diff mbox series

[V2,1/1] scsi: ufs-pci: Force a full restore after suspend-to-disk

Message ID 20211018151004.284200-2-adrian.hunter@intel.com (mailing list archive)
State Accepted
Headers show
Series scsi: ufs-pci: Force a full restore after suspend-to-disk | expand

Commit Message

Adrian Hunter Oct. 18, 2021, 3:10 p.m. UTC 
Implement the ->restore() PM operation and set the link to off, which
will force a full reset and restore.  This ensures that Host Performance
Booster is reset after suspend-to-disk.

The Host Performance Booster feature caches logical-to-physical mapping
information in the host memory.  After suspend-to-disk, such information
is not valid, so a full reset and restore is needed.

A full reset and restore is done if the SPM level is 5 or 6, but not for
other SPM levels, so this change fixes those cases.

A full reset and restore also restores base address registers, so that
code is removed.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
---
 drivers/scsi/ufs/ufshcd-pci.c | 33 ++++++++++++++++++---------------
 1 file changed, 18 insertions(+), 15 deletions(-)
diff mbox series

Patch

diff --git a/drivers/scsi/ufs/ufshcd-pci.c b/drivers/scsi/ufs/ufshcd-pci.c
index 149c1aa09103..51424557810d 100644
--- a/drivers/scsi/ufs/ufshcd-pci.c
+++ b/drivers/scsi/ufs/ufshcd-pci.c
@@ -370,20 +370,6 @@  static void ufs_intel_common_exit(struct ufs_hba *hba)
 
 static int ufs_intel_resume(struct ufs_hba *hba, enum ufs_pm_op op)
 {
-	/*
-	 * To support S4 (suspend-to-disk) with spm_lvl other than 5, the base
-	 * address registers must be restored because the restore kernel can
-	 * have used different addresses.
-	 */
-	ufshcd_writel(hba, lower_32_bits(hba->utrdl_dma_addr),
-		      REG_UTP_TRANSFER_REQ_LIST_BASE_L);
-	ufshcd_writel(hba, upper_32_bits(hba->utrdl_dma_addr),
-		      REG_UTP_TRANSFER_REQ_LIST_BASE_H);
-	ufshcd_writel(hba, lower_32_bits(hba->utmrdl_dma_addr),
-		      REG_UTP_TASK_REQ_LIST_BASE_L);
-	ufshcd_writel(hba, upper_32_bits(hba->utmrdl_dma_addr),
-		      REG_UTP_TASK_REQ_LIST_BASE_H);
-
 	if (ufshcd_is_link_hibern8(hba)) {
 		int ret = ufshcd_uic_hibern8_exit(hba);
 
@@ -463,6 +449,18 @@  static struct ufs_hba_variant_ops ufs_intel_lkf_hba_vops = {
 	.device_reset		= ufs_intel_device_reset,
 };
 
+#ifdef CONFIG_PM_SLEEP
+static int ufshcd_pci_restore(struct device *dev)
+{
+	struct ufs_hba *hba = dev_get_drvdata(dev);
+
+	/* Force a full reset and restore */
+	ufshcd_set_link_off(hba);
+
+	return ufshcd_system_resume(dev);
+}
+#endif
+
 /**
  * ufshcd_pci_shutdown - main function to put the controller in reset state
  * @pdev: pointer to PCI device handle
@@ -546,9 +544,14 @@  ufshcd_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 }
 
 static const struct dev_pm_ops ufshcd_pci_pm_ops = {
-	SET_SYSTEM_SLEEP_PM_OPS(ufshcd_system_suspend, ufshcd_system_resume)
 	SET_RUNTIME_PM_OPS(ufshcd_runtime_suspend, ufshcd_runtime_resume, NULL)
 #ifdef CONFIG_PM_SLEEP
+	.suspend	= ufshcd_system_suspend,
+	.resume		= ufshcd_system_resume,
+	.freeze		= ufshcd_system_suspend,
+	.thaw		= ufshcd_system_resume,
+	.poweroff	= ufshcd_system_suspend,
+	.restore	= ufshcd_pci_restore,
 	.prepare	= ufshcd_suspend_prepare,
 	.complete	= ufshcd_resume_complete,
 #endif