| Message ID | 20220127200636.1456175-6-sean.anderson@seco.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | usb: dwc3: Calculate REFCLKPER et. al. from reference clock | expand |
Sean Anderson wrote: > This property allows setting the reference clock frequency properly for > ACPI-based systems. It is not documented under dt-bindings, since it is > not intended for use on DT-based systems. DT-based systems should use > the clocks property instead. > > Frequency is preferred over period since it has greater precision when > used in calculations. > > Signed-off-by: Sean Anderson <sean.anderson@seco.com> > --- > > (no changes since v2) > > Changes in v2: > - New > > drivers/usb/dwc3/core.c | 6 ++++-- > drivers/usb/dwc3/core.h | 4 +++- > 2 files changed, 7 insertions(+), 3 deletions(-) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index 18adddfba3da..c1b045121672 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -353,8 +353,8 @@ static void dwc3_ref_clk_period(struct dwc3 *dwc) > unsigned long rate; > u32 reg; > > - if (dwc->ref_clk) { > - rate = clk_get_rate(dwc->ref_clk); > + if (dwc->ref_clk || dwc->ref_clk_freq) { > + rate = clk_get_rate(dwc->ref_clk) ?: dwc->ref_clk_freq; > if (!rate) > return; > period = NSEC_PER_SEC / rate; > @@ -1497,6 +1497,8 @@ static void dwc3_get_properties(struct dwc3 *dwc) > &dwc->fladj); > device_property_read_u32(dev, "snps,ref-clock-period-ns", > &dwc->ref_clk_per); > + device_property_read_u32(dev, "snps,ref-clock-frequency-hz", > + &dwc->ref_clk_freq); > > dwc->dis_metastability_quirk = device_property_read_bool(dev, > "snps,dis_metastability_quirk"); > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index eb9c1efced05..00a792459fec 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -988,7 +988,8 @@ struct dwc3_scratchpad_array { > * @regs: base address for our registers > * @regs_size: address space size > * @fladj: frame length adjustment > - * @ref_clk_per: reference clock period configuration > + * @ref_clk_per: reference clock period; deprecated in favor of @ref_clk_freq > + * @ref_clk_freq: reference clock frequency to use if @ref_clk is missing > * @irq_gadget: peripheral controller's IRQ number > * @otg_irq: IRQ number for OTG IRQs > * @current_otg_role: current role of operation while using the OTG block > @@ -1171,6 +1172,7 @@ struct dwc3 { > > u32 fladj; > u32 ref_clk_per; > + u32 ref_clk_freq; > u32 irq_gadget; > u32 otg_irq; > u32 current_otg_role; Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Thanks, Thinh
Hi Andy, On 2/4/22 7:54 AM, Andy Shevchenko wrote: > > > On Thursday, January 27, 2022, Sean Anderson <sean.anderson@seco.com <mailto:sean.anderson@seco.com>> wrote: > > This property allows setting the reference clock frequency properly for > ACPI-based systems. It is not documented under dt-bindings, since it is > not intended for use on DT-based systems. DT-based systems should use > the clocks property instead. > > Frequency is preferred over period since it has greater precision when > used in > > Is it function or interface clock? > > We have standard property for the functional clock rate, I.e. “clock-frequency” (in Hz), can it be used here? I believe this is a "functional" clock. It it is a reference for the USB signals. I'm not sure exactly what the purpose of this clock is, since I do not have access to the databook for this IP. I considered using "clock-frequency", but I am concerned about ambiguity because there is a second "suspend" clock which is also a "functional" clock. The latter clock appears to be used when the PHY is shut down (and not necessarily corresponding to Linux's notion of a suspended device). If it is necessary in the future to configure that clock on ACPI platforms (e.g. to set GCTL.PWRDNSCALE) I think it is clear what the property name would be (snps,susp-clock-frequency-hz). --Sean > Signed-off-by: Sean Anderson <sean.anderson@seco.com <mailto:sean.anderson@seco.com>> > --- > > (no changes since v2) > > Changes in v2: > - New > > drivers/usb/dwc3/core.c | 6 ++++-- > drivers/usb/dwc3/core.h | 4 +++- > 2 files changed, 7 insertions(+), 3 deletions(-) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index 18adddfba3da..c1b045121672 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -353,8 +353,8 @@ static void dwc3_ref_clk_period(struct dwc3 *dwc) > unsigned long rate; > u32 reg; > > - if (dwc->ref_clk) { > - rate = clk_get_rate(dwc->ref_clk); > + if (dwc->ref_clk || dwc->ref_clk_freq) { > + rate = clk_get_rate(dwc->ref_clk) ?: dwc->ref_clk_freq; > if (!rate) > return; > period = NSEC_PER_SEC / rate; > @@ -1497,6 +1497,8 @@ static void dwc3_get_properties(struct dwc3 *dwc) > &dwc->fladj); > device_property_read_u32(dev, "snps,ref-clock-period-ns", > &dwc->ref_clk_per); > + device_property_read_u32(dev, "snps,ref-clock-frequency-hz", > + &dwc->ref_clk_freq); > > dwc->dis_metastability_quirk = device_property_read_bool(dev, > "snps,dis_metastability_quirk"); > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index eb9c1efced05..00a792459fec 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -988,7 +988,8 @@ struct dwc3_scratchpad_array { > * @regs: base address for our registers > * @regs_size: address space size > * @fladj: frame length adjustment > - * @ref_clk_per: reference clock period configuration > + * @ref_clk_per: reference clock period; deprecated in favor of @ref_clk_freq > + * @ref_clk_freq: reference clock frequency to use if @ref_clk is missing > * @irq_gadget: peripheral controller's IRQ number > * @otg_irq: IRQ number for OTG IRQs > * @current_otg_role: current role of operation while using the OTG block > @@ -1171,6 +1172,7 @@ struct dwc3 { > > u32 fladj; > u32 ref_clk_per; > + u32 ref_clk_freq; > u32 irq_gadget; > u32 otg_irq; > u32 current_otg_role; > -- > 2.25.1 > > > > -- > With Best Regards, > Andy Shevchenko > >
On Fri, Feb 4, 2022 at 6:00 PM Sean Anderson <sean.anderson@seco.com> wrote: > On 2/4/22 7:54 AM, Andy Shevchenko wrote: ... > > On Thursday, January 27, 2022, Sean Anderson <sean.anderson@seco.com <mailto:sean.anderson@seco.com>> wrote: > > Is it function or interface clock? > > > > We have standard property for the functional clock rate, I.e. “clock-frequency” (in Hz), can it be used here? > > I believe this is a "functional" clock. It it is a reference for the USB > signals. I'm not sure exactly what the purpose of this clock is, since I > do not have access to the databook for this IP. I considered using > "clock-frequency", but I am concerned about ambiguity because there is a > second "suspend" clock which is also a "functional" clock. The latter > clock appears to be used when the PHY is shut down (and not necessarily > corresponding to Linux's notion of a suspended device). If it is > necessary in the future to configure that clock on ACPI platforms (e.g. > to set GCTL.PWRDNSCALE) I think it is clear what the property name would > be (snps,susp-clock-frequency-hz). In order to have more or less unified APIs in the future I would suggest using 'clock-frequency' for the "main" functional clock. For example, 8250_dw uses it for the baud rate generator, while it also utilizes auxiliary clock(s) on some platforms.
On 2/4/22 1:38 PM, Andy Shevchenko wrote: > On Fri, Feb 4, 2022 at 6:00 PM Sean Anderson <sean.anderson@seco.com> wrote: >> On 2/4/22 7:54 AM, Andy Shevchenko wrote: > > ... > >> > On Thursday, January 27, 2022, Sean Anderson <sean.anderson@seco.com <mailto:sean.anderson@seco.com>> wrote: > >> > Is it function or interface clock? >> > >> > We have standard property for the functional clock rate, I.e. “clock-frequency” (in Hz), can it be used here? >> >> I believe this is a "functional" clock. It it is a reference for the USB >> signals. I'm not sure exactly what the purpose of this clock is, since I >> do not have access to the databook for this IP. I considered using >> "clock-frequency", but I am concerned about ambiguity because there is a >> second "suspend" clock which is also a "functional" clock. The latter >> clock appears to be used when the PHY is shut down (and not necessarily >> corresponding to Linux's notion of a suspended device). If it is >> necessary in the future to configure that clock on ACPI platforms (e.g. >> to set GCTL.PWRDNSCALE) I think it is clear what the property name would >> be (snps,susp-clock-frequency-hz). > > In order to have more or less unified APIs in the future I would > suggest using 'clock-frequency' for the "main" functional clock. For > example, 8250_dw uses it for the baud rate generator, while it also > utilizes auxiliary clock(s) on some platforms. > OK, I had a look though that driver, and it seems like it uses clock-frequency only for the baudclk, and e.g. apb_pclk has no corresponding frequency property. For this driver, it would mean that the suspend clock would only be configurable through device tree. Is that the approach you recommend? --Sean
On Fri, Feb 4, 2022 at 8:44 PM Sean Anderson <sean.anderson@seco.com> wrote: > On 2/4/22 1:38 PM, Andy Shevchenko wrote: > > On Fri, Feb 4, 2022 at 6:00 PM Sean Anderson <sean.anderson@seco.com> wrote: > >> On 2/4/22 7:54 AM, Andy Shevchenko wrote: > >> > On Thursday, January 27, 2022, Sean Anderson <sean.anderson@seco.com <mailto:sean.anderson@seco.com>> wrote: ... > > In order to have more or less unified APIs in the future I would > > suggest using 'clock-frequency' for the "main" functional clock. For > > example, 8250_dw uses it for the baud rate generator, while it also > > utilizes auxiliary clock(s) on some platforms. > > OK, I had a look though that driver, and it seems like it uses > clock-frequency only for the baudclk, and e.g. apb_pclk has no > corresponding frequency property. For this driver, it would mean that > the suspend clock would only be configurable through device tree. Is > that the approach you recommend? What I meant is to use the "clock-frequency" property as it is kinda standard de facto for the "main'' functional clock. The rest is up to the individual drivers. From the API perspective I would expect a common helper in the future that takes clock name and returns rate based on clock (if found) or "clock-frequency" property. We may also extend in far future to support any combinations of the [clock name, property name] to get a clock rated either via Device Tree or via ACPI.
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index 18adddfba3da..c1b045121672 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -353,8 +353,8 @@ static void dwc3_ref_clk_period(struct dwc3 *dwc) unsigned long rate; u32 reg; - if (dwc->ref_clk) { - rate = clk_get_rate(dwc->ref_clk); + if (dwc->ref_clk || dwc->ref_clk_freq) { + rate = clk_get_rate(dwc->ref_clk) ?: dwc->ref_clk_freq; if (!rate) return; period = NSEC_PER_SEC / rate; @@ -1497,6 +1497,8 @@ static void dwc3_get_properties(struct dwc3 *dwc) &dwc->fladj); device_property_read_u32(dev, "snps,ref-clock-period-ns", &dwc->ref_clk_per); + device_property_read_u32(dev, "snps,ref-clock-frequency-hz", + &dwc->ref_clk_freq); dwc->dis_metastability_quirk = device_property_read_bool(dev, "snps,dis_metastability_quirk"); diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index eb9c1efced05..00a792459fec 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -988,7 +988,8 @@ struct dwc3_scratchpad_array { * @regs: base address for our registers * @regs_size: address space size * @fladj: frame length adjustment - * @ref_clk_per: reference clock period configuration + * @ref_clk_per: reference clock period; deprecated in favor of @ref_clk_freq + * @ref_clk_freq: reference clock frequency to use if @ref_clk is missing * @irq_gadget: peripheral controller's IRQ number * @otg_irq: IRQ number for OTG IRQs * @current_otg_role: current role of operation while using the OTG block @@ -1171,6 +1172,7 @@ struct dwc3 { u32 fladj; u32 ref_clk_per; + u32 ref_clk_freq; u32 irq_gadget; u32 otg_irq; u32 current_otg_role;
This property allows setting the reference clock frequency properly for ACPI-based systems. It is not documented under dt-bindings, since it is not intended for use on DT-based systems. DT-based systems should use the clocks property instead. Frequency is preferred over period since it has greater precision when used in calculations. Signed-off-by: Sean Anderson <sean.anderson@seco.com> --- (no changes since v2) Changes in v2: - New drivers/usb/dwc3/core.c | 6 ++++-- drivers/usb/dwc3/core.h | 4 +++- 2 files changed, 7 insertions(+), 3 deletions(-)