| Message ID | 20230206040739.1290-1-quic_wgong@quicinc.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Delegated to: | Kalle Valo |
| Headers | show |
| Series | [v4] wifi: ath11k: change to set 11d state instead of start 11d scan while disconnect | expand |
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c index 4218211afa30..b0c3cf258d12 100644 --- a/drivers/net/wireless/ath/ath11k/mac.c +++ b/drivers/net/wireless/ath/ath11k/mac.c @@ -7190,8 +7190,12 @@ ath11k_mac_op_unassign_vif_chanctx(struct ieee80211_hw *hw, ret); } - if (arvif->vdev_type == WMI_VDEV_TYPE_STA) - ath11k_mac_11d_scan_start(ar, arvif->vdev_id); + if (arvif->vdev_type == WMI_VDEV_TYPE_STA && + ar->state_11d != ATH11K_11D_PREPARING && + test_bit(WMI_TLV_SERVICE_11D_OFFLOAD, ab->wmi_ab.svc_map)) { + reinit_completion(&ar->completed_11d_scan); + ar->state_11d = ATH11K_11D_PREPARING; + } mutex_unlock(&ar->conf_mutex); }
When switch to connect to a new AP for station which is already connected to an AP, the time cost is too long, it arrives 10 seconds. The reason is when switch connection, disconnect operation happened on the 1st AP, then 11d scan start command sent to firmware, and then a new hw scan arrived for the 2nd AP. The 11d scan is running at this moment, so the hw scan can not start immediately, it needs to wait the 11d scan finished, it increased the time cost of switch AP and even happened scan fail as log below after apply the incoming patch. [ 1194.815104] ath11k_pci 0000:06:00.0: failed to start hw scan: -110 [ 1196.864157] ath11k_pci 0000:06:00.0: failed to start hw scan: -110 [ 1198.911926] ath11k_pci 0000:06:00.0: failed to start hw scan: -110 Change to set 11d state while disconnect, and the 11d scan will be started after the new hw scan in ath11k_mac_op_hw_scan(). Then the time cost of switching AP is small and not happened scan fail. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Fixes: 9dcf6808b253 ("ath11k: add 11d scan offload support") Signed-off-by: Wen Gong <quic_wgong@quicinc.com> --- v4: remove patch "[PATCH v3 2/2] wifi: ath11k: reduce the timeout value back for hw scan from 10 seconds to 1 second" v3: change code and log of "wifi: ath11k: reduce the timeout value back for hw scan from 10 seconds to 1 second" to handle the "failed to start hw scan: -110" correctly. v2: add "wifi: ath11k: change to set 11d state instead of start 11d scan while disconnect" drivers/net/wireless/ath/ath11k/mac.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) base-commit: c6d18be90f9b0c7fb64c6138b51c49151140fb57