@@ -167,14 +167,14 @@ static int set_userbit(struct cardinfo *card, int bit, unsigned char state)
}
/*
- * NOTE: For the power LED, use the LED_POWER_* macros since they differ
+ * NOTE: For the power LED, use the MEMCTRL_LED_POWER_* macros since they differ
*/
static void set_led(struct cardinfo *card, int shift, unsigned char state)
{
unsigned char led;
led = readb(card->csr_remap + MEMCTRLCMD_LEDCTRL);
- if (state == LED_FLIP)
+ if (state == MEMCTRL_LED_FLIP)
led ^= (1<<shift);
else {
led &= ~(0x03 << shift);
@@ -268,7 +268,7 @@ static void mm_start_io(struct cardinfo *card)
if (debug & DEBUG_LED_ON_TRANSFER)
- set_led(card, LED_REMOVE, LED_ON);
+ set_led(card, MEMCTRL_LED_REMOVE, MEMCTRL_LED_ON);
desc = &page->desc[page->headcnt];
writel(0, card->csr_remap + DMA_PCI_ADDR);
@@ -477,7 +477,7 @@ static void process_page(unsigned long data)
}
if (debug & DEBUG_LED_ON_TRANSFER)
- set_led(card, LED_REMOVE, LED_OFF);
+ set_led(card, MEMCTRL_LED_REMOVE, MEMCTRL_LED_OFF);
if (card->check_batteries) {
card->check_batteries = 0;
@@ -652,13 +652,13 @@ HW_TRACE(0x36);
static void set_fault_to_battery_status(struct cardinfo *card)
{
if (card->battery[0].good && card->battery[1].good)
- set_led(card, LED_FAULT, LED_OFF);
+ set_led(card, MEMCTRL_LED_FAULT, MEMCTRL_LED_OFF);
else if (card->battery[0].warned || card->battery[1].warned)
- set_led(card, LED_FAULT, LED_ON);
+ set_led(card, MEMCTRL_LED_FAULT, MEMCTRL_LED_ON);
else if (!card->battery[0].good && !card->battery[1].good)
- set_led(card, LED_FAULT, LED_FLASH_7_0);
+ set_led(card, MEMCTRL_LED_FAULT, MEMCTRL_LED_FLASH_7_0);
else
- set_led(card, LED_FAULT, LED_FLASH_3_5);
+ set_led(card, MEMCTRL_LED_FAULT, MEMCTRL_LED_FLASH_3_5);
}
static void init_battery_timer(void);
@@ -919,8 +919,8 @@ static int mm_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
}
/* Clear the LED's we control */
- set_led(card, LED_REMOVE, LED_OFF);
- set_led(card, LED_FAULT, LED_OFF);
+ set_led(card, MEMCTRL_LED_REMOVE, MEMCTRL_LED_OFF);
+ set_led(card, MEMCTRL_LED_FAULT, MEMCTRL_LED_OFF);
batt_status = readb(card->csr_remap + MEMCTRLSTATUS_BATTERY);
@@ -32,16 +32,16 @@
#define MEM_2_GB 0xe0
#define MEMCTRLCMD_LEDCTRL 0x08
-#define LED_REMOVE 2
-#define LED_FAULT 4
-#define LED_POWER 6
-#define LED_FLIP 255
-#define LED_OFF 0x00
-#define LED_ON 0x01
-#define LED_FLASH_3_5 0x02
-#define LED_FLASH_7_0 0x03
-#define LED_POWER_ON 0x00
-#define LED_POWER_OFF 0x01
+#define MEMCTRL_LED_REMOVE 2
+#define MEMCTRL_LED_FAULT 4
+#define MEMCTRL_LED_POWER 6
+#define MEMCTRL_LED_FLIP 255
+#define MEMCTRL_LED_OFF 0x00
+#define MEMCTRL_LED_ON 0x01
+#define MEMCTRL_LED_FLASH_3_5 0x02
+#define MEMCTRL_LED_FLASH_7_0 0x03
+#define MEMCTRL_LED_POWER_ON 0x00
+#define MEMCTRL_LED_POWER_OFF 0x01
#define USER_BIT1 0x01
#define USER_BIT2 0x02
The umem driver defines LED_* macros for MEMCTRLCMD_LEDCTRL register values. The LED_OFF and LED_ON macros conflict with the LED subsystem's LED_OFF and LED_ON enums. This renames these LED_* macros to MEMCTRL_LED_* in umem driver. Cc: Frank Steiner <fsteiner-mail1@bio.ifi.lmu.de> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Dan Murphy <dmurphy@ti.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> --- drivers/block/umem.c | 20 ++++++++++---------- drivers/block/umem.h | 20 ++++++++++---------- 2 files changed, 20 insertions(+), 20 deletions(-)