diff mbox series

[v5,5/6] usb: roles: add USB Type-B GPIO connector driver

Message ID 1557823643-8616-6-git-send-email-chunfeng.yun@mediatek.com (mailing list archive)
State Superseded
Headers show
Series add USB Type-B GPIO connector driver | expand

Commit Message

Chunfeng Yun May 14, 2019, 8:47 a.m. UTC 
Due to the requirement of usb-connector.txt binding, the old way
using extcon to support USB Dual-Role switch is now deprecated
when use Type-B connector.
This patch introduces a driver of Type-B connector which typically
uses an input GPIO to detect USB ID pin, and try to replace the
function provided by extcon-usb-gpio driver

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v5 changes:
  1. put usb_role_switch when error happens suggested by Biju
  2. don't treat bype-B connector as a virtual device suggested by Rob

v4 changes:
  1. remove linux/gpio.h suggested by Linus
  2. put node when error happens

v3 changes:
  1. treat bype-B connector as a virtual device;
  2. change file name again

v2 changes:
  1. file name is changed
  2. use new compatible
---
 drivers/usb/roles/Kconfig           |  11 ++
 drivers/usb/roles/Makefile          |   1 +
 drivers/usb/roles/typeb-conn-gpio.c | 295 ++++++++++++++++++++++++++++
 3 files changed, 307 insertions(+)
 create mode 100644 drivers/usb/roles/typeb-conn-gpio.c

Comments

Heikki Krogerus May 20, 2019, 8:31 a.m. UTC | #1 
On Tue, May 14, 2019 at 04:47:22PM +0800, Chunfeng Yun wrote:
> +static int usb_conn_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *node = dev->of_node;
> +	struct device_node *remote_node;
> +	struct usb_conn_info *info;
> +	int ret = 0;
> +
> +	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> +	if (!info)
> +		return -ENOMEM;
> +
> +	info->dev = dev;
> +	info->id_gpiod = devm_gpiod_get_optional(dev, "id", GPIOD_IN);
> +	if (IS_ERR(info->id_gpiod))
> +		return PTR_ERR(info->id_gpiod);
> +
> +	info->vbus_gpiod = devm_gpiod_get_optional(dev, "vbus", GPIOD_IN);
> +	if (IS_ERR(info->vbus_gpiod))
> +		return PTR_ERR(info->vbus_gpiod);
> +
> +	if (!info->id_gpiod && !info->vbus_gpiod) {
> +		dev_err(dev, "failed to get gpios\n");
> +		return -ENODEV;
> +	}
> +
> +	if (info->id_gpiod)
> +		ret = gpiod_set_debounce(info->id_gpiod, USB_GPIO_DEB_US);
> +	if (!ret && info->vbus_gpiod)
> +		ret = gpiod_set_debounce(info->vbus_gpiod, USB_GPIO_DEB_US);
> +	if (ret < 0)
> +		info->debounce_jiffies = msecs_to_jiffies(USB_GPIO_DEB_MS);
> +
> +	INIT_DELAYED_WORK(&info->dw_det, usb_conn_detect_cable);
> +
> +	info->vbus = devm_regulator_get(dev, "vbus");
> +	if (IS_ERR(info->vbus)) {
> +		dev_err(dev, "failed to get vbus\n");
> +		return PTR_ERR(info->vbus);
> +	}
> +
> +	remote_node = of_graph_get_remote_node(node, -1, 0);

This is really not ideal. In practice this code will only work if
there is only one endpoint described for this device, or if the first
endpoint is always the one we are looking for. There is no way to
guarantee that.

The code really has to walk through the entire graph, and identify the
remote endpoint it's looking for (and for that we have the boolean
device property).

> +	if (!remote_node) {
> +		dev_err(dev, "failed to get remote node\n");
> +		return -ENODEV;
> +	}
> +
> +	info->role_sw =
> +		fwnode_usb_role_switch_get(of_fwnode_handle(remote_node));

So fwnode_usb_role_switch_get() needs be the one that walks through
the graph, not the drivers. Otherwise every driver will do the same
exact steps (boilerplate). Here you need to be able to just pass the
node of this device, not the remote endpoint:

        info->role_sw = fwnode_usb_role_switch_get(dev_fwnode(&client->dev));

But why do you need that function at all? Why wouldn't
usb_role_switch_get() work?

        info->role_sw = usb_role_switch_get(&client->dev);

> +	of_node_put(remote_node);
> +	if (IS_ERR(info->role_sw)) {
> +		dev_err(dev, "failed to get role switch\n");
> +		return PTR_ERR(info->role_sw);
> +	}
> +
> +	if (info->id_gpiod) {
> +		info->id_irq = gpiod_to_irq(info->id_gpiod);
> +		if (info->id_irq < 0) {
> +			dev_err(dev, "failed to get ID IRQ\n");
> +			ret = info->id_irq;
> +			goto put_role_sw;
> +		}
> +
> +		ret = devm_request_threaded_irq(dev, info->id_irq, NULL,
> +						usb_conn_isr, USB_CONN_IRQF,
> +						pdev->name, info);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to request ID IRQ\n");
> +			goto put_role_sw;
> +		}
> +	}
> +
> +	if (info->vbus_gpiod) {
> +		info->vbus_irq = gpiod_to_irq(info->vbus_gpiod);
> +		if (info->vbus_irq < 0) {
> +			dev_err(dev, "failed to get VBUS IRQ\n");
> +			ret = info->vbus_irq;
> +			goto put_role_sw;
> +		}
> +
> +		ret = devm_request_threaded_irq(dev, info->vbus_irq, NULL,
> +						usb_conn_isr, USB_CONN_IRQF,
> +						pdev->name, info);
> +		if (ret < 0) {
> +			dev_err(dev, "failed to request VBUS IRQ\n");
> +			goto put_role_sw;
> +		}
> +	}
> +
> +	platform_set_drvdata(pdev, info);
> +
> +	/* Perform initial detection */
> +	usb_conn_queue_dwork(info, 0);
> +
> +	return 0;
> +
> +put_role_sw:
> +	usb_role_switch_put(info->role_sw);
> +	return ret;
> +}

thanks,
Chunfeng Yun May 21, 2019, 7:44 a.m. UTC | #2 
Hi,

On Mon, 2019-05-20 at 11:31 +0300, Heikki Krogerus wrote:
> On Tue, May 14, 2019 at 04:47:22PM +0800, Chunfeng Yun wrote:
> > +static int usb_conn_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct device_node *node = dev->of_node;
> > +	struct device_node *remote_node;
> > +	struct usb_conn_info *info;
> > +	int ret = 0;
> > +
> > +	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> > +	if (!info)
> > +		return -ENOMEM;
> > +
> > +	info->dev = dev;
> > +	info->id_gpiod = devm_gpiod_get_optional(dev, "id", GPIOD_IN);
> > +	if (IS_ERR(info->id_gpiod))
> > +		return PTR_ERR(info->id_gpiod);
> > +
> > +	info->vbus_gpiod = devm_gpiod_get_optional(dev, "vbus", GPIOD_IN);
> > +	if (IS_ERR(info->vbus_gpiod))
> > +		return PTR_ERR(info->vbus_gpiod);
> > +
> > +	if (!info->id_gpiod && !info->vbus_gpiod) {
> > +		dev_err(dev, "failed to get gpios\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	if (info->id_gpiod)
> > +		ret = gpiod_set_debounce(info->id_gpiod, USB_GPIO_DEB_US);
> > +	if (!ret && info->vbus_gpiod)
> > +		ret = gpiod_set_debounce(info->vbus_gpiod, USB_GPIO_DEB_US);
> > +	if (ret < 0)
> > +		info->debounce_jiffies = msecs_to_jiffies(USB_GPIO_DEB_MS);
> > +
> > +	INIT_DELAYED_WORK(&info->dw_det, usb_conn_detect_cable);
> > +
> > +	info->vbus = devm_regulator_get(dev, "vbus");
> > +	if (IS_ERR(info->vbus)) {
> > +		dev_err(dev, "failed to get vbus\n");
> > +		return PTR_ERR(info->vbus);
> > +	}
> > +
> > +	remote_node = of_graph_get_remote_node(node, -1, 0);
> 
> This is really not ideal. In practice this code will only work if
> there is only one endpoint described for this device, or if the first
> endpoint is always the one we are looking for. There is no way to
> guarantee that.
Yes, it is.
I'll modify it as case 2, see reply [v5, 4/6] in this series.

> 
> The code really has to walk through the entire graph, and identify the
> remote endpoint it's looking for (and for that we have the boolean
> device property).
> 
> > +	if (!remote_node) {
> > +		dev_err(dev, "failed to get remote node\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	info->role_sw =
> > +		fwnode_usb_role_switch_get(of_fwnode_handle(remote_node));
> 
> So fwnode_usb_role_switch_get() needs be the one that walks through
> the graph, not the drivers. Otherwise every driver will do the same
> exact steps (boilerplate). Here you need to be able to just pass the
> node of this device, not the remote endpoint:
> 
>         info->role_sw = fwnode_usb_role_switch_get(dev_fwnode(&client->dev));
> 
> But why do you need that function at all? Why wouldn't
> usb_role_switch_get() work?
> 
>         info->role_sw = usb_role_switch_get(&client->dev);
> 
see reply [v5, 4/6] in this series

Thanks a lot.

> > +	of_node_put(remote_node);
> > +	if (IS_ERR(info->role_sw)) {
> > +		dev_err(dev, "failed to get role switch\n");
> > +		return PTR_ERR(info->role_sw);
> > +	}
> > +
> > +	if (info->id_gpiod) {
> > +		info->id_irq = gpiod_to_irq(info->id_gpiod);
> > +		if (info->id_irq < 0) {
> > +			dev_err(dev, "failed to get ID IRQ\n");
> > +			ret = info->id_irq;
> > +			goto put_role_sw;
> > +		}
> > +
> > +		ret = devm_request_threaded_irq(dev, info->id_irq, NULL,
> > +						usb_conn_isr, USB_CONN_IRQF,
> > +						pdev->name, info);
> > +		if (ret < 0) {
> > +			dev_err(dev, "failed to request ID IRQ\n");
> > +			goto put_role_sw;
> > +		}
> > +	}
> > +
> > +	if (info->vbus_gpiod) {
> > +		info->vbus_irq = gpiod_to_irq(info->vbus_gpiod);
> > +		if (info->vbus_irq < 0) {
> > +			dev_err(dev, "failed to get VBUS IRQ\n");
> > +			ret = info->vbus_irq;
> > +			goto put_role_sw;
> > +		}
> > +
> > +		ret = devm_request_threaded_irq(dev, info->vbus_irq, NULL,
> > +						usb_conn_isr, USB_CONN_IRQF,
> > +						pdev->name, info);
> > +		if (ret < 0) {
> > +			dev_err(dev, "failed to request VBUS IRQ\n");
> > +			goto put_role_sw;
> > +		}
> > +	}
> > +
> > +	platform_set_drvdata(pdev, info);
> > +
> > +	/* Perform initial detection */
> > +	usb_conn_queue_dwork(info, 0);
> > +
> > +	return 0;
> > +
> > +put_role_sw:
> > +	usb_role_switch_put(info->role_sw);
> > +	return ret;
> > +}
> 
> thanks,
>
diff mbox series

Patch

diff --git a/drivers/usb/roles/Kconfig b/drivers/usb/roles/Kconfig
index f8b31aa67526..d1156e18a81a 100644
--- a/drivers/usb/roles/Kconfig
+++ b/drivers/usb/roles/Kconfig
@@ -26,4 +26,15 @@  config USB_ROLES_INTEL_XHCI
 	  To compile the driver as a module, choose M here: the module will
 	  be called intel-xhci-usb-role-switch.
 
+config TYPEB_CONN_GPIO
+	tristate "USB Type-B GPIO Connector"
+	depends on GPIOLIB
+	help
+	  The driver supports USB role switch between host and device via GPIO
+	  based USB cable detection, used typically if an input GPIO is used
+	  to detect USB ID pin.
+
+	  To compile the driver as a module, choose M here: the module will
+	  be called typeb-conn-gpio.ko
+
 endif # USB_ROLE_SWITCH
diff --git a/drivers/usb/roles/Makefile b/drivers/usb/roles/Makefile
index 757a7d2797eb..5d5620d9d113 100644
--- a/drivers/usb/roles/Makefile
+++ b/drivers/usb/roles/Makefile
@@ -3,3 +3,4 @@ 
 obj-$(CONFIG_USB_ROLE_SWITCH)		+= roles.o
 roles-y					:= class.o
 obj-$(CONFIG_USB_ROLES_INTEL_XHCI)	+= intel-xhci-usb-role-switch.o
+obj-$(CONFIG_TYPEB_CONN_GPIO)		+= typeb-conn-gpio.o
diff --git a/drivers/usb/roles/typeb-conn-gpio.c b/drivers/usb/roles/typeb-conn-gpio.c
new file mode 100644
index 000000000000..988ecf565f33
--- /dev/null
+++ b/drivers/usb/roles/typeb-conn-gpio.c
@@ -0,0 +1,295 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Type-B GPIO Connector Driver
+ *
+ * Copyright (C) 2019 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ *
+ * Some code borrowed from drivers/extcon/extcon-usb-gpio.c
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/role.h>
+
+#define USB_GPIO_DEB_MS		20	/* ms */
+#define USB_GPIO_DEB_US		((USB_GPIO_DEB_MS) * 1000)	/* us */
+
+#define USB_CONN_IRQF	\
+	(IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT)
+
+struct usb_conn_info {
+	struct device *dev;
+	struct usb_role_switch *role_sw;
+	enum usb_role last_role;
+	struct regulator *vbus;
+	struct delayed_work dw_det;
+	unsigned long debounce_jiffies;
+
+	struct gpio_desc *id_gpiod;
+	struct gpio_desc *vbus_gpiod;
+	int id_irq;
+	int vbus_irq;
+};
+
+/**
+ * "DEVICE" = VBUS and "HOST" = !ID, so we have:
+ * Both "DEVICE" and "HOST" can't be set as active at the same time
+ * so if "HOST" is active (i.e. ID is 0)  we keep "DEVICE" inactive
+ * even if VBUS is on.
+ *
+ *  Role          |   ID  |  VBUS
+ * ------------------------------------
+ *  [1] DEVICE    |   H   |   H
+ *  [2] NONE      |   H   |   L
+ *  [3] HOST      |   L   |   H
+ *  [4] HOST      |   L   |   L
+ *
+ * In case we have only one of these signals:
+ * - VBUS only - we want to distinguish between [1] and [2], so ID is always 1
+ * - ID only - we want to distinguish between [1] and [4], so VBUS = ID
+ */
+static void usb_conn_detect_cable(struct work_struct *work)
+{
+	struct usb_conn_info *info;
+	enum usb_role role;
+	int id, vbus, ret;
+
+	info = container_of(to_delayed_work(work),
+			    struct usb_conn_info, dw_det);
+
+	/* check ID and VBUS */
+	id = info->id_gpiod ?
+		gpiod_get_value_cansleep(info->id_gpiod) : 1;
+	vbus = info->vbus_gpiod ?
+		gpiod_get_value_cansleep(info->vbus_gpiod) : id;
+
+	if (!id)
+		role = USB_ROLE_HOST;
+	else if (vbus)
+		role = USB_ROLE_DEVICE;
+	else
+		role = USB_ROLE_NONE;
+
+	dev_dbg(info->dev, "role %d/%d, gpios: id %d, vbus %d\n",
+		info->last_role, role, id, vbus);
+
+	if (info->last_role == role) {
+		dev_warn(info->dev, "repeated role: %d\n", role);
+		return;
+	}
+
+	if (info->last_role == USB_ROLE_HOST)
+		regulator_disable(info->vbus);
+
+	ret = usb_role_switch_set_role(info->role_sw, role);
+	if (ret)
+		dev_err(info->dev, "failed to set role: %d\n", ret);
+
+	if (role == USB_ROLE_HOST) {
+		ret = regulator_enable(info->vbus);
+		if (ret)
+			dev_err(info->dev, "enable vbus regulator failed\n");
+	}
+
+	info->last_role = role;
+
+	dev_dbg(info->dev, "vbus regulator is %s\n",
+		regulator_is_enabled(info->vbus) ? "enabled" : "disabled");
+}
+
+static void usb_conn_queue_dwork(struct usb_conn_info *info,
+				 unsigned long delay)
+{
+	queue_delayed_work(system_power_efficient_wq, &info->dw_det, delay);
+}
+
+static irqreturn_t usb_conn_isr(int irq, void *dev_id)
+{
+	struct usb_conn_info *info = dev_id;
+
+	usb_conn_queue_dwork(info, info->debounce_jiffies);
+
+	return IRQ_HANDLED;
+}
+
+static int usb_conn_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct device_node *remote_node;
+	struct usb_conn_info *info;
+	int ret = 0;
+
+	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->dev = dev;
+	info->id_gpiod = devm_gpiod_get_optional(dev, "id", GPIOD_IN);
+	if (IS_ERR(info->id_gpiod))
+		return PTR_ERR(info->id_gpiod);
+
+	info->vbus_gpiod = devm_gpiod_get_optional(dev, "vbus", GPIOD_IN);
+	if (IS_ERR(info->vbus_gpiod))
+		return PTR_ERR(info->vbus_gpiod);
+
+	if (!info->id_gpiod && !info->vbus_gpiod) {
+		dev_err(dev, "failed to get gpios\n");
+		return -ENODEV;
+	}
+
+	if (info->id_gpiod)
+		ret = gpiod_set_debounce(info->id_gpiod, USB_GPIO_DEB_US);
+	if (!ret && info->vbus_gpiod)
+		ret = gpiod_set_debounce(info->vbus_gpiod, USB_GPIO_DEB_US);
+	if (ret < 0)
+		info->debounce_jiffies = msecs_to_jiffies(USB_GPIO_DEB_MS);
+
+	INIT_DELAYED_WORK(&info->dw_det, usb_conn_detect_cable);
+
+	info->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(info->vbus)) {
+		dev_err(dev, "failed to get vbus\n");
+		return PTR_ERR(info->vbus);
+	}
+
+	remote_node = of_graph_get_remote_node(node, -1, 0);
+	if (!remote_node) {
+		dev_err(dev, "failed to get remote node\n");
+		return -ENODEV;
+	}
+
+	info->role_sw =
+		fwnode_usb_role_switch_get(of_fwnode_handle(remote_node));
+	of_node_put(remote_node);
+	if (IS_ERR(info->role_sw)) {
+		dev_err(dev, "failed to get role switch\n");
+		return PTR_ERR(info->role_sw);
+	}
+
+	if (info->id_gpiod) {
+		info->id_irq = gpiod_to_irq(info->id_gpiod);
+		if (info->id_irq < 0) {
+			dev_err(dev, "failed to get ID IRQ\n");
+			ret = info->id_irq;
+			goto put_role_sw;
+		}
+
+		ret = devm_request_threaded_irq(dev, info->id_irq, NULL,
+						usb_conn_isr, USB_CONN_IRQF,
+						pdev->name, info);
+		if (ret < 0) {
+			dev_err(dev, "failed to request ID IRQ\n");
+			goto put_role_sw;
+		}
+	}
+
+	if (info->vbus_gpiod) {
+		info->vbus_irq = gpiod_to_irq(info->vbus_gpiod);
+		if (info->vbus_irq < 0) {
+			dev_err(dev, "failed to get VBUS IRQ\n");
+			ret = info->vbus_irq;
+			goto put_role_sw;
+		}
+
+		ret = devm_request_threaded_irq(dev, info->vbus_irq, NULL,
+						usb_conn_isr, USB_CONN_IRQF,
+						pdev->name, info);
+		if (ret < 0) {
+			dev_err(dev, "failed to request VBUS IRQ\n");
+			goto put_role_sw;
+		}
+	}
+
+	platform_set_drvdata(pdev, info);
+
+	/* Perform initial detection */
+	usb_conn_queue_dwork(info, 0);
+
+	return 0;
+
+put_role_sw:
+	usb_role_switch_put(info->role_sw);
+	return ret;
+}
+
+static int usb_conn_remove(struct platform_device *pdev)
+{
+	struct usb_conn_info *info = platform_get_drvdata(pdev);
+
+	cancel_delayed_work_sync(&info->dw_det);
+
+	if (info->last_role == USB_ROLE_HOST)
+		regulator_disable(info->vbus);
+
+	usb_role_switch_put(info->role_sw);
+
+	return 0;
+}
+
+static int __maybe_unused usb_conn_suspend(struct device *dev)
+{
+	struct usb_conn_info *info = dev_get_drvdata(dev);
+
+	if (info->id_gpiod)
+		disable_irq(info->id_irq);
+	if (info->vbus_gpiod)
+		disable_irq(info->vbus_irq);
+
+	pinctrl_pm_select_sleep_state(dev);
+
+	return 0;
+}
+
+static int __maybe_unused usb_conn_resume(struct device *dev)
+{
+	struct usb_conn_info *info = dev_get_drvdata(dev);
+
+	pinctrl_pm_select_default_state(dev);
+
+	if (info->id_gpiod)
+		enable_irq(info->id_irq);
+	if (info->vbus_gpiod)
+		enable_irq(info->vbus_irq);
+
+	usb_conn_queue_dwork(info, 0);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(usb_conn_pm_ops,
+			 usb_conn_suspend, usb_conn_resume);
+
+#define DEV_PMS_OPS (IS_ENABLED(CONFIG_PM_SLEEP) ? &usb_conn_pm_ops : NULL)
+
+static const struct of_device_id usb_conn_dt_match[] = {
+	{ .compatible = "linux,typeb-conn-gpio", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, usb_conn_dt_match);
+
+static struct platform_driver usb_conn_driver = {
+	.probe		= usb_conn_probe,
+	.remove		= usb_conn_remove,
+	.driver		= {
+		.name	= "typeb-conn-gpio",
+		.pm	= DEV_PMS_OPS,
+		.of_match_table = usb_conn_dt_match,
+	},
+};
+
+module_platform_driver(usb_conn_driver);
+
+MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
+MODULE_DESCRIPTION("USB Type-B GPIO connector driver");
+MODULE_LICENSE("GPL v2");