@@ -1,3 +1,3 @@
obj-$(CONFIG_RTL8XXXU) += rtl8xxxu.o
-rtl8xxxu-y := rtl8xxxu_core.o rtl8xxxu_8192e.o
+rtl8xxxu-y := rtl8xxxu_core.o rtl8xxxu_8192e.o rtl8xxxu_8723b.o
@@ -1383,9 +1383,15 @@ int rtl8xxxu_init_phy_rf(struct rtl8xxxu_priv *priv,
int rtl8xxxu_init_phy_regs(struct rtl8xxxu_priv *priv,
struct rtl8xxxu_reg32val *array);
int rtl8xxxu_load_firmware(struct rtl8xxxu_priv *priv, char *fw_name);
+void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv);
void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv);
void rtl8xxxu_reset_8051(struct rtl8xxxu_priv *priv);
int rtl8xxxu_auto_llt_table(struct rtl8xxxu_priv *priv, u8 last_tx_page);
+void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start);
+int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv);
+int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv, struct h2c_cmd *h2c, int len);
+int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv);
+void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv);
void rtl8xxxu_gen2_config_channel(struct ieee80211_hw *hw);
void rtl8xxxu_gen2_usb_quirks(struct rtl8xxxu_priv *priv);
void rtl8xxxu_gen2_update_rate_mask(struct rtl8xxxu_priv *priv,
@@ -1400,3 +1406,4 @@ bool rtl8xxxu_gen2_simularity_compare(struct rtl8xxxu_priv *priv,
int result[][8], int c1, int c2);
extern struct rtl8xxxu_fileops rtl8192eu_fops;
+extern struct rtl8xxxu_fileops rtl8723bu_fops;
new file mode 100644
@@ -0,0 +1,1684 @@
+/*
+ * RTL8XXXU mac80211 USB driver - 8723b specific subdriver
+ *
+ * Copyright (c) 2014 - 2016 Jes Sorensen <Jes.Sorensen@redhat.com>
+ *
+ * Portions, notably calibration code:
+ * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
+ *
+ * This driver was written as a replacement for the vendor provided
+ * rtl8723au driver. As the Realtek 8xxx chips are very similar in
+ * their programming interface, I have started adding support for
+ * additional 8xxx chips like the 8192cu, 8188cus, etc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/list.h>
+#include <linux/usb.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/wireless.h>
+#include <linux/firmware.h>
+#include <linux/moduleparam.h>
+#include <net/mac80211.h>
+#include "rtl8xxxu.h"
+#include "rtl8xxxu_regs.h"
+
+static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = {
+ {0x02f, 0x30}, {0x035, 0x00}, {0x039, 0x08}, {0x04e, 0xe0},
+ {0x064, 0x00}, {0x067, 0x20}, {0x428, 0x0a}, {0x429, 0x10},
+ {0x430, 0x00}, {0x431, 0x00},
+ {0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05},
+ {0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05},
+ {0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01},
+ {0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00},
+ {0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f},
+ {0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00},
+ {0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f},
+ {0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66},
+ {0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff},
+ {0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2},
+ {0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3},
+ {0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4},
+ {0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4},
+ {0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a},
+ {0x516, 0x0a}, {0x525, 0x4f},
+ {0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50},
+ {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a},
+ {0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff},
+ {0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff},
+ {0x638, 0x50}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e},
+ {0x63f, 0x0e}, {0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00},
+ {0x652, 0xc8}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43},
+ {0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43},
+ {0x70a, 0x65}, {0x70b, 0x87}, {0x765, 0x18}, {0x76e, 0x04},
+ {0xffff, 0xff},
+};
+
+static struct rtl8xxxu_reg32val rtl8723b_phy_1t_init_table[] = {
+ {0x800, 0x80040000}, {0x804, 0x00000003},
+ {0x808, 0x0000fc00}, {0x80c, 0x0000000a},
+ {0x810, 0x10001331}, {0x814, 0x020c3d10},
+ {0x818, 0x02200385}, {0x81c, 0x00000000},
+ {0x820, 0x01000100}, {0x824, 0x00190204},
+ {0x828, 0x00000000}, {0x82c, 0x00000000},
+ {0x830, 0x00000000}, {0x834, 0x00000000},
+ {0x838, 0x00000000}, {0x83c, 0x00000000},
+ {0x840, 0x00010000}, {0x844, 0x00000000},
+ {0x848, 0x00000000}, {0x84c, 0x00000000},
+ {0x850, 0x00000000}, {0x854, 0x00000000},
+ {0x858, 0x569a11a9}, {0x85c, 0x01000014},
+ {0x860, 0x66f60110}, {0x864, 0x061f0649},
+ {0x868, 0x00000000}, {0x86c, 0x27272700},
+ {0x870, 0x07000760}, {0x874, 0x25004000},
+ {0x878, 0x00000808}, {0x87c, 0x00000000},
+ {0x880, 0xb0000c1c}, {0x884, 0x00000001},
+ {0x888, 0x00000000}, {0x88c, 0xccc000c0},
+ {0x890, 0x00000800}, {0x894, 0xfffffffe},
+ {0x898, 0x40302010}, {0x89c, 0x00706050},
+ {0x900, 0x00000000}, {0x904, 0x00000023},
+ {0x908, 0x00000000}, {0x90c, 0x81121111},
+ {0x910, 0x00000002}, {0x914, 0x00000201},
+ {0xa00, 0x00d047c8}, {0xa04, 0x80ff800c},
+ {0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f},
+ {0xa10, 0x9500bb78}, {0xa14, 0x1114d028},
+ {0xa18, 0x00881117}, {0xa1c, 0x89140f00},
+ {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317},
+ {0xa28, 0x00000204}, {0xa2c, 0x00d30000},
+ {0xa70, 0x101fbf00}, {0xa74, 0x00000007},
+ {0xa78, 0x00000900}, {0xa7c, 0x225b0606},
+ {0xa80, 0x21806490}, {0xb2c, 0x00000000},
+ {0xc00, 0x48071d40}, {0xc04, 0x03a05611},
+ {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c},
+ {0xc10, 0x08800000}, {0xc14, 0x40000100},
+ {0xc18, 0x08800000}, {0xc1c, 0x40000100},
+ {0xc20, 0x00000000}, {0xc24, 0x00000000},
+ {0xc28, 0x00000000}, {0xc2c, 0x00000000},
+ {0xc30, 0x69e9ac44}, {0xc34, 0x469652af},
+ {0xc38, 0x49795994}, {0xc3c, 0x0a97971c},
+ {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7},
+ {0xc48, 0xec020107}, {0xc4c, 0x007f037f},
+ {0xc50, 0x69553420}, {0xc54, 0x43bc0094},
+ {0xc58, 0x00013149}, {0xc5c, 0x00250492},
+ {0xc60, 0x00000000}, {0xc64, 0x7112848b},
+ {0xc68, 0x47c00bff}, {0xc6c, 0x00000036},
+ {0xc70, 0x2c7f000d}, {0xc74, 0x020610db},
+ {0xc78, 0x0000001f}, {0xc7c, 0x00b91612},
+ {0xc80, 0x390000e4}, {0xc84, 0x20f60000},
+ {0xc88, 0x40000100}, {0xc8c, 0x20200000},
+ {0xc90, 0x00020e1a}, {0xc94, 0x00000000},
+ {0xc98, 0x00020e1a}, {0xc9c, 0x00007f7f},
+ {0xca0, 0x00000000}, {0xca4, 0x000300a0},
+ {0xca8, 0x00000000}, {0xcac, 0x00000000},
+ {0xcb0, 0x00000000}, {0xcb4, 0x00000000},
+ {0xcb8, 0x00000000}, {0xcbc, 0x28000000},
+ {0xcc0, 0x00000000}, {0xcc4, 0x00000000},
+ {0xcc8, 0x00000000}, {0xccc, 0x00000000},
+ {0xcd0, 0x00000000}, {0xcd4, 0x00000000},
+ {0xcd8, 0x64b22427}, {0xcdc, 0x00766932},
+ {0xce0, 0x00222222}, {0xce4, 0x00000000},
+ {0xce8, 0x37644302}, {0xcec, 0x2f97d40c},
+ {0xd00, 0x00000740}, {0xd04, 0x40020401},
+ {0xd08, 0x0000907f}, {0xd0c, 0x20010201},
+ {0xd10, 0xa0633333}, {0xd14, 0x3333bc53},
+ {0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975},
+ {0xd30, 0x00000000}, {0xd34, 0x80608000},
+ {0xd38, 0x00000000}, {0xd3c, 0x00127353},
+ {0xd40, 0x00000000}, {0xd44, 0x00000000},
+ {0xd48, 0x00000000}, {0xd4c, 0x00000000},
+ {0xd50, 0x6437140a}, {0xd54, 0x00000000},
+ {0xd58, 0x00000282}, {0xd5c, 0x30032064},
+ {0xd60, 0x4653de68}, {0xd64, 0x04518a3c},
+ {0xd68, 0x00002101}, {0xd6c, 0x2a201c16},
+ {0xd70, 0x1812362e}, {0xd74, 0x322c2220},
+ {0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d},
+ {0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d},
+ {0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d},
+ {0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d},
+ {0xe28, 0x00000000}, {0xe30, 0x1000dc1f},
+ {0xe34, 0x10008c1f}, {0xe38, 0x02140102},
+ {0xe3c, 0x681604c2}, {0xe40, 0x01007c00},
+ {0xe44, 0x01004800}, {0xe48, 0xfb000000},
+ {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f},
+ {0xe54, 0x10008c1f}, {0xe58, 0x02140102},
+ {0xe5c, 0x28160d05}, {0xe60, 0x00000008},
+ {0xe68, 0x001b2556}, {0xe6c, 0x00c00096},
+ {0xe70, 0x00c00096}, {0xe74, 0x01000056},
+ {0xe78, 0x01000014}, {0xe7c, 0x01000056},
+ {0xe80, 0x01000014}, {0xe84, 0x00c00096},
+ {0xe88, 0x01000056}, {0xe8c, 0x00c00096},
+ {0xed0, 0x00c00096}, {0xed4, 0x00c00096},
+ {0xed8, 0x00c00096}, {0xedc, 0x000000d6},
+ {0xee0, 0x000000d6}, {0xeec, 0x01c00016},
+ {0xf14, 0x00000003}, {0xf4c, 0x00000000},
+ {0xf00, 0x00000300},
+ {0x820, 0x01000100}, {0x800, 0x83040000},
+ {0xffff, 0xffffffff},
+};
+
+static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = {
+ {0xc78, 0xfd000001}, {0xc78, 0xfc010001},
+ {0xc78, 0xfb020001}, {0xc78, 0xfa030001},
+ {0xc78, 0xf9040001}, {0xc78, 0xf8050001},
+ {0xc78, 0xf7060001}, {0xc78, 0xf6070001},
+ {0xc78, 0xf5080001}, {0xc78, 0xf4090001},
+ {0xc78, 0xf30a0001}, {0xc78, 0xf20b0001},
+ {0xc78, 0xf10c0001}, {0xc78, 0xf00d0001},
+ {0xc78, 0xef0e0001}, {0xc78, 0xee0f0001},
+ {0xc78, 0xed100001}, {0xc78, 0xec110001},
+ {0xc78, 0xeb120001}, {0xc78, 0xea130001},
+ {0xc78, 0xe9140001}, {0xc78, 0xe8150001},
+ {0xc78, 0xe7160001}, {0xc78, 0xe6170001},
+ {0xc78, 0xe5180001}, {0xc78, 0xe4190001},
+ {0xc78, 0xe31a0001}, {0xc78, 0xa51b0001},
+ {0xc78, 0xa41c0001}, {0xc78, 0xa31d0001},
+ {0xc78, 0x671e0001}, {0xc78, 0x661f0001},
+ {0xc78, 0x65200001}, {0xc78, 0x64210001},
+ {0xc78, 0x63220001}, {0xc78, 0x4a230001},
+ {0xc78, 0x49240001}, {0xc78, 0x48250001},
+ {0xc78, 0x47260001}, {0xc78, 0x46270001},
+ {0xc78, 0x45280001}, {0xc78, 0x44290001},
+ {0xc78, 0x432a0001}, {0xc78, 0x422b0001},
+ {0xc78, 0x292c0001}, {0xc78, 0x282d0001},
+ {0xc78, 0x272e0001}, {0xc78, 0x262f0001},
+ {0xc78, 0x0a300001}, {0xc78, 0x09310001},
+ {0xc78, 0x08320001}, {0xc78, 0x07330001},
+ {0xc78, 0x06340001}, {0xc78, 0x05350001},
+ {0xc78, 0x04360001}, {0xc78, 0x03370001},
+ {0xc78, 0x02380001}, {0xc78, 0x01390001},
+ {0xc78, 0x013a0001}, {0xc78, 0x013b0001},
+ {0xc78, 0x013c0001}, {0xc78, 0x013d0001},
+ {0xc78, 0x013e0001}, {0xc78, 0x013f0001},
+ {0xc78, 0xfc400001}, {0xc78, 0xfb410001},
+ {0xc78, 0xfa420001}, {0xc78, 0xf9430001},
+ {0xc78, 0xf8440001}, {0xc78, 0xf7450001},
+ {0xc78, 0xf6460001}, {0xc78, 0xf5470001},
+ {0xc78, 0xf4480001}, {0xc78, 0xf3490001},
+ {0xc78, 0xf24a0001}, {0xc78, 0xf14b0001},
+ {0xc78, 0xf04c0001}, {0xc78, 0xef4d0001},
+ {0xc78, 0xee4e0001}, {0xc78, 0xed4f0001},
+ {0xc78, 0xec500001}, {0xc78, 0xeb510001},
+ {0xc78, 0xea520001}, {0xc78, 0xe9530001},
+ {0xc78, 0xe8540001}, {0xc78, 0xe7550001},
+ {0xc78, 0xe6560001}, {0xc78, 0xe5570001},
+ {0xc78, 0xe4580001}, {0xc78, 0xe3590001},
+ {0xc78, 0xa65a0001}, {0xc78, 0xa55b0001},
+ {0xc78, 0xa45c0001}, {0xc78, 0xa35d0001},
+ {0xc78, 0x675e0001}, {0xc78, 0x665f0001},
+ {0xc78, 0x65600001}, {0xc78, 0x64610001},
+ {0xc78, 0x63620001}, {0xc78, 0x62630001},
+ {0xc78, 0x61640001}, {0xc78, 0x48650001},
+ {0xc78, 0x47660001}, {0xc78, 0x46670001},
+ {0xc78, 0x45680001}, {0xc78, 0x44690001},
+ {0xc78, 0x436a0001}, {0xc78, 0x426b0001},
+ {0xc78, 0x286c0001}, {0xc78, 0x276d0001},
+ {0xc78, 0x266e0001}, {0xc78, 0x256f0001},
+ {0xc78, 0x24700001}, {0xc78, 0x09710001},
+ {0xc78, 0x08720001}, {0xc78, 0x07730001},
+ {0xc78, 0x06740001}, {0xc78, 0x05750001},
+ {0xc78, 0x04760001}, {0xc78, 0x03770001},
+ {0xc78, 0x02780001}, {0xc78, 0x01790001},
+ {0xc78, 0x017a0001}, {0xc78, 0x017b0001},
+ {0xc78, 0x017c0001}, {0xc78, 0x017d0001},
+ {0xc78, 0x017e0001}, {0xc78, 0x017f0001},
+ {0xc50, 0x69553422},
+ {0xc50, 0x69553420},
+ {0x824, 0x00390204},
+ {0xffff, 0xffffffff}
+};
+
+static struct rtl8xxxu_rfregval rtl8723bu_radioa_1t_init_table[] = {
+ {0x00, 0x00010000}, {0xb0, 0x000dffe0},
+ {0xfe, 0x00000000}, {0xfe, 0x00000000},
+ {0xfe, 0x00000000}, {0xb1, 0x00000018},
+ {0xfe, 0x00000000}, {0xfe, 0x00000000},
+ {0xfe, 0x00000000}, {0xb2, 0x00084c00},
+ {0xb5, 0x0000d2cc}, {0xb6, 0x000925aa},
+ {0xb7, 0x00000010}, {0xb8, 0x0000907f},
+ {0x5c, 0x00000002}, {0x7c, 0x00000002},
+ {0x7e, 0x00000005}, {0x8b, 0x0006fc00},
+ {0xb0, 0x000ff9f0}, {0x1c, 0x000739d2},
+ {0x1e, 0x00000000}, {0xdf, 0x00000780},
+ {0x50, 0x00067435},
+ /*
+ * The 8723bu vendor driver indicates that bit 8 should be set in
+ * 0x51 for package types TFBGA90, TFBGA80, and TFBGA79. However
+ * they never actually check the package type - and just default
+ * to not setting it.
+ */
+ {0x51, 0x0006b04e},
+ {0x52, 0x000007d2}, {0x53, 0x00000000},
+ {0x54, 0x00050400}, {0x55, 0x0004026e},
+ {0xdd, 0x0000004c}, {0x70, 0x00067435},
+ /*
+ * 0x71 has same package type condition as for register 0x51
+ */
+ {0x71, 0x0006b04e},
+ {0x72, 0x000007d2}, {0x73, 0x00000000},
+ {0x74, 0x00050400}, {0x75, 0x0004026e},
+ {0xef, 0x00000100}, {0x34, 0x0000add7},
+ {0x35, 0x00005c00}, {0x34, 0x00009dd4},
+ {0x35, 0x00005000}, {0x34, 0x00008dd1},
+ {0x35, 0x00004400}, {0x34, 0x00007dce},
+ {0x35, 0x00003800}, {0x34, 0x00006cd1},
+ {0x35, 0x00004400}, {0x34, 0x00005cce},
+ {0x35, 0x00003800}, {0x34, 0x000048ce},
+ {0x35, 0x00004400}, {0x34, 0x000034ce},
+ {0x35, 0x00003800}, {0x34, 0x00002451},
+ {0x35, 0x00004400}, {0x34, 0x0000144e},
+ {0x35, 0x00003800}, {0x34, 0x00000051},
+ {0x35, 0x00004400}, {0xef, 0x00000000},
+ {0xef, 0x00000100}, {0xed, 0x00000010},
+ {0x44, 0x0000add7}, {0x44, 0x00009dd4},
+ {0x44, 0x00008dd1}, {0x44, 0x00007dce},
+ {0x44, 0x00006cc1}, {0x44, 0x00005cce},
+ {0x44, 0x000044d1}, {0x44, 0x000034ce},
+ {0x44, 0x00002451}, {0x44, 0x0000144e},
+ {0x44, 0x00000051}, {0xef, 0x00000000},
+ {0xed, 0x00000000}, {0x7f, 0x00020080},
+ {0xef, 0x00002000}, {0x3b, 0x000380ef},
+ {0x3b, 0x000302fe}, {0x3b, 0x00028ce6},
+ {0x3b, 0x000200bc}, {0x3b, 0x000188a5},
+ {0x3b, 0x00010fbc}, {0x3b, 0x00008f71},
+ {0x3b, 0x00000900}, {0xef, 0x00000000},
+ {0xed, 0x00000001}, {0x40, 0x000380ef},
+ {0x40, 0x000302fe}, {0x40, 0x00028ce6},
+ {0x40, 0x000200bc}, {0x40, 0x000188a5},
+ {0x40, 0x00010fbc}, {0x40, 0x00008f71},
+ {0x40, 0x00000900}, {0xed, 0x00000000},
+ {0x82, 0x00080000}, {0x83, 0x00008000},
+ {0x84, 0x00048d80}, {0x85, 0x00068000},
+ {0xa2, 0x00080000}, {0xa3, 0x00008000},
+ {0xa4, 0x00048d80}, {0xa5, 0x00068000},
+ {0xed, 0x00000002}, {0xef, 0x00000002},
+ {0x56, 0x00000032}, {0x76, 0x00000032},
+ {0x01, 0x00000780},
+ {0xff, 0xffffffff}
+};
+
+static void rtl8723bu_write_btreg(struct rtl8xxxu_priv *priv, u8 reg, u8 data)
+{
+ struct h2c_cmd h2c;
+ int reqnum = 0;
+
+ memset(&h2c, 0, sizeof(struct h2c_cmd));
+ h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER;
+ h2c.bt_mp_oper.operreq = 0 | (reqnum << 4);
+ h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE;
+ h2c.bt_mp_oper.data = data;
+ rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper));
+
+ reqnum++;
+ memset(&h2c, 0, sizeof(struct h2c_cmd));
+ h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER;
+ h2c.bt_mp_oper.operreq = 0 | (reqnum << 4);
+ h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE;
+ h2c.bt_mp_oper.addr = reg;
+ rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper));
+}
+
+static void rtl8723bu_reset_8051(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u16 sys_func;
+
+ val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL);
+ val8 &= ~BIT(1);
+ rtl8xxxu_write8(priv, REG_RSV_CTRL, val8);
+
+ val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
+ val8 &= ~BIT(0);
+ rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
+
+ sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+ sys_func &= ~SYS_FUNC_CPU_ENABLE;
+ rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
+
+ val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL);
+ val8 &= ~BIT(1);
+ rtl8xxxu_write8(priv, REG_RSV_CTRL, val8);
+
+ val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
+ val8 |= BIT(0);
+ rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
+
+ sys_func |= SYS_FUNC_CPU_ENABLE;
+ rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
+}
+
+static void
+rtl8723b_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40)
+{
+ u32 val32, ofdm, mcs;
+ u8 cck, ofdmbase, mcsbase;
+ int group, tx_idx;
+
+ tx_idx = 0;
+ group = rtl8xxxu_gen2_channel_to_group(channel);
+
+ cck = priv->cck_tx_power_index_B[group];
+ val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32);
+ val32 &= 0xffff00ff;
+ val32 |= (cck << 8);
+ rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11);
+ val32 &= 0xff;
+ val32 |= ((cck << 8) | (cck << 16) | (cck << 24));
+ rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32);
+
+ ofdmbase = priv->ht40_1s_tx_power_index_B[group];
+ ofdmbase += priv->ofdm_tx_power_diff[tx_idx].b;
+ ofdm = ofdmbase | ofdmbase << 8 | ofdmbase << 16 | ofdmbase << 24;
+
+ rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm);
+ rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm);
+
+ mcsbase = priv->ht40_1s_tx_power_index_B[group];
+ if (ht40)
+ mcsbase += priv->ht40_tx_power_diff[tx_idx++].b;
+ else
+ mcsbase += priv->ht20_tx_power_diff[tx_idx++].b;
+ mcs = mcsbase | mcsbase << 8 | mcsbase << 16 | mcsbase << 24;
+
+ rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs);
+ rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs);
+}
+
+static int rtl8723bu_parse_efuse(struct rtl8xxxu_priv *priv)
+{
+ struct rtl8723bu_efuse *efuse = &priv->efuse_wifi.efuse8723bu;
+ int i;
+
+ if (efuse->rtl_id != cpu_to_le16(0x8129))
+ return -EINVAL;
+
+ ether_addr_copy(priv->mac_addr, efuse->mac_addr);
+
+ memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base,
+ sizeof(efuse->tx_power_index_A.cck_base));
+ memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base,
+ sizeof(efuse->tx_power_index_B.cck_base));
+
+ memcpy(priv->ht40_1s_tx_power_index_A,
+ efuse->tx_power_index_A.ht40_base,
+ sizeof(efuse->tx_power_index_A.ht40_base));
+ memcpy(priv->ht40_1s_tx_power_index_B,
+ efuse->tx_power_index_B.ht40_base,
+ sizeof(efuse->tx_power_index_B.ht40_base));
+
+ priv->ofdm_tx_power_diff[0].a =
+ efuse->tx_power_index_A.ht20_ofdm_1s_diff.a;
+ priv->ofdm_tx_power_diff[0].b =
+ efuse->tx_power_index_B.ht20_ofdm_1s_diff.a;
+
+ priv->ht20_tx_power_diff[0].a =
+ efuse->tx_power_index_A.ht20_ofdm_1s_diff.b;
+ priv->ht20_tx_power_diff[0].b =
+ efuse->tx_power_index_B.ht20_ofdm_1s_diff.b;
+
+ priv->ht40_tx_power_diff[0].a = 0;
+ priv->ht40_tx_power_diff[0].b = 0;
+
+ for (i = 1; i < RTL8723B_TX_COUNT; i++) {
+ priv->ofdm_tx_power_diff[i].a =
+ efuse->tx_power_index_A.pwr_diff[i - 1].ofdm;
+ priv->ofdm_tx_power_diff[i].b =
+ efuse->tx_power_index_B.pwr_diff[i - 1].ofdm;
+
+ priv->ht20_tx_power_diff[i].a =
+ efuse->tx_power_index_A.pwr_diff[i - 1].ht20;
+ priv->ht20_tx_power_diff[i].b =
+ efuse->tx_power_index_B.pwr_diff[i - 1].ht20;
+
+ priv->ht40_tx_power_diff[i].a =
+ efuse->tx_power_index_A.pwr_diff[i - 1].ht40;
+ priv->ht40_tx_power_diff[i].b =
+ efuse->tx_power_index_B.pwr_diff[i - 1].ht40;
+ }
+
+ priv->has_xtalk = 1;
+ priv->xtalk = priv->efuse_wifi.efuse8723bu.xtal_k & 0x3f;
+
+ dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name);
+ dev_info(&priv->udev->dev, "Product: %.41s\n", efuse->device_name);
+
+ if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) {
+ int i;
+ unsigned char *raw = priv->efuse_wifi.raw;
+
+ dev_info(&priv->udev->dev,
+ "%s: dumping efuse (0x%02zx bytes):\n",
+ __func__, sizeof(struct rtl8723bu_efuse));
+ for (i = 0; i < sizeof(struct rtl8723bu_efuse); i += 8) {
+ dev_info(&priv->udev->dev, "%02x: "
+ "%02x %02x %02x %02x %02x %02x %02x %02x\n", i,
+ raw[i], raw[i + 1], raw[i + 2],
+ raw[i + 3], raw[i + 4], raw[i + 5],
+ raw[i + 6], raw[i + 7]);
+ }
+ }
+
+ return 0;
+}
+
+static int rtl8723bu_load_firmware(struct rtl8xxxu_priv *priv)
+{
+ char *fw_name;
+ int ret;
+
+ if (priv->enable_bluetooth)
+ fw_name = "rtlwifi/rtl8723bu_bt.bin";
+ else
+ fw_name = "rtlwifi/rtl8723bu_nic.bin";
+
+ ret = rtl8xxxu_load_firmware(priv, fw_name);
+ return ret;
+}
+
+static void rtl8723bu_init_phy_bb(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u16 val16;
+
+ val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+ val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | SYS_FUNC_DIO_RF;
+ rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
+
+ /* 6. 0x1f[7:0] = 0x07 */
+ val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
+ rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
+
+ /* Why? */
+ rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3);
+ rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80);
+ rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table);
+
+ rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table);
+}
+
+static int rtl8723bu_init_phy_rf(struct rtl8xxxu_priv *priv)
+{
+ int ret;
+
+ ret = rtl8xxxu_init_phy_rf(priv, rtl8723bu_radioa_1t_init_table, RF_A);
+ /*
+ * PHY LCK
+ */
+ rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdfbe0);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, 0x8c01);
+ msleep(200);
+ rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdffe0);
+
+ return ret;
+}
+
+static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv)
+{
+ u32 val32;
+
+ val32 = rtl8xxxu_read32(priv, REG_PAD_CTRL1);
+ val32 &= ~(BIT(20) | BIT(24));
+ rtl8xxxu_write32(priv, REG_PAD_CTRL1, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
+ val32 &= ~BIT(4);
+ rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
+ val32 |= BIT(3);
+ rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
+ val32 |= BIT(24);
+ rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
+ val32 &= ~BIT(23);
+ rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER);
+ val32 |= (BIT(0) | BIT(1));
+ rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_RFE_CTRL_ANTA_SRC);
+ val32 &= 0xffffff00;
+ val32 |= 0x77;
+ rtl8xxxu_write32(priv, REG_RFE_CTRL_ANTA_SRC, val32);
+
+ val32 = rtl8xxxu_read32(priv, REG_PWR_DATA);
+ val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
+ rtl8xxxu_write32(priv, REG_PWR_DATA, val32);
+}
+
+static int rtl8723bu_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+ u32 reg_eac, reg_e94, reg_e9c, path_sel, val32;
+ int result = 0;
+
+ path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
+
+ /*
+ * Leave IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /*
+ * Enable path A PA in TX IQK mode
+ */
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
+ val32 |= 0x80000;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x20000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0003f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xc7f87);
+
+ /*
+ * Tx IQK setting
+ */
+ rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* path-A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x821403ea);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000);
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911);
+
+ /*
+ * Enter IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ val32 |= 0x80800000;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /*
+ * The vendor driver indicates the USB module is always using
+ * S0S1 path 1 for the 8723bu. This may be different for 8192eu
+ */
+ if (priv->rf_paths > 1)
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
+ else
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
+
+ /*
+ * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu.
+ * No trace of this in the 8192eu or 8188eu vendor drivers.
+ */
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(1);
+
+ /* Restore Ant Path */
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
+#ifdef RTL8723BU_BT
+ /* GNT_BT = 1 */
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
+#endif
+
+ /*
+ * Leave IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+ reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+ val32 = (reg_e9c >> 16) & 0x3ff;
+ if (val32 & 0x200)
+ val32 = 0x400 - val32;
+
+ if (!(reg_eac & BIT(28)) &&
+ ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+ ((reg_e9c & 0x03ff0000) != 0x00420000) &&
+ ((reg_e94 & 0x03ff0000) < 0x01100000) &&
+ ((reg_e94 & 0x03ff0000) > 0x00f00000) &&
+ val32 < 0xf)
+ result |= 0x01;
+ else /* If TX not OK, ignore RX */
+ goto out;
+
+out:
+ return result;
+}
+
+static int rtl8723bu_rx_iqk_path_a(struct rtl8xxxu_priv *priv)
+{
+ u32 reg_ea4, reg_eac, reg_e94, reg_e9c, path_sel, val32;
+ int result = 0;
+
+ path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
+
+ /*
+ * Leave IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /*
+ * Enable path A PA in TX IQK mode
+ */
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
+ val32 |= 0x80000;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7);
+
+ /*
+ * Tx IQK setting
+ */
+ rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* path-A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160ff0);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000);
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
+
+ /*
+ * Enter IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ val32 |= 0x80800000;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /*
+ * The vendor driver indicates the USB module is always using
+ * S0S1 path 1 for the 8723bu. This may be different for 8192eu
+ */
+ if (priv->rf_paths > 1)
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
+ else
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
+
+ /*
+ * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu.
+ * No trace of this in the 8192eu or 8188eu vendor drivers.
+ */
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(1);
+
+ /* Restore Ant Path */
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
+#ifdef RTL8723BU_BT
+ /* GNT_BT = 1 */
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
+#endif
+
+ /*
+ * Leave IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
+ reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
+
+ val32 = (reg_e9c >> 16) & 0x3ff;
+ if (val32 & 0x200)
+ val32 = 0x400 - val32;
+
+ if (!(reg_eac & BIT(28)) &&
+ ((reg_e94 & 0x03ff0000) != 0x01420000) &&
+ ((reg_e9c & 0x03ff0000) != 0x00420000) &&
+ ((reg_e94 & 0x03ff0000) < 0x01100000) &&
+ ((reg_e94 & 0x03ff0000) > 0x00f00000) &&
+ val32 < 0xf)
+ result |= 0x01;
+ else /* If TX not OK, ignore RX */
+ goto out;
+
+ val32 = 0x80007c00 | (reg_e94 &0x3ff0000) |
+ ((reg_e9c & 0x3ff0000) >> 16);
+ rtl8xxxu_write32(priv, REG_TX_IQK, val32);
+
+ /*
+ * Modify RX IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
+ val32 |= 0x80000;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7d77);
+
+ /*
+ * PA, PAD setting
+ */
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0xf80);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_55, 0x4021f);
+
+ /*
+ * RX IQK setting
+ */
+ rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
+
+ /* path-A IQK setting */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c);
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
+
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82110000);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x2816001f);
+ rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
+ rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
+
+ /* LO calibration setting */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a8d1);
+
+ /*
+ * Enter IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ val32 |= 0x80800000;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ if (priv->rf_paths > 1)
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
+ else
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
+
+ /*
+ * Disable BT
+ */
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
+
+ /* One shot, path A LOK & IQK */
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
+ rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
+
+ mdelay(1);
+
+ /* Restore Ant Path */
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
+#ifdef RTL8723BU_BT
+ /* GNT_BT = 1 */
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
+#endif
+
+ /*
+ * Leave IQK mode
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /* Check failed */
+ reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
+ reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2);
+
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x780);
+
+ val32 = (reg_eac >> 16) & 0x3ff;
+ if (val32 & 0x200)
+ val32 = 0x400 - val32;
+
+ if (!(reg_eac & BIT(27)) &&
+ ((reg_ea4 & 0x03ff0000) != 0x01320000) &&
+ ((reg_eac & 0x03ff0000) != 0x00360000) &&
+ ((reg_ea4 & 0x03ff0000) < 0x01100000) &&
+ ((reg_ea4 & 0x03ff0000) > 0x00f00000) &&
+ val32 < 0xf)
+ result |= 0x02;
+ else /* If TX not OK, ignore RX */
+ goto out;
+out:
+ return result;
+}
+
+static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
+ int result[][8], int t)
+{
+ struct device *dev = &priv->udev->dev;
+ u32 i, val32;
+ int path_a_ok /*, path_b_ok */;
+ int retry = 2;
+ const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
+ REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
+ REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
+ REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
+ REG_TX_OFDM_BBON, REG_TX_TO_RX,
+ REG_TX_TO_TX, REG_RX_CCK,
+ REG_RX_OFDM, REG_RX_WAIT_RIFS,
+ REG_RX_TO_RX, REG_STANDBY,
+ REG_SLEEP, REG_PMPD_ANAEN
+ };
+ const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
+ REG_TXPAUSE, REG_BEACON_CTRL,
+ REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
+ };
+ const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
+ REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
+ REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
+ REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
+ REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE
+ };
+ u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff;
+ u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff;
+
+ /*
+ * Note: IQ calibration must be performed after loading
+ * PHY_REG.txt , and radio_a, radio_b.txt
+ */
+
+ if (t == 0) {
+ /* Save ADDA parameters, turn Path A ADDA on */
+ rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup,
+ RTL8XXXU_ADDA_REGS);
+ rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+ rtl8xxxu_save_regs(priv, iqk_bb_regs,
+ priv->bb_backup, RTL8XXXU_BB_REGS);
+ }
+
+ rtl8xxxu_path_adda_on(priv, adda_regs, true);
+
+ /* MAC settings */
+ rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup);
+
+ val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING);
+ val32 |= 0x0f000000;
+ rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32);
+
+ rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600);
+ rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
+ rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000);
+
+ /*
+ * RX IQ calibration setting for 8723B D cut large current issue
+ * when leaving IPS
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
+ val32 |= 0x80000;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
+
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7);
+
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED);
+ val32 |= 0x20;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
+
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_43, 0x60fbd);
+
+ for (i = 0; i < retry; i++) {
+ path_a_ok = rtl8723bu_iqk_path_a(priv);
+ if (path_a_ok == 0x01) {
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ val32 = rtl8xxxu_read32(priv,
+ REG_TX_POWER_BEFORE_IQK_A);
+ result[t][0] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv,
+ REG_TX_POWER_AFTER_IQK_A);
+ result[t][1] = (val32 >> 16) & 0x3ff;
+
+ break;
+ }
+ }
+
+ if (!path_a_ok)
+ dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__);
+
+ for (i = 0; i < retry; i++) {
+ path_a_ok = rtl8723bu_rx_iqk_path_a(priv);
+ if (path_a_ok == 0x03) {
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_BEFORE_IQK_A_2);
+ result[t][2] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_AFTER_IQK_A_2);
+ result[t][3] = (val32 >> 16) & 0x3ff;
+
+ break;
+ }
+ }
+
+ if (!path_a_ok)
+ dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__);
+
+ if (priv->tx_paths > 1) {
+#if 1
+ dev_warn(dev, "%s: Path B not supported\n", __func__);
+#else
+
+ /*
+ * Path A into standby
+ */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000);
+
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ val32 |= 0x80800000;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ /* Turn Path B ADDA on */
+ rtl8xxxu_path_adda_on(priv, adda_regs, false);
+
+ for (i = 0; i < retry; i++) {
+ path_b_ok = rtl8xxxu_iqk_path_b(priv);
+ if (path_b_ok == 0x03) {
+ val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
+ result[t][4] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
+ result[t][5] = (val32 >> 16) & 0x3ff;
+ break;
+ }
+ }
+
+ if (!path_b_ok)
+ dev_dbg(dev, "%s: Path B IQK failed!\n", __func__);
+
+ for (i = 0; i < retry; i++) {
+ path_b_ok = rtl8723bu_rx_iqk_path_b(priv);
+ if (path_a_ok == 0x03) {
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_BEFORE_IQK_B_2);
+ result[t][6] = (val32 >> 16) & 0x3ff;
+ val32 = rtl8xxxu_read32(priv,
+ REG_RX_POWER_AFTER_IQK_B_2);
+ result[t][7] = (val32 >> 16) & 0x3ff;
+ break;
+ }
+ }
+
+ if (!path_b_ok)
+ dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__);
+#endif
+ }
+
+ /* Back to BB mode, load original value */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 &= 0x000000ff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+
+ if (t) {
+ /* Reload ADDA power saving parameters */
+ rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup,
+ RTL8XXXU_ADDA_REGS);
+
+ /* Reload MAC parameters */
+ rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
+
+ /* Reload BB parameters */
+ rtl8xxxu_restore_regs(priv, iqk_bb_regs,
+ priv->bb_backup, RTL8XXXU_BB_REGS);
+
+ /* Restore RX initial gain */
+ val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1);
+ val32 &= 0xffffff00;
+ rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50);
+ rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc);
+
+ if (priv->tx_paths > 1) {
+ val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1);
+ val32 &= 0xffffff00;
+ rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
+ val32 | 0x50);
+ rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
+ val32 | xb_agc);
+ }
+
+ /* Load 0xe30 IQC default value */
+ rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00);
+ rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00);
+ }
+}
+
+static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
+{
+ struct device *dev = &priv->udev->dev;
+ int result[4][8]; /* last is final result */
+ int i, candidate;
+ bool path_a_ok, path_b_ok;
+ u32 reg_e94, reg_e9c, reg_ea4, reg_eac;
+ u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc;
+ u32 val32, bt_control;
+ s32 reg_tmp = 0;
+ bool simu;
+
+ rtl8xxxu_prepare_calibrate(priv, 1);
+
+ memset(result, 0, sizeof(result));
+ candidate = -1;
+
+ path_a_ok = false;
+ path_b_ok = false;
+
+ bt_control = rtl8xxxu_read32(priv, REG_BT_CONTROL_8723BU);
+
+ for (i = 0; i < 3; i++) {
+ rtl8723bu_phy_iqcalibrate(priv, result, i);
+
+ if (i == 1) {
+ simu = rtl8xxxu_gen2_simularity_compare(priv,
+ result, 0, 1);
+ if (simu) {
+ candidate = 0;
+ break;
+ }
+ }
+
+ if (i == 2) {
+ simu = rtl8xxxu_gen2_simularity_compare(priv,
+ result, 0, 2);
+ if (simu) {
+ candidate = 0;
+ break;
+ }
+
+ simu = rtl8xxxu_gen2_simularity_compare(priv,
+ result, 1, 2);
+ if (simu) {
+ candidate = 1;
+ } else {
+ for (i = 0; i < 8; i++)
+ reg_tmp += result[3][i];
+
+ if (reg_tmp)
+ candidate = 3;
+ else
+ candidate = -1;
+ }
+ }
+ }
+
+ for (i = 0; i < 4; i++) {
+ reg_e94 = result[i][0];
+ reg_e9c = result[i][1];
+ reg_ea4 = result[i][2];
+ reg_eac = result[i][3];
+ reg_eb4 = result[i][4];
+ reg_ebc = result[i][5];
+ reg_ec4 = result[i][6];
+ reg_ecc = result[i][7];
+ }
+
+ if (candidate >= 0) {
+ reg_e94 = result[candidate][0];
+ priv->rege94 = reg_e94;
+ reg_e9c = result[candidate][1];
+ priv->rege9c = reg_e9c;
+ reg_ea4 = result[candidate][2];
+ reg_eac = result[candidate][3];
+ reg_eb4 = result[candidate][4];
+ priv->regeb4 = reg_eb4;
+ reg_ebc = result[candidate][5];
+ priv->regebc = reg_ebc;
+ reg_ec4 = result[candidate][6];
+ reg_ecc = result[candidate][7];
+ dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate);
+ dev_dbg(dev,
+ "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x "
+ "ecc=%x\n ", __func__, reg_e94, reg_e9c,
+ reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc);
+ path_a_ok = true;
+ path_b_ok = true;
+ } else {
+ reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100;
+ reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0;
+ }
+
+ if (reg_e94 && candidate >= 0)
+ rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result,
+ candidate, (reg_ea4 == 0));
+
+ if (priv->tx_paths > 1 && reg_eb4)
+ rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result,
+ candidate, (reg_ec4 == 0));
+
+ rtl8xxxu_save_regs(priv, rtl8xxxu_iqk_phy_iq_bb_reg,
+ priv->bb_recovery_backup, RTL8XXXU_BB_REGS);
+
+ rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, bt_control);
+
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
+ val32 |= 0x80000;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x18000);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xe6177);
+ val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED);
+ val32 |= 0x20;
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
+ rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd);
+
+ if (priv->rf_paths > 1)
+ dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__);
+
+ rtl8xxxu_prepare_calibrate(priv, 0);
+}
+
+static int rtl8723bu_active_to_emu(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u16 val16;
+ u32 val32;
+ int count, ret = 0;
+
+ /* Turn off RF */
+ rtl8xxxu_write8(priv, REG_RF_CTRL, 0);
+
+ /* Enable rising edge triggering interrupt */
+ val16 = rtl8xxxu_read16(priv, REG_GPIO_INTM);
+ val16 &= ~GPIO_INTM_EDGE_TRIG_IRQ;
+ rtl8xxxu_write16(priv, REG_GPIO_INTM, val16);
+
+ /* Release WLON reset 0x04[16]= 1*/
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ val32 |= APS_FSMCO_WLON_RESET;
+ rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+ /* 0x0005[1] = 1 turn off MAC by HW state machine*/
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ val8 |= BIT(1);
+ rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
+
+ for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ if ((val8 & BIT(1)) == 0)
+ break;
+ udelay(10);
+ }
+
+ if (!count) {
+ dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n",
+ __func__);
+ ret = -EBUSY;
+ goto exit;
+ }
+
+ /* Enable BT control XTAL setting */
+ val8 = rtl8xxxu_read8(priv, REG_AFE_MISC);
+ val8 &= ~AFE_MISC_WL_XTAL_CTRL;
+ rtl8xxxu_write8(priv, REG_AFE_MISC, val8);
+
+ /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */
+ val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
+ val8 |= SYS_ISO_ANALOG_IPS;
+ rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
+
+ /* 0x0020[0] = 0 disable LDOA12 MACRO block*/
+ val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
+ val8 &= ~LDOA15_ENABLE;
+ rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
+
+exit:
+ return ret;
+}
+
+static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u32 val32;
+ int count, ret = 0;
+
+ /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */
+ val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
+ val8 |= LDOA15_ENABLE;
+ rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
+
+ /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/
+ val8 = rtl8xxxu_read8(priv, 0x0067);
+ val8 &= ~BIT(4);
+ rtl8xxxu_write8(priv, 0x0067, val8);
+
+ mdelay(1);
+
+ /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */
+ val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
+ val8 &= ~SYS_ISO_ANALOG_IPS;
+ rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
+
+ /* Disable SW LPS 0x04[10]= 0 */
+ val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO);
+ val32 &= ~APS_FSMCO_SW_LPS;
+ rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+ /* Wait until 0x04[17] = 1 power ready */
+ for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ if (val32 & BIT(17))
+ break;
+
+ udelay(10);
+ }
+
+ if (!count) {
+ ret = -EBUSY;
+ goto exit;
+ }
+
+ /* We should be able to optimize the following three entries into one */
+
+ /* Release WLON reset 0x04[16]= 1*/
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ val32 |= APS_FSMCO_WLON_RESET;
+ rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+ /* Disable HWPDN 0x04[15]= 0*/
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ val32 &= ~APS_FSMCO_HW_POWERDOWN;
+ rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+ /* Disable WL suspend*/
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE);
+ rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+ /* Set, then poll until 0 */
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ val32 |= APS_FSMCO_MAC_ENABLE;
+ rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+
+ for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
+ val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
+ if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) {
+ ret = 0;
+ break;
+ }
+ udelay(10);
+ }
+
+ if (!count) {
+ ret = -EBUSY;
+ goto exit;
+ }
+
+ /* Enable WL control XTAL setting */
+ val8 = rtl8xxxu_read8(priv, REG_AFE_MISC);
+ val8 |= AFE_MISC_WL_XTAL_CTRL;
+ rtl8xxxu_write8(priv, REG_AFE_MISC, val8);
+
+ /* Enable falling edge triggering interrupt */
+ val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1);
+ val8 |= BIT(1);
+ rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8);
+
+ /* Enable GPIO9 interrupt mode */
+ val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1);
+ val8 |= BIT(1);
+ rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8);
+
+ /* Enable GPIO9 input mode */
+ val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2);
+ val8 &= ~BIT(1);
+ rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8);
+
+ /* Enable HSISR GPIO[C:0] interrupt */
+ val8 = rtl8xxxu_read8(priv, REG_HSIMR);
+ val8 |= BIT(0);
+ rtl8xxxu_write8(priv, REG_HSIMR, val8);
+
+ /* Enable HSISR GPIO9 interrupt */
+ val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2);
+ val8 |= BIT(1);
+ rtl8xxxu_write8(priv, REG_HSIMR + 2, val8);
+
+ val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL);
+ val8 |= MULTI_WIFI_HW_ROF_EN;
+ rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8);
+
+ /* For GPIO9 internal pull high setting BIT(14) */
+ val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1);
+ val8 |= BIT(6);
+ rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8);
+
+exit:
+ return ret;
+}
+
+static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u16 val16;
+ u32 val32;
+ int ret;
+
+ rtl8723a_disabled_to_emu(priv);
+
+ ret = rtl8723b_emu_to_active(priv);
+ if (ret)
+ goto exit;
+
+ /*
+ * Enable MAC DMA/WMAC/SCHEDULE/SEC block
+ * Set CR bit10 to enable 32k calibration.
+ */
+ val16 = rtl8xxxu_read16(priv, REG_CR);
+ val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE |
+ CR_TXDMA_ENABLE | CR_RXDMA_ENABLE |
+ CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE |
+ CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE |
+ CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE);
+ rtl8xxxu_write16(priv, REG_CR, val16);
+
+ /*
+ * BT coexist power on settings. This is identical for 1 and 2
+ * antenna parts.
+ */
+ rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20);
+
+ val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+ val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN;
+ rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+
+ rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18);
+ rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04);
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
+ /* Antenna inverse */
+ rtl8xxxu_write8(priv, 0xfe08, 0x01);
+
+ val16 = rtl8xxxu_read16(priv, REG_PWR_DATA);
+ val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
+ rtl8xxxu_write16(priv, REG_PWR_DATA, val16);
+
+ val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
+ val32 |= LEDCFG0_DPDT_SELECT;
+ rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
+
+ val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
+ val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA;
+ rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
+exit:
+ return ret;
+}
+
+static void rtl8723bu_power_off(struct rtl8xxxu_priv *priv)
+{
+ u8 val8;
+ u16 val16;
+
+ rtl8xxxu_flush_fifo(priv);
+
+ /*
+ * Disable TX report timer
+ */
+ val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL);
+ val8 &= ~TX_REPORT_CTRL_TIMER_ENABLE;
+ rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8);
+
+ rtl8xxxu_write8(priv, REG_CR, 0x0000);
+
+ rtl8xxxu_active_to_lps(priv);
+
+ /* Reset Firmware if running in RAM */
+ if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL)
+ rtl8xxxu_firmware_self_reset(priv);
+
+ /* Reset MCU */
+ val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
+ val16 &= ~SYS_FUNC_CPU_ENABLE;
+ rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
+
+ /* Reset MCU ready status */
+ rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
+
+ rtl8723bu_active_to_emu(priv);
+
+ val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
+ val8 |= BIT(3); /* APS_FSMCO_HW_SUSPEND */
+ rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
+
+ /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */
+ val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2);
+ val8 |= BIT(0);
+ rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8);
+}
+
+static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv)
+{
+ struct h2c_cmd h2c;
+ u32 val32;
+ u8 val8;
+
+ /*
+ * No indication anywhere as to what 0x0790 does. The 2 antenna
+ * vendor code preserves bits 6-7 here.
+ */
+ rtl8xxxu_write8(priv, 0x0790, 0x05);
+ /*
+ * 0x0778 seems to be related to enabling the number of antennas
+ * In the vendor driver halbtc8723b2ant_InitHwConfig() sets it
+ * to 0x03, while halbtc8723b1ant_InitHwConfig() sets it to 0x01
+ */
+ rtl8xxxu_write8(priv, 0x0778, 0x01);
+
+ val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG);
+ val8 |= BIT(5);
+ rtl8xxxu_write8(priv, REG_GPIO_MUXCFG, val8);
+
+ rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_IQADJ_G1, 0x780);
+
+ rtl8723bu_write_btreg(priv, 0x3c, 0x15); /* BT TRx Mask on */
+
+ /*
+ * Set BT grant to low
+ */
+ memset(&h2c, 0, sizeof(struct h2c_cmd));
+ h2c.bt_grant.cmd = H2C_8723B_BT_GRANT;
+ h2c.bt_grant.data = 0;
+ rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_grant));
+
+ /*
+ * WLAN action by PTA
+ */
+ rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04);
+
+ /*
+ * BT select S0/S1 controlled by WiFi
+ */
+ val8 = rtl8xxxu_read8(priv, 0x0067);
+ val8 |= BIT(5);
+ rtl8xxxu_write8(priv, 0x0067, val8);
+
+ val32 = rtl8xxxu_read32(priv, REG_PWR_DATA);
+ val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
+ rtl8xxxu_write32(priv, REG_PWR_DATA, val32);
+
+ /*
+ * Bits 6/7 are marked in/out ... but for what?
+ */
+ rtl8xxxu_write8(priv, 0x0974, 0xff);
+
+ val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER);
+ val32 |= (BIT(0) | BIT(1));
+ rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32);
+
+ rtl8xxxu_write8(priv, REG_RFE_CTRL_ANTA_SRC, 0x77);
+
+ val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
+ val32 &= ~BIT(24);
+ val32 |= BIT(23);
+ rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
+
+ /*
+ * Fix external switch Main->S1, Aux->S0
+ */
+ val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
+ val8 &= ~BIT(0);
+ rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
+
+ memset(&h2c, 0, sizeof(struct h2c_cmd));
+ h2c.ant_sel_rsv.cmd = H2C_8723B_ANT_SEL_RSV;
+ h2c.ant_sel_rsv.ant_inverse = 1;
+ h2c.ant_sel_rsv.int_switch_type = 0;
+ rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv));
+
+ /*
+ * 0x280, 0x00, 0x200, 0x80 - not clear
+ */
+ rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
+
+ /*
+ * Software control, antenna at WiFi side
+ */
+#ifdef NEED_PS_TDMA
+ rtl8723bu_set_ps_tdma(priv, 0x08, 0x00, 0x00, 0x00, 0x00);
+#endif
+
+ rtl8xxxu_write32(priv, REG_BT_COEX_TABLE1, 0x55555555);
+ rtl8xxxu_write32(priv, REG_BT_COEX_TABLE2, 0x55555555);
+ rtl8xxxu_write32(priv, REG_BT_COEX_TABLE3, 0x00ffffff);
+ rtl8xxxu_write8(priv, REG_BT_COEX_TABLE4, 0x03);
+
+ memset(&h2c, 0, sizeof(struct h2c_cmd));
+ h2c.bt_info.cmd = H2C_8723B_BT_INFO;
+ h2c.bt_info.data = BIT(0);
+ rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_info));
+
+ memset(&h2c, 0, sizeof(struct h2c_cmd));
+ h2c.ignore_wlan.cmd = H2C_8723B_BT_IGNORE_WLANACT;
+ h2c.ignore_wlan.data = 0;
+ rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ignore_wlan));
+}
+
+static void rtl8723bu_init_aggregation(struct rtl8xxxu_priv *priv)
+{
+ u32 agg_rx;
+ u8 agg_ctrl;
+
+ /*
+ * For now simply disable RX aggregation
+ */
+ agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL);
+ agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN;
+
+ agg_rx = rtl8xxxu_read32(priv, REG_RXDMA_AGG_PG_TH);
+ agg_rx &= ~RXDMA_USB_AGG_ENABLE;
+ agg_rx &= ~0xff0f;
+
+ rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl);
+ rtl8xxxu_write32(priv, REG_RXDMA_AGG_PG_TH, agg_rx);
+}
+
+static void rtl8723bu_init_statistics(struct rtl8xxxu_priv *priv)
+{
+ u32 val32;
+
+ /* Time duration for NHM unit: 4us, 0x2710=40ms */
+ rtl8xxxu_write16(priv, REG_NHM_TIMER_8723B + 2, 0x2710);
+ rtl8xxxu_write16(priv, REG_NHM_TH9_TH10_8723B + 2, 0xffff);
+ rtl8xxxu_write32(priv, REG_NHM_TH3_TO_TH0_8723B, 0xffffff52);
+ rtl8xxxu_write32(priv, REG_NHM_TH7_TO_TH4_8723B, 0xffffffff);
+ /* TH8 */
+ val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
+ val32 |= 0xff;
+ rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
+ /* Enable CCK */
+ val32 = rtl8xxxu_read32(priv, REG_NHM_TH9_TH10_8723B);
+ val32 |= BIT(8) | BIT(9) | BIT(10);
+ rtl8xxxu_write32(priv, REG_NHM_TH9_TH10_8723B, val32);
+ /* Max power amongst all RX antennas */
+ val32 = rtl8xxxu_read32(priv, REG_OFDM0_FA_RSTC);
+ val32 |= BIT(7);
+ rtl8xxxu_write32(priv, REG_OFDM0_FA_RSTC, val32);
+}
+
+struct rtl8xxxu_fileops rtl8723bu_fops = {
+ .parse_efuse = rtl8723bu_parse_efuse,
+ .load_firmware = rtl8723bu_load_firmware,
+ .power_on = rtl8723bu_power_on,
+ .power_off = rtl8723bu_power_off,
+ .reset_8051 = rtl8723bu_reset_8051,
+ .llt_init = rtl8xxxu_auto_llt_table,
+ .init_phy_bb = rtl8723bu_init_phy_bb,
+ .init_phy_rf = rtl8723bu_init_phy_rf,
+ .phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection,
+ .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate,
+ .config_channel = rtl8xxxu_gen2_config_channel,
+ .parse_rx_desc = rtl8xxxu_parse_rxdesc24,
+ .init_aggregation = rtl8723bu_init_aggregation,
+ .init_statistics = rtl8723bu_init_statistics,
+ .enable_rf = rtl8723b_enable_rf,
+ .disable_rf = rtl8xxxu_gen2_disable_rf,
+ .usb_quirks = rtl8xxxu_gen2_usb_quirks,
+ .set_tx_power = rtl8723b_set_tx_power,
+ .update_rate_mask = rtl8xxxu_gen2_update_rate_mask,
+ .report_connect = rtl8xxxu_gen2_report_connect,
+ .writeN_block_size = 1024,
+ .mbox_ext_reg = REG_HMBOX_EXT0_8723B,
+ .mbox_ext_width = 4,
+ .tx_desc_size = sizeof(struct rtl8xxxu_txdesc40),
+ .rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24),
+ .has_s0s1 = 1,
+ .adda_1t_init = 0x01c00014,
+ .adda_1t_path_on = 0x01c00014,
+ .adda_2t_path_on_a = 0x01c00014,
+ .adda_2t_path_on_b = 0x01c00014,
+ .trxff_boundary = 0x3f7f,
+ .pbp_rx = PBP_PAGE_SIZE_256,
+ .pbp_tx = PBP_PAGE_SIZE_256,
+ .mactable = rtl8723b_mac_init_table,
+};
@@ -153,37 +153,6 @@ static struct rtl8xxxu_reg8val rtl8xxxu_gen1_mac_init_table[] = {
{0x70a, 0x65}, {0x70b, 0x87}, {0xffff, 0xff},
};
-static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = {
- {0x02f, 0x30}, {0x035, 0x00}, {0x039, 0x08}, {0x04e, 0xe0},
- {0x064, 0x00}, {0x067, 0x20}, {0x428, 0x0a}, {0x429, 0x10},
- {0x430, 0x00}, {0x431, 0x00},
- {0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05},
- {0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05},
- {0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01},
- {0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00},
- {0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f},
- {0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00},
- {0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f},
- {0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66},
- {0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff},
- {0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2},
- {0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3},
- {0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4},
- {0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4},
- {0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a},
- {0x516, 0x0a}, {0x525, 0x4f},
- {0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50},
- {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a},
- {0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff},
- {0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff},
- {0x638, 0x50}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e},
- {0x63f, 0x0e}, {0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00},
- {0x652, 0xc8}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43},
- {0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43},
- {0x70a, 0x65}, {0x70b, 0x87}, {0x765, 0x18}, {0x76e, 0x04},
- {0xffff, 0xff},
-};
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static struct rtl8xxxu_power_base rtl8188r_power_base = {
.reg_0e00 = 0x06080808,
@@ -350,107 +319,6 @@ static struct rtl8xxxu_reg32val rtl8723a_phy_1t_init_table[] = {
{0xffff, 0xffffffff},
};
-static struct rtl8xxxu_reg32val rtl8723b_phy_1t_init_table[] = {
- {0x800, 0x80040000}, {0x804, 0x00000003},
- {0x808, 0x0000fc00}, {0x80c, 0x0000000a},
- {0x810, 0x10001331}, {0x814, 0x020c3d10},
- {0x818, 0x02200385}, {0x81c, 0x00000000},
- {0x820, 0x01000100}, {0x824, 0x00190204},
- {0x828, 0x00000000}, {0x82c, 0x00000000},
- {0x830, 0x00000000}, {0x834, 0x00000000},
- {0x838, 0x00000000}, {0x83c, 0x00000000},
- {0x840, 0x00010000}, {0x844, 0x00000000},
- {0x848, 0x00000000}, {0x84c, 0x00000000},
- {0x850, 0x00000000}, {0x854, 0x00000000},
- {0x858, 0x569a11a9}, {0x85c, 0x01000014},
- {0x860, 0x66f60110}, {0x864, 0x061f0649},
- {0x868, 0x00000000}, {0x86c, 0x27272700},
- {0x870, 0x07000760}, {0x874, 0x25004000},
- {0x878, 0x00000808}, {0x87c, 0x00000000},
- {0x880, 0xb0000c1c}, {0x884, 0x00000001},
- {0x888, 0x00000000}, {0x88c, 0xccc000c0},
- {0x890, 0x00000800}, {0x894, 0xfffffffe},
- {0x898, 0x40302010}, {0x89c, 0x00706050},
- {0x900, 0x00000000}, {0x904, 0x00000023},
- {0x908, 0x00000000}, {0x90c, 0x81121111},
- {0x910, 0x00000002}, {0x914, 0x00000201},
- {0xa00, 0x00d047c8}, {0xa04, 0x80ff800c},
- {0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f},
- {0xa10, 0x9500bb78}, {0xa14, 0x1114d028},
- {0xa18, 0x00881117}, {0xa1c, 0x89140f00},
- {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317},
- {0xa28, 0x00000204}, {0xa2c, 0x00d30000},
- {0xa70, 0x101fbf00}, {0xa74, 0x00000007},
- {0xa78, 0x00000900}, {0xa7c, 0x225b0606},
- {0xa80, 0x21806490}, {0xb2c, 0x00000000},
- {0xc00, 0x48071d40}, {0xc04, 0x03a05611},
- {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c},
- {0xc10, 0x08800000}, {0xc14, 0x40000100},
- {0xc18, 0x08800000}, {0xc1c, 0x40000100},
- {0xc20, 0x00000000}, {0xc24, 0x00000000},
- {0xc28, 0x00000000}, {0xc2c, 0x00000000},
- {0xc30, 0x69e9ac44}, {0xc34, 0x469652af},
- {0xc38, 0x49795994}, {0xc3c, 0x0a97971c},
- {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7},
- {0xc48, 0xec020107}, {0xc4c, 0x007f037f},
- {0xc50, 0x69553420}, {0xc54, 0x43bc0094},
- {0xc58, 0x00013149}, {0xc5c, 0x00250492},
- {0xc60, 0x00000000}, {0xc64, 0x7112848b},
- {0xc68, 0x47c00bff}, {0xc6c, 0x00000036},
- {0xc70, 0x2c7f000d}, {0xc74, 0x020610db},
- {0xc78, 0x0000001f}, {0xc7c, 0x00b91612},
- {0xc80, 0x390000e4}, {0xc84, 0x20f60000},
- {0xc88, 0x40000100}, {0xc8c, 0x20200000},
- {0xc90, 0x00020e1a}, {0xc94, 0x00000000},
- {0xc98, 0x00020e1a}, {0xc9c, 0x00007f7f},
- {0xca0, 0x00000000}, {0xca4, 0x000300a0},
- {0xca8, 0x00000000}, {0xcac, 0x00000000},
- {0xcb0, 0x00000000}, {0xcb4, 0x00000000},
- {0xcb8, 0x00000000}, {0xcbc, 0x28000000},
- {0xcc0, 0x00000000}, {0xcc4, 0x00000000},
- {0xcc8, 0x00000000}, {0xccc, 0x00000000},
- {0xcd0, 0x00000000}, {0xcd4, 0x00000000},
- {0xcd8, 0x64b22427}, {0xcdc, 0x00766932},
- {0xce0, 0x00222222}, {0xce4, 0x00000000},
- {0xce8, 0x37644302}, {0xcec, 0x2f97d40c},
- {0xd00, 0x00000740}, {0xd04, 0x40020401},
- {0xd08, 0x0000907f}, {0xd0c, 0x20010201},
- {0xd10, 0xa0633333}, {0xd14, 0x3333bc53},
- {0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975},
- {0xd30, 0x00000000}, {0xd34, 0x80608000},
- {0xd38, 0x00000000}, {0xd3c, 0x00127353},
- {0xd40, 0x00000000}, {0xd44, 0x00000000},
- {0xd48, 0x00000000}, {0xd4c, 0x00000000},
- {0xd50, 0x6437140a}, {0xd54, 0x00000000},
- {0xd58, 0x00000282}, {0xd5c, 0x30032064},
- {0xd60, 0x4653de68}, {0xd64, 0x04518a3c},
- {0xd68, 0x00002101}, {0xd6c, 0x2a201c16},
- {0xd70, 0x1812362e}, {0xd74, 0x322c2220},
- {0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d},
- {0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d},
- {0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d},
- {0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d},
- {0xe28, 0x00000000}, {0xe30, 0x1000dc1f},
- {0xe34, 0x10008c1f}, {0xe38, 0x02140102},
- {0xe3c, 0x681604c2}, {0xe40, 0x01007c00},
- {0xe44, 0x01004800}, {0xe48, 0xfb000000},
- {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f},
- {0xe54, 0x10008c1f}, {0xe58, 0x02140102},
- {0xe5c, 0x28160d05}, {0xe60, 0x00000008},
- {0xe68, 0x001b2556}, {0xe6c, 0x00c00096},
- {0xe70, 0x00c00096}, {0xe74, 0x01000056},
- {0xe78, 0x01000014}, {0xe7c, 0x01000056},
- {0xe80, 0x01000014}, {0xe84, 0x00c00096},
- {0xe88, 0x01000056}, {0xe8c, 0x00c00096},
- {0xed0, 0x00c00096}, {0xed4, 0x00c00096},
- {0xed8, 0x00c00096}, {0xedc, 0x000000d6},
- {0xee0, 0x000000d6}, {0xeec, 0x01c00016},
- {0xf14, 0x00000003}, {0xf4c, 0x00000000},
- {0xf00, 0x00000300},
- {0x820, 0x01000100}, {0x800, 0x83040000},
- {0xffff, 0xffffffff},
-};
-
static struct rtl8xxxu_reg32val rtl8192cu_phy_2t_init_table[] = {
{0x024, 0x0011800f}, {0x028, 0x00ffdb83},
{0x800, 0x80040002}, {0x804, 0x00000003},
@@ -816,77 +684,6 @@ static struct rtl8xxxu_reg32val rtl8xxx_agc_highpa_table[] = {
{0xffff, 0xffffffff}
};
-static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = {
- {0xc78, 0xfd000001}, {0xc78, 0xfc010001},
- {0xc78, 0xfb020001}, {0xc78, 0xfa030001},
- {0xc78, 0xf9040001}, {0xc78, 0xf8050001},
- {0xc78, 0xf7060001}, {0xc78, 0xf6070001},
- {0xc78, 0xf5080001}, {0xc78, 0xf4090001},
- {0xc78, 0xf30a0001}, {0xc78, 0xf20b0001},
- {0xc78, 0xf10c0001}, {0xc78, 0xf00d0001},
- {0xc78, 0xef0e0001}, {0xc78, 0xee0f0001},
- {0xc78, 0xed100001}, {0xc78, 0xec110001},
- {0xc78, 0xeb120001}, {0xc78, 0xea130001},
- {0xc78, 0xe9140001}, {0xc78, 0xe8150001},
- {0xc78, 0xe7160001}, {0xc78, 0xe6170001},
- {0xc78, 0xe5180001}, {0xc78, 0xe4190001},
- {0xc78, 0xe31a0001}, {0xc78, 0xa51b0001},
- {0xc78, 0xa41c0001}, {0xc78, 0xa31d0001},
- {0xc78, 0x671e0001}, {0xc78, 0x661f0001},
- {0xc78, 0x65200001}, {0xc78, 0x64210001},
- {0xc78, 0x63220001}, {0xc78, 0x4a230001},
- {0xc78, 0x49240001}, {0xc78, 0x48250001},
- {0xc78, 0x47260001}, {0xc78, 0x46270001},
- {0xc78, 0x45280001}, {0xc78, 0x44290001},
- {0xc78, 0x432a0001}, {0xc78, 0x422b0001},
- {0xc78, 0x292c0001}, {0xc78, 0x282d0001},
- {0xc78, 0x272e0001}, {0xc78, 0x262f0001},
- {0xc78, 0x0a300001}, {0xc78, 0x09310001},
- {0xc78, 0x08320001}, {0xc78, 0x07330001},
- {0xc78, 0x06340001}, {0xc78, 0x05350001},
- {0xc78, 0x04360001}, {0xc78, 0x03370001},
- {0xc78, 0x02380001}, {0xc78, 0x01390001},
- {0xc78, 0x013a0001}, {0xc78, 0x013b0001},
- {0xc78, 0x013c0001}, {0xc78, 0x013d0001},
- {0xc78, 0x013e0001}, {0xc78, 0x013f0001},
- {0xc78, 0xfc400001}, {0xc78, 0xfb410001},
- {0xc78, 0xfa420001}, {0xc78, 0xf9430001},
- {0xc78, 0xf8440001}, {0xc78, 0xf7450001},
- {0xc78, 0xf6460001}, {0xc78, 0xf5470001},
- {0xc78, 0xf4480001}, {0xc78, 0xf3490001},
- {0xc78, 0xf24a0001}, {0xc78, 0xf14b0001},
- {0xc78, 0xf04c0001}, {0xc78, 0xef4d0001},
- {0xc78, 0xee4e0001}, {0xc78, 0xed4f0001},
- {0xc78, 0xec500001}, {0xc78, 0xeb510001},
- {0xc78, 0xea520001}, {0xc78, 0xe9530001},
- {0xc78, 0xe8540001}, {0xc78, 0xe7550001},
- {0xc78, 0xe6560001}, {0xc78, 0xe5570001},
- {0xc78, 0xe4580001}, {0xc78, 0xe3590001},
- {0xc78, 0xa65a0001}, {0xc78, 0xa55b0001},
- {0xc78, 0xa45c0001}, {0xc78, 0xa35d0001},
- {0xc78, 0x675e0001}, {0xc78, 0x665f0001},
- {0xc78, 0x65600001}, {0xc78, 0x64610001},
- {0xc78, 0x63620001}, {0xc78, 0x62630001},
- {0xc78, 0x61640001}, {0xc78, 0x48650001},
- {0xc78, 0x47660001}, {0xc78, 0x46670001},
- {0xc78, 0x45680001}, {0xc78, 0x44690001},
- {0xc78, 0x436a0001}, {0xc78, 0x426b0001},
- {0xc78, 0x286c0001}, {0xc78, 0x276d0001},
- {0xc78, 0x266e0001}, {0xc78, 0x256f0001},
- {0xc78, 0x24700001}, {0xc78, 0x09710001},
- {0xc78, 0x08720001}, {0xc78, 0x07730001},
- {0xc78, 0x06740001}, {0xc78, 0x05750001},
- {0xc78, 0x04760001}, {0xc78, 0x03770001},
- {0xc78, 0x02780001}, {0xc78, 0x01790001},
- {0xc78, 0x017a0001}, {0xc78, 0x017b0001},
- {0xc78, 0x017c0001}, {0xc78, 0x017d0001},
- {0xc78, 0x017e0001}, {0xc78, 0x017f0001},
- {0xc50, 0x69553422},
- {0xc50, 0x69553420},
- {0x824, 0x00390204},
- {0xffff, 0xffffffff}
-};
-
static struct rtl8xxxu_rfregval rtl8723au_radioa_1t_init_table[] = {
{0x00, 0x00030159}, {0x01, 0x00031284},
{0x02, 0x00098000}, {0x03, 0x00039c63},
@@ -962,75 +759,6 @@ static struct rtl8xxxu_rfregval rtl8723au_radioa_1t_init_table[] = {
{0xff, 0xffffffff}
};
-static struct rtl8xxxu_rfregval rtl8723bu_radioa_1t_init_table[] = {
- {0x00, 0x00010000}, {0xb0, 0x000dffe0},
- {0xfe, 0x00000000}, {0xfe, 0x00000000},
- {0xfe, 0x00000000}, {0xb1, 0x00000018},
- {0xfe, 0x00000000}, {0xfe, 0x00000000},
- {0xfe, 0x00000000}, {0xb2, 0x00084c00},
- {0xb5, 0x0000d2cc}, {0xb6, 0x000925aa},
- {0xb7, 0x00000010}, {0xb8, 0x0000907f},
- {0x5c, 0x00000002}, {0x7c, 0x00000002},
- {0x7e, 0x00000005}, {0x8b, 0x0006fc00},
- {0xb0, 0x000ff9f0}, {0x1c, 0x000739d2},
- {0x1e, 0x00000000}, {0xdf, 0x00000780},
- {0x50, 0x00067435},
- /*
- * The 8723bu vendor driver indicates that bit 8 should be set in
- * 0x51 for package types TFBGA90, TFBGA80, and TFBGA79. However
- * they never actually check the package type - and just default
- * to not setting it.
- */
- {0x51, 0x0006b04e},
- {0x52, 0x000007d2}, {0x53, 0x00000000},
- {0x54, 0x00050400}, {0x55, 0x0004026e},
- {0xdd, 0x0000004c}, {0x70, 0x00067435},
- /*
- * 0x71 has same package type condition as for register 0x51
- */
- {0x71, 0x0006b04e},
- {0x72, 0x000007d2}, {0x73, 0x00000000},
- {0x74, 0x00050400}, {0x75, 0x0004026e},
- {0xef, 0x00000100}, {0x34, 0x0000add7},
- {0x35, 0x00005c00}, {0x34, 0x00009dd4},
- {0x35, 0x00005000}, {0x34, 0x00008dd1},
- {0x35, 0x00004400}, {0x34, 0x00007dce},
- {0x35, 0x00003800}, {0x34, 0x00006cd1},
- {0x35, 0x00004400}, {0x34, 0x00005cce},
- {0x35, 0x00003800}, {0x34, 0x000048ce},
- {0x35, 0x00004400}, {0x34, 0x000034ce},
- {0x35, 0x00003800}, {0x34, 0x00002451},
- {0x35, 0x00004400}, {0x34, 0x0000144e},
- {0x35, 0x00003800}, {0x34, 0x00000051},
- {0x35, 0x00004400}, {0xef, 0x00000000},
- {0xef, 0x00000100}, {0xed, 0x00000010},
- {0x44, 0x0000add7}, {0x44, 0x00009dd4},
- {0x44, 0x00008dd1}, {0x44, 0x00007dce},
- {0x44, 0x00006cc1}, {0x44, 0x00005cce},
- {0x44, 0x000044d1}, {0x44, 0x000034ce},
- {0x44, 0x00002451}, {0x44, 0x0000144e},
- {0x44, 0x00000051}, {0xef, 0x00000000},
- {0xed, 0x00000000}, {0x7f, 0x00020080},
- {0xef, 0x00002000}, {0x3b, 0x000380ef},
- {0x3b, 0x000302fe}, {0x3b, 0x00028ce6},
- {0x3b, 0x000200bc}, {0x3b, 0x000188a5},
- {0x3b, 0x00010fbc}, {0x3b, 0x00008f71},
- {0x3b, 0x00000900}, {0xef, 0x00000000},
- {0xed, 0x00000001}, {0x40, 0x000380ef},
- {0x40, 0x000302fe}, {0x40, 0x00028ce6},
- {0x40, 0x000200bc}, {0x40, 0x000188a5},
- {0x40, 0x00010fbc}, {0x40, 0x00008f71},
- {0x40, 0x00000900}, {0xed, 0x00000000},
- {0x82, 0x00080000}, {0x83, 0x00008000},
- {0x84, 0x00048d80}, {0x85, 0x00068000},
- {0xa2, 0x00080000}, {0xa3, 0x00008000},
- {0xa4, 0x00048d80}, {0xa5, 0x00068000},
- {0xed, 0x00000002}, {0xef, 0x00000002},
- {0x56, 0x00000032}, {0x76, 0x00000032},
- {0x01, 0x00000780},
- {0xff, 0xffffffff}
-};
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static struct rtl8xxxu_rfregval rtl8192cu_radioa_2t_init_table[] = {
{0x00, 0x00030159}, {0x01, 0x00031284},
@@ -1553,8 +1281,7 @@ int rtl8xxxu_write_rfreg(struct rtl8xxxu_priv *priv,
return retval;
}
-static int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv,
- struct h2c_cmd *h2c, int len)
+int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv, struct h2c_cmd *h2c, int len)
{
struct device *dev = &priv->udev->dev;
int mbox_nr, retry, retval = 0;
@@ -1613,27 +1340,6 @@ error:
return retval;
}
-static void rtl8723bu_write_btreg(struct rtl8xxxu_priv *priv, u8 reg, u8 data)
-{
- struct h2c_cmd h2c;
- int reqnum = 0;
-
- memset(&h2c, 0, sizeof(struct h2c_cmd));
- h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER;
- h2c.bt_mp_oper.operreq = 0 | (reqnum << 4);
- h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE;
- h2c.bt_mp_oper.data = data;
- rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper));
-
- reqnum++;
- memset(&h2c, 0, sizeof(struct h2c_cmd));
- h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER;
- h2c.bt_mp_oper.operreq = 0 | (reqnum << 4);
- h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE;
- h2c.bt_mp_oper.addr = reg;
- rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper));
-}
-
static void rtl8xxxu_gen1_enable_rf(struct rtl8xxxu_priv *priv)
{
u8 val8;
@@ -2163,45 +1869,6 @@ rtl8xxxu_gen1_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40)
}
}
-static void
-rtl8723b_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40)
-{
- u32 val32, ofdm, mcs;
- u8 cck, ofdmbase, mcsbase;
- int group, tx_idx;
-
- tx_idx = 0;
- group = rtl8xxxu_gen2_channel_to_group(channel);
-
- cck = priv->cck_tx_power_index_B[group];
- val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32);
- val32 &= 0xffff00ff;
- val32 |= (cck << 8);
- rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11);
- val32 &= 0xff;
- val32 |= ((cck << 8) | (cck << 16) | (cck << 24));
- rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32);
-
- ofdmbase = priv->ht40_1s_tx_power_index_B[group];
- ofdmbase += priv->ofdm_tx_power_diff[tx_idx].b;
- ofdm = ofdmbase | ofdmbase << 8 | ofdmbase << 16 | ofdmbase << 24;
-
- rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm);
- rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm);
-
- mcsbase = priv->ht40_1s_tx_power_index_B[group];
- if (ht40)
- mcsbase += priv->ht40_tx_power_diff[tx_idx++].b;
- else
- mcsbase += priv->ht20_tx_power_diff[tx_idx++].b;
- mcs = mcsbase | mcsbase << 8 | mcsbase << 16 | mcsbase << 24;
-
- rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs);
- rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs);
-}
-
static void rtl8xxxu_set_linktype(struct rtl8xxxu_priv *priv,
enum nl80211_iftype linktype)
{
@@ -2494,83 +2161,6 @@ static int rtl8723au_parse_efuse(struct rtl8xxxu_priv *priv)
return 0;
}
-static int rtl8723bu_parse_efuse(struct rtl8xxxu_priv *priv)
-{
- struct rtl8723bu_efuse *efuse = &priv->efuse_wifi.efuse8723bu;
- int i;
-
- if (efuse->rtl_id != cpu_to_le16(0x8129))
- return -EINVAL;
-
- ether_addr_copy(priv->mac_addr, efuse->mac_addr);
-
- memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base,
- sizeof(efuse->tx_power_index_A.cck_base));
- memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base,
- sizeof(efuse->tx_power_index_B.cck_base));
-
- memcpy(priv->ht40_1s_tx_power_index_A,
- efuse->tx_power_index_A.ht40_base,
- sizeof(efuse->tx_power_index_A.ht40_base));
- memcpy(priv->ht40_1s_tx_power_index_B,
- efuse->tx_power_index_B.ht40_base,
- sizeof(efuse->tx_power_index_B.ht40_base));
-
- priv->ofdm_tx_power_diff[0].a =
- efuse->tx_power_index_A.ht20_ofdm_1s_diff.a;
- priv->ofdm_tx_power_diff[0].b =
- efuse->tx_power_index_B.ht20_ofdm_1s_diff.a;
-
- priv->ht20_tx_power_diff[0].a =
- efuse->tx_power_index_A.ht20_ofdm_1s_diff.b;
- priv->ht20_tx_power_diff[0].b =
- efuse->tx_power_index_B.ht20_ofdm_1s_diff.b;
-
- priv->ht40_tx_power_diff[0].a = 0;
- priv->ht40_tx_power_diff[0].b = 0;
-
- for (i = 1; i < RTL8723B_TX_COUNT; i++) {
- priv->ofdm_tx_power_diff[i].a =
- efuse->tx_power_index_A.pwr_diff[i - 1].ofdm;
- priv->ofdm_tx_power_diff[i].b =
- efuse->tx_power_index_B.pwr_diff[i - 1].ofdm;
-
- priv->ht20_tx_power_diff[i].a =
- efuse->tx_power_index_A.pwr_diff[i - 1].ht20;
- priv->ht20_tx_power_diff[i].b =
- efuse->tx_power_index_B.pwr_diff[i - 1].ht20;
-
- priv->ht40_tx_power_diff[i].a =
- efuse->tx_power_index_A.pwr_diff[i - 1].ht40;
- priv->ht40_tx_power_diff[i].b =
- efuse->tx_power_index_B.pwr_diff[i - 1].ht40;
- }
-
- priv->has_xtalk = 1;
- priv->xtalk = priv->efuse_wifi.efuse8723bu.xtal_k & 0x3f;
-
- dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name);
- dev_info(&priv->udev->dev, "Product: %.41s\n", efuse->device_name);
-
- if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) {
- int i;
- unsigned char *raw = priv->efuse_wifi.raw;
-
- dev_info(&priv->udev->dev,
- "%s: dumping efuse (0x%02zx bytes):\n",
- __func__, sizeof(struct rtl8723bu_efuse));
- for (i = 0; i < sizeof(struct rtl8723bu_efuse); i += 8) {
- dev_info(&priv->udev->dev, "%02x: "
- "%02x %02x %02x %02x %02x %02x %02x %02x\n", i,
- raw[i], raw[i + 1], raw[i + 2],
- raw[i + 3], raw[i + 4], raw[i + 5],
- raw[i + 6], raw[i + 7]);
- }
- }
-
- return 0;
-}
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static int rtl8192cu_parse_efuse(struct rtl8xxxu_priv *priv)
@@ -2816,35 +2406,6 @@ void rtl8xxxu_reset_8051(struct rtl8xxxu_priv *priv)
rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
}
-static void rtl8723bu_reset_8051(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- u16 sys_func;
-
- val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL);
- val8 &= ~BIT(1);
- rtl8xxxu_write8(priv, REG_RSV_CTRL, val8);
-
- val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
- val8 &= ~BIT(0);
- rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
-
- sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC);
- sys_func &= ~SYS_FUNC_CPU_ENABLE;
- rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
-
- val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL);
- val8 &= ~BIT(1);
- rtl8xxxu_write8(priv, REG_RSV_CTRL, val8);
-
- val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
- val8 |= BIT(0);
- rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
-
- sys_func |= SYS_FUNC_CPU_ENABLE;
- rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
-}
-
static int rtl8xxxu_start_firmware(struct rtl8xxxu_priv *priv)
{
struct device *dev = &priv->udev->dev;
@@ -3053,20 +2614,6 @@ static int rtl8723au_load_firmware(struct rtl8xxxu_priv *priv)
return ret;
}
-static int rtl8723bu_load_firmware(struct rtl8xxxu_priv *priv)
-{
- char *fw_name;
- int ret;
-
- if (priv->enable_bluetooth)
- fw_name = "rtlwifi/rtl8723bu_bt.bin";
- else
- fw_name = "rtlwifi/rtl8723bu_nic.bin";
-
- ret = rtl8xxxu_load_firmware(priv, fw_name);
- return ret;
-}
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static int rtl8192cu_load_firmware(struct rtl8xxxu_priv *priv)
@@ -3088,7 +2635,7 @@ static int rtl8192cu_load_firmware(struct rtl8xxxu_priv *priv)
#endif
-static void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv)
+void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv)
{
u16 val16;
int i = 100;
@@ -3115,44 +2662,6 @@ static void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv)
}
}
-static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv)
-{
- u32 val32;
-
- val32 = rtl8xxxu_read32(priv, REG_PAD_CTRL1);
- val32 &= ~(BIT(20) | BIT(24));
- rtl8xxxu_write32(priv, REG_PAD_CTRL1, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
- val32 &= ~BIT(4);
- rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
- val32 |= BIT(3);
- rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
- val32 |= BIT(24);
- rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
- val32 &= ~BIT(23);
- rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER);
- val32 |= (BIT(0) | BIT(1));
- rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_RFE_CTRL_ANTA_SRC);
- val32 &= 0xffffff00;
- val32 |= 0x77;
- rtl8xxxu_write32(priv, REG_RFE_CTRL_ANTA_SRC, val32);
-
- val32 = rtl8xxxu_read32(priv, REG_PWR_DATA);
- val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
- rtl8xxxu_write32(priv, REG_PWR_DATA, val32);
-}
-
static int
rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv)
{
@@ -3262,29 +2771,6 @@ static void rtl8xxxu_gen1_init_phy_bb(struct rtl8xxxu_priv *priv)
rtl8xxxu_write32(priv, REG_LDOA15_CTRL, val32);
}
-static void rtl8723bu_init_phy_bb(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- u16 val16;
-
- val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
- val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | SYS_FUNC_DIO_RF;
- rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
-
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
-
- /* 6. 0x1f[7:0] = 0x07 */
- val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
- rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
-
- /* Why? */
- rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3);
- rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80);
- rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table);
-
- rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table);
-}
-
/*
* Most of this is black magic retrieved from the old rtl8723au driver
*/
@@ -3499,22 +2985,6 @@ static int rtl8723au_init_phy_rf(struct rtl8xxxu_priv *priv)
return ret;
}
-static int rtl8723bu_init_phy_rf(struct rtl8xxxu_priv *priv)
-{
- int ret;
-
- ret = rtl8xxxu_init_phy_rf(priv, rtl8723bu_radioa_1t_init_table, RF_A);
- /*
- * PHY LCK
- */
- rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdfbe0);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, 0x8c01);
- msleep(200);
- rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdffe0);
-
- return ret;
-}
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static int rtl8192cu_init_phy_rf(struct rtl8xxxu_priv *priv)
{
@@ -4199,356 +3669,37 @@ out:
return result;
}
-static int rtl8723bu_iqk_path_a(struct rtl8xxxu_priv *priv)
+static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
+ int result[][8], int t)
{
- u32 reg_eac, reg_e94, reg_e9c, path_sel, val32;
- int result = 0;
-
- path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
-
- /*
- * Leave IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /*
- * Enable path A PA in TX IQK mode
- */
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
- val32 |= 0x80000;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x20000);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0003f);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xc7f87);
+ struct device *dev = &priv->udev->dev;
+ u32 i, val32;
+ int path_a_ok, path_b_ok;
+ int retry = 2;
+ const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
+ REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
+ REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
+ REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
+ REG_TX_OFDM_BBON, REG_TX_TO_RX,
+ REG_TX_TO_TX, REG_RX_CCK,
+ REG_RX_OFDM, REG_RX_WAIT_RIFS,
+ REG_RX_TO_RX, REG_STANDBY,
+ REG_SLEEP, REG_PMPD_ANAEN
+ };
+ const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
+ REG_TXPAUSE, REG_BEACON_CTRL,
+ REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
+ };
+ const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
+ REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
+ REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
+ REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
+ REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE
+ };
/*
- * Tx IQK setting
- */
- rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
- rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
-
- /* path-A IQK setting */
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
-
- rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x821403ea);
- rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000);
- rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
- rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
-
- /* LO calibration setting */
- rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911);
-
- /*
- * Enter IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- val32 |= 0x80800000;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /*
- * The vendor driver indicates the USB module is always using
- * S0S1 path 1 for the 8723bu. This may be different for 8192eu
- */
- if (priv->rf_paths > 1)
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
- else
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
-
- /*
- * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu.
- * No trace of this in the 8192eu or 8188eu vendor drivers.
- */
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
-
- /* One shot, path A LOK & IQK */
- rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
- rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
-
- mdelay(1);
-
- /* Restore Ant Path */
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
-#ifdef RTL8723BU_BT
- /* GNT_BT = 1 */
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
-#endif
-
- /*
- * Leave IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /* Check failed */
- reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
- reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
- reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
-
- val32 = (reg_e9c >> 16) & 0x3ff;
- if (val32 & 0x200)
- val32 = 0x400 - val32;
-
- if (!(reg_eac & BIT(28)) &&
- ((reg_e94 & 0x03ff0000) != 0x01420000) &&
- ((reg_e9c & 0x03ff0000) != 0x00420000) &&
- ((reg_e94 & 0x03ff0000) < 0x01100000) &&
- ((reg_e94 & 0x03ff0000) > 0x00f00000) &&
- val32 < 0xf)
- result |= 0x01;
- else /* If TX not OK, ignore RX */
- goto out;
-
-out:
- return result;
-}
-
-static int rtl8723bu_rx_iqk_path_a(struct rtl8xxxu_priv *priv)
-{
- u32 reg_ea4, reg_eac, reg_e94, reg_e9c, path_sel, val32;
- int result = 0;
-
- path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
-
- /*
- * Leave IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /*
- * Enable path A PA in TX IQK mode
- */
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
- val32 |= 0x80000;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7);
-
- /*
- * Tx IQK setting
- */
- rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
- rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
-
- /* path-A IQK setting */
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
-
- rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160ff0);
- rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000);
- rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
- rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
-
- /* LO calibration setting */
- rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
-
- /*
- * Enter IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- val32 |= 0x80800000;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /*
- * The vendor driver indicates the USB module is always using
- * S0S1 path 1 for the 8723bu. This may be different for 8192eu
- */
- if (priv->rf_paths > 1)
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
- else
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
-
- /*
- * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu.
- * No trace of this in the 8192eu or 8188eu vendor drivers.
- */
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
-
- /* One shot, path A LOK & IQK */
- rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
- rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
-
- mdelay(1);
-
- /* Restore Ant Path */
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
-#ifdef RTL8723BU_BT
- /* GNT_BT = 1 */
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
-#endif
-
- /*
- * Leave IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /* Check failed */
- reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
- reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
- reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
-
- val32 = (reg_e9c >> 16) & 0x3ff;
- if (val32 & 0x200)
- val32 = 0x400 - val32;
-
- if (!(reg_eac & BIT(28)) &&
- ((reg_e94 & 0x03ff0000) != 0x01420000) &&
- ((reg_e9c & 0x03ff0000) != 0x00420000) &&
- ((reg_e94 & 0x03ff0000) < 0x01100000) &&
- ((reg_e94 & 0x03ff0000) > 0x00f00000) &&
- val32 < 0xf)
- result |= 0x01;
- else /* If TX not OK, ignore RX */
- goto out;
-
- val32 = 0x80007c00 | (reg_e94 &0x3ff0000) |
- ((reg_e9c & 0x3ff0000) >> 16);
- rtl8xxxu_write32(priv, REG_TX_IQK, val32);
-
- /*
- * Modify RX IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
- val32 |= 0x80000;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7d77);
-
- /*
- * PA, PAD setting
- */
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0xf80);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_55, 0x4021f);
-
- /*
- * RX IQK setting
- */
- rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
-
- /* path-A IQK setting */
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c);
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
-
- rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82110000);
- rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x2816001f);
- rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
- rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
-
- /* LO calibration setting */
- rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a8d1);
-
- /*
- * Enter IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- val32 |= 0x80800000;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- if (priv->rf_paths > 1)
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
- else
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
-
- /*
- * Disable BT
- */
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
-
- /* One shot, path A LOK & IQK */
- rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
- rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
-
- mdelay(1);
-
- /* Restore Ant Path */
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
-#ifdef RTL8723BU_BT
- /* GNT_BT = 1 */
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
-#endif
-
- /*
- * Leave IQK mode
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /* Check failed */
- reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
- reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2);
-
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x780);
-
- val32 = (reg_eac >> 16) & 0x3ff;
- if (val32 & 0x200)
- val32 = 0x400 - val32;
-
- if (!(reg_eac & BIT(27)) &&
- ((reg_ea4 & 0x03ff0000) != 0x01320000) &&
- ((reg_eac & 0x03ff0000) != 0x00360000) &&
- ((reg_ea4 & 0x03ff0000) < 0x01100000) &&
- ((reg_ea4 & 0x03ff0000) > 0x00f00000) &&
- val32 < 0xf)
- result |= 0x02;
- else /* If TX not OK, ignore RX */
- goto out;
-out:
- return result;
-}
-
-static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
- int result[][8], int t)
-{
- struct device *dev = &priv->udev->dev;
- u32 i, val32;
- int path_a_ok, path_b_ok;
- int retry = 2;
- const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
- REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
- REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
- REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
- REG_TX_OFDM_BBON, REG_TX_TO_RX,
- REG_TX_TO_TX, REG_RX_CCK,
- REG_RX_OFDM, REG_RX_WAIT_RIFS,
- REG_RX_TO_RX, REG_STANDBY,
- REG_SLEEP, REG_PMPD_ANAEN
- };
- const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
- REG_TXPAUSE, REG_BEACON_CTRL,
- REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
- };
- const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
- REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
- REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
- REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
- REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE
- };
-
- /*
- * Note: IQ calibration must be performed after loading
- * PHY_REG.txt , and radio_a, radio_b.txt
+ * Note: IQ calibration must be performed after loading
+ * PHY_REG.txt , and radio_a, radio_b.txt
*/
if (t == 0) {
@@ -4723,215 +3874,7 @@ static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
}
}
-static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
- int result[][8], int t)
-{
- struct device *dev = &priv->udev->dev;
- u32 i, val32;
- int path_a_ok /*, path_b_ok */;
- int retry = 2;
- const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
- REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
- REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
- REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
- REG_TX_OFDM_BBON, REG_TX_TO_RX,
- REG_TX_TO_TX, REG_RX_CCK,
- REG_RX_OFDM, REG_RX_WAIT_RIFS,
- REG_RX_TO_RX, REG_STANDBY,
- REG_SLEEP, REG_PMPD_ANAEN
- };
- const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
- REG_TXPAUSE, REG_BEACON_CTRL,
- REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
- };
- const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
- REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
- REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
- REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
- REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE
- };
- u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff;
- u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff;
-
- /*
- * Note: IQ calibration must be performed after loading
- * PHY_REG.txt , and radio_a, radio_b.txt
- */
-
- if (t == 0) {
- /* Save ADDA parameters, turn Path A ADDA on */
- rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup,
- RTL8XXXU_ADDA_REGS);
- rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
- rtl8xxxu_save_regs(priv, iqk_bb_regs,
- priv->bb_backup, RTL8XXXU_BB_REGS);
- }
-
- rtl8xxxu_path_adda_on(priv, adda_regs, true);
-
- /* MAC settings */
- rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup);
-
- val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING);
- val32 |= 0x0f000000;
- rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32);
-
- rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600);
- rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
- rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000);
-
- /*
- * RX IQ calibration setting for 8723B D cut large current issue
- * when leaving IPS
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
- val32 |= 0x80000;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
-
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7);
-
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED);
- val32 |= 0x20;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
-
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_43, 0x60fbd);
-
- for (i = 0; i < retry; i++) {
- path_a_ok = rtl8723bu_iqk_path_a(priv);
- if (path_a_ok == 0x01) {
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- val32 = rtl8xxxu_read32(priv,
- REG_TX_POWER_BEFORE_IQK_A);
- result[t][0] = (val32 >> 16) & 0x3ff;
- val32 = rtl8xxxu_read32(priv,
- REG_TX_POWER_AFTER_IQK_A);
- result[t][1] = (val32 >> 16) & 0x3ff;
-
- break;
- }
- }
-
- if (!path_a_ok)
- dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__);
-
- for (i = 0; i < retry; i++) {
- path_a_ok = rtl8723bu_rx_iqk_path_a(priv);
- if (path_a_ok == 0x03) {
- val32 = rtl8xxxu_read32(priv,
- REG_RX_POWER_BEFORE_IQK_A_2);
- result[t][2] = (val32 >> 16) & 0x3ff;
- val32 = rtl8xxxu_read32(priv,
- REG_RX_POWER_AFTER_IQK_A_2);
- result[t][3] = (val32 >> 16) & 0x3ff;
-
- break;
- }
- }
-
- if (!path_a_ok)
- dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__);
-
- if (priv->tx_paths > 1) {
-#if 1
- dev_warn(dev, "%s: Path B not supported\n", __func__);
-#else
-
- /*
- * Path A into standby
- */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000);
-
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- val32 |= 0x80800000;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- /* Turn Path B ADDA on */
- rtl8xxxu_path_adda_on(priv, adda_regs, false);
-
- for (i = 0; i < retry; i++) {
- path_b_ok = rtl8xxxu_iqk_path_b(priv);
- if (path_b_ok == 0x03) {
- val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
- result[t][4] = (val32 >> 16) & 0x3ff;
- val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
- result[t][5] = (val32 >> 16) & 0x3ff;
- break;
- }
- }
-
- if (!path_b_ok)
- dev_dbg(dev, "%s: Path B IQK failed!\n", __func__);
-
- for (i = 0; i < retry; i++) {
- path_b_ok = rtl8723bu_rx_iqk_path_b(priv);
- if (path_a_ok == 0x03) {
- val32 = rtl8xxxu_read32(priv,
- REG_RX_POWER_BEFORE_IQK_B_2);
- result[t][6] = (val32 >> 16) & 0x3ff;
- val32 = rtl8xxxu_read32(priv,
- REG_RX_POWER_AFTER_IQK_B_2);
- result[t][7] = (val32 >> 16) & 0x3ff;
- break;
- }
- }
-
- if (!path_b_ok)
- dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__);
-#endif
- }
-
- /* Back to BB mode, load original value */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 &= 0x000000ff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
- if (t) {
- /* Reload ADDA power saving parameters */
- rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup,
- RTL8XXXU_ADDA_REGS);
-
- /* Reload MAC parameters */
- rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
-
- /* Reload BB parameters */
- rtl8xxxu_restore_regs(priv, iqk_bb_regs,
- priv->bb_backup, RTL8XXXU_BB_REGS);
-
- /* Restore RX initial gain */
- val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1);
- val32 &= 0xffffff00;
- rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50);
- rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc);
-
- if (priv->tx_paths > 1) {
- val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1);
- val32 &= 0xffffff00;
- rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
- val32 | 0x50);
- rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
- val32 | xb_agc);
- }
-
- /* Load 0xe30 IQC default value */
- rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00);
- rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00);
- }
-}
-
-static void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start)
+void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start)
{
struct h2c_cmd h2c;
@@ -5049,130 +3992,6 @@ static void rtl8xxxu_gen1_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
rtl8xxxu_prepare_calibrate(priv, 0);
}
-static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
-{
- struct device *dev = &priv->udev->dev;
- int result[4][8]; /* last is final result */
- int i, candidate;
- bool path_a_ok, path_b_ok;
- u32 reg_e94, reg_e9c, reg_ea4, reg_eac;
- u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc;
- u32 val32, bt_control;
- s32 reg_tmp = 0;
- bool simu;
-
- rtl8xxxu_prepare_calibrate(priv, 1);
-
- memset(result, 0, sizeof(result));
- candidate = -1;
-
- path_a_ok = false;
- path_b_ok = false;
-
- bt_control = rtl8xxxu_read32(priv, REG_BT_CONTROL_8723BU);
-
- for (i = 0; i < 3; i++) {
- rtl8723bu_phy_iqcalibrate(priv, result, i);
-
- if (i == 1) {
- simu = rtl8xxxu_gen2_simularity_compare(priv,
- result, 0, 1);
- if (simu) {
- candidate = 0;
- break;
- }
- }
-
- if (i == 2) {
- simu = rtl8xxxu_gen2_simularity_compare(priv,
- result, 0, 2);
- if (simu) {
- candidate = 0;
- break;
- }
-
- simu = rtl8xxxu_gen2_simularity_compare(priv,
- result, 1, 2);
- if (simu) {
- candidate = 1;
- } else {
- for (i = 0; i < 8; i++)
- reg_tmp += result[3][i];
-
- if (reg_tmp)
- candidate = 3;
- else
- candidate = -1;
- }
- }
- }
-
- for (i = 0; i < 4; i++) {
- reg_e94 = result[i][0];
- reg_e9c = result[i][1];
- reg_ea4 = result[i][2];
- reg_eac = result[i][3];
- reg_eb4 = result[i][4];
- reg_ebc = result[i][5];
- reg_ec4 = result[i][6];
- reg_ecc = result[i][7];
- }
-
- if (candidate >= 0) {
- reg_e94 = result[candidate][0];
- priv->rege94 = reg_e94;
- reg_e9c = result[candidate][1];
- priv->rege9c = reg_e9c;
- reg_ea4 = result[candidate][2];
- reg_eac = result[candidate][3];
- reg_eb4 = result[candidate][4];
- priv->regeb4 = reg_eb4;
- reg_ebc = result[candidate][5];
- priv->regebc = reg_ebc;
- reg_ec4 = result[candidate][6];
- reg_ecc = result[candidate][7];
- dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate);
- dev_dbg(dev,
- "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x "
- "ecc=%x\n ", __func__, reg_e94, reg_e9c,
- reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc);
- path_a_ok = true;
- path_b_ok = true;
- } else {
- reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100;
- reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0;
- }
-
- if (reg_e94 && candidate >= 0)
- rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result,
- candidate, (reg_ea4 == 0));
-
- if (priv->tx_paths > 1 && reg_eb4)
- rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result,
- candidate, (reg_ec4 == 0));
-
- rtl8xxxu_save_regs(priv, rtl8xxxu_iqk_phy_iq_bb_reg,
- priv->bb_recovery_backup, RTL8XXXU_BB_REGS);
-
- rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, bt_control);
-
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
- val32 |= 0x80000;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x18000);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xe6177);
- val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED);
- val32 |= 0x20;
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
- rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd);
-
- if (priv->rf_paths > 1)
- dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__);
-
- rtl8xxxu_prepare_calibrate(priv, 0);
-}
-
static void rtl8723a_phy_lc_calibrate(struct rtl8xxxu_priv *priv)
{
u32 val32;
@@ -5274,92 +4093,39 @@ rtl8xxxu_set_ampdu_factor(struct rtl8xxxu_priv *priv, u8 ampdu_factor)
for (i = 0; i < 4; i++) {
if ((vals[i] & 0xf0) > (ampdu_factor << 4))
- vals[i] = (vals[i] & 0x0f) | (ampdu_factor << 4);
-
- if ((vals[i] & 0x0f) > ampdu_factor)
- vals[i] = (vals[i] & 0xf0) | ampdu_factor;
-
- rtl8xxxu_write8(priv, REG_AGGLEN_LMT + i, vals[i]);
- }
-}
-
-static void rtl8xxxu_set_ampdu_min_space(struct rtl8xxxu_priv *priv, u8 density)
-{
- u8 val8;
-
- val8 = rtl8xxxu_read8(priv, REG_AMPDU_MIN_SPACE);
- val8 &= 0xf8;
- val8 |= density;
- rtl8xxxu_write8(priv, REG_AMPDU_MIN_SPACE, val8);
-}
-
-static int rtl8xxxu_active_to_emu(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- int count, ret = 0;
-
- /* Start of rtl8723AU_card_enable_flow */
- /* Act to Cardemu sequence*/
- /* Turn off RF */
- rtl8xxxu_write8(priv, REG_RF_CTRL, 0);
-
- /* 0x004E[7] = 0, switch DPDT_SEL_P output from register 0x0065[2] */
- val8 = rtl8xxxu_read8(priv, REG_LEDCFG2);
- val8 &= ~LEDCFG2_DPDT_SELECT;
- rtl8xxxu_write8(priv, REG_LEDCFG2, val8);
-
- /* 0x0005[1] = 1 turn off MAC by HW state machine*/
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- val8 |= BIT(1);
- rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
-
- for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- if ((val8 & BIT(1)) == 0)
- break;
- udelay(10);
- }
-
- if (!count) {
- dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n",
- __func__);
- ret = -EBUSY;
- goto exit;
- }
+ vals[i] = (vals[i] & 0x0f) | (ampdu_factor << 4);
- /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */
- val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
- val8 |= SYS_ISO_ANALOG_IPS;
- rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
+ if ((vals[i] & 0x0f) > ampdu_factor)
+ vals[i] = (vals[i] & 0xf0) | ampdu_factor;
- /* 0x0020[0] = 0 disable LDOA12 MACRO block*/
- val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
- val8 &= ~LDOA15_ENABLE;
- rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
+ rtl8xxxu_write8(priv, REG_AGGLEN_LMT + i, vals[i]);
+ }
+}
-exit:
- return ret;
+static void rtl8xxxu_set_ampdu_min_space(struct rtl8xxxu_priv *priv, u8 density)
+{
+ u8 val8;
+
+ val8 = rtl8xxxu_read8(priv, REG_AMPDU_MIN_SPACE);
+ val8 &= 0xf8;
+ val8 |= density;
+ rtl8xxxu_write8(priv, REG_AMPDU_MIN_SPACE, val8);
}
-static int rtl8723bu_active_to_emu(struct rtl8xxxu_priv *priv)
+static int rtl8xxxu_active_to_emu(struct rtl8xxxu_priv *priv)
{
u8 val8;
- u16 val16;
- u32 val32;
int count, ret = 0;
+ /* Start of rtl8723AU_card_enable_flow */
+ /* Act to Cardemu sequence*/
/* Turn off RF */
rtl8xxxu_write8(priv, REG_RF_CTRL, 0);
- /* Enable rising edge triggering interrupt */
- val16 = rtl8xxxu_read16(priv, REG_GPIO_INTM);
- val16 &= ~GPIO_INTM_EDGE_TRIG_IRQ;
- rtl8xxxu_write16(priv, REG_GPIO_INTM, val16);
-
- /* Release WLON reset 0x04[16]= 1*/
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- val32 |= APS_FSMCO_WLON_RESET;
- rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
+ /* 0x004E[7] = 0, switch DPDT_SEL_P output from register 0x0065[2] */
+ val8 = rtl8xxxu_read8(priv, REG_LEDCFG2);
+ val8 &= ~LEDCFG2_DPDT_SELECT;
+ rtl8xxxu_write8(priv, REG_LEDCFG2, val8);
/* 0x0005[1] = 1 turn off MAC by HW state machine*/
val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
@@ -5380,11 +4146,6 @@ static int rtl8723bu_active_to_emu(struct rtl8xxxu_priv *priv)
goto exit;
}
- /* Enable BT control XTAL setting */
- val8 = rtl8xxxu_read8(priv, REG_AFE_MISC);
- val8 &= ~AFE_MISC_WL_XTAL_CTRL;
- rtl8xxxu_write8(priv, REG_AFE_MISC, val8);
-
/* 0x0000[5] = 1 analog Ips to digital, 1:isolation */
val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
val8 |= SYS_ISO_ANALOG_IPS;
@@ -5399,7 +4160,7 @@ exit:
return ret;
}
-static int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv)
+int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv)
{
u8 val8;
u8 val32;
@@ -5455,7 +4216,7 @@ exit:
return ret;
}
-static void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv)
+void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv)
{
u8 val8;
@@ -5567,127 +4328,6 @@ exit:
return ret;
}
-static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- u32 val32;
- int count, ret = 0;
-
- /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */
- val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
- val8 |= LDOA15_ENABLE;
- rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
-
- /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/
- val8 = rtl8xxxu_read8(priv, 0x0067);
- val8 &= ~BIT(4);
- rtl8xxxu_write8(priv, 0x0067, val8);
-
- mdelay(1);
-
- /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */
- val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
- val8 &= ~SYS_ISO_ANALOG_IPS;
- rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
-
- /* Disable SW LPS 0x04[10]= 0 */
- val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO);
- val32 &= ~APS_FSMCO_SW_LPS;
- rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
-
- /* Wait until 0x04[17] = 1 power ready */
- for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- if (val32 & BIT(17))
- break;
-
- udelay(10);
- }
-
- if (!count) {
- ret = -EBUSY;
- goto exit;
- }
-
- /* We should be able to optimize the following three entries into one */
-
- /* Release WLON reset 0x04[16]= 1*/
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- val32 |= APS_FSMCO_WLON_RESET;
- rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
-
- /* Disable HWPDN 0x04[15]= 0*/
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- val32 &= ~APS_FSMCO_HW_POWERDOWN;
- rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
-
- /* Disable WL suspend*/
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE);
- rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
-
- /* Set, then poll until 0 */
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- val32 |= APS_FSMCO_MAC_ENABLE;
- rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
-
- for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
- val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
- if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) {
- ret = 0;
- break;
- }
- udelay(10);
- }
-
- if (!count) {
- ret = -EBUSY;
- goto exit;
- }
-
- /* Enable WL control XTAL setting */
- val8 = rtl8xxxu_read8(priv, REG_AFE_MISC);
- val8 |= AFE_MISC_WL_XTAL_CTRL;
- rtl8xxxu_write8(priv, REG_AFE_MISC, val8);
-
- /* Enable falling edge triggering interrupt */
- val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1);
- val8 |= BIT(1);
- rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8);
-
- /* Enable GPIO9 interrupt mode */
- val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1);
- val8 |= BIT(1);
- rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8);
-
- /* Enable GPIO9 input mode */
- val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2);
- val8 &= ~BIT(1);
- rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8);
-
- /* Enable HSISR GPIO[C:0] interrupt */
- val8 = rtl8xxxu_read8(priv, REG_HSIMR);
- val8 |= BIT(0);
- rtl8xxxu_write8(priv, REG_HSIMR, val8);
-
- /* Enable HSISR GPIO9 interrupt */
- val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2);
- val8 |= BIT(1);
- rtl8xxxu_write8(priv, REG_HSIMR + 2, val8);
-
- val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL);
- val8 |= MULTI_WIFI_HW_ROF_EN;
- rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8);
-
- /* For GPIO9 internal pull high setting BIT(14) */
- val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1);
- val8 |= BIT(6);
- rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8);
-
-exit:
- return ret;
-}
-
static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv)
{
u8 val8;
@@ -5713,7 +4353,7 @@ static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv)
return 0;
}
-static int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv)
+int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv)
{
struct device *dev = &priv->udev->dev;
u32 val32;
@@ -5836,62 +4476,6 @@ exit:
return ret;
}
-static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- u16 val16;
- u32 val32;
- int ret;
-
- rtl8723a_disabled_to_emu(priv);
-
- ret = rtl8723b_emu_to_active(priv);
- if (ret)
- goto exit;
-
- /*
- * Enable MAC DMA/WMAC/SCHEDULE/SEC block
- * Set CR bit10 to enable 32k calibration.
- */
- val16 = rtl8xxxu_read16(priv, REG_CR);
- val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE |
- CR_TXDMA_ENABLE | CR_RXDMA_ENABLE |
- CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE |
- CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE |
- CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE);
- rtl8xxxu_write16(priv, REG_CR, val16);
-
- /*
- * BT coexist power on settings. This is identical for 1 and 2
- * antenna parts.
- */
- rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20);
-
- val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
- val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN;
- rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
-
- rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18);
- rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04);
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
- /* Antenna inverse */
- rtl8xxxu_write8(priv, 0xfe08, 0x01);
-
- val16 = rtl8xxxu_read16(priv, REG_PWR_DATA);
- val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
- rtl8xxxu_write16(priv, REG_PWR_DATA, val16);
-
- val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
- val32 |= LEDCFG0_DPDT_SELECT;
- rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
-
- val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
- val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA;
- rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
-exit:
- return ret;
-}
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static int rtl8192cu_power_on(struct rtl8xxxu_priv *priv)
@@ -6051,48 +4635,6 @@ void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv)
rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0e);
}
-static void rtl8723bu_power_off(struct rtl8xxxu_priv *priv)
-{
- u8 val8;
- u16 val16;
-
- rtl8xxxu_flush_fifo(priv);
-
- /*
- * Disable TX report timer
- */
- val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL);
- val8 &= ~TX_REPORT_CTRL_TIMER_ENABLE;
- rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8);
-
- rtl8xxxu_write8(priv, REG_CR, 0x0000);
-
- rtl8xxxu_active_to_lps(priv);
-
- /* Reset Firmware if running in RAM */
- if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL)
- rtl8xxxu_firmware_self_reset(priv);
-
- /* Reset MCU */
- val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
- val16 &= ~SYS_FUNC_CPU_ENABLE;
- rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
-
- /* Reset MCU ready status */
- rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
-
- rtl8723bu_active_to_emu(priv);
-
- val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
- val8 |= BIT(3); /* APS_FSMCO_HW_SUSPEND */
- rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
-
- /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */
- val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2);
- val8 |= BIT(0);
- rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8);
-}
-
#ifdef NEED_PS_TDMA
static void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv,
u8 arg1, u8 arg2, u8 arg3, u8 arg4, u8 arg5)
@@ -6110,113 +4652,6 @@ static void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv,
}
#endif
-static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv)
-{
- struct h2c_cmd h2c;
- u32 val32;
- u8 val8;
-
- /*
- * No indication anywhere as to what 0x0790 does. The 2 antenna
- * vendor code preserves bits 6-7 here.
- */
- rtl8xxxu_write8(priv, 0x0790, 0x05);
- /*
- * 0x0778 seems to be related to enabling the number of antennas
- * In the vendor driver halbtc8723b2ant_InitHwConfig() sets it
- * to 0x03, while halbtc8723b1ant_InitHwConfig() sets it to 0x01
- */
- rtl8xxxu_write8(priv, 0x0778, 0x01);
-
- val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG);
- val8 |= BIT(5);
- rtl8xxxu_write8(priv, REG_GPIO_MUXCFG, val8);
-
- rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_IQADJ_G1, 0x780);
-
- rtl8723bu_write_btreg(priv, 0x3c, 0x15); /* BT TRx Mask on */
-
- /*
- * Set BT grant to low
- */
- memset(&h2c, 0, sizeof(struct h2c_cmd));
- h2c.bt_grant.cmd = H2C_8723B_BT_GRANT;
- h2c.bt_grant.data = 0;
- rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_grant));
-
- /*
- * WLAN action by PTA
- */
- rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04);
-
- /*
- * BT select S0/S1 controlled by WiFi
- */
- val8 = rtl8xxxu_read8(priv, 0x0067);
- val8 |= BIT(5);
- rtl8xxxu_write8(priv, 0x0067, val8);
-
- val32 = rtl8xxxu_read32(priv, REG_PWR_DATA);
- val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
- rtl8xxxu_write32(priv, REG_PWR_DATA, val32);
-
- /*
- * Bits 6/7 are marked in/out ... but for what?
- */
- rtl8xxxu_write8(priv, 0x0974, 0xff);
-
- val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER);
- val32 |= (BIT(0) | BIT(1));
- rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32);
-
- rtl8xxxu_write8(priv, REG_RFE_CTRL_ANTA_SRC, 0x77);
-
- val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
- val32 &= ~BIT(24);
- val32 |= BIT(23);
- rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
-
- /*
- * Fix external switch Main->S1, Aux->S0
- */
- val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
- val8 &= ~BIT(0);
- rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
-
- memset(&h2c, 0, sizeof(struct h2c_cmd));
- h2c.ant_sel_rsv.cmd = H2C_8723B_ANT_SEL_RSV;
- h2c.ant_sel_rsv.ant_inverse = 1;
- h2c.ant_sel_rsv.int_switch_type = 0;
- rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv));
-
- /*
- * 0x280, 0x00, 0x200, 0x80 - not clear
- */
- rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
-
- /*
- * Software control, antenna at WiFi side
- */
-#ifdef NEED_PS_TDMA
- rtl8723bu_set_ps_tdma(priv, 0x08, 0x00, 0x00, 0x00, 0x00);
-#endif
-
- rtl8xxxu_write32(priv, REG_BT_COEX_TABLE1, 0x55555555);
- rtl8xxxu_write32(priv, REG_BT_COEX_TABLE2, 0x55555555);
- rtl8xxxu_write32(priv, REG_BT_COEX_TABLE3, 0x00ffffff);
- rtl8xxxu_write8(priv, REG_BT_COEX_TABLE4, 0x03);
-
- memset(&h2c, 0, sizeof(struct h2c_cmd));
- h2c.bt_info.cmd = H2C_8723B_BT_INFO;
- h2c.bt_info.data = BIT(0);
- rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_info));
-
- memset(&h2c, 0, sizeof(struct h2c_cmd));
- h2c.ignore_wlan.cmd = H2C_8723B_BT_IGNORE_WLANACT;
- h2c.ignore_wlan.data = 0;
- rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ignore_wlan));
-}
-
void rtl8xxxu_gen2_disable_rf(struct rtl8xxxu_priv *priv)
{
u32 val32;
@@ -6226,48 +4661,6 @@ void rtl8xxxu_gen2_disable_rf(struct rtl8xxxu_priv *priv)
rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, val32);
}
-static void rtl8723bu_init_aggregation(struct rtl8xxxu_priv *priv)
-{
- u32 agg_rx;
- u8 agg_ctrl;
-
- /*
- * For now simply disable RX aggregation
- */
- agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL);
- agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN;
-
- agg_rx = rtl8xxxu_read32(priv, REG_RXDMA_AGG_PG_TH);
- agg_rx &= ~RXDMA_USB_AGG_ENABLE;
- agg_rx &= ~0xff0f;
-
- rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl);
- rtl8xxxu_write32(priv, REG_RXDMA_AGG_PG_TH, agg_rx);
-}
-
-static void rtl8723bu_init_statistics(struct rtl8xxxu_priv *priv)
-{
- u32 val32;
-
- /* Time duration for NHM unit: 4us, 0x2710=40ms */
- rtl8xxxu_write16(priv, REG_NHM_TIMER_8723B + 2, 0x2710);
- rtl8xxxu_write16(priv, REG_NHM_TH9_TH10_8723B + 2, 0xffff);
- rtl8xxxu_write32(priv, REG_NHM_TH3_TO_TH0_8723B, 0xffffff52);
- rtl8xxxu_write32(priv, REG_NHM_TH7_TO_TH4_8723B, 0xffffffff);
- /* TH8 */
- val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
- val32 |= 0xff;
- rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
- /* Enable CCK */
- val32 = rtl8xxxu_read32(priv, REG_NHM_TH9_TH10_8723B);
- val32 |= BIT(8) | BIT(9) | BIT(10);
- rtl8xxxu_write32(priv, REG_NHM_TH9_TH10_8723B, val32);
- /* Max power amongst all RX antennas */
- val32 = rtl8xxxu_read32(priv, REG_OFDM0_FA_RSTC);
- val32 |= BIT(7);
- rtl8xxxu_write32(priv, REG_OFDM0_FA_RSTC, val32);
-}
-
static void rtl8xxxu_old_init_queue_reserved_page(struct rtl8xxxu_priv *priv)
{
u8 val8;
@@ -8459,43 +6852,6 @@ static struct rtl8xxxu_fileops rtl8723au_fops = {
.mactable = rtl8xxxu_gen1_mac_init_table,
};
-static struct rtl8xxxu_fileops rtl8723bu_fops = {
- .parse_efuse = rtl8723bu_parse_efuse,
- .load_firmware = rtl8723bu_load_firmware,
- .power_on = rtl8723bu_power_on,
- .power_off = rtl8723bu_power_off,
- .reset_8051 = rtl8723bu_reset_8051,
- .llt_init = rtl8xxxu_auto_llt_table,
- .init_phy_bb = rtl8723bu_init_phy_bb,
- .init_phy_rf = rtl8723bu_init_phy_rf,
- .phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection,
- .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate,
- .config_channel = rtl8xxxu_gen2_config_channel,
- .parse_rx_desc = rtl8xxxu_parse_rxdesc24,
- .init_aggregation = rtl8723bu_init_aggregation,
- .init_statistics = rtl8723bu_init_statistics,
- .enable_rf = rtl8723b_enable_rf,
- .disable_rf = rtl8xxxu_gen2_disable_rf,
- .usb_quirks = rtl8xxxu_gen2_usb_quirks,
- .set_tx_power = rtl8723b_set_tx_power,
- .update_rate_mask = rtl8xxxu_gen2_update_rate_mask,
- .report_connect = rtl8xxxu_gen2_report_connect,
- .writeN_block_size = 1024,
- .mbox_ext_reg = REG_HMBOX_EXT0_8723B,
- .mbox_ext_width = 4,
- .tx_desc_size = sizeof(struct rtl8xxxu_txdesc40),
- .rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24),
- .has_s0s1 = 1,
- .adda_1t_init = 0x01c00014,
- .adda_1t_path_on = 0x01c00014,
- .adda_2t_path_on_a = 0x01c00014,
- .adda_2t_path_on_b = 0x01c00014,
- .trxff_boundary = 0x3f7f,
- .pbp_rx = PBP_PAGE_SIZE_256,
- .pbp_tx = PBP_PAGE_SIZE_256,
- .mactable = rtl8723b_mac_init_table,
-};
-
#ifdef CONFIG_RTL8XXXU_UNTESTED
static struct rtl8xxxu_fileops rtl8192cu_fops = {