@@ -2337,6 +2337,23 @@ static void ath12k_dp_rx_h_rate(struct ath12k *ar, struct hal_rx_desc *rx_desc,
rx_status->he_gi = ath12k_he_gi_to_nl80211_he_gi(sgi);
rx_status->bw = ath12k_mac_bw_to_mac80211_bw(bw);
break;
+ case RX_MSDU_START_PKT_TYPE_11BE:
+ rx_status->rate_idx = rate_mcs;
+
+ if (rate_mcs > ATH12K_EHT_MCS_MAX) {
+ ath12k_warn(ar->ab,
+ "Received with invalid mcs in EHT mode %d\n",
+ rate_mcs);
+ break;
+ }
+
+ rx_status->encoding = RX_ENC_EHT;
+ rx_status->nss = nss;
+ rx_status->eht.gi = ath12k_mac_eht_gi_to_nl80211_eht_gi(sgi);
+ rx_status->bw = ath12k_mac_bw_to_mac80211_bw(bw);
+ break;
+ default:
+ break;
}
}
@@ -2426,7 +2443,7 @@ static void ath12k_dp_rx_deliver_msdu(struct ath12k *ar, struct napi_struct *nap
spin_unlock_bh(&ab->base_lock);
ath12k_dbg(ab, ATH12K_DBG_DATA,
- "rx skb %p len %u peer %pM %d %s sn %u %s%s%s%s%s%s%s%s%s rate_idx %u vht_nss %u freq %u band %u flag 0x%x fcs-err %i mic-err %i amsdu-more %i\n",
+ "rx skb %p len %u peer %pM %d %s sn %u %s%s%s%s%s%s%s%s%s%s rate_idx %u vht_nss %u freq %u band %u flag 0x%x fcs-err %i mic-err %i amsdu-more %i\n",
msdu,
msdu->len,
peer ? peer->addr : NULL,
@@ -2437,6 +2454,7 @@ static void ath12k_dp_rx_deliver_msdu(struct ath12k *ar, struct napi_struct *nap
(status->encoding == RX_ENC_HT) ? "ht" : "",
(status->encoding == RX_ENC_VHT) ? "vht" : "",
(status->encoding == RX_ENC_HE) ? "he" : "",
+ (status->encoding == RX_ENC_EHT) ? "eht" : "",
(status->bw == RATE_INFO_BW_40) ? "40" : "",
(status->bw == RATE_INFO_BW_80) ? "80" : "",
(status->bw == RATE_INFO_BW_160) ? "160" : "",
@@ -637,6 +637,8 @@ enum rx_msdu_start_pkt_type {
RX_MSDU_START_PKT_TYPE_11N,
RX_MSDU_START_PKT_TYPE_11AC,
RX_MSDU_START_PKT_TYPE_11AX,
+ RX_MSDU_START_PKT_TYPE_11BA,
+ RX_MSDU_START_PKT_TYPE_11BE,
};
enum rx_msdu_start_sgi {
Currently, the receive rate of EHT of "iw dev xxx station dump" command always show an invalid value. This is because ath12k does not pass information about the rx_status of EHT to mac80211. So, mac80211 not calculate the receive rate. To address this issue, add logic for handling rx_status of EHT to the ath12k_dp_rx_h_rate() function. After that, "iw dev xxx station dump" show the correct receive rate. Such as: Station 00:03:7f:12:03:03 (on wlo1) inactive time: 48 ms rx bytes: 59226 rx packets: 320 tx bytes: 26556 tx packets: 191 tx retries: 99 tx failed: 0 beacon loss: 0 beacon rx: 79 rx drop misc: 68 signal: -95 dBm beacon signal avg: -20 dBm tx bitrate: 688.2 MBit/s 40MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0 tx duration: 0 us rx bitrate: 619.5 MBit/s 40MHz EHT-MCS 8 EHT-NSS 3 EHT-GI 0 This patch affects the station mode of WCN7850 and QCN9274. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.2.1-00201-QCAHKSWPL_SILICONZ-1 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> --- v5: no change v4: no change v3: no change v2: no change drivers/net/wireless/ath/ath12k/dp_rx.c | 20 +++++++++++++++++++- drivers/net/wireless/ath/ath12k/rx_desc.h | 2 ++ 2 files changed, 21 insertions(+), 1 deletion(-)