@@ -647,6 +647,7 @@ config ARCH_MSM
select GENERIC_CLOCKEVENTS
select ARCH_REQUIRE_GPIOLIB
select CLKDEV_LOOKUP
+ select SMP_COMMON_PEN if SMP
help
Support for Qualcomm MSM/QSD based systems. This runs on the
apps processor of the MSM/QSD and depends on a shared memory
@@ -16,7 +16,7 @@ obj-$(CONFIG_MSM_SMD) += last_radio_log.o
obj-$(CONFIG_MSM_SCM) += scm.o scm-boot.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
-obj-$(CONFIG_SMP) += headsmp.o platsmp.o
+obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o devices-msm7x00.o
obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o board-trout-panel.o devices-msm7x00.o
deleted file mode 100644
@@ -1,40 +0,0 @@
-/*
- * linux/arch/arm/mach-realview/headsmp.S
- *
- * Copyright (c) 2003 ARM Limited
- * All Rights Reserved
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/linkage.h>
-#include <linux/init.h>
-
- __CPUINIT
-
-/*
- * MSM specific entry point for secondary CPUs. This provides
- * a "holding pen" into which all secondary cores are held until we're
- * ready for them to initialise.
- */
-ENTRY(msm_secondary_startup)
- mrc p15, 0, r0, c0, c0, 5
- and r0, r0, #15
- adr r4, 1f
- ldmia r4, {r5, r6}
- sub r4, r4, r5
- add r6, r6, r4
-pen: ldr r7, [r6]
- cmp r7, r0
- bne pen
-
- /*
- * we've been released from the holding pen: secondary_stack
- * should now contain the SVC stack for this core
- */
- b secondary_startup
-
- .align
-1: .long .
- .long pen_release
@@ -31,45 +31,18 @@
/* Mask for edge trigger PPIs except AVS_SVICINT and AVS_SVICINTSWDONE */
#define GIC_PPI_EDGE_MASK 0xFFFFD7FF
-extern void msm_secondary_startup(void);
-/*
- * control for which core is the next to come out of the secondary
- * boot "holding pen".
- */
-volatile int pen_release = -1;
-
-static DEFINE_SPINLOCK(boot_lock);
-
void __cpuinit platform_secondary_init(unsigned int cpu)
{
/* Configure edge-triggered PPIs */
writel(GIC_PPI_EDGE_MASK, MSM_QGIC_DIST_BASE + GIC_DIST_CONFIG + 4);
- /*
- * if any interrupts are already enabled for the primary
- * core (e.g. timer irq), then they will not have been enabled
- * for us: do so
- */
- gic_secondary_init(0);
-
- /*
- * let the primary processor know we're out of the
- * pen, then head off into the C entry point
- */
- pen_release = -1;
- smp_wmb();
-
- /*
- * Synchronise with the boot thread.
- */
- spin_lock(&boot_lock);
- spin_unlock(&boot_lock);
+ pen_secondary_init(cpu);
}
static __cpuinit void prepare_cold_cpu(unsigned int cpu)
{
int ret;
- ret = scm_set_boot_addr(virt_to_phys(msm_secondary_startup),
+ ret = scm_set_boot_addr(virt_to_phys(pen_secondary_startup),
SCM_FLAG_COLDBOOT_CPU1);
if (ret == 0) {
void *sc1_base_ptr;
@@ -96,47 +69,7 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
cold_boot_done = true;
}
- /*
- * set synchronisation state between this boot processor
- * and the secondary one
- */
- spin_lock(&boot_lock);
-
- /*
- * The secondary processor is waiting to be released from
- * the holding pen - release it, then wait for it to flag
- * that it has been released by resetting pen_release.
- *
- * Note that "pen_release" is the hardware CPU ID, whereas
- * "cpu" is Linux's internal ID.
- */
- pen_release = cpu;
- __cpuc_flush_dcache_area((void *)&pen_release, sizeof(pen_release));
- outer_clean_range(__pa(&pen_release), __pa(&pen_release + 1));
-
- /*
- * Send the secondary CPU a soft interrupt, thereby causing
- * the boot monitor to read the system wide flags register,
- * and branch to the address found there.
- */
- smp_cross_call(cpumask_of(cpu), 1);
-
- timeout = jiffies + (1 * HZ);
- while (time_before(jiffies, timeout)) {
- smp_rmb();
- if (pen_release == -1)
- break;
-
- udelay(10);
- }
-
- /*
- * now the secondary core is starting up let it run its
- * calibrations, then wait for it to finish
- */
- spin_unlock(&boot_lock);
-
- return pen_release != -1 ? -ENOSYS : 0;
+ return pen_boot_secondary(cpu, idle);
}
/*