@@ -294,7 +294,6 @@ struct ath_tx_control {
* (axq_qnum).
*/
struct ath_tx {
- u16 seq_no;
u32 txqsetup;
spinlock_t txbuflock;
struct list_head txbuf;
@@ -563,6 +562,7 @@ int ath_tx_init(struct ath_softc *sc, int nbufs);
int ath_txq_update(struct ath_softc *sc, int qnum,
struct ath9k_tx_queue_info *q);
void ath_update_max_aggr_framelen(struct ath_softc *sc, int queue, int txop);
+void ath_assign_seq(struct ath_common *common, struct sk_buff *skb);
int ath_tx_start(struct ieee80211_hw *hw, struct sk_buff *skb,
struct ath_tx_control *txctl);
void ath_tx_cabq(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
@@ -592,6 +592,8 @@ void ath9k_release_buffered_frames(struct ieee80211_hw *hw,
struct ath_vif {
struct list_head list;
+ u16 seq_no;
+
/* BSS info */
u8 bssid[ETH_ALEN];
u16 aid;
@@ -144,16 +144,8 @@ static struct ath_buf *ath9k_beacon_generate(struct ieee80211_hw *hw,
mgmt_hdr->u.beacon.timestamp = avp->tsf_adjust;
info = IEEE80211_SKB_CB(skb);
- if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
- /*
- * TODO: make sure the seq# gets assigned properly (vs. other
- * TX frames)
- */
- struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
- sc->tx.seq_no += 0x10;
- hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
- hdr->seq_ctrl |= cpu_to_le16(sc->tx.seq_no);
- }
+
+ ath_assign_seq(common, skb);
if (vif->p2p)
ath9k_beacon_add_noa(sc, avp, skb);
@@ -57,7 +57,7 @@ int ath9k_cmn_beacon_config_sta(struct ath_hw *ah,
struct ath9k_beacon_state *bs)
{
struct ath_common *common = ath9k_hw_common(ah);
- int dtim_intval, sleepduration;
+ int dtim_intval;
u64 tsf;
/* No need to configure beacon if we are not associated */
@@ -75,7 +75,6 @@ int ath9k_cmn_beacon_config_sta(struct ath_hw *ah,
* last beacon we received (which may be none).
*/
dtim_intval = conf->intval * conf->dtim_period;
- sleepduration = ah->hw->conf.listen_interval * conf->intval;
/*
* Pull nexttbtt forward to reflect the current
@@ -113,7 +112,7 @@ int ath9k_cmn_beacon_config_sta(struct ath_hw *ah,
*/
bs->bs_sleepduration = TU_TO_USEC(roundup(IEEE80211_MS_TO_TU(100),
- sleepduration));
+ conf->intval));
if (bs->bs_sleepduration > bs->bs_dtimperiod)
bs->bs_sleepduration = bs->bs_dtimperiod;
@@ -464,6 +464,7 @@ static int ath9k_init_priv(struct ath9k_htc_priv *priv,
return -ENOMEM;
ah->dev = priv->dev;
+ ah->hw = priv->hw;
ah->hw_version.devid = devid;
ah->hw_version.usbdev = drv_info;
ah->ah_flags |= AH_USE_EEPROM;
@@ -978,7 +978,7 @@ static bool ath9k_rx_prepare(struct ath9k_htc_priv *priv,
struct ath_hw *ah = common->ah;
struct ath_htc_rx_status *rxstatus;
struct ath_rx_status rx_stats;
- bool decrypt_error;
+ bool decrypt_error = false;
if (skb->len < HTC_RX_FRAME_HEADER_SIZE) {
ath_err(common, "Corrupted RX frame, dropping (len: %d)\n",
@@ -502,7 +502,7 @@ irqreturn_t ath_isr(int irq, void *dev)
* touch anything. Note this can happen early
* on if the IRQ is shared.
*/
- if (test_bit(ATH_OP_INVALID, &common->op_flags))
+ if (!ah || test_bit(ATH_OP_INVALID, &common->op_flags))
return IRQ_NONE;
/* shared irq, not for us */
@@ -2332,7 +2332,7 @@ static void ath9k_remove_chanctx(struct ieee80211_hw *hw,
conf->def.chan->center_freq);
ctx->assigned = false;
- ctx->hw_queue_base = -1;
+ ctx->hw_queue_base = 0;
ath_chanctx_event(sc, NULL, ATH_CHANCTX_EVENT_UNASSIGN);
mutex_unlock(&sc->mutex);
@@ -54,6 +54,12 @@ static struct sk_buff *ath9k_build_tx99_skb(struct ath_softc *sc)
struct ieee80211_hdr *hdr;
struct ieee80211_tx_info *tx_info;
struct sk_buff *skb;
+ struct ath_vif *avp;
+
+ if (!sc->tx99_vif)
+ return NULL;
+
+ avp = (struct ath_vif *)sc->tx99_vif->drv_priv;
skb = alloc_skb(len, GFP_KERNEL);
if (!skb)
@@ -71,7 +77,7 @@ static struct sk_buff *ath9k_build_tx99_skb(struct ath_softc *sc)
memcpy(hdr->addr2, hw->wiphy->perm_addr, ETH_ALEN);
memcpy(hdr->addr3, hw->wiphy->perm_addr, ETH_ALEN);
- hdr->seq_ctrl |= cpu_to_le16(sc->tx.seq_no);
+ hdr->seq_ctrl |= cpu_to_le16(avp->seq_no);
tx_info = IEEE80211_SKB_CB(skb);
memset(tx_info, 0, sizeof(*tx_info));
@@ -2139,6 +2139,28 @@ static struct ath_buf *ath_tx_setup_buffer(struct ath_softc *sc,
return bf;
}
+void ath_assign_seq(struct ath_common *common, struct sk_buff *skb)
+{
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_vif *vif = info->control.vif;
+ struct ath_vif *avp;
+
+ if (!(info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ))
+ return;
+
+ if (!vif)
+ return;
+
+ avp = (struct ath_vif *)vif->drv_priv;
+
+ if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
+ avp->seq_no += 0x10;
+
+ hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
+ hdr->seq_ctrl |= cpu_to_le16(avp->seq_no);
+}
+
static int ath_tx_prepare(struct ieee80211_hw *hw, struct sk_buff *skb,
struct ath_tx_control *txctl)
{
@@ -2162,17 +2184,7 @@ static int ath_tx_prepare(struct ieee80211_hw *hw, struct sk_buff *skb,
if (info->control.hw_key)
frmlen += info->control.hw_key->icv_len;
- /*
- * As a temporary workaround, assign seq# here; this will likely need
- * to be cleaned up to work better with Beacon transmission and virtual
- * BSSes.
- */
- if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
- if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
- sc->tx.seq_no += 0x10;
- hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
- hdr->seq_ctrl |= cpu_to_le16(sc->tx.seq_no);
- }
+ ath_assign_seq(ath9k_hw_common(sc->sc_ah), skb);
if ((vif && vif->type != NL80211_IFTYPE_AP &&
vif->type != NL80211_IFTYPE_AP_VLAN) ||
@@ -79,13 +79,13 @@ void ath_printk(const char *level, const struct ath_common* common,
vaf.fmt = fmt;
vaf.va = &args;
- if (common && common->hw && common->hw->wiphy)
+ if (common && common->hw && common->hw->wiphy) {
printk("%sath: %s: %pV",
level, wiphy_name(common->hw->wiphy), &vaf);
- else
+ trace_ath_log(common->hw->wiphy, &vaf);
+ } else {
printk("%sath: %pV", level, &vaf);
-
- trace_ath_log(common->hw->wiphy, &vaf);
+ }
va_end(args);
}
@@ -27,10 +27,17 @@ config BRCMFMAC
one of the bus interface support. If you choose to build a module,
it'll be called brcmfmac.ko.
+config BRCMFMAC_PROTO_BCDC
+ bool
+
+config BRCMFMAC_PROTO_MSGBUF
+ bool
+
config BRCMFMAC_SDIO
bool "SDIO bus interface support for FullMAC driver"
depends on (MMC = y || MMC = BRCMFMAC)
depends on BRCMFMAC
+ select BRCMFMAC_PROTO_BCDC
select FW_LOADER
default y
---help---
@@ -42,6 +49,7 @@ config BRCMFMAC_USB
bool "USB bus interface support for FullMAC driver"
depends on (USB = y || USB = BRCMFMAC)
depends on BRCMFMAC
+ select BRCMFMAC_PROTO_BCDC
select FW_LOADER
---help---
This option enables the USB bus interface support for Broadcom
@@ -52,6 +60,8 @@ config BRCMFMAC_PCIE
bool "PCIE bus interface support for FullMAC driver"
depends on BRCMFMAC
depends on PCI
+ depends on HAS_DMA
+ select BRCMFMAC_PROTO_MSGBUF
select FW_LOADER
---help---
This option enables the PCIE bus interface support for Broadcom
@@ -30,16 +30,18 @@ brcmfmac-objs += \
fwsignal.o \
p2p.o \
proto.o \
- bcdc.o \
- commonring.o \
- flowring.o \
- msgbuf.o \
dhd_common.o \
dhd_linux.o \
firmware.o \
feature.o \
btcoex.o \
vendor.o
+brcmfmac-$(CONFIG_BRCMFMAC_PROTO_BCDC) += \
+ bcdc.o
+brcmfmac-$(CONFIG_BRCMFMAC_PROTO_MSGBUF) += \
+ commonring.o \
+ flowring.o \
+ msgbuf.o
brcmfmac-$(CONFIG_BRCMFMAC_SDIO) += \
dhd_sdio.o \
bcmsdh.o
@@ -16,9 +16,12 @@
#ifndef BRCMFMAC_BCDC_H
#define BRCMFMAC_BCDC_H
-
+#ifdef CONFIG_BRCMFMAC_PROTO_BCDC
int brcmf_proto_bcdc_attach(struct brcmf_pub *drvr);
void brcmf_proto_bcdc_detach(struct brcmf_pub *drvr);
-
+#else
+static inline int brcmf_proto_bcdc_attach(struct brcmf_pub *drvr) { return 0; }
+static inline void brcmf_proto_bcdc_detach(struct brcmf_pub *drvr) {}
+#endif
#endif /* BRCMFMAC_BCDC_H */
@@ -185,7 +185,13 @@ static void brcmf_fweh_handle_if_event(struct brcmf_pub *drvr,
ifevent->action, ifevent->ifidx, ifevent->bssidx,
ifevent->flags, ifevent->role);
- if (ifevent->flags & BRCMF_E_IF_FLAG_NOIF) {
+ /* The P2P Device interface event must not be ignored
+ * contrary to what firmware tells us. The only way to
+ * distinguish the P2P Device is by looking at the ifidx
+ * and bssidx received.
+ */
+ if (!(ifevent->ifidx == 0 && ifevent->bssidx == 1) &&
+ (ifevent->flags & BRCMF_E_IF_FLAG_NOIF)) {
brcmf_dbg(EVENT, "event can be ignored\n");
return;
}
@@ -210,12 +216,12 @@ static void brcmf_fweh_handle_if_event(struct brcmf_pub *drvr,
return;
}
- if (ifevent->action == BRCMF_E_IF_CHANGE)
+ if (ifp && ifevent->action == BRCMF_E_IF_CHANGE)
brcmf_fws_reset_interface(ifp);
err = brcmf_fweh_call_event_handler(ifp, emsg->event_code, emsg, data);
- if (ifevent->action == BRCMF_E_IF_DEL) {
+ if (ifp && ifevent->action == BRCMF_E_IF_DEL) {
brcmf_fws_del_interface(ifp);
brcmf_del_if(drvr, ifevent->bssidx);
}
@@ -172,6 +172,8 @@ enum brcmf_fweh_event_code {
#define BRCMF_E_IF_ROLE_STA 0
#define BRCMF_E_IF_ROLE_AP 1
#define BRCMF_E_IF_ROLE_WDS 2
+#define BRCMF_E_IF_ROLE_P2P_GO 3
+#define BRCMF_E_IF_ROLE_P2P_CLIENT 4
/**
* definitions for event packet validation.
@@ -15,6 +15,7 @@
#ifndef BRCMFMAC_MSGBUF_H
#define BRCMFMAC_MSGBUF_H
+#ifdef CONFIG_BRCMFMAC_PROTO_MSGBUF
#define BRCMF_H2D_MSGRING_CONTROL_SUBMIT_MAX_ITEM 20
#define BRCMF_H2D_MSGRING_RXPOST_SUBMIT_MAX_ITEM 256
@@ -32,9 +33,15 @@
int brcmf_proto_msgbuf_rx_trigger(struct device *dev);
+void brcmf_msgbuf_delete_flowring(struct brcmf_pub *drvr, u8 flowid);
int brcmf_proto_msgbuf_attach(struct brcmf_pub *drvr);
void brcmf_proto_msgbuf_detach(struct brcmf_pub *drvr);
-void brcmf_msgbuf_delete_flowring(struct brcmf_pub *drvr, u8 flowid);
-
+#else
+static inline int brcmf_proto_msgbuf_attach(struct brcmf_pub *drvr)
+{
+ return 0;
+}
+static inline void brcmf_proto_msgbuf_detach(struct brcmf_pub *drvr) {}
+#endif
#endif /* BRCMFMAC_MSGBUF_H */
@@ -498,8 +498,11 @@ brcmf_configure_arp_offload(struct brcmf_if *ifp, bool enable)
static void
brcmf_cfg80211_update_proto_addr_mode(struct wireless_dev *wdev)
{
- struct net_device *ndev = wdev->netdev;
- struct brcmf_if *ifp = netdev_priv(ndev);
+ struct brcmf_cfg80211_vif *vif;
+ struct brcmf_if *ifp;
+
+ vif = container_of(wdev, struct brcmf_cfg80211_vif, wdev);
+ ifp = vif->ifp;
if ((wdev->iftype == NL80211_IFTYPE_ADHOC) ||
(wdev->iftype == NL80211_IFTYPE_AP) ||
@@ -4964,7 +4967,7 @@ static void brcmf_count_20mhz_channels(struct brcmf_cfg80211_info *cfg,
struct brcmu_chan ch;
int i;
- for (i = 0; i <= total; i++) {
+ for (i = 0; i < total; i++) {
ch.chspec = (u16)le32_to_cpu(chlist->element[i]);
cfg->d11inf.decchspec(&ch);
@@ -5189,6 +5192,7 @@ static int brcmf_enable_bw40_2g(struct brcmf_cfg80211_info *cfg)
ch.band = BRCMU_CHAN_BAND_2G;
ch.bw = BRCMU_CHAN_BW_40;
+ ch.sb = BRCMU_CHAN_SB_NONE;
ch.chnum = 0;
cfg->d11inf.encchspec(&ch);
@@ -5222,6 +5226,7 @@ static int brcmf_enable_bw40_2g(struct brcmf_cfg80211_info *cfg)
brcmf_update_bw40_channel_flag(&band->channels[j], &ch);
}
+ kfree(pbuf);
}
return err;
}
@@ -742,35 +742,49 @@ static void rtl8180_int_disable(struct ieee80211_hw *dev)
}
static void rtl8180_conf_basic_rates(struct ieee80211_hw *dev,
- u32 rates_mask)
+ u32 basic_mask)
{
struct rtl8180_priv *priv = dev->priv;
-
- u8 max, min;
u16 reg;
-
- max = fls(rates_mask) - 1;
- min = ffs(rates_mask) - 1;
+ u32 resp_mask;
+ u8 basic_max;
+ u8 resp_max, resp_min;
+
+ resp_mask = basic_mask;
+ /* IEEE80211 says the response rate should be equal to the highest basic
+ * rate that is not faster than received frame. But it says also that if
+ * the basic rate set does not contains any rate for the current
+ * modulation class then mandatory rate set must be used for that
+ * modulation class. Eventually add OFDM mandatory rates..
+ */
+ if ((resp_mask & 0xf) == resp_mask)
+ resp_mask |= 0x150; /* 6, 12, 24Mbps */
switch (priv->chip_family) {
case RTL818X_CHIP_FAMILY_RTL8180:
/* in 8180 this is NOT a BITMAP */
+ basic_max = fls(basic_mask) - 1;
reg = rtl818x_ioread16(priv, &priv->map->BRSR);
reg &= ~3;
- reg |= max;
+ reg |= basic_max;
rtl818x_iowrite16(priv, &priv->map->BRSR, reg);
break;
case RTL818X_CHIP_FAMILY_RTL8185:
+ resp_max = fls(resp_mask) - 1;
+ resp_min = ffs(resp_mask) - 1;
/* in 8185 this is a BITMAP */
- rtl818x_iowrite16(priv, &priv->map->BRSR, rates_mask);
- rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (max << 4) | min);
+ rtl818x_iowrite16(priv, &priv->map->BRSR, basic_mask);
+ rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (resp_max << 4) |
+ resp_min);
break;
case RTL818X_CHIP_FAMILY_RTL8187SE:
- /* in 8187se this is a BITMAP */
- rtl818x_iowrite16(priv, &priv->map->BRSR_8187SE, rates_mask);
+ /* in 8187se this is a BITMAP. BRSR reg actually sets
+ * response rates.
+ */
+ rtl818x_iowrite16(priv, &priv->map->BRSR_8187SE, resp_mask);
break;
}
}
@@ -1370,7 +1370,7 @@ struct rtl_mac {
bool rdg_en;
/*AP*/
- u8 bssid[6];
+ u8 bssid[ETH_ALEN] __aligned(2);
u32 vendor;
u8 mcs[16]; /* 16 bytes mcs for HT rates. */
u32 basic_rates; /* b/g rates */
@@ -501,9 +501,13 @@ static void microread_target_discovered(struct nfc_hci_dev *hdev, u8 gate,
targets->sens_res =
be16_to_cpu(*(u16 *)&skb->data[MICROREAD_EMCF_A_ATQA]);
targets->sel_res = skb->data[MICROREAD_EMCF_A_SAK];
- memcpy(targets->nfcid1, &skb->data[MICROREAD_EMCF_A_UID],
- skb->data[MICROREAD_EMCF_A_LEN]);
targets->nfcid1_len = skb->data[MICROREAD_EMCF_A_LEN];
+ if (targets->nfcid1_len > sizeof(targets->nfcid1)) {
+ r = -EINVAL;
+ goto exit_free;
+ }
+ memcpy(targets->nfcid1, &skb->data[MICROREAD_EMCF_A_UID],
+ targets->nfcid1_len);
break;
case MICROREAD_GATE_ID_MREAD_ISO_A_3:
targets->supported_protocols =
@@ -511,9 +515,13 @@ static void microread_target_discovered(struct nfc_hci_dev *hdev, u8 gate,
targets->sens_res =
be16_to_cpu(*(u16 *)&skb->data[MICROREAD_EMCF_A3_ATQA]);
targets->sel_res = skb->data[MICROREAD_EMCF_A3_SAK];
- memcpy(targets->nfcid1, &skb->data[MICROREAD_EMCF_A3_UID],
- skb->data[MICROREAD_EMCF_A3_LEN]);
targets->nfcid1_len = skb->data[MICROREAD_EMCF_A3_LEN];
+ if (targets->nfcid1_len > sizeof(targets->nfcid1)) {
+ r = -EINVAL;
+ goto exit_free;
+ }
+ memcpy(targets->nfcid1, &skb->data[MICROREAD_EMCF_A3_UID],
+ targets->nfcid1_len);
break;
case MICROREAD_GATE_ID_MREAD_ISO_B:
targets->supported_protocols = NFC_PROTO_ISO14443_B_MASK;
@@ -2,7 +2,8 @@
# Makefile for ST21NFCA HCI based NFC driver
#
-st21nfca_i2c-objs = i2c.o
+st21nfca_hci-objs = st21nfca.o st21nfca_dep.o
+obj-$(CONFIG_NFC_ST21NFCA) += st21nfca_hci.o
-obj-$(CONFIG_NFC_ST21NFCA) += st21nfca.o st21nfca_dep.o
+st21nfca_i2c-objs = i2c.o
obj-$(CONFIG_NFC_ST21NFCA_I2C) += st21nfca_i2c.o
@@ -2,7 +2,8 @@
# Makefile for ST21NFCB NCI based NFC driver
#
-st21nfcb_i2c-objs = i2c.o
+st21nfcb_nci-objs = ndlc.o st21nfcb.o
+obj-$(CONFIG_NFC_ST21NFCB) += st21nfcb_nci.o
-obj-$(CONFIG_NFC_ST21NFCB) += st21nfcb.o ndlc.o
+st21nfcb_i2c-objs = i2c.o
obj-$(CONFIG_NFC_ST21NFCB_I2C) += st21nfcb_i2c.o
@@ -1823,7 +1823,7 @@ void sta_set_sinfo(struct sta_info *sta, struct station_info *sinfo)
sinfo->bss_param.flags |= BSS_PARAM_FLAGS_SHORT_PREAMBLE;
if (sdata->vif.bss_conf.use_short_slot)
sinfo->bss_param.flags |= BSS_PARAM_FLAGS_SHORT_SLOT_TIME;
- sinfo->bss_param.dtim_period = sdata->local->hw.conf.ps_dtim_period;
+ sinfo->bss_param.dtim_period = sdata->vif.bss_conf.dtim_period;
sinfo->bss_param.beacon_interval = sdata->vif.bss_conf.beacon_int;
sinfo->sta_flags.set = 0;
@@ -329,7 +329,7 @@ static atomic_t rfkill_input_disabled = ATOMIC_INIT(0);
/**
* __rfkill_switch_all - Toggle state of all switches of given type
* @type: type of interfaces to be affected
- * @state: the new state
+ * @blocked: the new state
*
* This function sets the state of all switches of given type,
* unless a specific switch is claimed by userspace (in which case,
@@ -353,7 +353,7 @@ static void __rfkill_switch_all(const enum rfkill_type type, bool blocked)
/**
* rfkill_switch_all - Toggle state of all switches of given type
* @type: type of interfaces to be affected
- * @state: the new state
+ * @blocked: the new state
*
* Acquires rfkill_global_mutex and calls __rfkill_switch_all(@type, @state).
* Please refer to __rfkill_switch_all() for details.
@@ -54,7 +54,7 @@ static int rfkill_gpio_set_power(void *data, bool blocked)
if (blocked && !IS_ERR(rfkill->clk) && rfkill->clk_enabled)
clk_disable(rfkill->clk);
- rfkill->clk_enabled = blocked;
+ rfkill->clk_enabled = !blocked;
return 0;
}
@@ -163,6 +163,7 @@ static const struct acpi_device_id rfkill_acpi_match[] = {
{ "LNV4752", RFKILL_TYPE_GPS },
{ },
};
+MODULE_DEVICE_TABLE(acpi, rfkill_acpi_match);
#endif
static struct platform_driver rfkill_gpio_driver = {
@@ -7028,6 +7028,9 @@ void __cfg80211_send_event_skb(struct sk_buff *skb, gfp_t gfp)
struct nlattr *data = ((void **)skb->cb)[2];
enum nl80211_multicast_groups mcgrp = NL80211_MCGRP_TESTMODE;
+ /* clear CB data for netlink core to own from now on */
+ memset(skb->cb, 0, sizeof(skb->cb));
+
nla_nest_end(skb, data);
genlmsg_end(skb, hdr);
@@ -9357,6 +9360,9 @@ int cfg80211_vendor_cmd_reply(struct sk_buff *skb)
void *hdr = ((void **)skb->cb)[1];
struct nlattr *data = ((void **)skb->cb)[2];
+ /* clear CB data for netlink core to own from now on */
+ memset(skb->cb, 0, sizeof(skb->cb));
+
if (WARN_ON(!rdev->cur_cmd_info)) {
kfree_skb(skb);
return -EINVAL;
Dave, Please pull this batch of fixes intended for the 3.18 stream! Andrea Merello makes rtl818x_pci use a more reasonable transmission rate for HW generated frames. Fabian Frederick tweaks some kernel-doc bits to avoid warnings. Larry Finger corrects a possible unaligned access in the rtlwifi code. Marek Puzyniak avoids a kernel panic in ath9k_hw_reset. Sujith Manoharan goes for the hat trick -- he fixes a smatch warning in the shared ath code, he fixes a crash in ath9k, and he corrects a sequence number assignment problem in ath9k too. For ease of merging, I pulled the last bits of the wireless tree as well... Please let me know if there are problems! Thanks, John --- The following changes since commit 3f08e47291879fb047d7d4464d2beaedfea4eb63: rtlwifi: Fix static checker warnings for various drivers (2014-10-02 14:26:32 -0400) are available in the git repository at: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git tags/master-2014-10-08 for you to fetch changes up to 1fca350b761631d182c2e8bce530896e66404bc2: rtlwifi: Fix possible unaligned array in ether_addr_copy() (2014-10-08 15:24:16 -0400) ---------------------------------------------------------------- Andrea Merello (1): rtl818x_pci: fix response rate may be incorrect. Fabian Frederick (1): net: rfkill: kernel-doc warning fixes John W. Linville (1): Merge branch 'master' of git://git.kernel.org/.../linville/wireless Larry Finger (1): rtlwifi: Fix possible unaligned array in ether_addr_copy() Marek Puzyniak (1): ath9k_htc: avoid kernel panic in ath9k_hw_reset Sujith Manoharan (3): ath: Fix smatch warning ath9k: Fix crash in MCC mode ath9k: Fix sequence number assignment drivers/net/wireless/ath/ath9k/ath9k.h | 4 ++- drivers/net/wireless/ath/ath9k/beacon.c | 12 ++------ drivers/net/wireless/ath/ath9k/common-beacon.c | 5 ++- drivers/net/wireless/ath/ath9k/htc_drv_init.c | 1 + drivers/net/wireless/ath/ath9k/htc_drv_txrx.c | 2 +- drivers/net/wireless/ath/ath9k/main.c | 4 +-- drivers/net/wireless/ath/ath9k/tx99.c | 8 ++++- drivers/net/wireless/ath/ath9k/xmit.c | 34 +++++++++++++------- drivers/net/wireless/ath/main.c | 8 ++--- drivers/net/wireless/brcm80211/Kconfig | 10 ++++++ drivers/net/wireless/brcm80211/brcmfmac/Makefile | 10 +++--- drivers/net/wireless/brcm80211/brcmfmac/bcdc.h | 7 +++-- drivers/net/wireless/brcm80211/brcmfmac/fweh.c | 12 ++++++-- drivers/net/wireless/brcm80211/brcmfmac/fweh.h | 2 ++ drivers/net/wireless/brcm80211/brcmfmac/msgbuf.h | 11 +++++-- .../net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 11 +++++-- drivers/net/wireless/rtl818x/rtl8180/dev.c | 36 +++++++++++++++------- drivers/net/wireless/rtlwifi/wifi.h | 2 +- drivers/nfc/microread/microread.c | 16 +++++++--- drivers/nfc/st21nfca/Makefile | 5 +-- drivers/nfc/st21nfcb/Makefile | 5 +-- net/mac80211/sta_info.c | 2 +- net/rfkill/core.c | 4 +-- net/rfkill/rfkill-gpio.c | 3 +- net/wireless/nl80211.c | 6 ++++ 25 files changed, 149 insertions(+), 71 deletions(-)