@@ -37,12 +37,20 @@ Optional properties:
- clocks: List of clock specifiers, must contain an entry for each required
entry in clock-names.
- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
- "wifi_wcss_rtc".
-- interrupts: List of interrupt lines. Must contain an entry
- for each entry in the interrupt-names property.
+ "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and
+ "cxo_ref_clk_pin", "smmu_aggre2_noc_clk" for "qcom,wcn3990-wifi"
+ compatible target.
+- interrupts: reference to the list of 17 interrupt no's for "qcom,ipq4019-wifi"
+ compatible target.
+ reference to the list of 12 interrupt no's for "qcom,wcn3990-wifi"
+ compatible target.
+ Must contain interrupt-names property per entry for
+ "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets.
+
- interrupt-names: Must include the entries for MSI interrupt
names ("msi0" to "msi15") and legacy interrupt
- name ("legacy"),
+ name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi"
+ compatible targets.
- qcom,msi_addr: MSI interrupt address.
- qcom,msi_base: Base value to add before writing MSI data into
MSI address register.
@@ -55,7 +63,8 @@ Optional properties:
- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
the length can vary between hw versions.
- <supply-name>-supply: handle to the regulator device tree node
- optional "supply-name" is "vdd-0.8-cx-mx".
+ optional "supply-name" are "vdd-0.8-cx-mx",
+ "vdd-1.8-xo", "vdd-1.3-rfa" and "vdd-3.3-ch0".
Example (to supply the calibration data alone):
@@ -133,8 +142,10 @@ wifi@18000000 {
compatible = "qcom,wcn3990-wifi";
reg = <0x18800000 0x800000>;
reg-names = "membase";
- clocks = <&clock_gcc clk_aggre2_noc_clk>;
- clock-names = "smmu_aggre2_noc_clk"
+ clocks = <&clock_gcc clk_aggre2_noc_clk>,
+ <&clock_gcc clk_rf_clk2_pin>;
+ clock-names = "smmu_aggre2_noc_clk",
+ "cxo_ref_clk_pin";
interrupts =
<0 130 0 /* CE0 */ >,
<0 131 0 /* CE1 */ >,
@@ -149,4 +160,7 @@ wifi@18000000 {
<0 140 0 /* CE10 */ >,
<0 141 0 /* CE11 */ >;
vdd-0.8-cx-mx-supply = <&pm8998_l5>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
};
Add missing optional properties in WCN3990 wifi node. Signed-off-by: Govind Singh <govinds@codeaurora.org> --- .../bindings/net/wireless/qcom,ath10k.txt | 28 ++++++++++++++----- 1 file changed, 21 insertions(+), 7 deletions(-)