@@ -243,8 +243,6 @@ static void esp_set_all_config3(struct esp *esp, u8 val)
/* Reset the ESP chip, _not_ the SCSI bus. */
static void esp_reset_esp(struct esp *esp)
{
- u8 family_code, version;
-
/* Now reset the ESP chip */
scsi_esp_cmd(esp, ESP_CMD_RC);
scsi_esp_cmd(esp, ESP_CMD_NULL | ESP_CMD_DMA);
@@ -257,13 +255,16 @@ static void esp_reset_esp(struct esp *esp)
*/
esp->max_period = ((35 * esp->ccycle) / 1000);
if (esp->rev == FAST) {
- version = esp_read8(ESP_UID);
- family_code = (version & 0xf8) >> 3;
- if (family_code == 0x02)
+ u8 family_code = ESP_FAMILY(esp_read8(ESP_UID));
+ if (family_code == ESP_UID_F236)
esp->rev = FAS236;
- else if (family_code == 0x0a)
+ else if (family_code == ESP_UID_HME)
esp->rev = FASHME; /* Version is usually '5'. */
- else
+ else if (family_code == ESP_UID_FSC) {
+ esp->rev = FSC;
+ /* Enable Active Negation */
+ esp_write8(ESP_CONFIG4_RADE, ESP_CFG4);
+ } else
esp->rev = FAS100A;
esp->min_period = ((4 * esp->ccycle) / 1000);
} else {
@@ -308,7 +309,7 @@ static void esp_reset_esp(struct esp *esp)
case FAS236:
case PCSCSI:
- /* Fast 236, AM53c974 or HME */
+ case FSC:
esp_write8(esp->config2, ESP_CFG2);
if (esp->rev == FASHME) {
u8 cfg3 = esp->target[0].esp_config3;
@@ -2374,6 +2375,7 @@ static const char *esp_chip_names[] = {
"ESP236",
"FAS236",
"AM53C974",
+ "53CF9x-2",
"FAS100A",
"FAST",
"FASHME",
@@ -78,12 +78,14 @@
#define ESP_CONFIG3_IMS 0x80 /* ID msg chk'ng (esp/fas236) */
#define ESP_CONFIG3_OBPUSH 0x80 /* Push odd-byte to dma (hme) */
-/* ESP config register 4 read-write, found only on am53c974 chips */
-#define ESP_CONFIG4_RADE 0x04 /* Active negation */
-#define ESP_CONFIG4_RAE 0x08 /* Active negation on REQ and ACK */
-#define ESP_CONFIG4_PWD 0x20 /* Reduced power feature */
-#define ESP_CONFIG4_GE0 0x40 /* Glitch eater bit 0 */
-#define ESP_CONFIG4_GE1 0x80 /* Glitch eater bit 1 */
+/* ESP config register 4 read-write */
+#define ESP_CONFIG4_BBTE 0x01 /* Back-to-back transfers (fsc) */
+#define ESP_CONGIG4_TEST 0x02 /* Transfer counter test mode (fsc) */
+#define ESP_CONFIG4_RADE 0x04 /* Active negation (am53c974/fsc) */
+#define ESP_CONFIG4_RAE 0x08 /* Act. negation REQ/ACK (am53c974) */
+#define ESP_CONFIG4_PWD 0x20 /* Reduced power feature (am53c974) */
+#define ESP_CONFIG4_GE0 0x40 /* Glitch eater bit 0 (am53c974) */
+#define ESP_CONFIG4_GE1 0x80 /* Glitch eater bit 1 (am53c974) */
#define ESP_CONFIG_GE_12NS (0)
#define ESP_CONFIG_GE_25NS (ESP_CONFIG_GE1)
@@ -209,10 +211,15 @@
#define ESP_TEST_TS 0x04 /* Tristate test mode */
/* ESP unique ID register read-only, found on fas236+fas100a only */
+#define ESP_UID_FAM 0xf8 /* ESP family bitmask */
+
+#define ESP_FAMILY(uid) (((uid) & ESP_UID_FAM) >> 3)
+
+/* Values for the ESP family bits */
#define ESP_UID_F100A 0x00 /* ESP FAS100A */
#define ESP_UID_F236 0x02 /* ESP FAS236 */
-#define ESP_UID_REV 0x07 /* ESP revision */
-#define ESP_UID_FAM 0xf8 /* ESP family */
+#define ESP_UID_HME 0x0a /* FAS HME */
+#define ESP_UID_FSC 0x14 /* NCR/Symbios Logic 53CF9x-2 */
/* ESP fifo flags register read-only */
/* Note that the following implies a 16 byte FIFO on the ESP. */
@@ -264,6 +271,7 @@ enum esp_rev {
ESP236,
FAS236,
PCSCSI, /* AM53c974 */
+ FSC, /* NCR/Symbios Logic 53CF9x-2 */
FAS100A,
FAST,
FASHME,
The FSC (NCR53CF9x-2 / SYM53CF9x-2) has a different family code than QLogic or Emulex parts. This caused it to be detected as a FAS100A. Unforunately, this meant the configuration of the CONFIG3 register was incorrect. This causes data transfer issues with FAST-SCSI targets. The FSC also has the CONFIG4 register. It can be used to enable a feature called Active Negation which should always be enabled according to the data manual. Signed-off-by: Kars de Jong <jongk@linux-m68k.org> --- drivers/scsi/esp_scsi.c | 18 ++++++++++-------- drivers/scsi/esp_scsi.h | 24 ++++++++++++++++-------- 2 files changed, 26 insertions(+), 16 deletions(-)