similarity index 71%
rename from drivers/staging/wfx/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
rename to Documentation/devicetree/bindings/staging/net/wireless/silabs,wfx.yaml
@@ -3,7 +3,7 @@
%YAML 1.2
---
-$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml#
+$id: http://devicetree.org/schemas/staging/net/wireless/silabs,wfx.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Silicon Labs WFxxx devicetree bindings
@@ -11,32 +11,30 @@ title: Silicon Labs WFxxx devicetree bindings
maintainers:
- Jérôme Pouiller <jerome.pouiller@silabs.com>
-description:
- The WFxxx chip series can be connected via SPI or via SDIO.
+description: >
+ Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device
+ from the WFxxx series is the WF200 described here:
+ https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
- For SDIO':'
+ The WF200 can be connected via SPI or via SDIO.
- The driver is able to detect a WFxxx chip on SDIO bus by matching its Vendor
- ID and Product ID. However, driver will only provide limited features in
- this case. Thus declaring WFxxx chip in device tree is recommended (and may
- become mandatory in the future).
+ For SDIO:
- In addition, it is recommended to declare a mmc-pwrseq on SDIO host above
- WFx. Without it, you may encounter issues with warm boot. The mmc-pwrseq
- should be compatible with mmc-pwrseq-simple. Please consult
+ Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is
+ sufficient for the SDIO devices).
+
+ It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
+ it, you may encounter issues during reboot. The mmc-pwrseq should be
+ compatible with mmc-pwrseq-simple. Please consult
Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more
information.
- For SPI':'
+ For SPI:
In add of the properties below, please consult
Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI
related properties.
- Note that in add of the properties below, the WFx driver also supports
- `mac-address` and `local-mac-address` as described in
- Documentation/devicetree/bindings/net/ethernet.txt
-
properties:
compatible:
items:
@@ -45,22 +43,23 @@ properties:
- silabs,brd8022a # WF200 Evaluation Board
- silabs,brd8023a # WFM200 Evaluation Board
- const: silabs,wf200 # Chip alone without antenna
+
reg:
description:
When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
the chip select address of the device as defined in the SPI devices
bindings.
maxItems: 1
- spi-max-frequency:
- description: (SPI only) Maximum SPI clocking speed of device in Hz.
- maxItems: 1
+
+ spi-max-frequency: true
+
interrupts:
- description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and
- IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When
- SPI is used, this property is required. When SDIO is used, the "in-band"
+ description: The interrupt line. Should be IRQ_TYPE_EDGE_RISING. When SPI is
+ used, this property is required. When SDIO is used, the "in-band"
interrupt provided by the SDIO bus is used unless an interrupt is defined
in the Device Tree.
maxItems: 1
+
reset-gpios:
description: (SPI only) Phandle of gpio that will be used to reset chip
during probe. Without this property, you may encounter issues with warm
@@ -68,16 +67,24 @@ properties:
For SDIO, the reset gpio should declared using a mmc-pwrseq.
maxItems: 1
+
wakeup-gpios:
description: Phandle of gpio that will be used to wake-up chip. Without this
property, driver will disable most of power saving features.
maxItems: 1
+
silabs,antenna-config-file:
$ref: /schemas/types.yaml#/definitions/string
description: Use an alternative file for antenna configuration (aka
"Platform Data Set" in Silabs jargon). Default depends of "compatible"
string. For "silabs,wf200", the default is 'wf200.pds'.
+ local-mac-address: true
+
+ mac-address: true
+
+additionalProperties: false
+
required:
- compatible
- reg
@@ -87,11 +94,11 @@ examples:
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
- spi0 {
+ spi {
#address-cells = <1>;
#size-cells = <0>;
- wfx@0 {
+ wifi@0 {
compatible = "silabs,brd8022a", "silabs,wf200";
pinctrl-names = "default";
pinctrl-0 = <&wfx_irq &wfx_gpios>;
@@ -114,12 +121,12 @@ examples:
reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
- mmc0 {
+ mmc {
mmc-pwrseq = <&wfx_pwrseq>;
#address-cells = <1>;
#size-cells = <0>;
- mmc@1 {
+ wifi@1 {
compatible = "silabs,brd8022a", "silabs,wf200";
pinctrl-names = "default";
pinctrl-0 = <&wfx_wakeup>;
@@ -17652,6 +17652,7 @@ F: drivers/platform/x86/touchscreen_dmi.c
SILICON LABS WIRELESS DRIVERS (for WFxxx series)
M: Jérôme Pouiller <jerome.pouiller@silabs.com>
S: Supported
+F: Documentation/devicetree/bindings/staging/net/wireless/silabs,wfx.yaml
F: drivers/staging/wfx/
SILICON MOTION SM712 FRAME BUFFER DRIVER