diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index bc8e2f60fe505ee2..e256c6b664710099 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -129,15 +129,6 @@ config ARCH_R8A7779
 
 comment "Renesas ARM SoCs Board Type"
 
-config MACH_ARMADILLO800EVA
-	bool "Armadillo-800 EVA board"
-	depends on ARCH_R8A7740
-	select ARCH_REQUIRE_GPIOLIB
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select SMSC_PHY if SH_ETH
-	select SND_SOC_WM8978 if SND_SIMPLE_CARD && I2C
-	select USE_OF
-
 config MACH_BOCKW
 	bool "BOCK-W platform"
 	depends on ARCH_R8A7778
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index 7e20ab3021be0ff2..4ffd7428353b53f9 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -58,7 +58,6 @@ else
 obj-$(CONFIG_MACH_BOCKW)	+= board-bockw.o
 obj-$(CONFIG_MACH_BOCKW_REFERENCE)	+= board-bockw-reference.o
 obj-$(CONFIG_MACH_MARZEN)	+= board-marzen.o
-obj-$(CONFIG_MACH_ARMADILLO800EVA)	+= board-armadillo800eva.o
 endif
 
 # Framework support
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index 2269b1c3c30b108a..14cdfc0ed0755a59 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -1,6 +1,5 @@
 # per-board load address for uImage
 loadaddr-y	:=
-loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000
 loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
 loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
 loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
deleted file mode 100644
index bf37e3c532f661a6..0000000000000000
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ /dev/null
@@ -1,1365 +0,0 @@
-/*
- * armadillo 800 eva board support
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/i2c-gpio.h>
-#include <linux/input.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/mfd/tmio.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mmc/sh_mobile_sdhi.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/platform_data/st1232_pdata.h>
-#include <linux/platform_device.h>
-#include <linux/pwm.h>
-#include <linux/pwm_backlight.h>
-#include <linux/reboot.h>
-#include <linux/regulator/driver.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/gpio-regulator.h>
-#include <linux/regulator/machine.h>
-#include <linux/sh_eth.h>
-#include <linux/usb/renesas_usbhs.h>
-#include <linux/videodev2.h>
-
-#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <asm/page.h>
-#include <media/mt9t112.h>
-#include <media/sh_mobile_ceu.h>
-#include <media/soc_camera.h>
-#include <sound/sh_fsi.h>
-#include <sound/simple_card.h>
-#include <video/sh_mobile_hdmi.h>
-#include <video/sh_mobile_lcdc.h>
-
-#include "common.h"
-#include "irqs.h"
-#include "pm-rmobile.h"
-#include "r8a7740.h"
-#include "sh-gpio.h"
-
-/*
- * CON1		Camera Module
- * CON2		Extension Bus
- * CON3		HDMI Output
- * CON4		Composite Video Output
- * CON5		H-UDI JTAG
- * CON6		ARM JTAG
- * CON7		SD1
- * CON8		SD2
- * CON9		RTC BackUp
- * CON10	Monaural Mic Input
- * CON11	Stereo Headphone Output
- * CON12	Audio Line Output(L)
- * CON13	Audio Line Output(R)
- * CON14	AWL13 Module
- * CON15	Extension
- * CON16	LCD1
- * CON17	LCD2
- * CON19	Power Input
- * CON20	USB1
- * CON21	USB2
- * CON22	Serial
- * CON23	LAN
- * CON24	USB3
- * LED1		Camera LED(Yellow)
- * LED2		Power LED (Green)
- * ED3-LED6	User LED(Yellow)
- * LED7		LAN link LED(Green)
- * LED8		LAN activity LED(Yellow)
- */
-
-/*
- * DipSwitch
- *
- *                    SW1
- *
- * -12345678-+---------------+----------------------------
- *  1        | boot          | hermit
- *  0        | boot          | OS auto boot
- * -12345678-+---------------+----------------------------
- *   00      | boot device   | eMMC
- *   10      | boot device   | SDHI0 (CON7)
- *   01      | boot device   | -
- *   11      | boot device   | Extension Buss (CS0)
- * -12345678-+---------------+----------------------------
- *     0     | Extension Bus | D8-D15 disable, eMMC enable
- *     1     | Extension Bus | D8-D15 enable,  eMMC disable
- * -12345678-+---------------+----------------------------
- *      0    | SDHI1         | COM8 disable, COM14 enable
- *      1    | SDHI1         | COM8 enable,  COM14 disable
- * -12345678-+---------------+----------------------------
- *       0   | USB0          | COM20 enable,  COM24 disable
- *       1   | USB0          | COM20 disable, COM24 enable
- * -12345678-+---------------+----------------------------
- *        00 | JTAG          | SH-X2
- *        10 | JTAG          | ARM
- *        01 | JTAG          | -
- *        11 | JTAG          | Boundary Scan
- *-----------+---------------+----------------------------
- */
-
-/*
- * FSI-WM8978
- *
- * this command is required when playback.
- *
- * # amixer set "Headphone" 50
- *
- * this command is required when capture.
- *
- * # amixer set "Input PGA" 15
- * # amixer set "Left Input Mixer MicP" on
- * # amixer set "Left Input Mixer MicN" on
- * # amixer set "Right Input Mixer MicN" on
- * # amixer set "Right Input Mixer MicP" on
- */
-
-/*
- * USB function
- *
- * When you use USB Function,
- * set SW1.6 ON, and connect cable to CN24.
- *
- * USBF needs workaround on R8A7740 chip.
- * These are a little bit complex.
- * see
- *	usbhsf_power_ctrl()
- */
-#define IRQ7		irq_pin(7)
-#define USBCR1		IOMEM(0xe605810a)
-#define USBH		0xC6700000
-#define USBH_USBCTR	0x10834
-
-struct usbhsf_private {
-	struct clk *phy;
-	struct clk *usb24;
-	struct clk *pci;
-	struct clk *func;
-	struct clk *host;
-	void __iomem *usbh_base;
-	struct renesas_usbhs_platform_info info;
-};
-
-#define usbhsf_get_priv(pdev)				\
-	container_of(renesas_usbhs_get_info(pdev),	\
-		     struct usbhsf_private, info)
-
-static int usbhsf_get_id(struct platform_device *pdev)
-{
-	return USBHS_GADGET;
-}
-
-static int usbhsf_power_ctrl(struct platform_device *pdev,
-			      void __iomem *base, int enable)
-{
-	struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-
-	/*
-	 * Work around for USB Function.
-	 * It needs USB host clock, and settings
-	 */
-	if (enable) {
-		/*
-		 * enable all the related usb clocks
-		 * for usb workaround
-		 */
-		clk_enable(priv->usb24);
-		clk_enable(priv->pci);
-		clk_enable(priv->host);
-		clk_enable(priv->func);
-		clk_enable(priv->phy);
-
-		/*
-		 * set USBCR1
-		 *
-		 * Port1 is driven by USB function,
-		 * Port2 is driven by USB HOST
-		 * One HOST (Port1 or Port2 is HOST)
-		 * USB PLL input clock = 24MHz
-		 */
-		__raw_writew(0xd750, USBCR1);
-		mdelay(1);
-
-		/*
-		 * start USB Host
-		 */
-		__raw_writel(0x0000000c, priv->usbh_base + USBH_USBCTR);
-		__raw_writel(0x00000008, priv->usbh_base + USBH_USBCTR);
-		mdelay(10);
-
-		/*
-		 * USB PHY Power ON
-		 */
-		__raw_writew(0xd770, USBCR1);
-		__raw_writew(0x4000, base + 0x102); /* USBF :: SUSPMODE */
-
-	} else {
-		__raw_writel(0x0000010f, priv->usbh_base + USBH_USBCTR);
-		__raw_writew(0xd7c0, USBCR1); /* GPIO */
-
-		clk_disable(priv->phy);
-		clk_disable(priv->func);	/* usb work around */
-		clk_disable(priv->host);	/* usb work around */
-		clk_disable(priv->pci);		/* usb work around */
-		clk_disable(priv->usb24);	/* usb work around */
-	}
-
-	return 0;
-}
-
-static int usbhsf_get_vbus(struct platform_device *pdev)
-{
-	return gpio_get_value(209);
-}
-
-static irqreturn_t usbhsf_interrupt(int irq, void *data)
-{
-	struct platform_device *pdev = data;
-
-	renesas_usbhs_call_notify_hotplug(pdev);
-
-	return IRQ_HANDLED;
-}
-
-static int usbhsf_hardware_exit(struct platform_device *pdev)
-{
-	struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-
-	if (!IS_ERR(priv->phy))
-		clk_put(priv->phy);
-	if (!IS_ERR(priv->usb24))
-		clk_put(priv->usb24);
-	if (!IS_ERR(priv->pci))
-		clk_put(priv->pci);
-	if (!IS_ERR(priv->host))
-		clk_put(priv->host);
-	if (!IS_ERR(priv->func))
-		clk_put(priv->func);
-	if (priv->usbh_base)
-		iounmap(priv->usbh_base);
-
-	priv->phy	= NULL;
-	priv->usb24	= NULL;
-	priv->pci	= NULL;
-	priv->host	= NULL;
-	priv->func	= NULL;
-	priv->usbh_base	= NULL;
-
-	free_irq(IRQ7, pdev);
-
-	return 0;
-}
-
-static int usbhsf_hardware_init(struct platform_device *pdev)
-{
-	struct usbhsf_private *priv = usbhsf_get_priv(pdev);
-	int ret;
-
-	priv->phy	= clk_get(&pdev->dev, "phy");
-	priv->usb24	= clk_get(&pdev->dev, "usb24");
-	priv->pci	= clk_get(&pdev->dev, "pci");
-	priv->func	= clk_get(&pdev->dev, "func");
-	priv->host	= clk_get(&pdev->dev, "host");
-	priv->usbh_base	= ioremap_nocache(USBH, 0x20000);
-
-	if (IS_ERR(priv->phy)		||
-	    IS_ERR(priv->usb24)		||
-	    IS_ERR(priv->pci)		||
-	    IS_ERR(priv->host)		||
-	    IS_ERR(priv->func)		||
-	    !priv->usbh_base) {
-		dev_err(&pdev->dev, "USB clock setting failed\n");
-		usbhsf_hardware_exit(pdev);
-		return -EIO;
-	}
-
-	ret = request_irq(IRQ7, usbhsf_interrupt, IRQF_TRIGGER_NONE,
-			  dev_name(&pdev->dev), pdev);
-	if (ret) {
-		dev_err(&pdev->dev, "request_irq err\n");
-		return ret;
-	}
-	irq_set_irq_type(IRQ7, IRQ_TYPE_EDGE_BOTH);
-
-	/* usb24 use 1/1 of parent clock (= usb24s = 24MHz) */
-	clk_set_rate(priv->usb24,
-		     clk_get_rate(clk_get_parent(priv->usb24)));
-
-	return 0;
-}
-
-static struct usbhsf_private usbhsf_private = {
-	.info = {
-		.platform_callback = {
-			.get_id		= usbhsf_get_id,
-			.get_vbus	= usbhsf_get_vbus,
-			.hardware_init	= usbhsf_hardware_init,
-			.hardware_exit	= usbhsf_hardware_exit,
-			.power_ctrl	= usbhsf_power_ctrl,
-		},
-		.driver_param = {
-			.buswait_bwait		= 5,
-			.detection_delay	= 5,
-			.d0_rx_id	= SHDMA_SLAVE_USBHS_RX,
-			.d1_tx_id	= SHDMA_SLAVE_USBHS_TX,
-		},
-	}
-};
-
-static struct resource usbhsf_resources[] = {
-	{
-		.name	= "USBHS",
-		.start	= 0xe6890000,
-		.end	= 0xe6890104 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= gic_spi(51),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device usbhsf_device = {
-	.name	= "renesas_usbhs",
-	.dev = {
-		.platform_data = &usbhsf_private.info,
-	},
-	.id = -1,
-	.num_resources	= ARRAY_SIZE(usbhsf_resources),
-	.resource	= usbhsf_resources,
-};
-
-/* Ether */
-static struct sh_eth_plat_data sh_eth_platdata = {
-	.phy			= 0x00, /* LAN8710A */
-	.edmac_endian		= EDMAC_LITTLE_ENDIAN,
-	.phy_interface		= PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource sh_eth_resources[] = {
-	{
-		.start	= 0xe9a00000,
-		.end	= 0xe9a00800 - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.start	= 0xe9a01800,
-		.end	= 0xe9a02000 - 1,
-		.flags	= IORESOURCE_MEM,
-	}, {
-		.start	= gic_spi(110),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device sh_eth_device = {
-	.name = "r8a7740-gether",
-	.id = -1,
-	.dev = {
-		.platform_data = &sh_eth_platdata,
-		.dma_mask = &sh_eth_device.dev.coherent_dma_mask,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-	},
-	.resource = sh_eth_resources,
-	.num_resources = ARRAY_SIZE(sh_eth_resources),
-};
-
-/* PWM */
-static struct resource pwm_resources[] = {
-	[0] = {
-		.start = 0xe6600000,
-		.end = 0xe66000ff,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device pwm_device = {
-	.name = "renesas-tpu-pwm",
-	.id = -1,
-	.num_resources = ARRAY_SIZE(pwm_resources),
-	.resource = pwm_resources,
-};
-
-static struct pwm_lookup pwm_lookup[] = {
-	PWM_LOOKUP("renesas-tpu-pwm", 2, "pwm-backlight.0", NULL,
-		   33333, PWM_POLARITY_INVERSED),
-};
-
-/* LCDC and backlight */
-static struct platform_pwm_backlight_data pwm_backlight_data = {
-	.lth_brightness = 50,
-	.max_brightness = 255,
-	.dft_brightness = 255,
-	.pwm_period_ns = 33333, /* 30kHz */
-	.enable_gpio = 61,
-};
-
-static struct platform_device pwm_backlight_device = {
-	.name = "pwm-backlight",
-	.dev = {
-		.platform_data = &pwm_backlight_data,
-	},
-};
-
-static struct fb_videomode lcdc0_mode = {
-	.name		= "AMPIER/AM-800480",
-	.xres		= 800,
-	.yres		= 480,
-	.left_margin	= 88,
-	.right_margin	= 40,
-	.hsync_len	= 128,
-	.upper_margin	= 20,
-	.lower_margin	= 5,
-	.vsync_len	= 5,
-	.sync		= 0,
-};
-
-static struct sh_mobile_lcdc_info lcdc0_info = {
-	.clock_source	= LCDC_CLK_BUS,
-	.ch[0] = {
-		.chan		= LCDC_CHAN_MAINLCD,
-		.fourcc		= V4L2_PIX_FMT_RGB565,
-		.interface_type	= RGB24,
-		.clock_divider	= 5,
-		.flags		= 0,
-		.lcd_modes	= &lcdc0_mode,
-		.num_modes	= 1,
-		.panel_cfg = {
-			.width	= 111,
-			.height = 68,
-		},
-	},
-};
-
-static struct resource lcdc0_resources[] = {
-	[0] = {
-		.name	= "LCD0",
-		.start	= 0xfe940000,
-		.end	= 0xfe943fff,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= gic_spi(177),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device lcdc0_device = {
-	.name		= "sh_mobile_lcdc_fb",
-	.num_resources	= ARRAY_SIZE(lcdc0_resources),
-	.resource	= lcdc0_resources,
-	.id		= 0,
-	.dev	= {
-		.platform_data	= &lcdc0_info,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-	},
-};
-
-/*
- * LCDC1/HDMI
- */
-static struct sh_mobile_hdmi_info hdmi_info = {
-	.flags		= HDMI_OUTPUT_PUSH_PULL |
-			  HDMI_OUTPUT_POLARITY_HI |
-			  HDMI_32BIT_REG |
-			  HDMI_HAS_HTOP1 |
-			  HDMI_SND_SRC_SPDIF,
-};
-
-static struct resource hdmi_resources[] = {
-	[0] = {
-		.name	= "HDMI",
-		.start	= 0xe6be0000,
-		.end	= 0xe6be03ff,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= gic_spi(131),
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.name	= "HDMI emma3pf",
-		.start	= 0xe6be4000,
-		.end	= 0xe6be43ff,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device hdmi_device = {
-	.name		= "sh-mobile-hdmi",
-	.num_resources	= ARRAY_SIZE(hdmi_resources),
-	.resource	= hdmi_resources,
-	.id             = -1,
-	.dev	= {
-		.platform_data	= &hdmi_info,
-	},
-};
-
-static const struct fb_videomode lcdc1_mode = {
-	.name		= "HDMI 720p",
-	.xres		= 1280,
-	.yres		= 720,
-	.pixclock	= 13468,
-	.left_margin	= 220,
-	.right_margin	= 110,
-	.hsync_len	= 40,
-	.upper_margin	= 20,
-	.lower_margin	= 5,
-	.vsync_len	= 5,
-	.refresh	= 60,
-	.sync		= FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
-};
-
-static struct sh_mobile_lcdc_info hdmi_lcdc_info = {
-	.clock_source	= LCDC_CLK_PERIPHERAL, /* HDMI clock */
-	.ch[0] = {
-		.chan			= LCDC_CHAN_MAINLCD,
-		.fourcc			= V4L2_PIX_FMT_RGB565,
-		.interface_type		= RGB24,
-		.clock_divider		= 1,
-		.flags			= LCDC_FLAGS_DWPOL,
-		.lcd_modes		= &lcdc1_mode,
-		.num_modes		= 1,
-		.tx_dev			= &hdmi_device,
-		.panel_cfg = {
-			.width	= 1280,
-			.height = 720,
-		},
-	},
-};
-
-static struct resource hdmi_lcdc_resources[] = {
-	[0] = {
-		.name	= "LCDC1",
-		.start	= 0xfe944000,
-		.end	= 0xfe948000 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= gic_spi(178),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device hdmi_lcdc_device = {
-	.name		= "sh_mobile_lcdc_fb",
-	.num_resources	= ARRAY_SIZE(hdmi_lcdc_resources),
-	.resource	= hdmi_lcdc_resources,
-	.id		= 1,
-	.dev	= {
-		.platform_data	= &hdmi_lcdc_info,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-	},
-};
-
-/* LEDS */
-static struct gpio_led gpio_leds[] = {
-	{
-		.name		= "LED3",
-		.gpio		= 102,
-		.default_state	= LEDS_GPIO_DEFSTATE_ON,
-	}, {
-		.name		= "LED4",
-		.gpio		= 111,
-		.default_state	= LEDS_GPIO_DEFSTATE_ON,
-	}, {
-		.name		= "LED5",
-		.gpio		= 110,
-		.default_state	= LEDS_GPIO_DEFSTATE_ON,
-	}, {
-		.name		= "LED6",
-		.gpio		= 177,
-		.default_state	= LEDS_GPIO_DEFSTATE_ON,
-	},
-};
-
-static struct gpio_led_platform_data leds_gpio_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio_device = {
-	.name   = "leds-gpio",
-	.id     = -1,
-	.dev    = {
-		.platform_data  = &leds_gpio_info,
-	},
-};
-
-/* GPIO KEY */
-#define GPIO_KEY(c, g, d, ...) \
-	{ .code = c, .gpio = g, .desc = d, .active_low = 1, __VA_ARGS__ }
-
-static struct gpio_keys_button gpio_buttons[] = {
-	GPIO_KEY(KEY_POWER,	99,	"SW3", .wakeup = 1),
-	GPIO_KEY(KEY_BACK,	100,	"SW4"),
-	GPIO_KEY(KEY_MENU,	97,	"SW5"),
-	GPIO_KEY(KEY_HOME,	98,	"SW6"),
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device gpio_keys_device = {
-	.name   = "gpio-keys",
-	.id     = -1,
-	.dev    = {
-		.platform_data  = &gpio_key_info,
-	},
-};
-
-/* Fixed 3.3V regulator to be used by SDHI1, MMCIF */
-static struct regulator_consumer_supply fixed3v3_power_consumers[] = {
-	REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
-	REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
-};
-
-/* Fixed 3.3V regulator used by LCD backlight */
-static struct regulator_consumer_supply fixed5v0_power_consumers[] = {
-	REGULATOR_SUPPLY("power", "pwm-backlight.0"),
-};
-
-/* Fixed 3.3V regulator to be used by SDHI0 */
-static struct regulator_consumer_supply vcc_sdhi0_consumers[] = {
-	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vcc_sdhi0_init_data = {
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(vcc_sdhi0_consumers),
-	.consumer_supplies      = vcc_sdhi0_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi0_info = {
-	.supply_name = "SDHI0 Vcc",
-	.microvolts = 3300000,
-	.gpio = 75,
-	.enable_high = 1,
-	.init_data = &vcc_sdhi0_init_data,
-};
-
-static struct platform_device vcc_sdhi0 = {
-	.name = "reg-fixed-voltage",
-	.id   = 1,
-	.dev  = {
-		.platform_data = &vcc_sdhi0_info,
-	},
-};
-
-/* 1.8 / 3.3V SDHI0 VccQ regulator */
-static struct regulator_consumer_supply vccq_sdhi0_consumers[] = {
-	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
-};
-
-static struct regulator_init_data vccq_sdhi0_init_data = {
-	.constraints = {
-		.input_uV	= 3300000,
-		.min_uV		= 1800000,
-		.max_uV         = 3300000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-				  REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(vccq_sdhi0_consumers),
-	.consumer_supplies      = vccq_sdhi0_consumers,
-};
-
-static struct gpio vccq_sdhi0_gpios[] = {
-	{17, GPIOF_OUT_INIT_LOW, "vccq-sdhi0" },
-};
-
-static struct gpio_regulator_state vccq_sdhi0_states[] = {
-	{ .value = 3300000, .gpios = (0 << 0) },
-	{ .value = 1800000, .gpios = (1 << 0) },
-};
-
-static struct gpio_regulator_config vccq_sdhi0_info = {
-	.supply_name = "vqmmc",
-
-	.enable_gpio = 74,
-	.enable_high = 1,
-	.enabled_at_boot = 0,
-
-	.gpios = vccq_sdhi0_gpios,
-	.nr_gpios = ARRAY_SIZE(vccq_sdhi0_gpios),
-
-	.states = vccq_sdhi0_states,
-	.nr_states = ARRAY_SIZE(vccq_sdhi0_states),
-
-	.type = REGULATOR_VOLTAGE,
-	.init_data = &vccq_sdhi0_init_data,
-};
-
-static struct platform_device vccq_sdhi0 = {
-	.name = "gpio-regulator",
-	.id   = -1,
-	.dev  = {
-		.platform_data = &vccq_sdhi0_info,
-	},
-};
-
-/* Fixed 3.3V regulator to be used by SDHI1 */
-static struct regulator_consumer_supply vcc_sdhi1_consumers[] = {
-	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
-};
-
-static struct regulator_init_data vcc_sdhi1_init_data = {
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(vcc_sdhi1_consumers),
-	.consumer_supplies      = vcc_sdhi1_consumers,
-};
-
-static struct fixed_voltage_config vcc_sdhi1_info = {
-	.supply_name = "SDHI1 Vcc",
-	.microvolts = 3300000,
-	.gpio = 16,
-	.enable_high = 1,
-	.init_data = &vcc_sdhi1_init_data,
-};
-
-static struct platform_device vcc_sdhi1 = {
-	.name = "reg-fixed-voltage",
-	.id   = 2,
-	.dev  = {
-		.platform_data = &vcc_sdhi1_info,
-	},
-};
-
-/* SDHI0 */
-static struct tmio_mmc_data sdhi0_info = {
-	.chan_priv_tx	= (void *)SHDMA_SLAVE_SDHI0_TX,
-	.chan_priv_rx	= (void *)SHDMA_SLAVE_SDHI0_RX,
-	.capabilities	= MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
-			  MMC_CAP_POWER_OFF_CARD,
-	.flags		= TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
-	.cd_gpio	= 167,
-};
-
-static struct resource sdhi0_resources[] = {
-	{
-		.name	= "SDHI0",
-		.start	= 0xe6850000,
-		.end	= 0xe6850100 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	/*
-	 * no SH_MOBILE_SDHI_IRQ_CARD_DETECT here
-	 */
-	{
-		.name	= SH_MOBILE_SDHI_IRQ_SDCARD,
-		.start	= gic_spi(118),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.name	= SH_MOBILE_SDHI_IRQ_SDIO,
-		.start	= gic_spi(119),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device sdhi0_device = {
-	.name		= "sh_mobile_sdhi",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &sdhi0_info,
-	},
-	.num_resources	= ARRAY_SIZE(sdhi0_resources),
-	.resource	= sdhi0_resources,
-};
-
-/* SDHI1 */
-static struct tmio_mmc_data sdhi1_info = {
-	.chan_priv_tx	= (void *)SHDMA_SLAVE_SDHI1_TX,
-	.chan_priv_rx	= (void *)SHDMA_SLAVE_SDHI1_RX,
-	.capabilities	= MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
-			  MMC_CAP_POWER_OFF_CARD,
-	.flags		= TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
-	/* Port72 cannot generate IRQs, will be used in polling mode. */
-	.cd_gpio	= 72,
-};
-
-static struct resource sdhi1_resources[] = {
-	[0] = {
-		.name	= "SDHI1",
-		.start	= 0xe6860000,
-		.end	= 0xe6860100 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= gic_spi(121),
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start	= gic_spi(122),
-		.flags	= IORESOURCE_IRQ,
-	},
-	[3] = {
-		.start	= gic_spi(123),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device sdhi1_device = {
-	.name		= "sh_mobile_sdhi",
-	.id		= 1,
-	.dev		= {
-		.platform_data	= &sdhi1_info,
-	},
-	.num_resources	= ARRAY_SIZE(sdhi1_resources),
-	.resource	= sdhi1_resources,
-};
-
-static const struct pinctrl_map eva_sdhi1_pinctrl_map[] = {
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
-				  "sdhi1_data4", "sdhi1"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
-				  "sdhi1_ctrl", "sdhi1"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
-				  "sdhi1_cd", "sdhi1"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-r8a7740",
-				  "sdhi1_wp", "sdhi1"),
-};
-
-/* MMCIF */
-static struct sh_mmcif_plat_data sh_mmcif_plat = {
-	.sup_pclk	= 0,
-	.caps		= MMC_CAP_4_BIT_DATA |
-			  MMC_CAP_8_BIT_DATA |
-			  MMC_CAP_NONREMOVABLE,
-	.ccs_unsupported = true,
-	.slave_id_tx	= SHDMA_SLAVE_MMCIF_TX,
-	.slave_id_rx	= SHDMA_SLAVE_MMCIF_RX,
-};
-
-static struct resource sh_mmcif_resources[] = {
-	[0] = {
-		.name	= "MMCIF",
-		.start	= 0xe6bd0000,
-		.end	= 0xe6bd0100 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		/* MMC ERR */
-		.start	= gic_spi(56),
-		.flags	= IORESOURCE_IRQ,
-	},
-	[2] = {
-		/* MMC NOR */
-		.start	= gic_spi(57),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device sh_mmcif_device = {
-	.name		= "sh_mmcif",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &sh_mmcif_plat,
-	},
-	.num_resources	= ARRAY_SIZE(sh_mmcif_resources),
-	.resource	= sh_mmcif_resources,
-};
-
-/* Camera */
-static int mt9t111_power(struct device *dev, int mode)
-{
-	struct clk *mclk = clk_get(NULL, "video1");
-
-	if (IS_ERR(mclk)) {
-		dev_err(dev, "can't get video1 clock\n");
-		return -EINVAL;
-	}
-
-	if (mode) {
-		/* video1 (= CON1 camera) expect 24MHz */
-		clk_set_rate(mclk, clk_round_rate(mclk, 24000000));
-		clk_enable(mclk);
-		gpio_set_value(158, 1);
-	} else {
-		gpio_set_value(158, 0);
-		clk_disable(mclk);
-	}
-
-	clk_put(mclk);
-
-	return 0;
-}
-
-static struct i2c_board_info i2c_camera_mt9t111 = {
-	I2C_BOARD_INFO("mt9t112", 0x3d),
-};
-
-static struct mt9t112_camera_info mt9t111_info = {
-	.divider = { 16, 0, 0, 7, 0, 10, 14, 7, 7 },
-};
-
-static struct soc_camera_link mt9t111_link = {
-	.i2c_adapter_id	= 0,
-	.bus_id		= 0,
-	.board_info	= &i2c_camera_mt9t111,
-	.power		= mt9t111_power,
-	.priv		= &mt9t111_info,
-};
-
-static struct platform_device camera_device = {
-	.name	= "soc-camera-pdrv",
-	.id	= 0,
-	.dev	= {
-		.platform_data = &mt9t111_link,
-	},
-};
-
-/* CEU0 */
-static struct sh_mobile_ceu_info sh_mobile_ceu0_info = {
-	.flags = SH_CEU_FLAG_LOWER_8BIT,
-};
-
-static struct resource ceu0_resources[] = {
-	[0] = {
-		.name	= "CEU",
-		.start	= 0xfe910000,
-		.end	= 0xfe91009f,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start  = gic_spi(160),
-		.flags  = IORESOURCE_IRQ,
-	},
-	[2] = {
-		/* place holder for contiguous memory */
-	},
-};
-
-static struct platform_device ceu0_device = {
-	.name		= "sh_mobile_ceu",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(ceu0_resources),
-	.resource	= ceu0_resources,
-	.dev	= {
-		.platform_data		= &sh_mobile_ceu0_info,
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-/* FSI */
-static struct sh_fsi_platform_info fsi_info = {
-	/* FSI-WM8978 */
-	.port_a = {
-		.tx_id = SHDMA_SLAVE_FSIA_TX,
-	},
-	/* FSI-HDMI */
-	.port_b = {
-		.flags		= SH_FSI_FMT_SPDIF |
-				  SH_FSI_ENABLE_STREAM_MODE |
-				  SH_FSI_CLK_CPG,
-		.tx_id		= SHDMA_SLAVE_FSIB_TX,
-	}
-};
-
-static struct resource fsi_resources[] = {
-	[0] = {
-		.name	= "FSI",
-		.start	= 0xfe1f0000,
-		.end	= 0xfe1f0400 - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start  = gic_spi(9),
-		.flags  = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device fsi_device = {
-	.name		= "sh_fsi2",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(fsi_resources),
-	.resource	= fsi_resources,
-	.dev	= {
-		.platform_data	= &fsi_info,
-	},
-};
-
-/* FSI-WM8978 */
-static struct asoc_simple_card_info fsi_wm8978_info = {
-	.name		= "wm8978",
-	.card		= "FSI2A-WM8978",
-	.codec		= "wm8978.0-001a",
-	.platform	= "sh_fsi2",
-	.daifmt		= SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM,
-	.cpu_dai = {
-		.name	= "fsia-dai",
-	},
-	.codec_dai = {
-		.name	= "wm8978-hifi",
-		.sysclk	= 12288000,
-	},
-};
-
-static struct platform_device fsi_wm8978_device = {
-	.name	= "asoc-simple-card",
-	.id	= 0,
-	.dev	= {
-		.platform_data	= &fsi_wm8978_info,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.dma_mask = &fsi_wm8978_device.dev.coherent_dma_mask,
-	},
-};
-
-/* FSI-HDMI */
-static struct asoc_simple_card_info fsi2_hdmi_info = {
-	.name		= "HDMI",
-	.card		= "FSI2B-HDMI",
-	.codec		= "sh-mobile-hdmi",
-	.platform	= "sh_fsi2",
-	.daifmt		= SND_SOC_DAIFMT_CBS_CFS,
-	.cpu_dai = {
-		.name	= "fsib-dai",
-	},
-	.codec_dai = {
-		.name = "sh_mobile_hdmi-hifi",
-	},
-};
-
-static struct platform_device fsi_hdmi_device = {
-	.name	= "asoc-simple-card",
-	.id	= 1,
-	.dev	= {
-		.platform_data	= &fsi2_hdmi_info,
-		.coherent_dma_mask = DMA_BIT_MASK(32),
-		.dma_mask = &fsi_hdmi_device.dev.coherent_dma_mask,
-	},
-};
-
-/* RTC: RTC connects i2c-gpio. */
-static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin	= 208,
-	.scl_pin	= 91,
-	.udelay		= 5, /* 100 kHz */
-};
-
-static struct platform_device i2c_gpio_device = {
-	.name = "i2c-gpio",
-	.id = 2,
-	.dev = {
-		.platform_data = &i2c_gpio_data,
-	},
-};
-
-/* I2C */
-static struct st1232_pdata st1232_i2c0_pdata = {
-	.reset_gpio = 166,
-};
-
-static struct i2c_board_info i2c0_devices[] = {
-	{
-		I2C_BOARD_INFO("st1232-ts", 0x55),
-		.irq = irq_pin(10),
-		.platform_data = &st1232_i2c0_pdata,
-	},
-	{
-		I2C_BOARD_INFO("wm8978", 0x1a),
-	},
-};
-
-static struct i2c_board_info i2c2_devices[] = {
-	{
-		I2C_BOARD_INFO("s35390a", 0x30),
-		.type = "s35390a",
-	},
-};
-
-/*
- * board devices
- */
-static struct platform_device *eva_devices[] __initdata = {
-	&lcdc0_device,
-	&pwm_device,
-	&pwm_backlight_device,
-	&leds_gpio_device,
-	&gpio_keys_device,
-	&sh_eth_device,
-	&vcc_sdhi0,
-	&vccq_sdhi0,
-	&sdhi0_device,
-	&sh_mmcif_device,
-	&hdmi_device,
-	&hdmi_lcdc_device,
-	&camera_device,
-	&ceu0_device,
-	&fsi_device,
-	&fsi_wm8978_device,
-	&fsi_hdmi_device,
-	&i2c_gpio_device,
-};
-
-static const struct pinctrl_map eva_pinctrl_map[] = {
-	/* CEU0 */
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
-				  "ceu0_data_0_7", "ceu0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
-				  "ceu0_clk_0", "ceu0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
-				  "ceu0_sync", "ceu0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
-				  "ceu0_field", "ceu0"),
-	/* FSIA */
-	PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
-				  "fsia_sclk_in", "fsia"),
-	PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
-				  "fsia_mclk_out", "fsia"),
-	PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
-				  "fsia_data_in_1", "fsia"),
-	PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
-				  "fsia_data_out_0", "fsia"),
-	/* FSIB */
-	PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.1", "pfc-r8a7740",
-				  "fsib_mclk_in", "fsib"),
-	/* GETHER */
-	PIN_MAP_MUX_GROUP_DEFAULT("r8a7740-gether", "pfc-r8a7740",
-				  "gether_mii", "gether"),
-	PIN_MAP_MUX_GROUP_DEFAULT("r8a7740-gether", "pfc-r8a7740",
-				  "gether_int", "gether"),
-	/* HDMI */
-	PIN_MAP_MUX_GROUP_DEFAULT("sh-mobile-hdmi", "pfc-r8a7740",
-				  "hdmi", "hdmi"),
-	/* LCD0 */
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
-				  "lcd0_data24_0", "lcd0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
-				  "lcd0_lclk_1", "lcd0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
-				  "lcd0_sync", "lcd0"),
-	/* MMCIF */
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
-				  "mmc0_data8_1", "mmc0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
-				  "mmc0_ctrl_1", "mmc0"),
-	/* SCIFA1 */
-	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.1", "pfc-r8a7740",
-				  "scifa1_data", "scifa1"),
-	/* SDHI0 */
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
-				  "sdhi0_data4", "sdhi0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
-				  "sdhi0_ctrl", "sdhi0"),
-	PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
-				  "sdhi0_wp", "sdhi0"),
-	/* ST1232 */
-	PIN_MAP_MUX_GROUP_DEFAULT("0-0055", "pfc-r8a7740",
-				  "intc_irq10", "intc"),
-	/* TPU0 */
-	PIN_MAP_MUX_GROUP_DEFAULT("renesas-tpu-pwm", "pfc-r8a7740",
-				  "tpu0_to2_1", "tpu0"),
-	/* USBHS */
-	PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-r8a7740",
-				  "intc_irq7_1", "intc"),
-};
-
-static void __init eva_clock_init(void)
-{
-	struct clk *system	= clk_get(NULL, "system_clk");
-	struct clk *xtal1	= clk_get(NULL, "extal1");
-	struct clk *usb24s	= clk_get(NULL, "usb24s");
-	struct clk *fsibck	= clk_get(NULL, "fsibck");
-
-	if (IS_ERR(system)	||
-	    IS_ERR(xtal1)	||
-	    IS_ERR(usb24s)	||
-	    IS_ERR(fsibck)) {
-		pr_err("armadillo800eva board clock init failed\n");
-		goto clock_error;
-	}
-
-	/* armadillo 800 eva extal1 is 24MHz */
-	clk_set_rate(xtal1, 24000000);
-
-	/* usb24s use extal1 (= system) clock (= 24MHz) */
-	clk_set_parent(usb24s, system);
-
-	/* FSIBCK is 12.288MHz, and it is parent of FSI-B */
-	clk_set_rate(fsibck, 12288000);
-
-clock_error:
-	if (!IS_ERR(system))
-		clk_put(system);
-	if (!IS_ERR(xtal1))
-		clk_put(xtal1);
-	if (!IS_ERR(usb24s))
-		clk_put(usb24s);
-	if (!IS_ERR(fsibck))
-		clk_put(fsibck);
-}
-
-/*
- * board init
- */
-#define GPIO_PORT7CR	IOMEM(0xe6050007)
-#define GPIO_PORT8CR	IOMEM(0xe6050008)
-static void __init eva_init(void)
-{
-	static struct pm_domain_device domain_devices[] __initdata = {
-		{ "A4LC", &lcdc0_device },
-		{ "A4LC", &hdmi_lcdc_device },
-		{ "A4MP", &hdmi_device },
-		{ "A4MP", &fsi_device },
-		{ "A4R",  &ceu0_device },
-		{ "A4S",  &sh_eth_device },
-		{ "A3SP", &pwm_device },
-		{ "A3SP", &sdhi0_device },
-		{ "A3SP", &sh_mmcif_device },
-	};
-	struct platform_device *usb = NULL, *sdhi1 = NULL;
-
-	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
-				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
-	regulator_register_always_on(3, "fixed-5.0V", fixed5v0_power_consumers,
-				     ARRAY_SIZE(fixed5v0_power_consumers), 5000000);
-
-	pinctrl_register_mappings(eva_pinctrl_map, ARRAY_SIZE(eva_pinctrl_map));
-	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-
-	r8a7740_pinmux_init();
-	r8a7740_meram_workaround();
-
-	/* GETHER */
-	gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
-
-	/* USB */
-	gpio_request_one(159, GPIOF_IN, NULL); /* USB_DEVICE_MODE */
-
-	if (gpio_get_value(159)) {
-		/* USB Host */
-	} else {
-		/* USB Func */
-		/*
-		 * The USBHS interrupt handlers needs to read the IRQ pin value
-		 * (HI/LOW) to diffentiate USB connection and disconnection
-		 * events (usbhsf_get_vbus()). We thus need to select both the
-		 * intc_irq7_1 pin group and GPIO 209 here.
-		 */
-		gpio_request_one(209, GPIOF_IN, NULL);
-
-		platform_device_register(&usbhsf_device);
-		usb = &usbhsf_device;
-	}
-
-	/* CON1/CON15 Camera */
-	gpio_request_one(173, GPIOF_OUT_INIT_LOW, NULL);  /* STANDBY */
-	gpio_request_one(172, GPIOF_OUT_INIT_HIGH, NULL); /* RST */
-	/* see mt9t111_power() */
-	gpio_request_one(158, GPIOF_OUT_INIT_LOW, NULL);  /* CAM_PON */
-
-	/* FSI-WM8978 */
-	gpio_request(7, NULL);
-	gpio_request(8, NULL);
-	gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
-	gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
-
-	/*
-	 * CAUTION
-	 *
-	 * DBGMD/LCDC0/FSIA MUX
-	 * DBGMD_SELECT_B should be set after setting PFC Function.
-	 */
-	gpio_request_one(176, GPIOF_OUT_INIT_HIGH, NULL);
-
-	/*
-	 * We can switch CON8/CON14 by SW1.5,
-	 * but it needs after DBGMD_SELECT_B
-	 */
-	gpio_request_one(6, GPIOF_IN, NULL);
-	if (gpio_get_value(6)) {
-		/* CON14 enable */
-	} else {
-		/* CON8 (SDHI1) enable */
-		pinctrl_register_mappings(eva_sdhi1_pinctrl_map,
-					  ARRAY_SIZE(eva_sdhi1_pinctrl_map));
-
-		platform_device_register(&vcc_sdhi1);
-		platform_device_register(&sdhi1_device);
-		sdhi1 = &sdhi1_device;
-	}
-
-
-#ifdef CONFIG_CACHE_L2X0
-	/* Shared attribute override enable, 32K*8way */
-	l2x0_init(IOMEM(0xf0002000), 0x00400000, 0xc20f0fff);
-#endif
-
-	i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
-	i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices));
-
-	r8a7740_add_standard_devices();
-
-	platform_add_devices(eva_devices,
-			     ARRAY_SIZE(eva_devices));
-
-	rmobile_add_devices_to_domains(domain_devices,
-				       ARRAY_SIZE(domain_devices));
-	if (usb)
-		rmobile_add_device_to_domain("A3SP", usb);
-	if (sdhi1)
-		rmobile_add_device_to_domain("A3SP", sdhi1);
-
-	r8a7740_pm_init();
-}
-
-static void __init eva_earlytimer_init(void)
-{
-	r8a7740_clock_init(MD_CK0 | MD_CK2);
-	shmobile_earlytimer_init();
-
-	/* the rate of extal1 clock must be set before late_time_init */
-	eva_clock_init();
-}
-
-#define RESCNT2 IOMEM(0xe6188020)
-static void eva_restart(enum reboot_mode mode, const char *cmd)
-{
-	/* Do soft power on reset */
-	writel((1 << 31), RESCNT2);
-}
-
-static const char *eva_boards_compat_dt[] __initdata = {
-	"renesas,armadillo800eva",
-	NULL,
-};
-
-DT_MACHINE_START(ARMADILLO800EVA_DT, "armadillo800eva")
-	.map_io		= r8a7740_map_io,
-	.init_early	= r8a7740_add_early_devices,
-	.init_irq	= r8a7740_init_irq_of,
-	.init_machine	= eva_init,
-	.init_late	= shmobile_init_late,
-	.init_time	= eva_earlytimer_init,
-	.dt_compat	= eva_boards_compat_dt,
-	.restart	= eva_restart,
-MACHINE_END
