@@ -284,11 +284,12 @@ static int ti_vsend_sync(struct usb_device *dev, u8 request, u16 value,
return 0;
}
-static int send_cmd(struct usb_device *dev, u8 command, u8 moduleid,
- u16 value, void *data, int size)
+static int send_port_cmd(struct usb_serial_port *port, u8 command, u16 value,
+ void *data, int size)
{
- return ti_vsend_sync(dev, command, value, moduleid, data, size,
- TI_VSEND_TIMEOUT_DEFAULT);
+ return ti_vsend_sync(port->serial->dev, command, value,
+ UMPM_UART1_PORT + port->port_number,
+ data, size, TI_VSEND_TIMEOUT_DEFAULT);
}
/* clear tx/rx buffers and fifo in TI UMP */
@@ -298,12 +299,7 @@ static int purge_port(struct usb_serial_port *port, __u16 mask)
dev_dbg(&port->dev, "%s - port %d, mask %x\n", __func__, port_number, mask);
- return send_cmd(port->serial->dev,
- UMPC_PURGE_PORT,
- (__u8)(UMPM_UART1_PORT + port_number),
- mask,
- NULL,
- 0);
+ return send_port_cmd(port, UMPC_PURGE_PORT, mask, NULL, 0);
}
/**
@@ -1500,12 +1496,9 @@ static int do_boot_mode(struct edgeport_serial *serial,
static int ti_do_config(struct edgeport_port *port, int feature, int on)
{
- int port_number = port->port->port_number;
-
on = !!on; /* 1 or 0 not bitmask */
- return send_cmd(port->port->serial->dev,
- feature, (__u8)(UMPM_UART1_PORT + port_number),
- on, NULL, 0);
+
+ return send_port_cmd(port->port, feature, on, NULL, 0);
}
static int restore_mcr(struct edgeport_port *port, __u8 mcr)
@@ -1874,8 +1867,7 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
dev_dbg(&port->dev, "%s - Sending UMPC_OPEN_PORT\n", __func__);
/* Tell TI to open and start the port */
- status = send_cmd(dev, UMPC_OPEN_PORT,
- (u8)(UMPM_UART1_PORT + port_number), open_settings, NULL, 0);
+ status = send_port_cmd(port, UMPC_OPEN_PORT, open_settings, NULL, 0);
if (status) {
dev_err(&port->dev, "%s - cannot send open command, %d\n",
__func__, status);
@@ -1883,8 +1875,7 @@ static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
}
/* Start the DMA? */
- status = send_cmd(dev, UMPC_START_PORT,
- (u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0);
+ status = send_port_cmd(port, UMPC_START_PORT, 0, NULL, 0);
if (status) {
dev_err(&port->dev, "%s - cannot send start DMA command, %d\n",
__func__, status);
@@ -1967,9 +1958,7 @@ static void edge_close(struct usb_serial_port *port)
{
struct edgeport_serial *edge_serial;
struct edgeport_port *edge_port;
- struct usb_serial *serial = port->serial;
unsigned long flags;
- int port_number;
edge_serial = usb_get_serial_data(port->serial);
edge_port = usb_get_serial_port_data(port);
@@ -1990,9 +1979,7 @@ static void edge_close(struct usb_serial_port *port)
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
dev_dbg(&port->dev, "%s - send umpc_close_port\n", __func__);
- port_number = port->port_number;
- send_cmd(serial->dev, UMPC_CLOSE_PORT,
- (__u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0);
+ send_port_cmd(port, UMPC_CLOSE_PORT, 0, NULL, 0);
mutex_lock(&edge_serial->es_lock);
--edge_port->edge_serial->num_ports_open;
@@ -2225,7 +2212,6 @@ static void change_port_settings(struct tty_struct *tty,
int baud;
unsigned cflag;
int status;
- int port_number = edge_port->port->port_number;
config = kmalloc (sizeof (*config), GFP_KERNEL);
if (!config) {
@@ -2351,9 +2337,8 @@ static void change_port_settings(struct tty_struct *tty,
cpu_to_be16s(&config->wFlags);
cpu_to_be16s(&config->wBaudRate);
- status = send_cmd(edge_port->port->serial->dev, UMPC_SET_CONFIG,
- (__u8)(UMPM_UART1_PORT + port_number),
- 0, config, sizeof(*config));
+ status = send_port_cmd(edge_port->port, UMPC_SET_CONFIG, 0, config,
+ sizeof(*config));
if (status)
dev_dbg(dev, "%s - error %d when trying to write config to device\n",
__func__, status);
Add a send-port-command helper which takes care of determining the UART module id when sending commands instead of doing so at every call site. Signed-off-by: Johan Hovold <johan@kernel.org> --- drivers/usb/serial/io_ti.c | 41 ++++++++++++-------------------------- 1 file changed, 13 insertions(+), 28 deletions(-)