| Message ID | 20201118082126.42701-9-chunfeng.yun@mediatek.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v3,01/11] dt-bindings: usb: convert usb-device.txt to YAML schema | expand |
On Wed, Nov 18, 2020 at 04:21:24PM +0800, Chunfeng Yun wrote: > Convert mediatek,mtk-xhci.txt to YAML schema mediatek,mtk-xhci.yaml > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > --- > v3: > 1. fix yamllint warning > 2. remove pinctrl* properties supported by default suggested by Rob > 3. drop unused labels > 4. modify description of mediatek,syscon-wakeup > 5. remove type of imod-interval-ns > > v2: new patch > --- > .../bindings/usb/mediatek,mtk-xhci.txt | 121 ------------- > .../bindings/usb/mediatek,mtk-xhci.yaml | 171 ++++++++++++++++++ > 2 files changed, 171 insertions(+), 121 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml > > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt > deleted file mode 100644 > index 42d8814f903a..000000000000 > --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt > +++ /dev/null > @@ -1,121 +0,0 @@ > -MT8173 xHCI > - > -The device node for Mediatek SOC USB3.0 host controller > - > -There are two scenarios: the first one only supports xHCI driver; > -the second one supports dual-role mode, and the host is based on xHCI > -driver. Take account of backward compatibility, we divide bindings > -into two parts. > - > -1st: only supports xHCI driver > ------------------------------------------------------------------------- > - > -Required properties: > - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", > - soc-model is the name of SoC, such as mt8173, mt2712 etc, when using > - "mediatek,mtk-xhci" compatible string, you need SoC specific ones in > - addition, one of: > - - "mediatek,mt8173-xhci" > - - reg : specifies physical base address and size of the registers > - - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control > - - interrupts : interrupt used by the controller > - - power-domains : a phandle to USB power domain node to control USB's > - mtcmos > - - vusb33-supply : regulator of USB avdd3.3v > - > - - clocks : a list of phandle + clock-specifier pairs, one for each > - entry in clock-names > - - clock-names : must contain > - "sys_ck": controller clock used by normal mode, > - the following ones are optional: > - "ref_ck": reference clock used by low power mode etc, > - "mcu_ck": mcu_bus clock for register access, > - "dma_ck": dma_bus clock for data transfer by DMA, > - "xhci_ck": controller clock > - > - - phys : see usb-hcd.yaml in the current directory > - > -Optional properties: > - - wakeup-source : enable USB remote wakeup; > - - mediatek,syscon-wakeup : phandle to syscon used to access the register > - of the USB wakeup glue layer between xHCI and SPM; it depends on > - "wakeup-source", and has two arguments: > - - the first one : register base address of the glue layer in syscon; > - - the second one : hardware version of the glue layer > - - 1 : used by mt8173 etc > - - 2 : used by mt2712 etc > - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, > - bit1 for u3port1, ... etc; > - - vbus-supply : reference to the VBUS regulator; > - - usb3-lpm-capable : supports USB3.0 LPM > - - pinctrl-names : a pinctrl state named "default" must be defined > - - pinctrl-0 : pin control group > - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt > - - imod-interval-ns: default interrupt moderation interval is 5000ns > - > -additionally the properties from usb-hcd.yaml (in the current directory) are > -supported. > - > -Example: > -usb30: usb@11270000 { > - compatible = "mediatek,mt8173-xhci"; > - reg = <0 0x11270000 0 0x1000>, > - <0 0x11280700 0 0x0100>; > - reg-names = "mac", "ippc"; > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, > - <&pericfg CLK_PERI_USB0>, > - <&pericfg CLK_PERI_USB1>; > - clock-names = "sys_ck", "ref_ck"; > - phys = <&phy_port0 PHY_TYPE_USB3>, > - <&phy_port1 PHY_TYPE_USB2>; > - vusb33-supply = <&mt6397_vusb_reg>; > - vbus-supply = <&usb_p1_vbus>; > - usb3-lpm-capable; > - mediatek,syscon-wakeup = <&pericfg 0x400 1>; > - wakeup-source; > - imod-interval-ns = <10000>; > -}; > - > -2nd: dual-role mode with xHCI driver > ------------------------------------------------------------------------- > - > -In the case, xhci is added as subnode to mtu3. An example and the DT binding > -details of mtu3 can be found in: > -Documentation/devicetree/bindings/usb/mediatek,mtu3.txt > - > -Required properties: > - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", > - soc-model is the name of SoC, such as mt8173, mt2712 etc, when using > - "mediatek,mtk-xhci" compatible string, you need SoC specific ones in > - addition, one of: > - - "mediatek,mt8173-xhci" > - - reg : specifies physical base address and size of the registers > - - reg-names: should be "mac" for xHCI MAC > - - interrupts : interrupt used by the host controller > - - power-domains : a phandle to USB power domain node to control USB's > - mtcmos > - - vusb33-supply : regulator of USB avdd3.3v > - > - - clocks : a list of phandle + clock-specifier pairs, one for each > - entry in clock-names > - - clock-names : must contain "sys_ck", and the following ones are optional: > - "ref_ck", "mcu_ck" and "dma_ck", "xhci_ck" > - > -Optional properties: > - - vbus-supply : reference to the VBUS regulator; > - - usb3-lpm-capable : supports USB3.0 LPM > - > -Example: > -usb30: usb@11270000 { > - compatible = "mediatek,mt8173-xhci"; > - reg = <0 0x11270000 0 0x1000>; > - reg-names = "mac"; > - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > - clock-names = "sys_ck", "ref_ck"; > - vusb33-supply = <&mt6397_vusb_reg>; > - usb3-lpm-capable; > -}; > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml > new file mode 100644 > index 000000000000..4a36ad5c4d25 > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml > @@ -0,0 +1,171 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright (c) 2020 MediaTek > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: MediaTek USB3 xHCI Device Tree Bindings > + > +maintainers: > + - Chunfeng Yun <chunfeng.yun@mediatek.com> > + > +allOf: > + - $ref: "usb-hcd.yaml" > + > +description: | > + There are two scenarios: > + case 1: only supports xHCI driver; > + case 2: supports dual-role mode, and the host is based on xHCI driver. > + > +properties: > + # common properties for both case 1 and case 2 > + compatible: > + items: > + - enum: > + - mediatek,mt2712-xhci > + - mediatek,mt7622-xhci > + - mediatek,mt7629-xhci > + - mediatek,mt8173-xhci > + - mediatek,mt8183-xhci > + - const: mediatek,mtk-xhci > + > + reg: > + minItems: 1 > + maxItems: 2 > + items: > + - description: the registers of xHCI MAC > + - description: the registers of IP Port Control > + > + reg-names: > + minItems: 1 > + maxItems: 2 > + items: > + - const: mac > + - const: ippc # optional, only needed for case 1. > + > + interrupts: > + maxItems: 1 > + > + power-domains: > + description: A phandle to USB power domain node to control USB's MTCMOS > + maxItems: 1 > + > + clocks: > + minItems: 1 > + maxItems: 5 > + items: > + - description: Controller clock used by normal mode > + - description: Reference clock used by low power mode etc > + - description: Mcu bus clock for register access > + - description: DMA bus clock for data transfer > + - description: controller clock > + > + clock-names: > + minItems: 1 > + maxItems: 5 > + items: > + - const: sys_ck # required, the following ones are optional > + - const: ref_ck > + - const: mcu_ck > + - const: dma_ck > + - const: xhci_ck > + > + phys: > + $ref: /usb/usb-hcd.yaml# That's not right. You need 'items' and list each entry. > + description: List of all the USB PHYs on this HCD > + > + vusb33-supply: > + description: Regulator of USB AVDD3.3v > + > + vbus-supply: > + description: Regulator of USB VBUS5v > + > + usb3-lpm-capable: > + description: supports USB3.0 LPM > + type: boolean > + > + imod-interval-ns: > + description: > + Interrupt moderation interval value, it is 8 times as much as that > + defined in the xHCI spec on MTK's controller. > + default: 5000 > + > + # the following properties are only used for case 1 > + wakeup-source: > + description: enable USB remote wakeup, see power/wakeup-source.txt > + type: boolean > + > + mediatek,syscon-wakeup: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + maxItems: 1 > + description: | > + A phandle to syscon used to access the register of the USB wakeup glue > + layer between xHCI and SPM, the field should always be 3 cells long. > + > + items: Indentation is wrong here. Should be 2 fewer spaces. > + - description: > + The first cell represents a phandle to syscon > + - description: > + The second cell represents the register base address of the glue > + layer in syscon > + - description: > + The third cell represents the hardware version of the glue layer, > + 1 is used by mt8173 etc, 2 is used by mt2712 etc > + enum: [1, 2] > + > + mediatek,u3p-dis-msk: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: The mask to disable u3ports, bit0 for u3port0, > + bit1 for u3port1, ... etc > + > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 0 > + > +patternProperties: > + "^[a-f]+@[0-9a-f]+$": > + $ref: /usb/usb-hcd.yaml# This $ref isn't right. You already referenced it at the top. > + type: object > + description: The hard wired USB devices. > + > +dependencies: > + wakeup-source: [ 'mediatek,syscon-wakeup' ] > + > +required: > + - compatible > + - reg > + - reg-names > + - interrupts > + - clocks > + - clock-names > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/mt8173-clk.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + #include <dt-bindings/phy/phy.h> > + #include <dt-bindings/power/mt8173-power.h> > + > + usb@11270000 { > + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; > + reg = <0x11270000 0x1000>, <0x11280700 0x0100>; > + reg-names = "mac", "ippc"; > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > + clock-names = "sys_ck", "ref_ck"; > + phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>; > + vusb33-supply = <&mt6397_vusb_reg>; > + vbus-supply = <&usb_p1_vbus>; > + imod-interval-ns = <10000>; > + mediatek,syscon-wakeup = <&pericfg 0x400 1>; > + wakeup-source; > + usb3-lpm-capable; > + }; > +... > -- > 2.18.0 >
On Mon, 2020-12-07 at 15:24 -0600, Rob Herring wrote: > On Wed, Nov 18, 2020 at 04:21:24PM +0800, Chunfeng Yun wrote: > > Convert mediatek,mtk-xhci.txt to YAML schema mediatek,mtk-xhci.yaml > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > --- > > v3: > > 1. fix yamllint warning > > 2. remove pinctrl* properties supported by default suggested by Rob > > 3. drop unused labels > > 4. modify description of mediatek,syscon-wakeup > > 5. remove type of imod-interval-ns > > > > v2: new patch > > --- > > .../bindings/usb/mediatek,mtk-xhci.txt | 121 ------------- > > .../bindings/usb/mediatek,mtk-xhci.yaml | 171 ++++++++++++++++++ > > 2 files changed, 171 insertions(+), 121 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt > > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml [...] > > diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml > > new file mode 100644 > > index 000000000000..4a36ad5c4d25 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml > > @@ -0,0 +1,171 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +# Copyright (c) 2020 MediaTek > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: MediaTek USB3 xHCI Device Tree Bindings > > + > > +maintainers: > > + - Chunfeng Yun <chunfeng.yun@mediatek.com> > > + > > +allOf: > > + - $ref: "usb-hcd.yaml" > > + > > +description: | > > + There are two scenarios: > > + case 1: only supports xHCI driver; > > + case 2: supports dual-role mode, and the host is based on xHCI driver. > > + > > +properties: > > + # common properties for both case 1 and case 2 > > + compatible: > > + items: > > + - enum: > > + - mediatek,mt2712-xhci > > + - mediatek,mt7622-xhci > > + - mediatek,mt7629-xhci > > + - mediatek,mt8173-xhci > > + - mediatek,mt8183-xhci > > + - const: mediatek,mtk-xhci > > + > > + reg: > > + minItems: 1 > > + maxItems: 2 > > + items: > > + - description: the registers of xHCI MAC > > + - description: the registers of IP Port Control > > + > > + reg-names: > > + minItems: 1 > > + maxItems: 2 > > + items: > > + - const: mac > > + - const: ippc # optional, only needed for case 1. > > + > > + interrupts: > > + maxItems: 1 > > + > > + power-domains: > > + description: A phandle to USB power domain node to control USB's MTCMOS > > + maxItems: 1 > > + > > + clocks: > > + minItems: 1 > > + maxItems: 5 > > + items: > > + - description: Controller clock used by normal mode > > + - description: Reference clock used by low power mode etc > > + - description: Mcu bus clock for register access > > + - description: DMA bus clock for data transfer > > + - description: controller clock > > + > > + clock-names: > > + minItems: 1 > > + maxItems: 5 > > + items: > > + - const: sys_ck # required, the following ones are optional > > + - const: ref_ck > > + - const: mcu_ck > > + - const: dma_ck > > + - const: xhci_ck > > + > > + phys: > > + $ref: /usb/usb-hcd.yaml# > > That's not right. > > You need 'items' and list each entry. Will add minItems/maxItems instead due to it's variable and phy-names is not used > > > + description: List of all the USB PHYs on this HCD > > + > > + vusb33-supply: > > + description: Regulator of USB AVDD3.3v > > + > > + vbus-supply: > > + description: Regulator of USB VBUS5v > > + > > + usb3-lpm-capable: > > + description: supports USB3.0 LPM > > + type: boolean > > + > > + imod-interval-ns: > > + description: > > + Interrupt moderation interval value, it is 8 times as much as that > > + defined in the xHCI spec on MTK's controller. > > + default: 5000 > > + > > + # the following properties are only used for case 1 > > + wakeup-source: > > + description: enable USB remote wakeup, see power/wakeup-source.txt > > + type: boolean > > + > > + mediatek,syscon-wakeup: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + maxItems: 1 > > + description: | > > + A phandle to syscon used to access the register of the USB wakeup glue > > + layer between xHCI and SPM, the field should always be 3 cells long. > > + > > + items: > > Indentation is wrong here. Should be 2 fewer spaces. Will fix it > > > + - description: > > + The first cell represents a phandle to syscon > > + - description: > > + The second cell represents the register base address of the glue > > + layer in syscon > > + - description: > > + The third cell represents the hardware version of the glue layer, > > + 1 is used by mt8173 etc, 2 is used by mt2712 etc > > + enum: [1, 2] > > + > > + mediatek,u3p-dis-msk: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: The mask to disable u3ports, bit0 for u3port0, > > + bit1 for u3port1, ... etc > > + > > + "#address-cells": > > + const: 1 > > + > > + "#size-cells": > > + const: 0 > > + > > +patternProperties: > > + "^[a-f]+@[0-9a-f]+$": > > + $ref: /usb/usb-hcd.yaml# > > This $ref isn't right. You already referenced it at the top. Will drop it Thank you > > > + type: object > > + description: The hard wired USB devices. > > + > > +dependencies: > > + wakeup-source: [ 'mediatek,syscon-wakeup' ] > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + - interrupts > > + - clocks > > + - clock-names > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/clock/mt8173-clk.h> > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/interrupt-controller/irq.h> > > + #include <dt-bindings/phy/phy.h> > > + #include <dt-bindings/power/mt8173-power.h> > > + > > + usb@11270000 { > > + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; > > + reg = <0x11270000 0x1000>, <0x11280700 0x0100>; > > + reg-names = "mac", "ippc"; > > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; > > + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; > > + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; > > + clock-names = "sys_ck", "ref_ck"; > > + phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>; > > + vusb33-supply = <&mt6397_vusb_reg>; > > + vbus-supply = <&usb_p1_vbus>; > > + imod-interval-ns = <10000>; > > + mediatek,syscon-wakeup = <&pericfg 0x400 1>; > > + wakeup-source; > > + usb3-lpm-capable; > > + }; > > +... > > -- > > 2.18.0 > >
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt deleted file mode 100644 index 42d8814f903a..000000000000 --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt +++ /dev/null @@ -1,121 +0,0 @@ -MT8173 xHCI - -The device node for Mediatek SOC USB3.0 host controller - -There are two scenarios: the first one only supports xHCI driver; -the second one supports dual-role mode, and the host is based on xHCI -driver. Take account of backward compatibility, we divide bindings -into two parts. - -1st: only supports xHCI driver ------------------------------------------------------------------------- - -Required properties: - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", - soc-model is the name of SoC, such as mt8173, mt2712 etc, when using - "mediatek,mtk-xhci" compatible string, you need SoC specific ones in - addition, one of: - - "mediatek,mt8173-xhci" - - reg : specifies physical base address and size of the registers - - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control - - interrupts : interrupt used by the controller - - power-domains : a phandle to USB power domain node to control USB's - mtcmos - - vusb33-supply : regulator of USB avdd3.3v - - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain - "sys_ck": controller clock used by normal mode, - the following ones are optional: - "ref_ck": reference clock used by low power mode etc, - "mcu_ck": mcu_bus clock for register access, - "dma_ck": dma_bus clock for data transfer by DMA, - "xhci_ck": controller clock - - - phys : see usb-hcd.yaml in the current directory - -Optional properties: - - wakeup-source : enable USB remote wakeup; - - mediatek,syscon-wakeup : phandle to syscon used to access the register - of the USB wakeup glue layer between xHCI and SPM; it depends on - "wakeup-source", and has two arguments: - - the first one : register base address of the glue layer in syscon; - - the second one : hardware version of the glue layer - - 1 : used by mt8173 etc - - 2 : used by mt2712 etc - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, - bit1 for u3port1, ... etc; - - vbus-supply : reference to the VBUS regulator; - - usb3-lpm-capable : supports USB3.0 LPM - - pinctrl-names : a pinctrl state named "default" must be defined - - pinctrl-0 : pin control group - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - - imod-interval-ns: default interrupt moderation interval is 5000ns - -additionally the properties from usb-hcd.yaml (in the current directory) are -supported. - -Example: -usb30: usb@11270000 { - compatible = "mediatek,mt8173-xhci"; - reg = <0 0x11270000 0 0x1000>, - <0 0x11280700 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, - <&pericfg CLK_PERI_USB0>, - <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck"; - phys = <&phy_port0 PHY_TYPE_USB3>, - <&phy_port1 PHY_TYPE_USB2>; - vusb33-supply = <&mt6397_vusb_reg>; - vbus-supply = <&usb_p1_vbus>; - usb3-lpm-capable; - mediatek,syscon-wakeup = <&pericfg 0x400 1>; - wakeup-source; - imod-interval-ns = <10000>; -}; - -2nd: dual-role mode with xHCI driver ------------------------------------------------------------------------- - -In the case, xhci is added as subnode to mtu3. An example and the DT binding -details of mtu3 can be found in: -Documentation/devicetree/bindings/usb/mediatek,mtu3.txt - -Required properties: - - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", - soc-model is the name of SoC, such as mt8173, mt2712 etc, when using - "mediatek,mtk-xhci" compatible string, you need SoC specific ones in - addition, one of: - - "mediatek,mt8173-xhci" - - reg : specifies physical base address and size of the registers - - reg-names: should be "mac" for xHCI MAC - - interrupts : interrupt used by the host controller - - power-domains : a phandle to USB power domain node to control USB's - mtcmos - - vusb33-supply : regulator of USB avdd3.3v - - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain "sys_ck", and the following ones are optional: - "ref_ck", "mcu_ck" and "dma_ck", "xhci_ck" - -Optional properties: - - vbus-supply : reference to the VBUS regulator; - - usb3-lpm-capable : supports USB3.0 LPM - -Example: -usb30: usb@11270000 { - compatible = "mediatek,mt8173-xhci"; - reg = <0 0x11270000 0 0x1000>; - reg-names = "mac"; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; - clock-names = "sys_ck", "ref_ck"; - vusb33-supply = <&mt6397_vusb_reg>; - usb3-lpm-capable; -}; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml new file mode 100644 index 000000000000..4a36ad5c4d25 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml @@ -0,0 +1,171 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek USB3 xHCI Device Tree Bindings + +maintainers: + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +allOf: + - $ref: "usb-hcd.yaml" + +description: | + There are two scenarios: + case 1: only supports xHCI driver; + case 2: supports dual-role mode, and the host is based on xHCI driver. + +properties: + # common properties for both case 1 and case 2 + compatible: + items: + - enum: + - mediatek,mt2712-xhci + - mediatek,mt7622-xhci + - mediatek,mt7629-xhci + - mediatek,mt8173-xhci + - mediatek,mt8183-xhci + - const: mediatek,mtk-xhci + + reg: + minItems: 1 + maxItems: 2 + items: + - description: the registers of xHCI MAC + - description: the registers of IP Port Control + + reg-names: + minItems: 1 + maxItems: 2 + items: + - const: mac + - const: ippc # optional, only needed for case 1. + + interrupts: + maxItems: 1 + + power-domains: + description: A phandle to USB power domain node to control USB's MTCMOS + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 5 + items: + - description: Controller clock used by normal mode + - description: Reference clock used by low power mode etc + - description: Mcu bus clock for register access + - description: DMA bus clock for data transfer + - description: controller clock + + clock-names: + minItems: 1 + maxItems: 5 + items: + - const: sys_ck # required, the following ones are optional + - const: ref_ck + - const: mcu_ck + - const: dma_ck + - const: xhci_ck + + phys: + $ref: /usb/usb-hcd.yaml# + description: List of all the USB PHYs on this HCD + + vusb33-supply: + description: Regulator of USB AVDD3.3v + + vbus-supply: + description: Regulator of USB VBUS5v + + usb3-lpm-capable: + description: supports USB3.0 LPM + type: boolean + + imod-interval-ns: + description: + Interrupt moderation interval value, it is 8 times as much as that + defined in the xHCI spec on MTK's controller. + default: 5000 + + # the following properties are only used for case 1 + wakeup-source: + description: enable USB remote wakeup, see power/wakeup-source.txt + type: boolean + + mediatek,syscon-wakeup: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: | + A phandle to syscon used to access the register of the USB wakeup glue + layer between xHCI and SPM, the field should always be 3 cells long. + + items: + - description: + The first cell represents a phandle to syscon + - description: + The second cell represents the register base address of the glue + layer in syscon + - description: + The third cell represents the hardware version of the glue layer, + 1 is used by mt8173 etc, 2 is used by mt2712 etc + enum: [1, 2] + + mediatek,u3p-dis-msk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^[a-f]+@[0-9a-f]+$": + $ref: /usb/usb-hcd.yaml# + type: object + description: The hard wired USB devices. + +dependencies: + wakeup-source: [ 'mediatek,syscon-wakeup' ] + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/phy/phy.h> + #include <dt-bindings/power/mt8173-power.h> + + usb@11270000 { + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; + reg = <0x11270000 0x1000>, <0x11280700 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p1_vbus>; + imod-interval-ns = <10000>; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; + wakeup-source; + usb3-lpm-capable; + }; +...
Convert mediatek,mtk-xhci.txt to YAML schema mediatek,mtk-xhci.yaml Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- v3: 1. fix yamllint warning 2. remove pinctrl* properties supported by default suggested by Rob 3. drop unused labels 4. modify description of mediatek,syscon-wakeup 5. remove type of imod-interval-ns v2: new patch --- .../bindings/usb/mediatek,mtk-xhci.txt | 121 ------------- .../bindings/usb/mediatek,mtk-xhci.yaml | 171 ++++++++++++++++++ 2 files changed, 171 insertions(+), 121 deletions(-) delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml