deleted file mode 100644
@@ -1,28 +0,0 @@
-STMicroelectronics STPMIC1 Onkey
-
-Required properties:
-
-- compatible = "st,stpmic1-onkey";
-- interrupts: interrupt line to use
-- interrupt-names = "onkey-falling", "onkey-rising"
- onkey-falling: happens when onkey is pressed; IT_PONKEY_F of pmic
- onkey-rising: happens when onkey is released; IT_PONKEY_R of pmic
-
-Optional properties:
-
-- st,onkey-clear-cc-flag: onkey is able power on after an
- over-current shutdown event.
-- st,onkey-pu-inactive: onkey pull up is not active
-- power-off-time-sec: Duration in seconds which the key should be kept
- pressed for device to power off automatically (from 1 to 16 seconds).
- see See Documentation/devicetree/bindings/input/input.yaml
-
-Example:
-
-onkey {
- compatible = "st,stpmic1-onkey";
- interrupt-parent = <&pmic>;
- interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- power-off-time-sec = <10>;
-};
deleted file mode 100644
@@ -1,61 +0,0 @@
-* STMicroelectronics STPMIC1 Power Management IC
-
-Required properties:
-- compatible: : "st,stpmic1"
-- reg: : The I2C slave address for the STPMIC1 chip.
-- interrupts: : The interrupt line the device is connected to.
-- #interrupt-cells: : Should be 1.
-- interrupt-controller: : Marks the device node as an interrupt controller.
- Interrupt numbers are defined at
- dt-bindings/mfd/st,stpmic1.h.
-
-STPMIC1 consists in a varied group of sub-devices.
-Each sub-device binding is be described in own documentation file.
-
-Device Description
------- ------------
-st,stpmic1-onkey : Power on key, see ../input/st,stpmic1-onkey.txt
-st,stpmic1-regulators : Regulators, see ../regulator/st,stpmic1-regulator.txt
-st,stpmic1-wdt : Watchdog, see ../watchdog/st,stpmic1-wdt.txt
-
-Example:
-
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-pmic: pmic@33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupt-parent = <&gpioa>;
- interrupts = <0 2>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- power-off-time-sec = <10>;
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- };
-
- regulators {
- compatible = "st,stpmic1-regulators";
-
- vdd_core: buck1 {
- regulator-name = "vdd_core";
- regulator-boot-on;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1200000>;
- };
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-pull-down;
- };
- };
new file mode 100644
@@ -0,0 +1,339 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stpmic1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectonics STPMIC1 Power Management IC bindings
+
+description: STMicroelectronics STPMIC1 Power Management IC
+
+maintainers:
+ - pascal Paillet <p.paillet@st.com>
+
+properties:
+ compatible:
+ const: st,stpmic1
+
+ reg:
+ const: 0x33
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+ interrupt-controller: true
+
+ onkey:
+ type: object
+
+ allOf:
+ - $ref: ../input/input.yaml
+
+ properties:
+ compatible:
+ const: st,stpmic1-onkey
+
+ interrupts:
+ items:
+ - description: onkey-falling, happens when onkey is pressed. IT_PONKEY_F of pmic
+ - description: onkey-rising, happens when onkey is released. IT_PONKEY_R of pmic
+
+ interrupt-names:
+ items:
+ - const: onkey-falling
+ - const: onkey-rising
+
+ st,onkey-clear-cc-flag:
+ description: onkey is able power on after an over-current shutdown event.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ st,onkey-pu-inactive:
+ description: onkey pull up is not active
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ power-off-time-sec:
+ minimum: 1
+ maximum: 16
+
+ required:
+ - compatible
+ - interrupts
+ - interrupt-names
+
+ additionalProperties: false
+
+ watchdog:
+ type: object
+
+ allOf:
+ - $ref: ../watchdog/watchdog.yaml
+
+ properties:
+ compatible:
+ const: st,stpmic1-wdt
+
+ timeout-sec: true
+
+ required:
+ - compatible
+
+ additionalProperties: false
+
+ regulators:
+ type: object
+
+ description: |
+ Available Regulators in STPMIC1 device are:
+ - buck1 for Buck BUCK1
+ - buck2 for Buck BUCK2
+ - buck3 for Buck BUCK3
+ - buck4 for Buck BUCK4
+ - ldo1 for LDO LDO1
+ - ldo2 for LDO LDO2
+ - ldo3 for LDO LDO3
+ - ldo4 for LDO LDO4
+ - ldo5 for LDO LDO5
+ - ldo6 for LDO LDO6
+ - vref_ddr for LDO Vref DDR
+ - boost for Buck BOOST
+ - pwr_sw1 for VBUS_OTG switch
+ - pwr_sw2 for SW_OUT switch
+ Switches are fixed voltage regulators with only enable/disable capability.
+
+ properties:
+ compatible:
+ const: st,stpmic1-regulators
+
+ ldo3:
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ st,mask-reset:
+ description: mask reset for this regulator,
+ the regulator configuration is maintained during pmic reset.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+ regulator-min-microvolt: true
+ regulator-max-microvolt: true
+ regulator-allow-bypass: true
+ regulator-over-current-protection: true
+
+ additionalProperties: false
+
+ ldo4:
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ st,mask-reset:
+ description: mask reset for this regulator,
+ the regulator configuration is maintained during pmic reset.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+ regulator-over-current-protection: true
+
+ additionalProperties: false
+
+ vref_ddr:
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ st,mask-reset:
+ description: mask reset for this regulator,
+ the regulator configuration is maintained during pmic reset.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+
+ additionalProperties: false
+
+ boost:
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ st,mask-reset:
+ description: mask reset for this regulator,
+ the regulator configuration is maintained during pmic reset.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+ regulator-over-current-protection: true
+
+ additionalProperties: false
+
+ patternProperties:
+ "^(buck[1-4]|ldo[1-6]|boost|pwr_sw[1-2])-supply$":
+ description: STPMIC1 voltage regulators supplies
+
+ "^(buck[1-4]|ldo[1-6]|boost|vref_ddr|pwr_sw[1-2])$":
+ allOf:
+ - $ref: ../regulator/regulator.yaml
+
+ "^ldo[1-2,5-6]$":
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ st,mask-reset:
+ description: mask reset for this regulator,
+ the regulator configuration is maintained during pmic reset.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+ regulator-min-microvolt: true
+ regulator-max-microvolt: true
+ regulator-over-current-protection: true
+ regulator-enable-ramp-delay: true
+
+ additionalProperties: false
+
+ "^buck[1-4]$":
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ st,mask-reset:
+ description: mask reset for this regulator,
+ the regulator configuration is maintained during pmic reset.
+ $ref: /schemas/types.yaml#/definitions/flag
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+ regulator-min-microvolt: true
+ regulator-max-microvolt: true
+ regulator-initial-mode: true
+ regulator-pull-down: true
+ regulator-over-current-protection: true
+ regulator-enable-ramp-delay: true
+
+ additionalProperties: false
+
+ "^pwr_sw[1-2]$":
+ type: object
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ regulator-name: true
+ regulator-boot-on: true
+ regulator-always-on: true
+ regulator-over-current-protection: true
+ regulator-active-discharge: true
+
+ additionalProperties: false
+
+ required:
+ - compatible
+
+ additionalProperties: false
+
+ additionalProperties: false
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - "#interrupt-cells"
+ - interrupt-controller
+
+examples:
+ - |
+ #include <dt-bindings/mfd/st,stpmic1.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupt-parent = <&gpioa>;
+ interrupts = <0 2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ };
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo6-supply = <&v3v3>;
+
+ buck1 {
+ regulator-name = "vdd_core";
+ interrupts = <IT_CURLIM_BUCK1 0>;
+ st,mask-reset;
+ regulator-boot-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-pull-down;
+ };
+
+ buck4 {
+ regulator-name = "v3v3";
+ interrupts = <IT_CURLIM_BUCK4 0>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo6 {
+ regulator-name = "v1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-over-current-protection;
+ };
+ };
+ };
+ };
+
+...
deleted file mode 100644
@@ -1,64 +0,0 @@
-STMicroelectronics STPMIC1 Voltage regulators
-
-Regulator Nodes are optional depending on needs.
-
-Available Regulators in STPMIC1 device are:
- - buck1 for Buck BUCK1
- - buck2 for Buck BUCK2
- - buck3 for Buck BUCK3
- - buck4 for Buck BUCK4
- - ldo1 for LDO LDO1
- - ldo2 for LDO LDO2
- - ldo3 for LDO LDO3
- - ldo4 for LDO LDO4
- - ldo5 for LDO LDO5
- - ldo6 for LDO LDO6
- - vref_ddr for LDO Vref DDR
- - boost for Buck BOOST
- - pwr_sw1 for VBUS_OTG switch
- - pwr_sw2 for SW_OUT switch
-
-Switches are fixed voltage regulators with only enable/disable capability.
-
-Optional properties:
-- st,mask-reset: mask reset for this regulator: the regulator configuration
- is maintained during pmic reset.
-- regulator-over-current-protection:
- if set, all regulators are switched off in case of over-current detection
- on this regulator,
- if not set, the driver only sends an over-current event.
-- interrupts: index of current limit detection interrupt
-- <regulator>-supply: phandle to the parent supply/regulator node
- each regulator supply can be described except vref_ddr.
-- regulator-active-discharge: can be used on pwr_sw1 and pwr_sw2.
-
-Example:
-regulators {
- compatible = "st,stpmic1-regulators";
-
- ldo6-supply = <&v3v3>;
-
- vdd_core: buck1 {
- regulator-name = "vdd_core";
- interrupts = <IT_CURLIM_BUCK1 0>;
- st,mask-reset;
- regulator-pull-down;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1200000>;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- interrupts = <IT_CURLIM_BUCK4 0>;
-
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-over-current-protection;
- };
-};
deleted file mode 100644
@@ -1,11 +0,0 @@
-STMicroelectronics STPMIC1 Watchdog
-
-Required properties:
-
-- compatible : should be "st,stpmic1-wdt"
-
-Example:
-
-watchdog {
- compatible = "st,stpmic1-wdt";
-};
Convert stpmic1 bindings to json-schema. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> --- version 5: - move $ref regulator.yaml under a patternProperties - move remain fixed strings under properties field version 4: - move on uppder node $ref: ../regulator/regulator.yaml - move fixed strings under properties field - remove unneeded () in patternProperties - keep ldo3 separate from other ldo properties Note: - 'st,mask-reset' property stay in each subnode, I don't find the syntax to avoid dupliquate it. - ldo6-supply and all possible *-supply are describe by this regular expression: ^(buck[1-4]|ldo[1-6]|boost|pwr_sw[1-2])-supply$": version 3: - put $ref under allOf keyword - for each regulator node add the list of supported regulator properties .../devicetree/bindings/input/st,stpmic1-onkey.txt | 28 -- .../devicetree/bindings/mfd/st,stpmic1.txt | 61 ---- .../devicetree/bindings/mfd/st,stpmic1.yaml | 339 +++++++++++++++++++++ .../bindings/regulator/st,stpmic1-regulator.txt | 64 ---- .../bindings/watchdog/st,stpmic1-wdt.txt | 11 - 5 files changed, 339 insertions(+), 164 deletions(-) delete mode 100644 Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt delete mode 100644 Documentation/devicetree/bindings/mfd/st,stpmic1.txt create mode 100644 Documentation/devicetree/bindings/mfd/st,stpmic1.yaml delete mode 100644 Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt delete mode 100644 Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt