@@ -3,8 +3,8 @@ USB xHCI controllers
Required properties:
- compatible: should be one of "generic-xhci",
"marvell,armada-375-xhci", "marvell,armada-380-xhci",
- "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793"
- (deprecated: "xhci-platform").
+ "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793",
+ "renesas,xhci-r8a7795" (deprecated: "xhci-platform").
- reg: should contain address and length of the standard XHCI
register set for the device.
- interrupts: one XHCI interrupt should be described here.
@@ -52,7 +52,8 @@ static int xhci_plat_setup(struct usb_hcd *hcd)
{
int ret;
- if (xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2)) {
+ if (xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2) ||
+ xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN3)) {
ret = xhci_rcar_init_quirk(hcd);
if (ret)
return ret;
@@ -63,7 +64,8 @@ static int xhci_plat_setup(struct usb_hcd *hcd)
static int xhci_plat_start(struct usb_hcd *hcd)
{
- if (xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2))
+ if (xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2) ||
+ xhci_plat_type_is(hcd, XHCI_PLAT_TYPE_RENESAS_RCAR_GEN3))
xhci_rcar_start(hcd);
return xhci_run(hcd);
@@ -79,6 +81,11 @@ static const struct xhci_plat_priv xhci_plat_renesas_rcar_gen2 = {
.firmware_name = XHCI_RCAR_FIRMWARE_NAME_V1,
};
+static const struct xhci_plat_priv xhci_plat_renesas_rcar_gen3 = {
+ .type = XHCI_PLAT_TYPE_RENESAS_RCAR_GEN3,
+ .firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2,
+};
+
static const struct of_device_id usb_xhci_of_match[] = {
{
.compatible = "generic-xhci",
@@ -100,6 +107,9 @@ static const struct of_device_id usb_xhci_of_match[] = {
.compatible = "renesas,xhci-r8a7793",
.data = &xhci_plat_renesas_rcar_gen2,
}, {
+ .compatible = "renesas,xhci-r8a7795",
+ .data = &xhci_plat_renesas_rcar_gen3,
+ }, {
},
};
MODULE_DEVICE_TABLE(of, usb_xhci_of_match);
@@ -16,6 +16,7 @@
enum xhci_plat_type {
XHCI_PLAT_TYPE_MARVELL_ARMADA,
XHCI_PLAT_TYPE_RENESAS_RCAR_GEN2,
+ XHCI_PLAT_TYPE_RENESAS_RCAR_GEN3,
};
struct xhci_plat_priv {
@@ -17,7 +17,14 @@
#include "xhci-plat.h"
#include "xhci-rcar.h"
+/*
+* - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
+* performance degradation. So, this driver continues to use the V1 if R-Car
+* Gen2.
+* - The V1 firmware is impossible to use on R-Car Gen3.
+*/
MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
+MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
/*** Register Offset ***/
#define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */
@@ -12,6 +12,7 @@
#define _XHCI_RCAR_H
#define XHCI_RCAR_FIRMWARE_NAME_V1 "r8a779x_usb3_v1.dlmem"
+#define XHCI_RCAR_FIRMWARE_NAME_V2 "r8a779x_usb3_v2.dlmem"
#if IS_ENABLED(CONFIG_USB_XHCI_RCAR)
void xhci_rcar_start(struct usb_hcd *hcd);
The R-Car H3 has two xHCI controllers. This SoC is compatible with R-Car Gen2 SoCs, however this SoC doesn't need some specific registers setting, and need a new firmware. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> --- Documentation/devicetree/bindings/usb/usb-xhci.txt | 4 ++-- drivers/usb/host/xhci-plat.c | 14 ++++++++++++-- drivers/usb/host/xhci-plat.h | 1 + drivers/usb/host/xhci-rcar.c | 7 +++++++ drivers/usb/host/xhci-rcar.h | 1 + 5 files changed, 23 insertions(+), 4 deletions(-)