@@ -1706,7 +1706,7 @@ enum nl80211_commands {
* the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID
* is included in the probe request, but the match attributes
* will never let it go through), -EINVAL may be returned.
- * If ommited, no filtering is done.
+ * If omitted, no filtering is done.
*
* @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
* interface combinations. In each nested item, it contains attributes
@@ -1811,7 +1811,7 @@ enum nl80211_commands {
*
* @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
* used by the drivers which has MLME in firmware and does not have support
- * to report per station tx/rx activity to free up the staion entry from
+ * to report per station tx/rx activity to free up the station entry from
* the list. This needs to be used when the driver advertises the
* capability to timeout the stations.
*
@@ -2172,7 +2172,7 @@ enum nl80211_commands {
*
* @NL80211_ATTR_SCHED_SCAN_RSSI_ADJUST: When present the RSSI level for BSSs in
* the specified band is to be adjusted before doing
- * %NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI based comparision to figure out
+ * %NL80211_ATTR_SCHED_SCAN_RELATIVE_RSSI based comparison to figure out
* better BSSs. The attribute value is a packed structure
* value as specified by &struct nl80211_bss_select_rssi_adjust.
*
@@ -4859,7 +4859,7 @@ enum nl80211_iface_limit_attrs {
* numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
* => allows a STA plus three P2P interfaces
*
- * The list of these four possiblities could completely be contained
+ * The list of these four possibilities could completely be contained
* within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
* that any of these groups must match.
*
@@ -4889,7 +4889,7 @@ enum nl80211_if_combination_attrs {
* enum nl80211_plink_state - state of a mesh peer link finite state machine
*
* @NL80211_PLINK_LISTEN: initial state, considered the implicit
- * state of non existant mesh peer links
+ * state of non existent mesh peer links
* @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
* this mesh peer
* @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
@@ -5381,7 +5381,7 @@ enum nl80211_timeout_reason {
* request parameters IE in the probe request
* @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at
- * rate of at least 5.5M. In case non OCE AP is dicovered in the channel,
+ * rate of at least 5.5M. In case non OCE AP is discovered in the channel,
* only the first probe req in the channel will be sent in high rate.
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request
* tx deferral (dot11FILSProbeDelay shall be set to 15ms)
Spelling errors found by codespell Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> --- include/uapi/linux/nl80211.h | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)