| Message ID | 20200829090539.80140-1-aleksander@aleksander.es (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | 1ac698790819b83f39fd7ea4f6cdabee9bdd7b38 |
| Headers | show |
| Series | USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules | expand |
On Sat, Aug 29, 2020 at 11:05:39AM +0200, Aleksander Morgado wrote: > These modules have 2 different USB layouts: > > The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and > an ECM interface: > > T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 > P: Vendor=1e0e ProdID=9205 Rev=00.00 > S: Manufacturer=SimTech, Incorporated > S: Product=SimTech SIM7080 > S: SerialNumber=1234567890ABCDEF > C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA > I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether > I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether > > The purpose of each TTY is as follows: > * ttyUSB0: DIAG/QCDM port. > * ttyUSB1: GNSS data. > * ttyUSB2: AT-capable port (control). > * ttyUSB3: AT-capable port (data). > > In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module > exposes 6 TTY ports: > > T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 > P: Vendor=1e0e ProdID=9206 Rev=00.00 > S: Manufacturer=SimTech, Incorporated > S: Product=SimTech SIM7080 > S: SerialNumber=1234567890ABCDEF > C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA > I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option > > The purpose of each TTY is as follows: > * ttyUSB0: DIAG/QCDM port. > * ttyUSB1: GNSS data. > * ttyUSB2: AT-capable port (control). > * ttyUSB3: QFLOG interface. > * ttyUSB4: DAM interface. > * ttyUSB5: AT-capable port (data). > > Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Now applied. Thanks, Aleksander. Johan
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 89b3192af326..01c5b452c6ea 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -1819,6 +1819,8 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_INTERFACE_CLASS(0x1e0e, 0x9003, 0xff) }, /* Simcom SIM7500/SIM7600 MBIM mode */ { USB_DEVICE_INTERFACE_CLASS(0x1e0e, 0x9011, 0xff), /* Simcom SIM7500/SIM7600 RNDIS mode */ .driver_info = RSVD(7) }, + { USB_DEVICE_INTERFACE_CLASS(0x1e0e, 0x9205, 0xff) }, /* Simcom SIM7070/SIM7080/SIM7090 AT+ECM mode */ + { USB_DEVICE_INTERFACE_CLASS(0x1e0e, 0x9206, 0xff) }, /* Simcom SIM7070/SIM7080/SIM7090 AT-only mode */ { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X060S_X200), .driver_info = NCTRL(0) | NCTRL(1) | RSVD(4) }, { USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X220_X500D),
These modules have 2 different USB layouts: The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and an ECM interface: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9205 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: AT-capable port (data). In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module exposes 6 TTY ports: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9206 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: QFLOG interface. * ttyUSB4: DAM interface. * ttyUSB5: AT-capable port (data). Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> --- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+)