| Message ID | 20211226153624.162281-13-marcan@marcan.st (mailing list archive) |
|---|---|
| State | Superseded |
| Delegated to: | Kalle Valo |
| Headers | show |
| Series | brcmfmac: Support Apple T2 and M1 platforms | expand |
On Sun, Dec 26, 2021 at 4:38 PM Hector Martin <marcan@marcan.st> wrote: > The driver was enabling IRQs before the message processing was > initialized. This could cause IRQs to come in too early and crash the > driver. Instead, move the IRQ enable and hostready to a bus preinit > function, at which point everything is properly initialized. > > Fixes: 9e37f045d5e7 ("brcmfmac: Adding PCIe bus layer support.") > Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Yours, Linus Walleij
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c index d31f5a668cec..ffb01872c6a3 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c @@ -1378,6 +1378,18 @@ static void brcmf_pcie_down(struct device *dev) { } +static int brcmf_pcie_preinit(struct device *dev) +{ + struct brcmf_bus *bus_if = dev_get_drvdata(dev); + struct brcmf_pciedev *buspub = bus_if->bus_priv.pcie; + + brcmf_dbg(PCIE, "Enter\n"); + + brcmf_pcie_intr_enable(buspub->devinfo); + brcmf_pcie_hostready(buspub->devinfo); + + return 0; +} static int brcmf_pcie_tx(struct device *dev, struct sk_buff *skb) { @@ -1488,6 +1500,7 @@ static int brcmf_pcie_reset(struct device *dev) } static const struct brcmf_bus_ops brcmf_pcie_bus_ops = { + .preinit = brcmf_pcie_preinit, .txdata = brcmf_pcie_tx, .stop = brcmf_pcie_down, .txctl = brcmf_pcie_tx_ctlpkt, @@ -2053,9 +2066,6 @@ static void brcmf_pcie_setup(struct device *dev, int ret, init_waitqueue_head(&devinfo->mbdata_resp_wait); - brcmf_pcie_intr_enable(devinfo); - brcmf_pcie_hostready(devinfo); - ret = brcmf_attach(&devinfo->pdev->dev); if (ret) goto fail;
The driver was enabling IRQs before the message processing was initialized. This could cause IRQs to come in too early and crash the driver. Instead, move the IRQ enable and hostready to a bus preinit function, at which point everything is properly initialized. Fixes: 9e37f045d5e7 ("brcmfmac: Adding PCIe bus layer support.") Signed-off-by: Hector Martin <marcan@marcan.st> --- .../wireless/broadcom/brcm80211/brcmfmac/pcie.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-)