@@ -1583,13 +1583,21 @@ static bool qca_prevent_wake(struct hci_dev *hdev)
return !wakeup;
}
-static int qca_regulator_init(struct hci_uart *hu)
+static int qca_power_on(struct hci_dev *hdev)
{
+ struct hci_uart *hu = hci_get_drvdata(hdev);
enum qca_btsoc_type soc_type = qca_soc_type(hu);
struct qca_serdev *qcadev;
+ struct qca_data *qca = hu->priv;
int ret;
bool sw_ctrl_state;
+ /* Non-serdev device usually is powered by external power
+ * and don't need additional action in driver for power on
+ */
+ if (!hu->serdev)
+ return 0;
+
/* Check for vregs status, may be hci down has turned
* off the voltage regulator.
*/
@@ -1607,27 +1615,29 @@ static int qca_regulator_init(struct hci_uart *hu)
}
}
- if (qca_is_wcn399x(soc_type)) {
- /* Forcefully enable wcn399x to enter in to boot mode. */
- host_set_baudrate(hu, 2400);
- ret = qca_send_power_pulse(hu, false);
- if (ret)
- return ret;
- }
-
/* For wcn6750 need to enable gpio bt_en */
if (qcadev->bt_en) {
gpiod_set_value_cansleep(qcadev->bt_en, 0);
msleep(50);
gpiod_set_value_cansleep(qcadev->bt_en, 1);
- msleep(50);
+ msleep(150);
if (qcadev->sw_ctrl) {
sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
}
}
- qca_set_speed(hu, QCA_INIT_SPEED);
+ if (qca_is_wcn399x(soc_type)) {
+ /* Forcefully enable wcn399x to enter in to boot mode. */
+ host_set_baudrate(hu, 2400);
+ ret = qca_send_power_pulse(hu, false);
+ if (ret)
+ return ret;
+ }
+
+ if (qca_is_wcn399x(soc_type) ||
+ qca_is_wcn6750(soc_type))
+ qca_set_speed(hu, QCA_INIT_SPEED);
if (qca_is_wcn399x(soc_type)) {
ret = qca_send_power_pulse(hu, true);
@@ -1647,38 +1657,12 @@ static int qca_regulator_init(struct hci_uart *hu)
return ret;
}
- hci_uart_set_flow_control(hu, false);
-
- return 0;
-}
-
-static int qca_power_on(struct hci_dev *hdev)
-{
- struct hci_uart *hu = hci_get_drvdata(hdev);
- enum qca_btsoc_type soc_type = qca_soc_type(hu);
- struct qca_serdev *qcadev;
- struct qca_data *qca = hu->priv;
- int ret = 0;
-
- /* Non-serdev device usually is powered by external power
- * and don't need additional action in driver for power on
- */
- if (!hu->serdev)
- return 0;
-
if (qca_is_wcn399x(soc_type) ||
- qca_is_wcn6750(soc_type)) {
- ret = qca_regulator_init(hu);
- } else {
- qcadev = serdev_device_get_drvdata(hu->serdev);
- if (qcadev->bt_en) {
- gpiod_set_value_cansleep(qcadev->bt_en, 1);
- /* Controller needs time to bootup. */
- msleep(150);
- }
- }
+ qca_is_wcn6750(soc_type))
+ hci_uart_set_flow_control(hu, false);
clear_bit(QCA_BT_OFF, &qca->flags);
+
return ret;
}
With wcn6750 support added, regulator-based code was extended with the bt_en gpio support. Now there is no need to keep regulator and non-regulator code paths separate. Merge both code paths. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- drivers/bluetooth/hci_qca.c | 64 ++++++++++++++----------------------- 1 file changed, 24 insertions(+), 40 deletions(-)