| Message ID | 1426080326-14764-1-git-send-email-michal.kazior@tieto.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Kalle Valo |
| Headers | show |
On Wed, 2015-03-11 at 14:25 +0100, Michal Kazior wrote: > NativeWifi tx mode expects QoS Data frames to be > delivered as Data frames with QoS part (e.g. tid) > being delievered out-of-band in fw tx command. > > The QoS bit wasn't stripped before submitting to > firmware. > > Stripping fixes two known problems: > > * qca6174 IOT with some APs, e.g. > Cisco AIR-AP 1252 (which would crash after > ath10k association). Some ath9k APs would > crash as well. It would probably be interesting to figure out why and fix that - this is clearly a major issue. johannes -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 11 March 2015 at 17:22, Johannes Berg <johannes@sipsolutions.net> wrote: > On Wed, 2015-03-11 at 14:25 +0100, Michal Kazior wrote: >> NativeWifi tx mode expects QoS Data frames to be >> delivered as Data frames with QoS part (e.g. tid) >> being delievered out-of-band in fw tx command. >> >> The QoS bit wasn't stripped before submitting to >> firmware. >> >> Stripping fixes two known problems: >> >> * qca6174 IOT with some APs, e.g. >> Cisco AIR-AP 1252 (which would crash after >> ath10k association). Some ath9k APs would >> crash as well. > > It would probably be interesting to figure out why and fix that - this > is clearly a major issue. Good point. The patch was originally just a small fix for sniffing but it happened to fix the IOT problem that we started seeing with the new chip fw as well. I believe that if 11n was disabled on APs the problem did not reproduce. I think ath9k was crashing somewhere along the BA session teardown (as per kernel call trace). The ath9k codebase from what I know was rather old (some custom 3.4 fork) so perhaps it was a race of some sort that has been fixed long since. I'll try to get some sniff logs and take a look at this more closely. Micha? -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Michal Kazior <michal.kazior@tieto.com> writes: > NativeWifi tx mode expects QoS Data frames to be > delivered as Data frames with QoS part (e.g. tid) > being delievered out-of-band in fw tx command. > > The QoS bit wasn't stripped before submitting to > firmware. > > Stripping fixes two known problems: > > * qca6174 IOT with some APs, e.g. > Cisco AIR-AP 1252 (which would crash after > ath10k association). Some ath9k APs would > crash as well. > > * sniffing own tx frames via radiotap because, > e.g. wireshark was seeing QoS bit set but > since QoS Control was stripped in ath10k it > would parse beginning of LLC/SNAP > >>From debugability point of view this removes the > ability to distinguish QoS from non-QoS frames > when sniffing own tx via radiotap. On the other > hand frames can be now parsed correctly without > special software modification. > > Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Thanks, applied.
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index 1138f4f..625e2cb 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -2463,16 +2463,15 @@ static void ath10k_tx_h_nwifi(struct ieee80211_hw *hw, struct sk_buff *skb) skb->data, (void *)qos_ctl - (void *)skb->data); skb_pull(skb, IEEE80211_QOS_CTL_LEN); - /* Fw/Hw generates a corrupted QoS Control Field for QoS NullFunc - * frames. Powersave is handled by the fw/hw so QoS NyllFunc frames are - * used only for CQM purposes (e.g. hostapd station keepalive ping) so - * it is safe to downgrade to NullFunc. + /* Some firmware revisions don't handle sending QoS NullFunc well. + * These frames are mainly used for CQM purposes so it doesn't really + * matter whether QoS NullFunc or NullFunc are sent. */ hdr = (void *)skb->data; - if (ieee80211_is_qos_nullfunc(hdr->frame_control)) { - hdr->frame_control &= ~__cpu_to_le16(IEEE80211_STYPE_QOS_DATA); + if (ieee80211_is_qos_nullfunc(hdr->frame_control)) cb->htt.tid = HTT_DATA_TX_EXT_TID_NON_QOS_MCAST_BCAST; - } + + hdr->frame_control &= ~__cpu_to_le16(IEEE80211_STYPE_QOS_DATA); } static void ath10k_tx_h_add_p2p_noa_ie(struct ath10k *ar,
NativeWifi tx mode expects QoS Data frames to be delivered as Data frames with QoS part (e.g. tid) being delievered out-of-band in fw tx command. The QoS bit wasn't stripped before submitting to firmware. Stripping fixes two known problems: * qca6174 IOT with some APs, e.g. Cisco AIR-AP 1252 (which would crash after ath10k association). Some ath9k APs would crash as well. * sniffing own tx frames via radiotap because, e.g. wireshark was seeing QoS bit set but since QoS Control was stripped in ath10k it would parse beginning of LLC/SNAP From debugability point of view this removes the ability to distinguish QoS from non-QoS frames when sniffing own tx via radiotap. On the other hand frames can be now parsed correctly without special software modification. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> --- drivers/net/wireless/ath/ath10k/mac.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-)