@@ -144,45 +144,32 @@ struct mtu3_fifo_info {
* The format of TX GPD is a little different from RX one.
* And the size of GPD is 16 bytes.
*
- * @flag:
+ * @dw0_info:
* bit0: Hardware Own (HWO)
* bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported
* bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1
* bit7: Interrupt On Completion (IOC)
- * @chksum: This is used to validate the contents of this GPD;
- * If TXQ_CS_EN / RXQ_CS_EN bit is set, an interrupt is issued
- * when checksum validation fails;
- * Checksum value is calculated over the 16 bytes of the GPD by default;
- * @data_buf_len (RX ONLY): This value indicates the length of
- * the assigned data buffer
- * @tx_ext_addr (TX ONLY): [3:0] are 4 extension bits of @buffer,
- * [7:4] are 4 extension bits of @next_gpd
+ * bit[31:16]: allow data buffer length (RX ONLY),
+ * the buffer length of the data to receive
+ * bit[23:16]: extension address (TX ONLY),
+ * lower 4 bits are extension bits of @buffer,
+ * upper 4 bits are extension bits of @next_gpd
* @next_gpd: Physical address of the next GPD
* @buffer: Physical address of the data buffer
- * @buf_len:
- * (TX): This value indicates the length of the assigned data buffer
- * (RX): The total length of data received
- * @ext_len: reserved
- * @rx_ext_addr(RX ONLY): [3:0] are 4 extension bits of @buffer,
- * [7:4] are 4 extension bits of @next_gpd
- * @ext_flag:
- * bit5 (TX ONLY): Zero Length Packet (ZLP),
+ * @dw3_info:
+ * bit[15:0]: data buffer length,
+ * (TX): the buffer length of the data to transmit
+ * (RX): The total length of data received
+ * bit[23:16]: extension address (RX ONLY),
+ * lower 4 bits are extension bits of @buffer,
+ * upper 4 bits are extension bits of @next_gpd
+ * bit29: Zero Length Packet (ZLP) (TX ONLY)
*/
struct qmu_gpd {
- __u8 flag;
- __u8 chksum;
- union {
- __le16 data_buf_len;
- __le16 tx_ext_addr;
- };
+ __le32 dw0_info;
__le32 next_gpd;
__le32 buffer;
- __le16 buf_len;
- union {
- __u8 ext_len;
- __u8 rx_ext_addr;
- };
- __u8 ext_flag;
+ __le32 dw3_info;
} __packed;
/**
@@ -29,10 +29,13 @@
#define GPD_FLAGS_BDP BIT(1)
#define GPD_FLAGS_BPS BIT(2)
#define GPD_FLAGS_IOC BIT(7)
+#define GET_GPD_HWO(gpd) (le32_to_cpu((gpd)->dw0_info) & GPD_FLAGS_HWO)
-#define GPD_EXT_FLAG_ZLP BIT(5)
-#define GPD_EXT_NGP(x) (((x) & 0xf) << 4)
-#define GPD_EXT_BUF(x) (((x) & 0xf) << 0)
+#define GPD_RX_BUF_LEN(x) (((x) & 0xffff) << 16)
+#define GPD_DATA_LEN(x) ((x) & 0xffff)
+#define GPD_EXT_FLAG_ZLP BIT(29)
+#define GPD_EXT_NGP(x) (((x) & 0xf) << 20)
+#define GPD_EXT_BUF(x) (((x) & 0xf) << 16)
#define HILO_GEN64(hi, lo) (((u64)(hi) << 32) + (lo))
#define HILO_DMA(hi, lo) \
@@ -125,7 +128,7 @@ static void reset_gpd_list(struct mtu3_ep *mep)
struct qmu_gpd *gpd = ring->start;
if (gpd) {
- gpd->flag &= ~GPD_FLAGS_HWO;
+ gpd->dw0_info &= cpu_to_le32(~GPD_FLAGS_HWO);
gpd_ring_init(ring, gpd);
}
}
@@ -215,15 +218,12 @@ static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
struct qmu_gpd *gpd = ring->enqueue;
struct usb_request *req = &mreq->request;
dma_addr_t enq_dma;
- u16 ext_addr;
-
- /* set all fields to zero as default value */
- memset(gpd, 0, sizeof(*gpd));
+ u32 ext_addr;
+ gpd->dw0_info = 0; /* SW own it */
gpd->buffer = cpu_to_le32(lower_32_bits(req->dma));
ext_addr = GPD_EXT_BUF(upper_32_bits(req->dma));
- gpd->buf_len = cpu_to_le16(req->length);
- gpd->flag |= GPD_FLAGS_IOC;
+ gpd->dw3_info = cpu_to_le32(GPD_DATA_LEN(req->length));
/* get the next GPD */
enq = advance_enq_gpd(ring);
@@ -231,15 +231,15 @@ static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
dev_dbg(mep->mtu->dev, "TX-EP%d queue gpd=%p, enq=%p, qdma=%pad\n",
mep->epnum, gpd, enq, &enq_dma);
- enq->flag &= ~GPD_FLAGS_HWO;
+ enq->dw0_info &= cpu_to_le32(~GPD_FLAGS_HWO);
gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(upper_32_bits(enq_dma));
- gpd->tx_ext_addr = cpu_to_le16(ext_addr);
+ gpd->dw0_info = cpu_to_le32(ext_addr);
if (req->zero)
- gpd->ext_flag |= GPD_EXT_FLAG_ZLP;
+ gpd->dw3_info |= cpu_to_le32(GPD_EXT_FLAG_ZLP);
- gpd->flag |= GPD_FLAGS_HWO;
+ gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_IOC | GPD_FLAGS_HWO);
mreq->gpd = gpd;
@@ -253,15 +253,12 @@ static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
struct qmu_gpd *gpd = ring->enqueue;
struct usb_request *req = &mreq->request;
dma_addr_t enq_dma;
- u16 ext_addr;
-
- /* set all fields to zero as default value */
- memset(gpd, 0, sizeof(*gpd));
+ u32 ext_addr;
+ gpd->dw0_info = 0; /* SW own it */
gpd->buffer = cpu_to_le32(lower_32_bits(req->dma));
ext_addr = GPD_EXT_BUF(upper_32_bits(req->dma));
- gpd->data_buf_len = cpu_to_le16(req->length);
- gpd->flag |= GPD_FLAGS_IOC;
+ gpd->dw0_info = cpu_to_le32(GPD_RX_BUF_LEN(req->length));
/* get the next GPD */
enq = advance_enq_gpd(ring);
@@ -269,11 +266,11 @@ static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
dev_dbg(mep->mtu->dev, "RX-EP%d queue gpd=%p, enq=%p, qdma=%pad\n",
mep->epnum, gpd, enq, &enq_dma);
- enq->flag &= ~GPD_FLAGS_HWO;
+ enq->dw0_info &= cpu_to_le32(~GPD_FLAGS_HWO);
gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(upper_32_bits(enq_dma));
- gpd->rx_ext_addr = cpu_to_le16(ext_addr);
- gpd->flag |= GPD_FLAGS_HWO;
+ gpd->dw3_info = cpu_to_le32(ext_addr);
+ gpd->dw0_info |= cpu_to_le32(GPD_FLAGS_IOC | GPD_FLAGS_HWO);
mreq->gpd = gpd;
@@ -394,7 +391,7 @@ static void qmu_tx_zlp_error_handler(struct mtu3 *mtu, u8 epnum)
cur_gpd_dma = read_txq_cur_addr(mbase, epnum);
gpd_current = gpd_dma_to_virt(ring, cur_gpd_dma);
- if (le16_to_cpu(gpd_current->buf_len) != 0) {
+ if (GPD_DATA_LEN(le32_to_cpu(gpd_current->dw3_info)) != 0) {
dev_err(mtu->dev, "TX EP%d buffer length error(!=0)\n", epnum);
return;
}
@@ -412,8 +409,7 @@ static void qmu_tx_zlp_error_handler(struct mtu3 *mtu, u8 epnum)
mtu3_setbits(mbase, MU3D_EP_TXCR0(mep->epnum), TX_TXPKTRDY);
/* by pass the current GDP */
- gpd_current->flag |= GPD_FLAGS_BPS;
- gpd_current->flag |= GPD_FLAGS_HWO;
+ gpd_current->dw0_info |= cpu_to_le32(GPD_FLAGS_BPS | GPD_FLAGS_HWO);
/*enable DMAREQEN, switch back to QMU mode */
mtu3_setbits(mbase, MU3D_EP_TXCR0(mep->epnum), TX_DMAREQEN);
@@ -445,7 +441,7 @@ static void qmu_done_tx(struct mtu3 *mtu, u8 epnum)
dev_dbg(mtu->dev, "%s EP%d, last=%p, current=%p, enq=%p\n",
__func__, epnum, gpd, gpd_current, ring->enqueue);
- while (gpd != gpd_current && !(gpd->flag & GPD_FLAGS_HWO)) {
+ while (gpd != gpd_current && !GET_GPD_HWO(gpd)) {
mreq = next_request(mep);
@@ -455,7 +451,7 @@ static void qmu_done_tx(struct mtu3 *mtu, u8 epnum)
}
request = &mreq->request;
- request->actual = le16_to_cpu(gpd->buf_len);
+ request->actual = GPD_DATA_LEN(le32_to_cpu(gpd->dw3_info));
mtu3_req_complete(mep, request, 0);
gpd = advance_deq_gpd(ring);
@@ -483,7 +479,7 @@ static void qmu_done_rx(struct mtu3 *mtu, u8 epnum)
dev_dbg(mtu->dev, "%s EP%d, last=%p, current=%p, enq=%p\n",
__func__, epnum, gpd, gpd_current, ring->enqueue);
- while (gpd != gpd_current && !(gpd->flag & GPD_FLAGS_HWO)) {
+ while (gpd != gpd_current && !GET_GPD_HWO(gpd)) {
mreq = next_request(mep);
@@ -493,7 +489,7 @@ static void qmu_done_rx(struct mtu3 *mtu, u8 epnum)
}
req = &mreq->request;
- req->actual = le16_to_cpu(gpd->buf_len);
+ req->actual = GPD_DATA_LEN(le32_to_cpu(gpd->dw3_info));
mtu3_req_complete(mep, req, 0);
gpd = advance_deq_gpd(ring);
To support USB3 Gen2 ISOC, the data buffer length need be extended, it's hard to make the current qmu_gpd struct compatible, so here rebuild qmu_gpd struct and make easy to support new QMU format Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- drivers/usb/mtu3/mtu3.h | 45 +++++++++++------------------ drivers/usb/mtu3/mtu3_qmu.c | 56 +++++++++++++++++-------------------- 2 files changed, 42 insertions(+), 59 deletions(-)