diff mbox

ath10k: Support mgt frame per-chain rssi

Message ID 1517533386-30766-1-git-send-email-greearb@candelatech.com (mailing list archive)
State Rejected
Delegated to: Kalle Valo
Headers show

Commit Message

Ben Greear Feb. 2, 2018, 1:03 a.m. UTC 
From: Ben Greear <greearb@candelatech.com>

This provides per-chain rssh for management frames received
over wmi.

Signed-off-by: Ben Greear <greearb@candelatech.com>
---
 drivers/net/wireless/ath/ath10k/wmi.c | 21 ++++++++++++++++++++-
 drivers/net/wireless/ath/ath10k/wmi.h |  1 +
 2 files changed, 21 insertions(+), 1 deletion(-)

Comments

Arend van Spriel Feb. 2, 2018, 10:41 a.m. UTC | #1 
On 2/2/2018 2:03 AM, greearb@candelatech.com wrote:
> From: Ben Greear <greearb@candelatech.com>
>
> This provides per-chain rssh for management frames received

'rssh' should be 'rssi'.

Regards,
Arend

> over wmi.
>
> Signed-off-by: Ben Greear <greearb@candelatech.com>
> ---
>   drivers/net/wireless/ath/ath10k/wmi.c | 21 ++++++++++++++++++++-
>   drivers/net/wireless/ath/ath10k/wmi.h |  1 +
>   2 files changed, 21 insertions(+), 1 deletion(-)
diff mbox

Patch

diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 905af93..ff37274 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -2287,6 +2287,7 @@  static int ath10k_wmi_10_4_op_pull_mgmt_rx_ev(struct ath10k *ar,
 	u32 msdu_len;
 	struct wmi_mgmt_rx_ext_info *ext_info;
 	u32 len;
+	int i;
 
 	ev = (struct wmi_10_4_mgmt_rx_event *)skb->data;
 	ev_hdr = &ev->hdr;
@@ -2302,6 +2303,8 @@  static int ath10k_wmi_10_4_op_pull_mgmt_rx_ev(struct ath10k *ar,
 	arg->snr = ev_hdr->snr;
 	arg->phy_mode = ev_hdr->phy_mode;
 	arg->rate = ev_hdr->rate;
+	for (i = 0; i<4; i++)
+		arg->rssi_ctl[i] = ev_hdr->rssi_ctl[i];
 
 	msdu_len = __le32_to_cpu(arg->buf_len);
 	if (skb->len < msdu_len)
@@ -2357,6 +2360,13 @@  int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb)
 	u32 buf_len;
 	u16 fc;
 	int ret;
+	int i;
+
+	/* Initialize the rssi to 'ignore-me' value, stock wave-1
+	 * firmware doesn't support it.
+	 */
+	for (i = 0; i<4; i++)
+		arg.rssi_ctl[i] = 0x80;
 
 	ret = ath10k_wmi_pull_mgmt_rx(ar, skb, &arg);
 	if (ret) {
@@ -2416,6 +2426,12 @@  int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb)
 
 	status->freq = ieee80211_channel_to_frequency(channel, status->band);
 	status->signal = snr + ATH10K_DEFAULT_NOISE_FLOOR;
+	for (i = 0; i<4; i++) {
+		if (arg.rssi_ctl[i] != 0x80) {
+			status->chains |= BIT(i);
+			status->chain_signal[i] = ATH10K_DEFAULT_NOISE_FLOOR + arg.rssi_ctl[i];
+		}
+	}
 	status->rate_idx = ath10k_mac_bitrate_to_idx(sband, rate / 100);
 
 	hdr = (struct ieee80211_hdr *)skb->data;
@@ -2451,8 +2467,11 @@  int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb)
 		   fc & IEEE80211_FCTL_FTYPE, fc & IEEE80211_FCTL_STYPE);
 
 	ath10k_dbg(ar, ATH10K_DBG_MGMT,
-		   "event mgmt rx freq %d band %d snr %d, rate_idx %d\n",
+		   "event mgmt rx freq %d band %d snr %d chains: 0x%x(%d %d %d %d), rate_idx %d\n",
 		   status->freq, status->band, status->signal,
+		   status->chains,
+		   status->chain_signal[0], status->chain_signal[1],
+		   status->chain_signal[2], status->chain_signal[3],
 		   status->rate_idx);
 
 	ieee80211_rx(ar->hw, skb);
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index a3ba191..d198772 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -6490,6 +6490,7 @@  struct wmi_scan_ev_arg {
 struct wmi_mgmt_rx_ev_arg {
 	__le32 channel;
 	__le32 snr;
+	u8 rssi_ctl[4];
 	__le32 rate;
 	__le32 phy_mode;
 	__le32 buf_len;