| Message ID | 20210902213500.3795948-2-pmalani@chromium.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Type C partner power supply and PDO support. | expand |
Hi Prashant, On Thu, Sep 02, 2021 at 02:34:58PM -0700, Prashant Malani wrote: > Increase the max number of PDO objects to 13, to accommodate the extra > PDOs added as a part of EPR (Extended Power Range) operation introduced > in the USB PD Spec Rev 3.1, v 1.0. See Figure 6-54 for details. > > Signed-off-by: Prashant Malani <pmalani@chromium.org> > --- > include/linux/usb/pd.h | 8 +++++++- > 1 file changed, 7 insertions(+), 1 deletion(-) > > diff --git a/include/linux/usb/pd.h b/include/linux/usb/pd.h > index 96b7ff66f074..7e8bdca1ce6e 100644 > --- a/include/linux/usb/pd.h > +++ b/include/linux/usb/pd.h > @@ -201,7 +201,13 @@ struct pd_message { > } __packed; > > /* PDO: Power Data Object */ > -#define PDO_MAX_OBJECTS 7 > + > +/* > + * The EPR (Extended Power Range) structure is a superset of the SPR (Standard Power Range) > + * capabilities structure, so set the max number of PDOs to 13 instead of 7. On SPR-only systems, > + * objects 8 through 13 will just be empty. > + */ > +#define PDO_MAX_OBJECTS 13 Hmm this might break the recent change I made to UCSI in commit 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4"). 520 static void ucsi_get_src_pdos(struct ucsi_connector *con, int is_partner) 521 { 522 int ret; 523 524 /* UCSI max payload means only getting at most 4 PDOs at a time */ 525 ret = ucsi_get_pdos(con, 1, con->src_pdos, 0, UCSI_MAX_PDOS); 526 if (ret < 0) 527 return; 528 529 con->num_pdos = ret / sizeof(u32); /* number of bytes to 32-bit PDOs */ 530 if (con->num_pdos < UCSI_MAX_PDOS) 531 return; 532 533 /* get the remaining PDOs, if any */ 534 ret = ucsi_get_pdos(con, 1, con->src_pdos, UCSI_MAX_PDOS, 535 PDO_MAX_OBJECTS - UCSI_MAX_PDOS); ^^^^^^^^^^^^^^^ This routine calls the UCSI GET_PDOS command for up to 4 PDOs at a time since that's the most the return payload can carry. Currently this assumes that we'd only need to request the PPM at most twice to retrieve all the PDOs for up to a maximum of 7 (first request for 4 then again if needed for the remaining 3). I'm not sure if any existing UCSI FW would be updatable to support more than 7 PDOs in the future, much less support EPR. In fact, current UCSI 1.2 spec [1] Table 4-34 mentions PDO offset valid values are 0-7 and anything else "shall not be used", so I don't know how UCSI will eventually cope with EPR without a spec update. So if this macro changes to 13 then this call would result in a call to the UCSI GET_PDOS command passing num_pdos == 13-4 = 9 which would probably result in an error from the PPM FW. So we might need to retain the maximum value of 7 PDOs at least for UCSI here. Maybe that means this UCSI driver needs to carry its own definition of UCSI_MAX_TOTAL_PDOS=7 instead of using PDO_MAX_OBJECTS? Jack
On Thu, Sep 02, 2021 at 11:47:01PM -0700, Jack Pham wrote: > Hi Prashant, > > On Thu, Sep 02, 2021 at 02:34:58PM -0700, Prashant Malani wrote: > > Increase the max number of PDO objects to 13, to accommodate the extra > > PDOs added as a part of EPR (Extended Power Range) operation introduced > > in the USB PD Spec Rev 3.1, v 1.0. See Figure 6-54 for details. > > > > Signed-off-by: Prashant Malani <pmalani@chromium.org> > > --- > > include/linux/usb/pd.h | 8 +++++++- > > 1 file changed, 7 insertions(+), 1 deletion(-) > > > > diff --git a/include/linux/usb/pd.h b/include/linux/usb/pd.h > > index 96b7ff66f074..7e8bdca1ce6e 100644 > > --- a/include/linux/usb/pd.h > > +++ b/include/linux/usb/pd.h > > @@ -201,7 +201,13 @@ struct pd_message { > > } __packed; > > > > /* PDO: Power Data Object */ > > -#define PDO_MAX_OBJECTS 7 > > + > > +/* > > + * The EPR (Extended Power Range) structure is a superset of the SPR (Standard Power Range) > > + * capabilities structure, so set the max number of PDOs to 13 instead of 7. On SPR-only systems, > > + * objects 8 through 13 will just be empty. > > + */ > > +#define PDO_MAX_OBJECTS 13 > > Hmm this might break the recent change I made to UCSI in commit > 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just > the first 4"). > > 520 static void ucsi_get_src_pdos(struct ucsi_connector *con, int is_partner) > 521 { > 522 int ret; > 523 > 524 /* UCSI max payload means only getting at most 4 PDOs at a time */ > 525 ret = ucsi_get_pdos(con, 1, con->src_pdos, 0, UCSI_MAX_PDOS); > 526 if (ret < 0) > 527 return; > 528 > 529 con->num_pdos = ret / sizeof(u32); /* number of bytes to 32-bit PDOs */ > 530 if (con->num_pdos < UCSI_MAX_PDOS) > 531 return; > 532 > 533 /* get the remaining PDOs, if any */ > 534 ret = ucsi_get_pdos(con, 1, con->src_pdos, UCSI_MAX_PDOS, > 535 PDO_MAX_OBJECTS - UCSI_MAX_PDOS); > ^^^^^^^^^^^^^^^ > This routine calls the UCSI GET_PDOS command for up to 4 PDOs at a time > since that's the most the return payload can carry. Currently this > assumes that we'd only need to request the PPM at most twice to retrieve > all the PDOs for up to a maximum of 7 (first request for 4 then again if > needed for the remaining 3). I'm not sure if any existing UCSI FW would > be updatable to support more than 7 PDOs in the future, much less > support EPR. In fact, current UCSI 1.2 spec [1] Table 4-34 mentions PDO Sorry, forgot the footnote with the link to the spec: [1] https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/usb-type-c-ucsi-spec.pdf > offset valid values are 0-7 and anything else "shall not be used", so I > don't know how UCSI will eventually cope with EPR without a spec update. > > So if this macro changes to 13 then this call would result in a call to > the UCSI GET_PDOS command passing num_pdos == 13-4 = 9 which would > probably result in an error from the PPM FW. So we might need to retain > the maximum value of 7 PDOs at least for UCSI here. Maybe that means > this UCSI driver needs to carry its own definition of > UCSI_MAX_TOTAL_PDOS=7 instead of using PDO_MAX_OBJECTS? > > Jack
Hi Jack, Thanks for taking a look at the patch. On Fri, Sep 3, 2021 at 11:05 AM Jack Pham <jackp@codeaurora.org> wrote: > > On Thu, Sep 02, 2021 at 11:47:01PM -0700, Jack Pham wrote: > > Hi Prashant, > > > > On Thu, Sep 02, 2021 at 02:34:58PM -0700, Prashant Malani wrote: > > > Increase the max number of PDO objects to 13, to accommodate the extra > > > PDOs added as a part of EPR (Extended Power Range) operation introduced > > > in the USB PD Spec Rev 3.1, v 1.0. See Figure 6-54 for details. > > > > > > Signed-off-by: Prashant Malani <pmalani@chromium.org> > > > --- > > > include/linux/usb/pd.h | 8 +++++++- > > > 1 file changed, 7 insertions(+), 1 deletion(-) > > > > > > diff --git a/include/linux/usb/pd.h b/include/linux/usb/pd.h > > > index 96b7ff66f074..7e8bdca1ce6e 100644 > > > --- a/include/linux/usb/pd.h > > > +++ b/include/linux/usb/pd.h > > > @@ -201,7 +201,13 @@ struct pd_message { > > > } __packed; > > > > > > /* PDO: Power Data Object */ > > > -#define PDO_MAX_OBJECTS 7 > > > + > > > +/* > > > + * The EPR (Extended Power Range) structure is a superset of the SPR (Standard Power Range) > > > + * capabilities structure, so set the max number of PDOs to 13 instead of 7. On SPR-only systems, > > > + * objects 8 through 13 will just be empty. > > > + */ > > > +#define PDO_MAX_OBJECTS 13 > > > > Hmm this might break the recent change I made to UCSI in commit > > 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just > > the first 4"). > > > > 520 static void ucsi_get_src_pdos(struct ucsi_connector *con, int is_partner) > > 521 { > > 522 int ret; > > 523 > > 524 /* UCSI max payload means only getting at most 4 PDOs at a time */ > > 525 ret = ucsi_get_pdos(con, 1, con->src_pdos, 0, UCSI_MAX_PDOS); > > 526 if (ret < 0) > > 527 return; > > 528 > > 529 con->num_pdos = ret / sizeof(u32); /* number of bytes to 32-bit PDOs */ > > 530 if (con->num_pdos < UCSI_MAX_PDOS) > > 531 return; > > 532 > > 533 /* get the remaining PDOs, if any */ > > 534 ret = ucsi_get_pdos(con, 1, con->src_pdos, UCSI_MAX_PDOS, > > 535 PDO_MAX_OBJECTS - UCSI_MAX_PDOS); > > ^^^^^^^^^^^^^^^ > > This routine calls the UCSI GET_PDOS command for up to 4 PDOs at a time > > since that's the most the return payload can carry. Currently this > > assumes that we'd only need to request the PPM at most twice to retrieve > > all the PDOs for up to a maximum of 7 (first request for 4 then again if > > needed for the remaining 3). I'm not sure if any existing UCSI FW would > > be updatable to support more than 7 PDOs in the future, much less > > support EPR. In fact, current UCSI 1.2 spec [1] Table 4-34 mentions PDO > > Sorry, forgot the footnote with the link to the spec: > [1] https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/usb-type-c-ucsi-spec.pdf > > > offset valid values are 0-7 and anything else "shall not be used", so I > > don't know how UCSI will eventually cope with EPR without a spec update. > > > > So if this macro changes to 13 then this call would result in a call to > > the UCSI GET_PDOS command passing num_pdos == 13-4 = 9 which would > > probably result in an error from the PPM FW. So we might need to retain > > the maximum value of 7 PDOs at least for UCSI here. Maybe that means > > this UCSI driver needs to carry its own definition of > > UCSI_MAX_TOTAL_PDOS=7 instead of using PDO_MAX_OBJECTS? Thanks for pointing this out. We can perhaps just add another macro for EPR_PDO_MAX_OBJECTS, and leave the current macro as is for now. Best regards,
Hi Jack, On Thu, Sep 02, 2021 at 11:47:01PM -0700, Jack Pham wrote: > Hi Prashant, > > On Thu, Sep 02, 2021 at 02:34:58PM -0700, Prashant Malani wrote: > > Increase the max number of PDO objects to 13, to accommodate the extra > > PDOs added as a part of EPR (Extended Power Range) operation introduced > > in the USB PD Spec Rev 3.1, v 1.0. See Figure 6-54 for details. > > > > Signed-off-by: Prashant Malani <pmalani@chromium.org> > > --- > > include/linux/usb/pd.h | 8 +++++++- > > 1 file changed, 7 insertions(+), 1 deletion(-) > > > > diff --git a/include/linux/usb/pd.h b/include/linux/usb/pd.h > > index 96b7ff66f074..7e8bdca1ce6e 100644 > > --- a/include/linux/usb/pd.h > > +++ b/include/linux/usb/pd.h > > @@ -201,7 +201,13 @@ struct pd_message { > > } __packed; > > > > /* PDO: Power Data Object */ > > -#define PDO_MAX_OBJECTS 7 > > + > > +/* > > + * The EPR (Extended Power Range) structure is a superset of the SPR (Standard Power Range) > > + * capabilities structure, so set the max number of PDOs to 13 instead of 7. On SPR-only systems, > > + * objects 8 through 13 will just be empty. > > + */ > > +#define PDO_MAX_OBJECTS 13 > > Hmm this might break the recent change I made to UCSI in commit > 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just > the first 4"). > > 520 static void ucsi_get_src_pdos(struct ucsi_connector *con, int is_partner) > 521 { > 522 int ret; > 523 > 524 /* UCSI max payload means only getting at most 4 PDOs at a time */ > 525 ret = ucsi_get_pdos(con, 1, con->src_pdos, 0, UCSI_MAX_PDOS); > 526 if (ret < 0) > 527 return; > 528 > 529 con->num_pdos = ret / sizeof(u32); /* number of bytes to 32-bit PDOs */ > 530 if (con->num_pdos < UCSI_MAX_PDOS) > 531 return; > 532 > 533 /* get the remaining PDOs, if any */ > 534 ret = ucsi_get_pdos(con, 1, con->src_pdos, UCSI_MAX_PDOS, > 535 PDO_MAX_OBJECTS - UCSI_MAX_PDOS); > ^^^^^^^^^^^^^^^ > This routine calls the UCSI GET_PDOS command for up to 4 PDOs at a time > since that's the most the return payload can carry. Currently this > assumes that we'd only need to request the PPM at most twice to retrieve > all the PDOs for up to a maximum of 7 (first request for 4 then again if > needed for the remaining 3). I'm not sure if any existing UCSI FW would > be updatable to support more than 7 PDOs in the future, much less > support EPR. In fact, current UCSI 1.2 spec [1] Table 4-34 mentions PDO > offset valid values are 0-7 and anything else "shall not be used", so I > don't know how UCSI will eventually cope with EPR without a spec update. > I've had a conversation with Dmitriy Berchanskiy at Intel (the UCSI WG Chair) about this, and it sounds like the UCSI spec is planned on being revved (post R2.0) in order to support the additional messages and expanded structures of USB PD R3.1 around EPR. > So if this macro changes to 13 then this call would result in a call to > the UCSI GET_PDOS command passing num_pdos == 13-4 = 9 which would > probably result in an error from the PPM FW. So we might need to retain > the maximum value of 7 PDOs at least for UCSI here. Maybe that means > this UCSI driver needs to carry its own definition of > UCSI_MAX_TOTAL_PDOS=7 instead of using PDO_MAX_OBJECTS? > Prashant mentioned this as well, but maybe it makes sense to define a separate EPR_PDO_MAX_OBJECTS to handle the EPR case, as there are completely separate underlying PD messages (EPR_Source_Capabilities) where we expect up to 13 objects, and the classic SPR Source and Sink capabilities will still have the 7 object limit. Thanks, Benson > Jack > -- > The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, > a Linux Foundation Collaborative Project
Hi Benson, On Tue, Sep 07, 2021 at 04:28:53PM -0700, Benson Leung wrote: > Hi Jack, > > On Thu, Sep 02, 2021 at 11:47:01PM -0700, Jack Pham wrote: > > Hi Prashant, > > > > On Thu, Sep 02, 2021 at 02:34:58PM -0700, Prashant Malani wrote: > > > Increase the max number of PDO objects to 13, to accommodate the extra > > > PDOs added as a part of EPR (Extended Power Range) operation introduced > > > in the USB PD Spec Rev 3.1, v 1.0. See Figure 6-54 for details. > > > > > > Signed-off-by: Prashant Malani <pmalani@chromium.org> > > > --- > > > include/linux/usb/pd.h | 8 +++++++- > > > 1 file changed, 7 insertions(+), 1 deletion(-) > > > > > > diff --git a/include/linux/usb/pd.h b/include/linux/usb/pd.h > > > index 96b7ff66f074..7e8bdca1ce6e 100644 > > > --- a/include/linux/usb/pd.h > > > +++ b/include/linux/usb/pd.h > > > @@ -201,7 +201,13 @@ struct pd_message { > > > } __packed; > > > > > > /* PDO: Power Data Object */ > > > -#define PDO_MAX_OBJECTS 7 > > > + > > > +/* > > > + * The EPR (Extended Power Range) structure is a superset of the SPR (Standard Power Range) > > > + * capabilities structure, so set the max number of PDOs to 13 instead of 7. On SPR-only systems, > > > + * objects 8 through 13 will just be empty. > > > + */ > > > +#define PDO_MAX_OBJECTS 13 > > > > Hmm this might break the recent change I made to UCSI in commit > > 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just > > the first 4"). > > > > 520 static void ucsi_get_src_pdos(struct ucsi_connector *con, int is_partner) > > 521 { > > 522 int ret; > > 523 > > 524 /* UCSI max payload means only getting at most 4 PDOs at a time */ > > 525 ret = ucsi_get_pdos(con, 1, con->src_pdos, 0, UCSI_MAX_PDOS); > > 526 if (ret < 0) > > 527 return; > > 528 > > 529 con->num_pdos = ret / sizeof(u32); /* number of bytes to 32-bit PDOs */ > > 530 if (con->num_pdos < UCSI_MAX_PDOS) > > 531 return; > > 532 > > 533 /* get the remaining PDOs, if any */ > > 534 ret = ucsi_get_pdos(con, 1, con->src_pdos, UCSI_MAX_PDOS, > > 535 PDO_MAX_OBJECTS - UCSI_MAX_PDOS); > > ^^^^^^^^^^^^^^^ > > This routine calls the UCSI GET_PDOS command for up to 4 PDOs at a time > > since that's the most the return payload can carry. Currently this > > assumes that we'd only need to request the PPM at most twice to retrieve > > all the PDOs for up to a maximum of 7 (first request for 4 then again if > > needed for the remaining 3). I'm not sure if any existing UCSI FW would > > be updatable to support more than 7 PDOs in the future, much less > > support EPR. In fact, current UCSI 1.2 spec [1] Table 4-34 mentions PDO > > offset valid values are 0-7 and anything else "shall not be used", so I > > don't know how UCSI will eventually cope with EPR without a spec update. > > > > I've had a conversation with Dmitriy Berchanskiy at Intel (the UCSI WG Chair) > about this, and it sounds like the UCSI spec is planned on being revved > (post R2.0) in order to support the additional messages and expanded structures > of USB PD R3.1 around EPR. Good to know! Look forward to seeing it once it's ready. I've access to the current R2.0 draft as well, and it looks like there's gonna be a bit of work to update this driver to support it. The big standout is the data structure format change to accommodate much larger payloads. So I guess that bridge will be constructed when we get there, both for 2.0 and later for EPR. > > So if this macro changes to 13 then this call would result in a call to > > the UCSI GET_PDOS command passing num_pdos == 13-4 = 9 which would > > probably result in an error from the PPM FW. So we might need to retain > > the maximum value of 7 PDOs at least for UCSI here. Maybe that means > > this UCSI driver needs to carry its own definition of > > UCSI_MAX_TOTAL_PDOS=7 instead of using PDO_MAX_OBJECTS? > > > > Prashant mentioned this as well, but maybe it makes sense to define a separate > EPR_PDO_MAX_OBJECTS to handle the EPR case, as there are completely separate > underlying PD messages (EPR_Source_Capabilities) where we expect up to 13 > objects, and the classic SPR Source and Sink capabilities will still have the > 7 object limit. Sounds good to me FWIW. Plus this will even avoid unnecessarily bloating TCPM's internal {source,sink}_caps and {src,snk}_pdo arrays (an additional 96 bytes) prematurely before that driver is ready to be updated to handle EPR with all the new messages and states needed. Thanks, Jack
diff --git a/include/linux/usb/pd.h b/include/linux/usb/pd.h index 96b7ff66f074..7e8bdca1ce6e 100644 --- a/include/linux/usb/pd.h +++ b/include/linux/usb/pd.h @@ -201,7 +201,13 @@ struct pd_message { } __packed; /* PDO: Power Data Object */ -#define PDO_MAX_OBJECTS 7 + +/* + * The EPR (Extended Power Range) structure is a superset of the SPR (Standard Power Range) + * capabilities structure, so set the max number of PDOs to 13 instead of 7. On SPR-only systems, + * objects 8 through 13 will just be empty. + */ +#define PDO_MAX_OBJECTS 13 enum pd_pdo_type { PDO_TYPE_FIXED = 0,
Increase the max number of PDO objects to 13, to accommodate the extra PDOs added as a part of EPR (Extended Power Range) operation introduced in the USB PD Spec Rev 3.1, v 1.0. See Figure 6-54 for details. Signed-off-by: Prashant Malani <pmalani@chromium.org> --- include/linux/usb/pd.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)