Message ID | 20201118082126.42701-10-chunfeng.yun@mediatek.com (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | [v3,01/11] dt-bindings: usb: convert usb-device.txt to YAML schema | expand |
On Wed, Nov 18, 2020 at 04:21:25PM +0800, Chunfeng Yun wrote: > Convert mediatek,mtu3.txt to YAML schema mediatek,mtu3.yaml > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > --- > v3: > 1. fix yamllint warning > 2. remove pinctrl* properties > 3. remove unnecessary '|' > 4. drop unused labels in example > > v2: new patch > --- > .../devicetree/bindings/usb/mediatek,mtu3.txt | 108 --------- > .../bindings/usb/mediatek,mtu3.yaml | 218 ++++++++++++++++++ > 2 files changed, 218 insertions(+), 108 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.txt > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt > deleted file mode 100644 > index a82ca438aec1..000000000000 > --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt > +++ /dev/null > @@ -1,108 +0,0 @@ > -The device node for Mediatek USB3.0 DRD controller > - > -Required properties: > - - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3", > - soc-model is the name of SoC, such as mt8173, mt2712 etc, > - when using "mediatek,mtu3" compatible string, you need SoC specific > - ones in addition, one of: > - - "mediatek,mt8173-mtu3" > - - reg : specifies physical base address and size of the registers > - - reg-names: should be "mac" for device IP and "ippc" for IP port control > - - interrupts : interrupt used by the device IP > - - power-domains : a phandle to USB power domain node to control USB's > - mtcmos > - - vusb33-supply : regulator of USB avdd3.3v > - - clocks : a list of phandle + clock-specifier pairs, one for each > - entry in clock-names > - - clock-names : must contain "sys_ck" for clock of controller, > - the following clocks are optional: > - "ref_ck", "mcu_ck" and "dma_ck"; > - - phys : see usb-hcd.yaml in the current directory > - - dr_mode : should be one of "host", "peripheral" or "otg", > - refer to usb/generic.txt > - > -Optional properties: > - - #address-cells, #size-cells : should be '2' if the device has sub-nodes > - with 'reg' property > - - ranges : allows valid 1:1 translation between child's address space and > - parent's address space > - - extcon : external connector for vbus and idpin changes detection, needed > - when supports dual-role mode. > - it's considered valid for compatibility reasons, not allowed for > - new bindings, and use "usb-role-switch" property instead. > - - vbus-supply : reference to the VBUS regulator, needed when supports > - dual-role mode. > - it's considered valid for compatibility reasons, not allowed for > - new bindings, and put into a usb-connector node. > - see connector/usb-connector.yaml. > - - pinctrl-names : a pinctrl state named "default" is optional, and need be > - defined if auto drd switch is enabled, that means the property dr_mode > - is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" > - is not set. > - - pinctrl-0 : pin control group > - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt > - > - - maximum-speed : valid arguments are "super-speed", "high-speed" and > - "full-speed"; refer to usb/generic.txt > - - usb-role-switch : use USB Role Switch to support dual-role switch, but > - not extcon; see usb/generic.txt. > - - enable-manual-drd : supports manual dual-role switch via debugfs; usually > - used when receptacle is TYPE-A and also wants to support dual-role > - mode. > - - wakeup-source: enable USB remote wakeup of host mode. > - - mediatek,syscon-wakeup : phandle to syscon used to access the register > - of the USB wakeup glue layer between SSUSB and SPM; it depends on > - "wakeup-source", and has two arguments: > - - the first one : register base address of the glue layer in syscon; > - - the second one : hardware version of the glue layer > - - 1 : used by mt8173 etc > - - 2 : used by mt2712 etc > - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, > - bit1 for u3port1, ... etc; > - > -additionally the properties from usb-hcd.yaml (in the current directory) are > -supported. > - > -Sub-nodes: > -The xhci should be added as subnode to mtu3 as shown in the following example > -if host mode is enabled. The DT binding details of xhci can be found in: > -Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt > - > -The port would be added as subnode if use "usb-role-switch" property. > - see graph.txt > - > -Example: > -ssusb: usb@11271000 { > - compatible = "mediatek,mt8173-mtu3"; > - reg = <0 0x11271000 0 0x3000>, > - <0 0x11280700 0 0x0100>; > - reg-names = "mac", "ippc"; > - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; > - phys = <&phy_port0 PHY_TYPE_USB3>, > - <&phy_port1 PHY_TYPE_USB2>; > - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, > - <&pericfg CLK_PERI_USB0>, > - <&pericfg CLK_PERI_USB1>; > - clock-names = "sys_ck", "ref_ck"; > - vusb33-supply = <&mt6397_vusb_reg>; > - vbus-supply = <&usb_p0_vbus>; > - extcon = <&extcon_usb>; > - dr_mode = "otg"; > - wakeup-source; > - mediatek,syscon-wakeup = <&pericfg 0x400 1>; > - #address-cells = <2>; > - #size-cells = <2>; > - ranges; > - > - usb_host: xhci@11270000 { > - compatible = "mediatek,mt8173-xhci"; > - reg = <0 0x11270000 0 0x1000>; > - reg-names = "mac"; > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > - clock-names = "sys_ck", "ref_ck"; > - vusb33-supply = <&mt6397_vusb_reg>; > - }; > -}; > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > new file mode 100644 > index 000000000000..290e97a06f2a > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > @@ -0,0 +1,218 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright (c) 2020 MediaTek > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: MediaTek USB3 DRD Controller Device Tree Bindings > + > +maintainers: > + - Chunfeng Yun <chunfeng.yun@mediatek.com> > + > +description: | > + The DRD controller has a glue layer IPPC (IP Port Control), and its host is > + based on xHCI. > + > +properties: > + compatible: > + items: > + - enum: > + - mediatek,mt2712-mtu3 > + - mediatek,mt8173-mtu3 > + - mediatek,mt8183-mtu3 > + - const: mediatek,mtu3 > + > + reg: > + items: > + - description: the registers of device MAC > + - description: the registers of IP Port Control > + > + reg-names: > + items: > + - const: mac > + - const: ippc > + > + interrupts: > + maxItems: 1 > + > + power-domains: > + description: A phandle to USB power domain node to control USB's MTCMOS > + maxItems: 1 > + > + clocks: > + minItems: 1 > + maxItems: 4 > + items: > + - description: Controller clock used by normal mode > + - description: Reference clock used by low power mode etc > + - description: Mcu bus clock for register access > + - description: DMA bus clock for data transfer > + > + clock-names: > + minItems: 1 > + maxItems: 4 > + items: > + - const: sys_ck # required, the following ones are optional > + - const: ref_ck > + - const: mcu_ck > + - const: dma_ck > + > + phys: > + $ref: /schemas/types.yaml#/definitions/phandle-array Drop. Need to say how many entries and what each one is if more than 1. > + description: List of all the USB PHYs used > + > + vusb33-supply: > + description: Regulator of USB AVDD3.3v > + > + vbus-supply: > + $ref: /connector/usb-connector.yaml# Nope. > + deprecated: true > + description: | > + Regulator of USB VBUS5v, needed when supports dual-role mode. > + Particularly, if use an output GPIO to control a VBUS regulator, should > + model it as a regulator. See bindings/regulator/fixed-regulator.yaml > + It's considered valid for compatibility reasons, not allowed for > + new bindings, and put into a usb-connector node. > + > + dr_mode: > + description: See usb/generic.txt > + enum: [host, peripheral, otg] > + default: otg > + > + maximum-speed: > + description: See usb/generic.txt > + enum: [super-speed-plus, super-speed, high-speed, full-speed] > + > + "#address-cells": > + enum: [1, 2] > + > + "#size-cells": > + enum: [1, 2] > + > + ranges: true > + > + extcon: > + deprecated: true > + description: | > + Phandle to the extcon device detecting the IDDIG/VBUS state, neede > + when supports dual-role mode. > + It's considered valid for compatibility reasons, not allowed for > + new bindings, and use "usb-role-switch" property instead. > + > + usb-role-switch: > + $ref: /schemas/types.yaml#/definitions/flag > + description: Support role switch. See usb/generic.txt > + type: boolean > + > + connector: > + $ref: /connector/usb-connector.yaml# > + description: > + Connector for dual role switch, especially for "gpio-usb-b-connector" > + type: object > + > + port: > + description: > + Any connector to the data bus of this controller should be modelled > + using the OF graph bindings specified, if the "usb-role-switch" > + property is used. See graph.txt > + type: object Please include port and connector in the example. > + > + enable-manual-drd: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + supports manual dual-role switch via debugfs; usually used when > + receptacle is TYPE-A and also wants to support dual-role mode. > + type: boolean > + > + wakeup-source: > + description: enable USB remote wakeup, see power/wakeup-source.txt > + type: boolean > + > + mediatek,syscon-wakeup: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + maxItems: 1 > + description: | > + A phandle to syscon used to access the register of the USB wakeup glue > + layer between xHCI and SPM, the field should always be 3 cells long. > + > + items: > + - description: > + The first cell represents a phandle to syscon > + - description: > + The second cell represents the register base address of the glue > + layer in syscon > + - description: > + The third cell represents the hardware version of the glue layer, > + 1 is used by mt8173 etc, 2 is used by mt2712 etc > + enum: [1, 2] > + > + mediatek,u3p-dis-msk: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: The mask to disable u3ports, bit0 for u3port0, > + bit1 for u3port1, ... etc > + > +# Required child node when support dual-role > +patternProperties: > + "^usb@[0-9a-f]+$": > + type: object > + $ref: /usb/mediatek,mtk-xhci.yaml# > + description: > + The xhci should be added as subnode to mtu3 as shown in the following > + example if the host mode is enabled. > + > +dependencies: > + connector: [ 'usb-role-switch' ] > + port: [ 'usb-role-switch' ] > + wakeup-source: [ 'mediatek,syscon-wakeup' ] > + > +required: > + - compatible > + - reg > + - reg-names > + - interrupts > + - clocks > + - clock-names > + - phys > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/mt8173-clk.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + #include <dt-bindings/phy/phy.h> > + #include <dt-bindings/power/mt8173-power.h> > + > + usb@11271000 { > + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; > + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; > + reg-names = "mac", "ippc"; > + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; > + phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > + clocks = <&topckgen CLK_TOP_USB30_SEL>; > + clock-names = "sys_ck"; > + vusb33-supply = <&mt6397_vusb_reg>; > + vbus-supply = <&usb_p0_vbus>; > + extcon = <&extcon_usb>; > + dr_mode = "otg"; > + wakeup-source; > + mediatek,syscon-wakeup = <&pericfg 0x400 1>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + xhci: usb@11270000 { > + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; > + reg = <0x11270000 0x1000>; > + reg-names = "mac"; > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > + clock-names = "sys_ck", "ref_ck"; > + vusb33-supply = <&mt6397_vusb_reg>; > + }; Please add > + }; > +... > -- > 2.18.0 >
On Mon, 2020-12-07 at 15:30 -0600, Rob Herring wrote: > On Wed, Nov 18, 2020 at 04:21:25PM +0800, Chunfeng Yun wrote: > > Convert mediatek,mtu3.txt to YAML schema mediatek,mtu3.yaml > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > --- > > v3: > > 1. fix yamllint warning > > 2. remove pinctrl* properties > > 3. remove unnecessary '|' > > 4. drop unused labels in example > > > > v2: new patch > > --- > > .../devicetree/bindings/usb/mediatek,mtu3.txt | 108 --------- > > .../bindings/usb/mediatek,mtu3.yaml | 218 ++++++++++++++++++ > > 2 files changed, 218 insertions(+), 108 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.txt > > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > > [...] > > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > > new file mode 100644 > > index 000000000000..290e97a06f2a > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml > > @@ -0,0 +1,218 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +# Copyright (c) 2020 MediaTek > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: MediaTek USB3 DRD Controller Device Tree Bindings > > + > > +maintainers: > > + - Chunfeng Yun <chunfeng.yun@mediatek.com> > > + > > +description: | > > + The DRD controller has a glue layer IPPC (IP Port Control), and its host is > > + based on xHCI. > > + > > +properties: > > + compatible: > > + items: > > + - enum: > > + - mediatek,mt2712-mtu3 > > + - mediatek,mt8173-mtu3 > > + - mediatek,mt8183-mtu3 > > + - const: mediatek,mtu3 > > + > > + reg: > > + items: > > + - description: the registers of device MAC > > + - description: the registers of IP Port Control > > + > > + reg-names: > > + items: > > + - const: mac > > + - const: ippc > > + > > + interrupts: > > + maxItems: 1 > > + > > + power-domains: > > + description: A phandle to USB power domain node to control USB's MTCMOS > > + maxItems: 1 > > + > > + clocks: > > + minItems: 1 > > + maxItems: 4 > > + items: > > + - description: Controller clock used by normal mode > > + - description: Reference clock used by low power mode etc > > + - description: Mcu bus clock for register access > > + - description: DMA bus clock for data transfer > > + > > + clock-names: > > + minItems: 1 > > + maxItems: 4 > > + items: > > + - const: sys_ck # required, the following ones are optional > > + - const: ref_ck > > + - const: mcu_ck > > + - const: dma_ck > > + > > + phys: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > Drop. Need to say how many entries and what each one is if more than 1. Ok > > > + description: List of all the USB PHYs used > > + > > + vusb33-supply: > > + description: Regulator of USB AVDD3.3v > > + > > + vbus-supply: > > + $ref: /connector/usb-connector.yaml# > > Nope. Will remove it > > > + deprecated: true > > + description: | > > + Regulator of USB VBUS5v, needed when supports dual-role mode. > > + Particularly, if use an output GPIO to control a VBUS regulator, should > > + model it as a regulator. See bindings/regulator/fixed-regulator.yaml > > + It's considered valid for compatibility reasons, not allowed for > > + new bindings, and put into a usb-connector node. > > + > > + dr_mode: > > + description: See usb/generic.txt > > + enum: [host, peripheral, otg] > > + default: otg > > + > > + maximum-speed: > > + description: See usb/generic.txt > > + enum: [super-speed-plus, super-speed, high-speed, full-speed] > > + > > + "#address-cells": > > + enum: [1, 2] > > + > > + "#size-cells": > > + enum: [1, 2] > > + > > + ranges: true > > + > > + extcon: > > + deprecated: true > > + description: | > > + Phandle to the extcon device detecting the IDDIG/VBUS state, neede > > + when supports dual-role mode. > > + It's considered valid for compatibility reasons, not allowed for > > + new bindings, and use "usb-role-switch" property instead. > > + > > + usb-role-switch: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: Support role switch. See usb/generic.txt > > + type: boolean > > + > > + connector: > > + $ref: /connector/usb-connector.yaml# > > + description: > > + Connector for dual role switch, especially for "gpio-usb-b-connector" > > + type: object > > + > > + port: > > + description: > > + Any connector to the data bus of this controller should be modelled > > + using the OF graph bindings specified, if the "usb-role-switch" > > + property is used. See graph.txt > > + type: object > > Please include port and connector in the example. Ok, thanks > > > + > > + enable-manual-drd: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + supports manual dual-role switch via debugfs; usually used when > > + receptacle is TYPE-A and also wants to support dual-role mode. > > + type: boolean > > + > > + wakeup-source: > > + description: enable USB remote wakeup, see power/wakeup-source.txt > > + type: boolean > > + > > + mediatek,syscon-wakeup: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + maxItems: 1 > > + description: | > > + A phandle to syscon used to access the register of the USB wakeup glue > > + layer between xHCI and SPM, the field should always be 3 cells long. > > + > > + items: > > + - description: > > + The first cell represents a phandle to syscon > > + - description: > > + The second cell represents the register base address of the glue > > + layer in syscon > > + - description: > > + The third cell represents the hardware version of the glue layer, > > + 1 is used by mt8173 etc, 2 is used by mt2712 etc > > + enum: [1, 2] > > + > > + mediatek,u3p-dis-msk: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: The mask to disable u3ports, bit0 for u3port0, > > + bit1 for u3port1, ... etc > > + > > +# Required child node when support dual-role > > +patternProperties: > > + "^usb@[0-9a-f]+$": > > + type: object > > + $ref: /usb/mediatek,mtk-xhci.yaml# > > + description: > > + The xhci should be added as subnode to mtu3 as shown in the following > > + example if the host mode is enabled. > > + > > +dependencies: > > + connector: [ 'usb-role-switch' ] > > + port: [ 'usb-role-switch' ] > > + wakeup-source: [ 'mediatek,syscon-wakeup' ] > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + - interrupts > > + - clocks > > + - clock-names > > + - phys > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/clock/mt8173-clk.h> > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/interrupt-controller/irq.h> > > + #include <dt-bindings/phy/phy.h> > > + #include <dt-bindings/power/mt8173-power.h> > > + > > + usb@11271000 { > > + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; > > + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; > > + reg-names = "mac", "ippc"; > > + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; > > + phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; > > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>; > > + clock-names = "sys_ck"; > > + vusb33-supply = <&mt6397_vusb_reg>; > > + vbus-supply = <&usb_p0_vbus>; > > + extcon = <&extcon_usb>; > > + dr_mode = "otg"; > > + wakeup-source; > > + mediatek,syscon-wakeup = <&pericfg 0x400 1>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + xhci: usb@11270000 { > > + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; > > + reg = <0x11270000 0x1000>; > > + reg-names = "mac"; > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > > + clock-names = "sys_ck", "ref_ck"; > > + vusb33-supply = <&mt6397_vusb_reg>; > > + }; > > Please add > > + }; > > +... > > -- > > 2.18.0 > >
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt deleted file mode 100644 index a82ca438aec1..000000000000 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt +++ /dev/null @@ -1,108 +0,0 @@ -The device node for Mediatek USB3.0 DRD controller - -Required properties: - - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3", - soc-model is the name of SoC, such as mt8173, mt2712 etc, - when using "mediatek,mtu3" compatible string, you need SoC specific - ones in addition, one of: - - "mediatek,mt8173-mtu3" - - reg : specifies physical base address and size of the registers - - reg-names: should be "mac" for device IP and "ippc" for IP port control - - interrupts : interrupt used by the device IP - - power-domains : a phandle to USB power domain node to control USB's - mtcmos - - vusb33-supply : regulator of USB avdd3.3v - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain "sys_ck" for clock of controller, - the following clocks are optional: - "ref_ck", "mcu_ck" and "dma_ck"; - - phys : see usb-hcd.yaml in the current directory - - dr_mode : should be one of "host", "peripheral" or "otg", - refer to usb/generic.txt - -Optional properties: - - #address-cells, #size-cells : should be '2' if the device has sub-nodes - with 'reg' property - - ranges : allows valid 1:1 translation between child's address space and - parent's address space - - extcon : external connector for vbus and idpin changes detection, needed - when supports dual-role mode. - it's considered valid for compatibility reasons, not allowed for - new bindings, and use "usb-role-switch" property instead. - - vbus-supply : reference to the VBUS regulator, needed when supports - dual-role mode. - it's considered valid for compatibility reasons, not allowed for - new bindings, and put into a usb-connector node. - see connector/usb-connector.yaml. - - pinctrl-names : a pinctrl state named "default" is optional, and need be - defined if auto drd switch is enabled, that means the property dr_mode - is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" - is not set. - - pinctrl-0 : pin control group - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - - - maximum-speed : valid arguments are "super-speed", "high-speed" and - "full-speed"; refer to usb/generic.txt - - usb-role-switch : use USB Role Switch to support dual-role switch, but - not extcon; see usb/generic.txt. - - enable-manual-drd : supports manual dual-role switch via debugfs; usually - used when receptacle is TYPE-A and also wants to support dual-role - mode. - - wakeup-source: enable USB remote wakeup of host mode. - - mediatek,syscon-wakeup : phandle to syscon used to access the register - of the USB wakeup glue layer between SSUSB and SPM; it depends on - "wakeup-source", and has two arguments: - - the first one : register base address of the glue layer in syscon; - - the second one : hardware version of the glue layer - - 1 : used by mt8173 etc - - 2 : used by mt2712 etc - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, - bit1 for u3port1, ... etc; - -additionally the properties from usb-hcd.yaml (in the current directory) are -supported. - -Sub-nodes: -The xhci should be added as subnode to mtu3 as shown in the following example -if host mode is enabled. The DT binding details of xhci can be found in: -Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt - -The port would be added as subnode if use "usb-role-switch" property. - see graph.txt - -Example: -ssusb: usb@11271000 { - compatible = "mediatek,mt8173-mtu3"; - reg = <0 0x11271000 0 0x3000>, - <0 0x11280700 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; - phys = <&phy_port0 PHY_TYPE_USB3>, - <&phy_port1 PHY_TYPE_USB2>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, - <&pericfg CLK_PERI_USB0>, - <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck"; - vusb33-supply = <&mt6397_vusb_reg>; - vbus-supply = <&usb_p0_vbus>; - extcon = <&extcon_usb>; - dr_mode = "otg"; - wakeup-source; - mediatek,syscon-wakeup = <&pericfg 0x400 1>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - usb_host: xhci@11270000 { - compatible = "mediatek,mt8173-xhci"; - reg = <0 0x11270000 0 0x1000>; - reg-names = "mac"; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; - clock-names = "sys_ck", "ref_ck"; - vusb33-supply = <&mt6397_vusb_reg>; - }; -}; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml new file mode 100644 index 000000000000..290e97a06f2a --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml @@ -0,0 +1,218 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek USB3 DRD Controller Device Tree Bindings + +maintainers: + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: | + The DRD controller has a glue layer IPPC (IP Port Control), and its host is + based on xHCI. + +properties: + compatible: + items: + - enum: + - mediatek,mt2712-mtu3 + - mediatek,mt8173-mtu3 + - mediatek,mt8183-mtu3 + - const: mediatek,mtu3 + + reg: + items: + - description: the registers of device MAC + - description: the registers of IP Port Control + + reg-names: + items: + - const: mac + - const: ippc + + interrupts: + maxItems: 1 + + power-domains: + description: A phandle to USB power domain node to control USB's MTCMOS + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 4 + items: + - description: Controller clock used by normal mode + - description: Reference clock used by low power mode etc + - description: Mcu bus clock for register access + - description: DMA bus clock for data transfer + + clock-names: + minItems: 1 + maxItems: 4 + items: + - const: sys_ck # required, the following ones are optional + - const: ref_ck + - const: mcu_ck + - const: dma_ck + + phys: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: List of all the USB PHYs used + + vusb33-supply: + description: Regulator of USB AVDD3.3v + + vbus-supply: + $ref: /connector/usb-connector.yaml# + deprecated: true + description: | + Regulator of USB VBUS5v, needed when supports dual-role mode. + Particularly, if use an output GPIO to control a VBUS regulator, should + model it as a regulator. See bindings/regulator/fixed-regulator.yaml + It's considered valid for compatibility reasons, not allowed for + new bindings, and put into a usb-connector node. + + dr_mode: + description: See usb/generic.txt + enum: [host, peripheral, otg] + default: otg + + maximum-speed: + description: See usb/generic.txt + enum: [super-speed-plus, super-speed, high-speed, full-speed] + + "#address-cells": + enum: [1, 2] + + "#size-cells": + enum: [1, 2] + + ranges: true + + extcon: + deprecated: true + description: | + Phandle to the extcon device detecting the IDDIG/VBUS state, neede + when supports dual-role mode. + It's considered valid for compatibility reasons, not allowed for + new bindings, and use "usb-role-switch" property instead. + + usb-role-switch: + $ref: /schemas/types.yaml#/definitions/flag + description: Support role switch. See usb/generic.txt + type: boolean + + connector: + $ref: /connector/usb-connector.yaml# + description: + Connector for dual role switch, especially for "gpio-usb-b-connector" + type: object + + port: + description: + Any connector to the data bus of this controller should be modelled + using the OF graph bindings specified, if the "usb-role-switch" + property is used. See graph.txt + type: object + + enable-manual-drd: + $ref: /schemas/types.yaml#/definitions/flag + description: + supports manual dual-role switch via debugfs; usually used when + receptacle is TYPE-A and also wants to support dual-role mode. + type: boolean + + wakeup-source: + description: enable USB remote wakeup, see power/wakeup-source.txt + type: boolean + + mediatek,syscon-wakeup: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: | + A phandle to syscon used to access the register of the USB wakeup glue + layer between xHCI and SPM, the field should always be 3 cells long. + + items: + - description: + The first cell represents a phandle to syscon + - description: + The second cell represents the register base address of the glue + layer in syscon + - description: + The third cell represents the hardware version of the glue layer, + 1 is used by mt8173 etc, 2 is used by mt2712 etc + enum: [1, 2] + + mediatek,u3p-dis-msk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc + +# Required child node when support dual-role +patternProperties: + "^usb@[0-9a-f]+$": + type: object + $ref: /usb/mediatek,mtk-xhci.yaml# + description: + The xhci should be added as subnode to mtu3 as shown in the following + example if the host mode is enabled. + +dependencies: + connector: [ 'usb-role-switch' ] + port: [ 'usb-role-switch' ] + wakeup-source: [ 'mediatek,syscon-wakeup' ] + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + - phys + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/phy/phy.h> + #include <dt-bindings/power/mt8173-power.h> + + usb@11271000 { + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; + phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p0_vbus>; + extcon = <&extcon_usb>; + dr_mode = "otg"; + wakeup-source; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + xhci: usb@11270000 { + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; + reg = <0x11270000 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + }; + }; +...
Convert mediatek,mtu3.txt to YAML schema mediatek,mtu3.yaml Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- v3: 1. fix yamllint warning 2. remove pinctrl* properties 3. remove unnecessary '|' 4. drop unused labels in example v2: new patch --- .../devicetree/bindings/usb/mediatek,mtu3.txt | 108 --------- .../bindings/usb/mediatek,mtu3.yaml | 218 ++++++++++++++++++ 2 files changed, 218 insertions(+), 108 deletions(-) delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.txt create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml