@@ -3312,7 +3312,7 @@ static int ath6kl_cfg80211_sscan_start(struct wiphy *wiphy,
}
/* fw uses seconds, also make sure that it's >0 */
- interval = max_t(u16, 1, request->interval / 1000);
+ interval = max_t(u16, 1, request->scan_plans[0].interval);
ath6kl_wmi_scanparams_cmd(ar->wmi, vif->fw_vif_idx,
interval, interval,
@@ -1242,7 +1242,6 @@ static ssize_t iwl_dbgfs_netdetect_write(struct iwl_mvm *mvm, char *buf,
mvm->nd_config->n_channels = 11;
mvm->nd_config->scan_width = NL80211_BSS_CHAN_WIDTH_20;
- mvm->nd_config->interval = 5;
mvm->nd_config->min_rssi_thold = -80;
for (i = 0; i < mvm->nd_config->n_channels; i++)
mvm->nd_config->channels[i] = &mvm->nvm_data->channels[i];
@@ -1278,14 +1277,26 @@ static ssize_t iwl_dbgfs_netdetect_write(struct iwl_mvm *mvm, char *buf,
mvm->nd_config->n_match_sets++;
}
+ mvm->nd_config->scan_plans =
+ kzalloc(sizeof(*mvm->nd_config->scan_plans), GFP_KERNEL);
+ if (!mvm->nd_config->scan_plans) {
+ ret = -ENOMEM;
+ goto out_free;
+ }
+
+ mvm->nd_config->scan_plans[0].interval = 5;
+
ret = count;
if (mvm->nd_config->n_match_sets)
goto out;
out_free:
- if (mvm->nd_config)
+ if (mvm->nd_config) {
kfree(mvm->nd_config->match_sets);
+ kfree(mvm->nd_config->scan_plans);
+ }
+
kfree(mvm->nd_config);
mvm->nd_config = NULL;
out:
@@ -617,6 +617,7 @@ static void iwl_op_mode_mvm_stop(struct iwl_op_mode *op_mode)
kfree(mvm->d3_resume_sram);
if (mvm->nd_config) {
kfree(mvm->nd_config->match_sets);
+ kfree(mvm->nd_config->scan_plans);
kfree(mvm->nd_config);
mvm->nd_config = NULL;
}
@@ -1273,12 +1273,12 @@ int iwl_mvm_sched_scan_start(struct iwl_mvm *mvm,
params.type = iwl_mvm_get_scan_type(mvm, vif, ¶ms);
- if (req->interval > U16_MAX) {
+ if (req->scan_plans[0].interval > U16_MAX) {
IWL_DEBUG_SCAN(mvm,
"interval value is > 16-bits, set to max possible\n");
params.interval = U16_MAX;
} else {
- params.interval = req->interval / MSEC_PER_SEC;
+ params.interval = req->scan_plans[0].interval;
}
/* In theory, LMAC scans can handle a 32-bit delay, but since
@@ -350,7 +350,8 @@ int wl1271_scan_sched_scan_config(struct wl1271 *wl,
cfg->bss_type = SCAN_BSS_TYPE_ANY;
/* currently NL80211 supports only a single interval */
for (i = 0; i < SCAN_MAX_CYCLE_INTERVALS; i++)
- cfg->intervals[i] = cpu_to_le32(req->interval);
+ cfg->intervals[i] = cpu_to_le32(req->scan_plans[0].interval *
+ MSEC_PER_SEC);
cfg->ssid_len = 0;
ret = wlcore_scan_sched_scan_ssid_list(wl, wlvif, req);
@@ -228,13 +228,15 @@ int wl18xx_scan_sched_scan_config(struct wl1271 *wl,
wl18xx_adjust_channels(cmd, cmd_channels);
if (c->num_short_intervals && c->long_interval &&
- c->long_interval > req->interval) {
- cmd->short_cycles_msec = cpu_to_le16(req->interval);
+ c->long_interval > req->scan_plans[0].interval * MSEC_PER_SEC) {
+ cmd->short_cycles_msec =
+ cpu_to_le16(req->scan_plans[0].interval * MSEC_PER_SEC);
cmd->long_cycles_msec = cpu_to_le16(c->long_interval);
cmd->short_cycles_count = c->num_short_intervals;
} else {
cmd->short_cycles_msec = 0;
- cmd->long_cycles_msec = cpu_to_le16(req->interval);
+ cmd->long_cycles_msec =
+ cpu_to_le16(req->scan_plans[0].interval * MSEC_PER_SEC);
cmd->short_cycles_count = 0;
}
wl1271_debug(DEBUG_SCAN, "short_interval: %d, long_interval: %d, num_short: %d",
@@ -5,6 +5,7 @@
*
* Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
* Copyright 2013-2014 Intel Mobile Communications GmbH
+ * Copyright 2015 Intel Deutschland GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -1501,13 +1502,26 @@ struct cfg80211_match_set {
};
/**
+ * struct cfg80211_sched_scan_plan - scan plan for scheduled scan
+ *
+ * @interval: interval between scheduled scan iterations. In seconds.
+ * @iterations: number of scan iterations in this scan plan. Zero means
+ * infinite loop.
+ * The last scan plan will always have this parameter set to zero,
+ * all other scan plans will have a finite number of iterations.
+ */
+struct cfg80211_sched_scan_plan {
+ u32 interval;
+ u32 iterations;
+};
+
+/**
* struct cfg80211_sched_scan_request - scheduled scan request description
*
* @ssids: SSIDs to scan for (passed in the probe_reqs in active scans)
* @n_ssids: number of SSIDs
* @n_channels: total number of channels to scan
* @scan_width: channel width for scanning
- * @interval: interval between each scheduled scan cycle
* @ie: optional information element(s) to add into Probe Request or %NULL
* @ie_len: length of ie in octets
* @flags: bit field of flags controlling operation
@@ -1526,6 +1540,9 @@ struct cfg80211_match_set {
* @mac_addr_mask: MAC address mask used with randomisation, bits that
* are 0 in the mask should be randomised, bits that are 1 should
* be taken from the @mac_addr
+ * @scan_plans: scan plans to be executed in this scheduled scan. Lowest
+ * index must be executed first.
+ * @n_scan_plans: number of scan plans, at least 1.
* @rcu_head: RCU callback used to free the struct
* @owner_nlportid: netlink portid of owner (if this should is a request
* owned by a particular socket)
@@ -1539,7 +1556,6 @@ struct cfg80211_sched_scan_request {
int n_ssids;
u32 n_channels;
enum nl80211_bss_scan_width scan_width;
- u32 interval;
const u8 *ie;
size_t ie_len;
u32 flags;
@@ -1547,6 +1563,8 @@ struct cfg80211_sched_scan_request {
int n_match_sets;
s32 min_rssi_thold;
u32 delay;
+ struct cfg80211_sched_scan_plan *scan_plans;
+ int n_scan_plans;
u8 mac_addr[ETH_ALEN] __aligned(2);
u8 mac_addr_mask[ETH_ALEN] __aligned(2);
@@ -3056,6 +3074,12 @@ struct wiphy_vendor_command {
* include fixed IEs like supported rates
* @max_sched_scan_ie_len: same as max_scan_ie_len, but for scheduled
* scans
+ * @max_sched_scan_plans: maximum number of scan plans (scan interval and number
+ * of iterations) for scheduled scan supported by the device.
+ * @max_sched_scan_plan_interval: maximum interval (in seconds) for a
+ * single scan plan supported by the device.
+ * @max_sched_scan_plan_iterations: maximum number of iterations for a single
+ * scan plan supported by the device.
* @coverage_class: current coverage class
* @fw_version: firmware version for ethtool reporting
* @hw_version: hardware version for ethtool reporting
@@ -3163,6 +3187,9 @@ struct wiphy {
u8 max_match_sets;
u16 max_scan_ie_len;
u16 max_sched_scan_ie_len;
+ u32 max_sched_scan_plans;
+ u32 max_sched_scan_plan_interval;
+ u32 max_sched_scan_plan_iterations;
int n_cipher_suites;
const u32 *cipher_suites;
@@ -10,6 +10,7 @@
* Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
+ * Copyright 2015 Intel Deutschland GmbH
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
@@ -328,7 +329,15 @@
* partial scan results may be available
*
* @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
- * intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL.
+ * intervals and certain number of cycles, as specified by
+ * %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is
+ * not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified,
+ * scheduled scan will run in an infinite loop with the specified interval.
+ * These attributes are mutually exculsive,
+ * i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if
+ * NL80211_ATTR_SCHED_SCAN_PLANS is defined.
+ * If for some reason scheduled scan is aborted by the driver, all scan
+ * plans are canceled (including scan plans that did not start yet).
* Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
* are passed, they are used in the probe requests. For
* broadcast, a broadcast SSID must be passed (ie. an empty
@@ -1761,6 +1770,19 @@ enum nl80211_commands {
* @NL80211_ATTR_REG_INDOOR: flag attribute, if set indicates that the device
* is operating in an indoor environment.
*
+ * @NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS: maximum number of scan plans for
+ * scheduled scan supported by the device (u32), a wiphy attribute.
+ * @NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL: maximum interval (in seconds) for
+ * a scan plan (u32), a wiphy attribute.
+ * @NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS: maximum number of iterations in
+ * a scan plan (u32), a wiphy attribute.
+ * @NL80211_ATTR_SCHED_SCAN_PLANS: a list of scan plans for scheduled scan.
+ * Each scan plan defines the number of scan iterations and the interval
+ * between scans. The last scan plan will always run infinitely,
+ * thus it must not specify the number of iterations, only the interval
+ * between scans. The scan plans are executed sequentially.
+ * Each scan plan is a nested attribute of &enum nl80211_sched_scan_plan.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -2130,6 +2152,11 @@ enum nl80211_attrs {
NL80211_ATTR_REG_INDOOR,
+ NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS,
+ NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL,
+ NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS,
+ NL80211_ATTR_SCHED_SCAN_PLANS,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -4589,4 +4616,28 @@ enum nl80211_tdls_peer_capability {
NL80211_TDLS_PEER_WMM = 1<<2,
};
+/**
+ * enum nl80211_sched_scan_plan - scanning plan for scheduled scan
+ * @__NL80211_SCHED_SCAN_PLAN_INVALID: attribute number 0 is reserved
+ * @NL80211_SCHED_SCAN_PLAN_INTERVAL: interval between scan iterations. In
+ * seconds (u32).
+ * @NL80211_SCHED_SCAN_PLAN_ITERATIONS: number of scan iterations in this
+ * scan plan (u32). The last scan plan must not specify this attribute
+ * because it will run infinitely. A value of zero is invalid as it will
+ * make the scan plan meaningless.
+ * @NL80211_SCHED_SCAN_PLAN_MAX: highest scheduled scan plan attribute number
+ * currently defined
+ * @__NL80211_SCHED_SCAN_PLAN_AFTER_LAST: internal use
+ */
+enum nl80211_sched_scan_plan {
+ __NL80211_SCHED_SCAN_PLAN_INVALID,
+ NL80211_SCHED_SCAN_PLAN_INTERVAL,
+ NL80211_SCHED_SCAN_PLAN_ITERATIONS,
+
+ /* keep last */
+ __NL80211_SCHED_SCAN_PLAN_AFTER_LAST,
+ NL80211_SCHED_SCAN_PLAN_MAX =
+ __NL80211_SCHED_SCAN_PLAN_AFTER_LAST - 1
+};
+
#endif /* __LINUX_NL80211_H */
@@ -461,6 +461,9 @@ use_default_name:
rdev->wiphy.max_num_csa_counters = 1;
+ rdev->wiphy.max_sched_scan_plans = 1;
+ rdev->wiphy.max_sched_scan_plan_interval = U32_MAX;
+
return &rdev->wiphy;
}
EXPORT_SYMBOL(wiphy_new_nm);
@@ -479,6 +479,12 @@ nl80211_match_policy[NL80211_SCHED_SCAN_MATCH_ATTR_MAX + 1] = {
[NL80211_SCHED_SCAN_MATCH_ATTR_RSSI] = { .type = NLA_U32 },
};
+static const struct nla_policy
+nl80211_plan_policy[NL80211_SCHED_SCAN_PLAN_MAX + 1] = {
+ [NL80211_SCHED_SCAN_PLAN_INTERVAL] = { .type = NLA_U32 },
+ [NL80211_SCHED_SCAN_PLAN_ITERATIONS] = { .type = NLA_U32 },
+};
+
static int nl80211_prepare_wdev_dump(struct sk_buff *skb,
struct netlink_callback *cb,
struct cfg80211_registered_device **rdev,
@@ -1304,7 +1310,13 @@ static int nl80211_send_wiphy(struct cfg80211_registered_device *rdev,
nla_put_u16(msg, NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN,
rdev->wiphy.max_sched_scan_ie_len) ||
nla_put_u8(msg, NL80211_ATTR_MAX_MATCH_SETS,
- rdev->wiphy.max_match_sets))
+ rdev->wiphy.max_match_sets) ||
+ nla_put_u32(msg, NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS,
+ rdev->wiphy.max_sched_scan_plans) ||
+ nla_put_u32(msg, NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL,
+ rdev->wiphy.max_sched_scan_plan_interval) ||
+ nla_put_u32(msg, NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS,
+ rdev->wiphy.max_sched_scan_plan_iterations))
goto nla_put_failure;
if ((rdev->wiphy.flags & WIPHY_FLAG_IBSS_RSN) &&
@@ -5974,14 +5986,100 @@ static int nl80211_trigger_scan(struct sk_buff *skb, struct genl_info *info)
return err;
}
+static int
+nl80211_parse_sched_scan_plans(struct wiphy *wiphy, int n_plans,
+ struct cfg80211_sched_scan_request *request,
+ struct nlattr **attrs)
+{
+ int tmp, err, i = 0;
+ struct nlattr *attr;
+
+ if (!attrs[NL80211_ATTR_SCHED_SCAN_PLANS]) {
+ u32 interval;
+
+ /*
+ * If scan plans are not specified,
+ * %NL80211_ATTR_SCHED_SCAN_INTERVAL must be specified. In this
+ * case one scan plan will be set with the specified scan
+ * interval and infinite number of iterations.
+ */
+ if (!attrs[NL80211_ATTR_SCHED_SCAN_INTERVAL])
+ return -EINVAL;
+
+ interval = nla_get_u32(attrs[NL80211_ATTR_SCHED_SCAN_INTERVAL]);
+ if (!interval)
+ return -EINVAL;
+
+ request->scan_plans[0].interval =
+ DIV_ROUND_UP(interval, MSEC_PER_SEC);
+ if (!request->scan_plans[0].interval)
+ return -EINVAL;
+
+ if (request->scan_plans[0].interval >
+ wiphy->max_sched_scan_plan_interval)
+ request->scan_plans[0].interval =
+ wiphy->max_sched_scan_plan_interval;
+
+ return 0;
+ }
+
+ nla_for_each_nested(attr, attrs[NL80211_ATTR_SCHED_SCAN_PLANS], tmp) {
+ struct nlattr *plan[NL80211_SCHED_SCAN_PLAN_MAX + 1];
+
+ if (WARN_ON(i >= n_plans))
+ return -EINVAL;
+
+ err = nla_parse(plan, NL80211_SCHED_SCAN_PLAN_MAX,
+ nla_data(attr), nla_len(attr),
+ nl80211_plan_policy);
+ if (err)
+ return err;
+
+ if (!plan[NL80211_SCHED_SCAN_PLAN_INTERVAL])
+ return -EINVAL;
+
+ request->scan_plans[i].interval =
+ nla_get_u32(plan[NL80211_SCHED_SCAN_PLAN_INTERVAL]);
+ if (!request->scan_plans[i].interval ||
+ request->scan_plans[i].interval >
+ wiphy->max_sched_scan_plan_interval)
+ return -EINVAL;
+
+ if (plan[NL80211_SCHED_SCAN_PLAN_ITERATIONS]) {
+ request->scan_plans[i].iterations =
+ nla_get_u32(plan[NL80211_SCHED_SCAN_PLAN_ITERATIONS]);
+ if (!request->scan_plans[i].iterations ||
+ (request->scan_plans[i].iterations >
+ wiphy->max_sched_scan_plan_iterations))
+ return -EINVAL;
+ } else if (i < n_plans - 1) {
+ /*
+ * All scan plans but the last one must specify
+ * a finite number of iterations
+ */
+ return -EINVAL;
+ }
+
+ i++;
+ }
+
+ /*
+ * The last scan plan must not specify the number of
+ * iterations, it is supposed to run infinitely
+ */
+ if (request->scan_plans[n_plans - 1].iterations)
+ return -EINVAL;
+
+ return 0;
+}
+
static struct cfg80211_sched_scan_request *
nl80211_parse_sched_scan(struct wiphy *wiphy, struct wireless_dev *wdev,
struct nlattr **attrs)
{
struct cfg80211_sched_scan_request *request;
struct nlattr *attr;
- int err, tmp, n_ssids = 0, n_match_sets = 0, n_channels, i;
- u32 interval;
+ int err, tmp, n_ssids = 0, n_match_sets = 0, n_channels, i, n_plans = 0;
enum ieee80211_band band;
size_t ie_len;
struct nlattr *tb[NL80211_SCHED_SCAN_MATCH_ATTR_MAX + 1];
@@ -5990,13 +6088,6 @@ nl80211_parse_sched_scan(struct wiphy *wiphy, struct wireless_dev *wdev,
if (!is_valid_ie_attr(attrs[NL80211_ATTR_IE]))
return ERR_PTR(-EINVAL);
- if (!attrs[NL80211_ATTR_SCHED_SCAN_INTERVAL])
- return ERR_PTR(-EINVAL);
-
- interval = nla_get_u32(attrs[NL80211_ATTR_SCHED_SCAN_INTERVAL]);
- if (interval == 0)
- return ERR_PTR(-EINVAL);
-
if (attrs[NL80211_ATTR_SCAN_FREQUENCIES]) {
n_channels = validate_scan_freqs(
attrs[NL80211_ATTR_SCAN_FREQUENCIES]);
@@ -6060,9 +6151,37 @@ nl80211_parse_sched_scan(struct wiphy *wiphy, struct wireless_dev *wdev,
if (ie_len > wiphy->max_sched_scan_ie_len)
return ERR_PTR(-EINVAL);
+ if (attrs[NL80211_ATTR_SCHED_SCAN_PLANS]) {
+ /*
+ * NL80211_ATTR_SCHED_SCAN_INTERVAL must not be specified since
+ * each scan plan already specifies its own interval
+ */
+ if (attrs[NL80211_ATTR_SCHED_SCAN_INTERVAL])
+ return ERR_PTR(-EINVAL);
+
+ nla_for_each_nested(attr,
+ attrs[NL80211_ATTR_SCHED_SCAN_PLANS], tmp)
+ n_plans++;
+ } else {
+ /*
+ * The scan interval attribute is kept for backward
+ * compatibility. If no scan plans are specified and sched scan
+ * interval is specified, one scan plan will be set with this
+ * scan interval and infinite number of iterations.
+ */
+ if (!attrs[NL80211_ATTR_SCHED_SCAN_INTERVAL])
+ return ERR_PTR(-EINVAL);
+
+ n_plans = 1;
+ }
+
+ if (!n_plans || n_plans > wiphy->max_sched_scan_plans)
+ return ERR_PTR(-EINVAL);
+
request = kzalloc(sizeof(*request)
+ sizeof(*request->ssids) * n_ssids
+ sizeof(*request->match_sets) * n_match_sets
+ + sizeof(*request->scan_plans) * n_plans
+ sizeof(*request->channels) * n_channels
+ ie_len, GFP_KERNEL);
if (!request)
@@ -6090,6 +6209,18 @@ nl80211_parse_sched_scan(struct wiphy *wiphy, struct wireless_dev *wdev,
}
request->n_match_sets = n_match_sets;
+ if (n_match_sets)
+ request->scan_plans = (void *)(request->match_sets +
+ n_match_sets);
+ else if (request->ie)
+ request->scan_plans = (void *)(request->ie + ie_len);
+ else if (n_ssids)
+ request->scan_plans = (void *)(request->ssids + n_ssids);
+ else
+ request->scan_plans = (void *)(request->channels + n_channels);
+
+ request->n_scan_plans = n_plans;
+
i = 0;
if (attrs[NL80211_ATTR_SCAN_FREQUENCIES]) {
/* user specified, bail out if channel not found */
@@ -6252,7 +6383,10 @@ nl80211_parse_sched_scan(struct wiphy *wiphy, struct wireless_dev *wdev,
request->delay =
nla_get_u32(attrs[NL80211_ATTR_SCHED_SCAN_DELAY]);
- request->interval = interval;
+ err = nl80211_parse_sched_scan_plans(wiphy, n_plans, request, attrs);
+ if (err)
+ goto out_free;
+
request->scan_start = jiffies;
return request;
@@ -8845,7 +8979,7 @@ static int nl80211_send_wowlan_tcp(struct sk_buff *msg,
static int nl80211_send_wowlan_nd(struct sk_buff *msg,
struct cfg80211_sched_scan_request *req)
{
- struct nlattr *nd, *freqs, *matches, *match;
+ struct nlattr *nd, *freqs, *matches, *match, *scan_plans, *scan_plan;
int i;
if (!req)
@@ -8855,7 +8989,9 @@ static int nl80211_send_wowlan_nd(struct sk_buff *msg,
if (!nd)
return -ENOBUFS;
- if (nla_put_u32(msg, NL80211_ATTR_SCHED_SCAN_INTERVAL, req->interval))
+ if (req->n_scan_plans == 1 &&
+ nla_put_u32(msg, NL80211_ATTR_SCHED_SCAN_INTERVAL,
+ req->scan_plans[0].interval * 1000))
return -ENOBUFS;
if (nla_put_u32(msg, NL80211_ATTR_SCHED_SCAN_DELAY, req->delay))
@@ -8882,6 +9018,23 @@ static int nl80211_send_wowlan_nd(struct sk_buff *msg,
nla_nest_end(msg, matches);
}
+ scan_plans = nla_nest_start(msg, NL80211_ATTR_SCHED_SCAN_PLANS);
+ if (!scan_plans)
+ return -ENOBUFS;
+
+ for (i = 0; i < req->n_scan_plans; i++) {
+ scan_plan = nla_nest_start(msg, i + 1);
+ if (!scan_plan ||
+ nla_put_u32(msg, NL80211_SCHED_SCAN_PLAN_INTERVAL,
+ req->scan_plans[i].interval) ||
+ (req->scan_plans[i].iterations &&
+ nla_put_u32(msg, NL80211_SCHED_SCAN_PLAN_ITERATIONS,
+ req->scan_plans[i].iterations)))
+ return -ENOBUFS;
+ nla_nest_end(msg, scan_plan);
+ }
+ nla_nest_end(msg, scan_plans);
+
nla_nest_end(msg, nd);
return 0;
@@ -266,8 +266,7 @@ void __cfg80211_sched_scan_results(struct work_struct *wk)
spin_lock_bh(&rdev->bss_lock);
__cfg80211_bss_expire(rdev, request->scan_start);
spin_unlock_bh(&rdev->bss_lock);
- request->scan_start =
- jiffies + msecs_to_jiffies(request->interval);
+ request->scan_start = jiffies;
}
nl80211_send_sched_scan_results(rdev, request->dev);
}