
select CRC32
select MII
@@ -31,7 +30,6 @@ config SH_ETH
config RAVB
tristate "Renesas Ethernet AVB support"
- depends on HAS_DMA
depends on ARCH_RENESAS || COMPILE_TEST
select CRC32
select MII
@@ -14,7 +14,7 @@ if NET_VENDOR_SOCIONEXT
config SNI_AVE
tristate "Socionext AVE ethernet support"
depends on ARCH_UNIPHIER || COMPILE_TEST
- depends on OF && HAS_DMA
+ depends on OF
select PHYLIB
---help---
Driver for gigabit ethernet MACs, called AVE, in the
@@ -23,7 +23,7 @@ config SNI_AVE
config SNI_NETSEC
tristate "Socionext NETSEC ethernet support"
depends on ARCH_SYNQUACER || COMPILE_TEST
- depends on OF && HAS_DMA
+ depends on OF
select PHYLIB
select MII
---help---
@@ -60,7 +60,6 @@ config BRCMFMAC_PCIE
bool "PCIE bus interface support for FullMAC driver"
depends on BRCMFMAC
depends on PCI
- depends on HAS_DMA
select BRCMFMAC_PROTO_MSGBUF
select FW_LOADER
---help---
@@ -7,7 +7,7 @@ config QTNFMAC
config QTNFMAC_PEARL_PCIE
tristate "Quantenna QSR10g PCIe support"
default n
- depends on HAS_DMA && PCI && CFG80211
+ depends on PCI && CFG80211
select QTNFMAC
select FW_LOADER
select CRC32
@@ -23,7 +23,6 @@ config IMX_REMOTEPROC
config OMAP_REMOTEPROC
tristate "OMAP remoteproc support"
- depends on HAS_DMA
depends on ARCH_OMAP4 || SOC_OMAP5
depends on OMAP_IOMMU
select MAILBOX
@@ -1,6 +1,6 @@
config SCSI_HISI_SAS
tristate "HiSilicon SAS"
- depends on HAS_DMA && HAS_IOMEM
+ depends on HAS_IOMEM
depends on ARM64 || COMPILE_TEST
select SCSI_SAS_LIBSAS
select BLK_DEV_INTEGRITY
@@ -71,7 +71,6 @@ config SPI_ARMADA_3700
config SPI_ATMEL
tristate "Atmel SPI Controller"
- depends on HAS_DMA
depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
help
This selects a driver for the Atmel SPI Controller, present on
@@ -252,7 +251,6 @@ config SPI_EFM32
config SPI_EP93XX
tristate "Cirrus Logic EP93xx SPI controller"
- depends on HAS_DMA
depends on ARCH_EP93XX || COMPILE_TEST
help
This enables using the Cirrus EP93xx SPI controller in master
@@ -374,7 +372,6 @@ config SPI_FSL_SPI
config SPI_FSL_DSPI
tristate "Freescale DSPI controller"
select REGMAP_MMIO
- depends on HAS_DMA
depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
help
This enables support for the Freescale DSPI controller in master
@@ -456,7 +453,6 @@ config SPI_OMAP_UWIRE
config SPI_OMAP24XX
tristate "McSPI driver for OMAP"
- depends on HAS_DMA
depends on ARCH_OMAP2PLUS || COMPILE_TEST
select SG_SPLIT
help
@@ -465,7 +461,6 @@ config SPI_OMAP24XX
config SPI_TI_QSPI
tristate "DRA7xxx QSPI controller support"
- depends on HAS_DMA
depends on ARCH_OMAP2PLUS || COMPILE_TEST
help
QSPI master controller for DRA7xxx used for flash devices.
@@ -494,7 +489,6 @@ config SPI_PIC32
config SPI_PIC32_SQI
tristate "Microchip PIC32 Quad SPI driver"
depends on MACH_PIC32 || COMPILE_TEST
- depends on HAS_DMA
help
SPI driver for PIC32 Quad SPI controller.
@@ -597,7 +591,7 @@ config SPI_SC18IS602
config SPI_SH_MSIOF
tristate "SuperH MSIOF SPI controller"
- depends on HAVE_CLK && HAS_DMA
+ depends on HAVE_CLK
depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
help
SPI driver for SuperH and SH Mobile MSIOF blocks.
@@ -675,7 +669,7 @@ config SPI_MXS
config SPI_TEGRA114
tristate "NVIDIA Tegra114 SPI Controller"
depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
- depends on RESET_CONTROLLER && HAS_DMA
+ depends on RESET_CONTROLLER
help
SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
is different than the older SoCs SPI controller and also register interface
@@ -693,7 +687,7 @@ config SPI_TEGRA20_SFLASH
config SPI_TEGRA20_SLINK
tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
- depends on RESET_CONTROLLER && HAS_DMA
+ depends on RESET_CONTROLLER
help
SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
@@ -1,7 +1,6 @@
config VIDEO_DM365_VPFE
tristate "DM365 VPFE Media Controller Capture Driver"
depends on VIDEO_V4L2 && ARCH_DAVINCI_DM365 && !VIDEO_DM365_ISIF
- depends on HAS_DMA
depends on VIDEO_V4L2_SUBDEV_API
depends on VIDEO_DAVINCI_VPBE_DISPLAY
select VIDEOBUF2_DMA_CONTIG
@@ -1,7 +1,6 @@
config VIDEO_OMAP4
tristate "OMAP 4 Camera support"
depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && I2C && ARCH_OMAP4
- depends on HAS_DMA
select MFD_SYSCON
select VIDEOBUF2_DMA_CONTIG
---help---
@@ -1,6 +1,5 @@
menuconfig BCM_VIDEOCORE
tristate "Broadcom VideoCore support"
- depends on HAS_DMA
depends on OF
depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
default y
@@ -115,7 +115,6 @@ config SERIAL_SB1250_DUART_CONSOLE
config SERIAL_ATMEL
bool "AT91 on-chip serial port support"
- depends on HAS_DMA
depends on ARCH_AT91 || COMPILE_TEST
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
@@ -586,7 +585,6 @@ config BFIN_UART3_CTSRTS
config SERIAL_IMX
tristate "IMX serial port support"
- depends on HAS_DMA
depends on ARCH_MXC || COMPILE_TEST
select SERIAL_CORE
select RATIONAL
@@ -1436,7 +1434,6 @@ config SERIAL_PCH_UART_CONSOLE
config SERIAL_MXS_AUART
tristate "MXS AUART support"
- depends on HAS_DMA
depends on ARCH_MXS || MACH_ASM9260 || COMPILE_TEST
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
@@ -1656,7 +1653,6 @@ config SERIAL_SPRD_CONSOLE
config SERIAL_STM32
tristate "STMicroelectronics STM32 serial port support"
select SERIAL_CORE
- depends on HAS_DMA
depends on ARCH_STM32 || COMPILE_TEST
help
This driver is for the on-chip Serial Controller on
@@ -179,7 +179,7 @@ config USB_R8A66597
config USB_RENESAS_USBHS_UDC
tristate 'Renesas USBHS controller'
- depends on USB_RENESAS_USBHS && HAS_DMA
+ depends on USB_RENESAS_USBHS
help
Renesas USBHS is a discrete USB host and peripheral controller chip
that supports both full and high speed USB 2.0 data transfers.
@@ -192,7 +192,7 @@ config USB_RENESAS_USBHS_UDC
config USB_RENESAS_USB3
tristate 'Renesas USB3.0 Peripheral controller'
depends on ARCH_RENESAS || COMPILE_TEST
- depends on EXTCON && HAS_DMA
+ depends on EXTCON
help
Renesas USB3.0 Peripheral controller is a USB peripheral controller
that supports super, high, and full speed USB 3.0 data transfers.
@@ -2,7 +2,7 @@
config USB_MTU3
tristate "MediaTek USB3 Dual Role controller"
- depends on EXTCON && (USB || USB_GADGET) && HAS_DMA
+ depends on EXTCON && (USB || USB_GADGET)
depends on ARCH_MEDIATEK || COMPILE_TEST
select USB_XHCI_MTK if USB_SUPPORT && USB_XHCI_HCD
help
@@ -2175,7 +2175,8 @@ config FB_XILINX
config FB_GOLDFISH
tristate "Goldfish Framebuffer"
- depends on FB && HAS_DMA && (GOLDFISH || COMPILE_TEST)
+ depends on FB
+ depends on GOLDFISH || COMPILE_TEST
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
@@ -11,9 +11,8 @@ config SND_BCM2835_SOC_I2S
config SND_SOC_CYGNUS
tristate "SoC platform audio for Broadcom Cygnus chips"
depends on ARCH_BCM_CYGNUS || COMPILE_TEST
- depends on HAS_DMA
help
Say Y if you want to add support for ASoC audio on Broadcom
Cygnus chips (bcm958300, bcm958305, bcm911360)
- If you don't know what to do here, say N.
\ No newline at end of file
+ If you don't know what to do here, say N.
@@ -1,7 +1,6 @@
config SND_KIRKWOOD_SOC
tristate "SoC Audio for the Marvell Kirkwood and Dove chips"
depends on ARCH_DOVE || ARCH_MVEBU || COMPILE_TEST
- depends on HAS_DMA
help
Say Y or M if you want to add support for codecs attached to
the Kirkwood I2S interface. You will also need to select the
@@ -1,7 +1,6 @@
config SND_PXA2XX_SOC
tristate "SoC Audio for the Intel PXA2xx chip"
depends on ARCH_PXA || COMPILE_TEST
- depends on HAS_DMA
select SND_PXA2XX_LIB
help
Say Y or M if you want to add support for codecs attached to
@@ -11,7 +11,6 @@ config SND_SOC_LPASS_CPU
config SND_SOC_LPASS_PLATFORM
tristate
- depends on HAS_DMA
select REGMAP_MMIO
config SND_SOC_LPASS_IPQ806X
@@ -22,13 +21,12 @@ config SND_SOC_LPASS_IPQ806X
config SND_SOC_LPASS_APQ8016
tristate
- depends on HAS_DMA
select SND_SOC_LPASS_CPU
select SND_SOC_LPASS_PLATFORM
config SND_SOC_STORM
tristate "ASoC I2S support for Storm boards"
- depends on SND_SOC_QCOM && HAS_DMA
+ depends on SND_SOC_QCOM
select SND_SOC_LPASS_IPQ806X
select SND_SOC_MAX98357A
help
@@ -37,7 +35,7 @@ config SND_SOC_STORM
config SND_SOC_APQ8016_SBC
tristate "SoC Audio support for APQ8016 SBC platforms"
- depends on SND_SOC_QCOM && HAS_DMA
+ depends on SND_SOC_QCOM
select SND_SOC_LPASS_APQ8016
help
Support for Qualcomm Technologies LPASS audio block in
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST". In most cases this other symbol is an architecture or platform specific symbol, or PCI. Generic symbols and drivers without platform dependencies keep their dependencies on HAS_DMA, to prevent compiling subsystems or drivers that cannot work anyway. This simplifies the dependencies, and allows to improve compile-testing. Notes: - FSL_FMAN keeps its dependency on HAS_DMA, as it calls set_dma_ops(), which does not exist if HAS_DMA=n (Do we need a dummy? The use of set_dma_ops() in this driver is questionable), - SND_SOC_LPASS_IPQ806X and SND_SOC_LPASS_PLATFORM loose their dependency on HAS_DMA, as they are selected from SND_SOC_APQ8016_SBC. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> --- drivers/ata/Kconfig | 2 -- drivers/crypto/Kconfig | 14 +++------ drivers/firewire/Kconfig | 1 - drivers/fpga/Kconfig | 1 - drivers/gpu/ipu-v3/Kconfig | 1 - drivers/i2c/busses/Kconfig | 3 -- drivers/iio/adc/Kconfig | 3 -- drivers/iommu/Kconfig | 5 ++-- drivers/lightnvm/Kconfig | 2 +- drivers/mailbox/Kconfig | 2 -- drivers/media/pci/dt3155/Kconfig | 1 - drivers/media/pci/solo6x10/Kconfig | 1 - drivers/media/pci/sta2x11/Kconfig | 1 - drivers/media/pci/tw5864/Kconfig | 1 - drivers/media/pci/tw686x/Kconfig | 1 - drivers/media/platform/Kconfig | 40 ++++++++----------------- drivers/media/platform/am437x/Kconfig | 2 +- drivers/media/platform/atmel/Kconfig | 4 +-- drivers/media/platform/blackfin/Kconfig | 1 - drivers/media/platform/davinci/Kconfig | 6 ---- drivers/media/platform/marvell-ccic/Kconfig | 3 +- drivers/media/platform/rcar-vin/Kconfig | 2 +- drivers/media/platform/soc_camera/Kconfig | 3 +- drivers/media/platform/sti/c8sectpfe/Kconfig | 2 +- drivers/mmc/host/Kconfig | 10 ++----- drivers/mtd/nand/Kconfig | 8 ++--- drivers/mtd/spi-nor/Kconfig | 2 +- drivers/net/ethernet/amd/Kconfig | 2 +- drivers/net/ethernet/apm/xgene-v2/Kconfig | 1 - drivers/net/ethernet/apm/xgene/Kconfig | 1 - drivers/net/ethernet/arc/Kconfig | 6 ++-- drivers/net/ethernet/broadcom/Kconfig | 2 -- drivers/net/ethernet/calxeda/Kconfig | 2 +- drivers/net/ethernet/hisilicon/Kconfig | 2 +- drivers/net/ethernet/marvell/Kconfig | 8 ++--- drivers/net/ethernet/mellanox/mlxsw/Kconfig | 2 +- drivers/net/ethernet/renesas/Kconfig | 2 -- drivers/net/ethernet/socionext/Kconfig | 4 +-- drivers/net/wireless/broadcom/brcm80211/Kconfig | 1 - drivers/net/wireless/quantenna/qtnfmac/Kconfig | 2 +- drivers/remoteproc/Kconfig | 1 - drivers/scsi/hisi_sas/Kconfig | 2 +- drivers/spi/Kconfig | 12 ++------ drivers/staging/media/davinci_vpfe/Kconfig | 1 - drivers/staging/media/omap4iss/Kconfig | 1 - drivers/staging/vc04_services/Kconfig | 1 - drivers/tty/serial/Kconfig | 4 --- drivers/usb/gadget/udc/Kconfig | 4 +-- drivers/usb/mtu3/Kconfig | 2 +- drivers/video/fbdev/Kconfig | 3 +- sound/soc/bcm/Kconfig | 3 +- sound/soc/kirkwood/Kconfig | 1 - sound/soc/pxa/Kconfig | 1 - sound/soc/qcom/Kconfig | 6 ++-- 54 files changed, 58 insertions(+), 141 deletions(-)