| Message ID | 201303312354.20695.sergei.shtylyov@cogentembedded.com (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Date: Sun, 31 Mar 2013 23:54:20 +0400 > At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its > mask in EESIPR register. I can 100% reproduce it with the following scenario: > target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device > but doesn't get a proper reply and then succeeds with on-board SMC chip; then > I login and try to bring up the SoC Ether device with 'ifconfig', and I get > an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt > mask in EESIPR register is all 0), if that interrupt is accompanied by a pending > EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx() > because sh_eth_ring_init() hasn't been called yet! > > The solution I worked out is the following: in sh_eth_interrupt(), mask the > interrupt status from EESR register with the interrupt mask from EESIPR register > in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit > in this mask set because we always need to fully handle EESR.ECI interrupt in > sh_eth_error() in order to quench it (as it doesn't get cleared by just writing > 1 to the this bit as all the other interrupts). > > While at it, remove unneeded initializer for 'intr_status' variable and give it > *unsigned long* type, matching the type of sh_eth_read()'s result; fix comment. > > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > Reviewed-by: Max Filippov <max.filippov@cogentembedded.com> Applied. -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello. On 31-03-2013 23:54, Sergei Shtylyov wrote: > At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its > mask in EESIPR register. I can 100% reproduce it with the following scenario: > target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device > but doesn't get a proper reply and then succeeds with on-board SMC chip; then > I login and try to bring up the SoC Ether device with 'ifconfig', and I get > an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt > mask in EESIPR register is all 0), if that interrupt is accompanied by a pending > EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx() > because sh_eth_ring_init() hasn't been called yet! > The solution I worked out is the following: in sh_eth_interrupt(), mask the > interrupt status from EESR register with the interrupt mask from EESIPR register > in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit > in this mask set because we always need to fully handle EESR.ECI interrupt in > sh_eth_error() in order to quench it (as it doesn't get cleared by just writing > 1 to the this bit as all the other interrupts). > While at it, remove unneeded initializer for 'intr_status' variable and give it > *unsigned long* type, matching the type of sh_eth_read()'s result; fix comment. > Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> > Reviewed-by: Max Filippov <max.filippov@cogentembedded.com> Though maybe writing 0 to ECSIPR (feLic interrupt mask) register in sh_eth_close() could have prevented the spurious interrupts too, masking all its primary sources -- I should have tried it beforehand. Still can try though... WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-sh" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Index: net/drivers/net/ethernet/renesas/sh_eth.c =================================================================== --- net.orig/drivers/net/ethernet/renesas/sh_eth.c +++ net/drivers/net/ethernet/renesas/sh_eth.c @@ -1324,12 +1324,18 @@ static irqreturn_t sh_eth_interrupt(int struct sh_eth_private *mdp = netdev_priv(ndev); struct sh_eth_cpu_data *cd = mdp->cd; irqreturn_t ret = IRQ_NONE; - u32 intr_status = 0; + unsigned long intr_status; spin_lock(&mdp->lock); - /* Get interrpt stat */ + /* Get interrupt status */ intr_status = sh_eth_read(ndev, EESR); + /* Mask it with the interrupt mask, forcing ECI interrupt to be always + * enabled since it's the one that comes thru regardless of the mask, + * and we need to fully handle it in sh_eth_error() in order to quench + * it as it doesn't get cleared by just writing 1 to the ECI bit... + */ + intr_status &= sh_eth_read(ndev, EESIPR) | DMAC_M_ECI; /* Clear interrupt */ if (intr_status & (EESR_FRC | EESR_RMAF | EESR_RRF | EESR_RTLF | EESR_RTSF | EESR_PRE | EESR_CERF |