| Message ID | 20230922092906.2645265-11-haowenchao2@huawei.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | scsi:scsi_debug: Add error injection for single device | expand |
On 2023-09-22 05:29, Wenchao Hao wrote: > Add new module param "allow_restart" to control if setup > scsi_device's allow_restart flag. This is used to test scsi > command finished with sense_key 0x6, asc 0x4 and ascq 0x2 > > Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Hi, Looked at this and verified that the allow_restart flag of scsi_debug devices (disks ?) is usually 0 and when the scsi_debug module is started with allow_restart=1 then the allow_restart flag does indeed change to 1. For example: # cat /sys/class/scsi_disk/1\:0\:0\:0/allow_restart 1 That ASC/ASCQ code means: "Logical unit not ready, initializing command required" according to my library. Played around with sg_start but didn't see any change in how it reacts. According to scsi_device.h that flag's description is: "issue START_UNIT in error handler" which implies it changes how the EH handler reacts. Perhaps the 3 line patch description could say a little more about how to use this new parameter... Tested-by: Douglas Gilbert <dgilbert@interlog.com> <snip>
On 2023/10/9 7:17, Douglas Gilbert wrote: > On 2023-09-22 05:29, Wenchao Hao wrote: >> Add new module param "allow_restart" to control if setup >> scsi_device's allow_restart flag. This is used to test scsi >> command finished with sense_key 0x6, asc 0x4 and ascq 0x2 >> >> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> > > Hi, > Looked at this and verified that the allow_restart flag of scsi_debug > devices (disks ?) is usually 0 and when the scsi_debug module is > started with allow_restart=1 then the allow_restart flag does indeed > change to 1. For example: > # cat /sys/class/scsi_disk/1\:0\:0\:0/allow_restart > 1 > > That ASC/ASCQ code means: "Logical unit not ready, initializing command > required" according to my library. Played around with sg_start but didn't > see any change in how it reacts. According to scsi_device.h that flag's > description is: "issue START_UNIT in error handler" which implies it > changes how the EH handler reacts. > > Perhaps the 3 line patch description could say a little more about how > to use this new parameter... Sorry I did not write in detail. As you mentioned above, this is to determine if to trigger error. I would update the commit message to following lines: Add new module param "allow_restart" to control if setup scsi_device's allow_restart flag, this flag determines if trigger EH after command finished with sense_key 0x6, asc 0x4 and ascq 0x2, EH would be triggered if allow_restart=1 in this condition. The new param can be used with error inject added in patch6 to test how commands finished with sense_key 0x6, asc 0x4 and ascq 0x2 are handled. > > Tested-by: Douglas Gilbert <dgilbert@interlog.com> > > <snip> > > > > >
diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c index ab4a6f7de1ef..52a9ddea57d3 100644 --- a/drivers/scsi/scsi_debug.c +++ b/drivers/scsi/scsi_debug.c @@ -843,6 +843,7 @@ static bool have_dif_prot; static bool write_since_sync; static bool sdebug_statistics = DEF_STATISTICS; static bool sdebug_wp; +static bool sdebug_allow_restart; /* Following enum: 0: no zbc, def; 1: host aware; 2: host managed */ static enum blk_zoned_model sdeb_zbc_model = BLK_ZONED_NONE; static char *sdeb_zbc_model_s; @@ -5469,6 +5470,9 @@ static int scsi_debug_slave_configure(struct scsi_device *sdp) sdp->no_uld_attach = 1; config_cdb_len(sdp); + if (sdebug_allow_restart) + sdp->allow_restart = 1; + devip->debugfs_entry = debugfs_create_dir(dev_name(&sdp->sdev_dev), sdebug_debugfs_root); debugfs_create_file("error", 0600, devip->debugfs_entry, sdp, @@ -6186,6 +6190,7 @@ module_param_named(zone_cap_mb, sdeb_zbc_zone_cap_mb, int, S_IRUGO); module_param_named(zone_max_open, sdeb_zbc_max_open, int, S_IRUGO); module_param_named(zone_nr_conv, sdeb_zbc_nr_conv, int, S_IRUGO); module_param_named(zone_size_mb, sdeb_zbc_zone_size_mb, int, S_IRUGO); +module_param_named(allow_restart, sdebug_allow_restart, bool, S_IRUGO | S_IWUSR); MODULE_AUTHOR("Eric Youngdale + Douglas Gilbert"); MODULE_DESCRIPTION("SCSI debug adapter driver"); @@ -6258,6 +6263,7 @@ MODULE_PARM_DESC(zone_cap_mb, "Zone capacity in MiB (def=zone size)"); MODULE_PARM_DESC(zone_max_open, "Maximum number of open zones; [0] for no limit (def=auto)"); MODULE_PARM_DESC(zone_nr_conv, "Number of conventional zones (def=1)"); MODULE_PARM_DESC(zone_size_mb, "Zone size in MiB (def=auto)"); +MODULE_PARM_DESC(allow_restart, "Set scsi_device's allow_restart flag(def=0)"); #define SDEBUG_INFO_LEN 256 static char sdebug_info[SDEBUG_INFO_LEN];
Add new module param "allow_restart" to control if setup scsi_device's allow_restart flag. This is used to test scsi command finished with sense_key 0x6, asc 0x4 and ascq 0x2 Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> --- drivers/scsi/scsi_debug.c | 6 ++++++ 1 file changed, 6 insertions(+)