diff mbox series

[02/25] ata: libata: move NCQ related ATA_DFLAGs

Message ID 20221208105947.2399894-3-niklas.cassel@wdc.com (mailing list archive)
State Changes Requested
Headers show
Series Add Command Duration Limits support | expand

Commit Message

Niklas Cassel Dec. 8, 2022, 10:59 a.m. UTC 
ata_dev_configure() starts off by clearing all flags in ATA_DFLAG_CFG_MASK:
dev->flags &= ~ATA_DFLAG_CFG_MASK;

ata_dev_configure() then calls ata_dev_config_lba() which calls
ata_dev_config_ncq().

ata_dev_config_ncq() will set the correct ATA_DFLAGs depending on what is
actually supported.

Since these flags are set by ata_dev_configure(), they should be in
ATA_DFLAG_CFG_MASK and not in ATA_DFLAG_INIT_MASK.

ATA_DFLAG_NCQ_PRIO_ENABLED is set via sysfs, is should therefore not be in
ATA_DFLAG_CFG_MASK. It also cannot be in ATA_DFLAG_INIT_MASK, because
ata_eh_schedule_probe() calls ata_dev_init(), which will clear all flags in
ATA_DFLAG_INIT_MASK.

This means that ATA_DFLAG_NCQ_PRIO_ENABLED (the value the user sets via
sysfs) would get silently cleared if ata_eh_schedule_probe() is called.
While that should only happen in certain circumstances, it still doesn't
seem right that it can get silently cleared.

(ata_dev_config_ncq_prio() will still clear the ATA_DFLAG_NCQ_PRIO_ENABLED
flag if ATA_DFLAG_NCQ_PRIO is suddenly no longer supported after a
revalidation.)

Because of this, move ATA_DFLAG_NCQ_PRIO_ENABLED to be outside of both
ATA_DFLAG_CFG_MASK and ATA_DFLAG_INIT_MASK.

Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
---
 include/linux/libata.h | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)
diff mbox series

Patch

diff --git a/include/linux/libata.h b/include/linux/libata.h
index 7985e6e2ae0e..9bba56f6d793 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -91,22 +91,21 @@  enum {
 	ATA_DFLAG_AN		= (1 << 7), /* AN configured */
 	ATA_DFLAG_TRUSTED	= (1 << 8), /* device supports trusted send/recv */
 	ATA_DFLAG_DMADIR	= (1 << 10), /* device requires DMADIR */
-	ATA_DFLAG_CFG_MASK	= (1 << 12) - 1,
+	ATA_DFLAG_NCQ_SEND_RECV = (1 << 11), /* device supports NCQ SEND and RECV */
+	ATA_DFLAG_NCQ_PRIO	= (1 << 12), /* device supports NCQ priority */
+	ATA_DFLAG_CFG_MASK	= (1 << 13) - 1,
 
-	ATA_DFLAG_PIO		= (1 << 12), /* device limited to PIO mode */
-	ATA_DFLAG_NCQ_OFF	= (1 << 13), /* device limited to non-NCQ mode */
+	ATA_DFLAG_PIO		= (1 << 13), /* device limited to PIO mode */
+	ATA_DFLAG_NCQ_OFF	= (1 << 14), /* device limited to non-NCQ mode */
 	ATA_DFLAG_SLEEPING	= (1 << 15), /* device is sleeping */
 	ATA_DFLAG_DUBIOUS_XFER	= (1 << 16), /* data transfer not verified */
 	ATA_DFLAG_NO_UNLOAD	= (1 << 17), /* device doesn't support unload */
 	ATA_DFLAG_UNLOCK_HPA	= (1 << 18), /* unlock HPA */
-	ATA_DFLAG_NCQ_SEND_RECV = (1 << 19), /* device supports NCQ SEND and RECV */
-	ATA_DFLAG_NCQ_PRIO	= (1 << 20), /* device supports NCQ priority */
-	ATA_DFLAG_NCQ_PRIO_ENABLED = (1 << 21), /* Priority cmds sent to dev */
-	ATA_DFLAG_INIT_MASK	= (1 << 24) - 1,
+	ATA_DFLAG_INIT_MASK	= (1 << 19) - 1,
 
+	ATA_DFLAG_NCQ_PRIO_ENABLED = (1 << 19), /* Priority cmds sent to dev */
 	ATA_DFLAG_DETACH	= (1 << 24),
 	ATA_DFLAG_DETACHED	= (1 << 25),
-
 	ATA_DFLAG_DA		= (1 << 26), /* device supports Device Attention */
 	ATA_DFLAG_DEVSLP	= (1 << 27), /* device supports Device Sleep */
 	ATA_DFLAG_ACPI_DISABLED = (1 << 28), /* ACPI for the device is disabled */