Message ID | 20171013074936.97284-3-liwei213@huawei.com (mailing list archive) |
---|---|
State | Not Applicable |
Headers | show |
On Fri, Oct 13, 2017 at 03:49:33PM +0800, Li Wei wrote: > add ufs node document for Hisilicon. > > Signed-off-by: Li Wei <liwei213@huawei.com> > --- > Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 47 ++++++++++++++++++++++ > 1 file changed, 47 insertions(+) > create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt > > diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > new file mode 100644 > index 000000000000..ee114a65143d > --- /dev/null > +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt > @@ -0,0 +1,47 @@ > +* Hisilicon Universal Flash Storage (UFS) Host Controller > + > +UFS nodes are defined to describe on-chip UFS hardware macro. > +Each UFS Host Controller should have its own node. > + > +Required properties: > +- compatible : compatible list, contains one of the following - > + "hisilicon,hi3660-ufs" for hisi ufs host controller > + present on Hi3660 chipset. > +- reg : should contain UFS register address space & UFS SYS CTRL register address, > +- interrupt-parent : interrupt device > +- interrupts : interrupt number > +- clocks : List of phandle and clock specifier pairs > +- clock-names : List of clock input name strings sorted in the same > + order as the clocks property. "clk_ref", "clk_phy" is optional > +- resets : reset node register, one reset the clk and the other reset the controller > +- reset-names : describe reset node register > + > +Optional properties for board device: > +- reset-gpio : specifies to reset devices Should be "reset-gpios". > + > +Example: > + > + ufs: ufs@ff3b0000 { > + compatible = "hisilicon,hi3660-ufs", "jedec,ufs-1.1"; > + /* 0: HCI standard */ > + /* 1: UFS SYS CTRL */ > + reg = <0x0 0xff3b0000 0x0 0x1000>, > + <0x0 0xff3b1000 0x0 0x1000>; > + interrupt-parent = <&gic>; > + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, > + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; > + clock-names = "clk_ref", "clk_phy"; > + freq-table-hz = <0 0>, <0 0>; > + /* offset: 0x84; bit: 12 */ > + /* offset: 0x84; bit: 7 */ > + resets = <&crg_rst 0x84 12>, > + <&crg_rst 0x84 7>; > + reset-names = "rst", "assert"; > + }; > + > + &ufs { > + reset-gpio = <&gpio18 1 0>; > + status = "okay"; Don't show status or the chip/board split in examples. > + }; > + > -- > 2.11.0 >
diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt new file mode 100644 index 000000000000..ee114a65143d --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt @@ -0,0 +1,47 @@ +* Hisilicon Universal Flash Storage (UFS) Host Controller + +UFS nodes are defined to describe on-chip UFS hardware macro. +Each UFS Host Controller should have its own node. + +Required properties: +- compatible : compatible list, contains one of the following - + "hisilicon,hi3660-ufs" for hisi ufs host controller + present on Hi3660 chipset. +- reg : should contain UFS register address space & UFS SYS CTRL register address, +- interrupt-parent : interrupt device +- interrupts : interrupt number +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. "clk_ref", "clk_phy" is optional +- resets : reset node register, one reset the clk and the other reset the controller +- reset-names : describe reset node register + +Optional properties for board device: +- reset-gpio : specifies to reset devices + +Example: + + ufs: ufs@ff3b0000 { + compatible = "hisilicon,hi3660-ufs", "jedec,ufs-1.1"; + /* 0: HCI standard */ + /* 1: UFS SYS CTRL */ + reg = <0x0 0xff3b0000 0x0 0x1000>, + <0x0 0xff3b1000 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; + clock-names = "clk_ref", "clk_phy"; + freq-table-hz = <0 0>, <0 0>; + /* offset: 0x84; bit: 12 */ + /* offset: 0x84; bit: 7 */ + resets = <&crg_rst 0x84 12>, + <&crg_rst 0x84 7>; + reset-names = "rst", "assert"; + }; + + &ufs { + reset-gpio = <&gpio18 1 0>; + status = "okay"; + }; +
add ufs node document for Hisilicon. Signed-off-by: Li Wei <liwei213@huawei.com> --- Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 47 ++++++++++++++++++++++ 1 file changed, 47 insertions(+) create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt