@@ -1694,7 +1694,7 @@ static int twa_reset_sequence(TW_Device_Extension *tw_dev, int soft_reset)
return retval;
} /* End twa_reset_sequence() */
-/* This funciton returns unit geometry in cylinders/heads/sectors */
+/* This function returns unit geometry in cylinders/heads/sectors */
static int twa_scsi_biosparam(struct scsi_device *sdev, struct block_device *bdev, sector_t capacity, int geom[])
{
int heads, sectors, cylinders;
@@ -1403,7 +1403,7 @@ static int twl_reset_device_extension(TW_Device_Extension *tw_dev, int ioctl_res
return retval;
} /* End twl_reset_device_extension() */
-/* This funciton returns unit geometry in cylinders/heads/sectors */
+/* This function returns unit geometry in cylinders/heads/sectors */
static int twl_scsi_biosparam(struct scsi_device *sdev, struct block_device *bdev, sector_t capacity, int geom[])
{
int heads, sectors;
@@ -6472,7 +6472,7 @@ static void FPT_BusMasterInit(u32 p_port)
*
* Function: FPT_DiagEEPROM
*
- * Description: Verfiy checksum and 'Key' and initialize the EEPROM if
+ * Description: Verify checksum and 'Key' and initialize the EEPROM if
* necessary.
*
*---------------------------------------------------------------------*/
@@ -5575,7 +5575,7 @@ static int AdvInitAsc38C1600Driver(ADV_DVC_VAR *asc_dvc)
/*
* Each ASC-38C1600 function has two connectors. Only an HVD device
* can not be connected to either connector. An LVD device or SE device
- * may be connected to either connecor. If an SE device is connected,
+ * may be connected to either connector. If an SE device is connected,
* then at most Ultra speed (20 Mhz) can be used on both connectors.
*
* If an HVD device is attached, return an error.
@@ -106,7 +106,7 @@
/*
- * Output a kernel mesage at the specified level and append the
+ * Output a kernel message at the specified level and append the
* driver name and a ": " to the start of the message
*/
#define dprintkl(level, format, arg...) \
@@ -115,10 +115,10 @@
#ifdef DEBUG_MASK
/*
- * print a debug message - this is formated with KERN_DEBUG, then the
+ * print a debug message - this is formatted with KERN_DEBUG, then the
* driver name followed by a ": " and then the message is output.
* This also checks that the specified debug level is enabled before
- * outputing the message
+ * outputting the message
*/
#define dprintkdbg(type, format, arg...) \
do { \
@@ -788,7 +788,7 @@ static void waiting_process_next(struct AdapterCtlBlk *acb)
/*
* Loop over the dcb, but we start somewhere (potentially) in
- * the middle of the loop so we need to manully do this.
+ * the middle of the loop so we need to manually do this.
*/
pos = start;
do {
@@ -1027,7 +1027,7 @@ static int dc395x_queue_command_lck(struct scsi_cmnd *cmd)
/*
* Complete the command immediatey, and then return 0 to
* indicate that we have handled the command. This is usually
- * done when the commad is for things like non existent
+ * done when the command is for things like non existent
* devices.
*/
done(cmd);
@@ -1940,7 +1940,7 @@ static void data_out_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb,
DC395x_read32(acb, TRM_S1040_DMA_CXCNT));
}
/*
- * calculate all the residue data that not yet tranfered
+ * calculate all the residue data that not yet transferred
* SCSI transfer counter + left in SCSI FIFO data
*
* .....TRM_S1040_SCSI_COUNTER (24bits)
@@ -3429,7 +3429,7 @@ static void set_basic_config(struct AdapterCtlBlk *acb)
DC395x_write8(acb, TRM_S1040_SCSI_CONFIG1, 0x03); /* was 0x13: default */
/* program Host ID */
DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id);
- /* set ansynchronous transfer */
+ /* set asynchronous transfer */
DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, 0x00);
/* Turn LED control off */
wval = DC395x_read16(acb, TRM_S1040_GEN_CONTROL) & 0x7F;
@@ -3530,7 +3530,7 @@ static void request_sense(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb,
/**
* device_alloc - Allocate a new device instance. This create the
* devices instance and sets up all the data items. The adapter
- * instance is required to obtain confiuration information for this
+ * instance is required to obtain configuration information for this
* device. This does *not* add this device to the adapters device
* list.
*
This patch fixes several typos found in the comments within the driver/scsi directory. The changes are purely cosmetic and do not affect functionality. Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com> --- drivers/scsi/3w-9xxx.c | 2 +- drivers/scsi/3w-sas.c | 2 +- drivers/scsi/FlashPoint.c | 2 +- drivers/scsi/advansys.c | 2 +- drivers/scsi/dc395x.c | 16 ++++++++-------- 5 files changed, 12 insertions(+), 12 deletions(-)