@@ -169,8 +169,14 @@ err_pci:
/* Get the word-offset for a SSB_SPROM_XXX define. */
#define SPOFF(offset) (((offset) - SSB_SPROM_BASE) / sizeof(u16))
/* Helper to extract some _offset, which is one of the SSB_SPROM_XXX defines. */
-#define SPEX(_outvar, _offset, _mask, _shift) \
+#define SPEX16(_outvar, _offset, _mask, _shift) \
out->_outvar = ((in[SPOFF(_offset)] & (_mask)) >> (_shift))
+#define SPEX32(_outvar, _offset, _mask, _shift) \
+ out->_outvar = ((((in[SPOFF((_offset)+2)] << sizeof(u16)) | \
+ in[SPOFF(_offset)]) & (_mask)) >> (_shift))
+#define SPEX(_outvar, _offset, _mask, _shift) \
+ SPEX16(_outvar, _offset, _mask, _shift)
+
static inline u8 ssb_crc8(u8 crc, u8 data)
{
@@ -480,6 +486,8 @@ static void sprom_extract_r8(struct ssb_sprom *out, const u16 *in)
SPEX(country_code, SSB_SPROM8_CCODE, 0xFFFF, 0);
SPEX(boardflags_lo, SSB_SPROM8_BFLLO, 0xFFFF, 0);
SPEX(boardflags_hi, SSB_SPROM8_BFLHI, 0xFFFF, 0);
+ SPEX(boardflags2_lo, SSB_SPROM8_BFL2LO, 0xFFFF, 0);
+ SPEX(boardflags2_hi, SSB_SPROM8_BFL2HI, 0xFFFF, 0);
SPEX(ant_available_a, SSB_SPROM8_ANTAVAIL, SSB_SPROM8_ANTAVAIL_A,
SSB_SPROM8_ANTAVAIL_A_SHIFT);
SPEX(ant_available_bg, SSB_SPROM8_ANTAVAIL, SSB_SPROM8_ANTAVAIL_BG,
@@ -490,12 +498,55 @@ static void sprom_extract_r8(struct ssb_sprom *out, const u16 *in)
SPEX(maxpwr_a, SSB_SPROM8_MAXP_A, SSB_SPROM8_MAXP_A_MASK, 0);
SPEX(itssi_a, SSB_SPROM8_MAXP_A, SSB_SPROM8_ITSSI_A,
SSB_SPROM8_ITSSI_A_SHIFT);
+ SPEX(maxpwr_ah, SSB_SPROM8_MAXP_AHL, SSB_SPROM8_MAXP_AH_MASK, 0);
+ SPEX(maxpwr_al, SSB_SPROM8_MAXP_AHL, SSB_SPROM8_MAXP_AL_MASK,
+ SSB_SPROM8_MAXP_AL_SHIFT);
SPEX(gpio0, SSB_SPROM8_GPIOA, SSB_SPROM8_GPIOA_P0, 0);
SPEX(gpio1, SSB_SPROM8_GPIOA, SSB_SPROM8_GPIOA_P1,
SSB_SPROM8_GPIOA_P1_SHIFT);
SPEX(gpio2, SSB_SPROM8_GPIOB, SSB_SPROM8_GPIOB_P2, 0);
SPEX(gpio3, SSB_SPROM8_GPIOB, SSB_SPROM8_GPIOB_P3,
SSB_SPROM8_GPIOB_P3_SHIFT);
+ SPEX(tri2g, SSB_SPROM8_TRI25G, SSB_SPROM8_TRI2G, 0);
+ SPEX(tri5g, SSB_SPROM8_TRI25G, SSB_SPROM8_TRI5G,
+ SSB_SPROM8_TRI5G_SHIFT);
+ SPEX(tri5gl, SSB_SPROM8_TRI5GHL, SSB_SPROM8_TRI5GL, 0);
+ SPEX(tri5gh, SSB_SPROM8_TRI5GHL, SSB_SPROM8_TRI5GH,
+ SSB_SPROM8_TRI5GH_SHIFT);
+ SPEX(rxpo2g, SSB_SPROM8_RXPO, SSB_SPROM8_RXPO2G, 0);
+ SPEX(rxpo5g, SSB_SPROM8_RXPO, SSB_SPROM8_RXPO5G,
+ SSB_SPROM8_RXPO5G_SHIFT);
+ SPEX(rssismf2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_RSSISMF2G, 0);
+ SPEX(rssismc2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_RSSISMC2G,
+ SSB_SPROM8_RSSISMC2G_SHIFT);
+ SPEX(rssisav2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_RSSISAV2G,
+ SSB_SPROM8_RSSISAV2G_SHIFT);
+ SPEX(bxa2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_BXA2G,
+ SSB_SPROM8_BXA2G_SHIFT);
+ SPEX(rssismf5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_RSSISMF5G, 0);
+ SPEX(rssismc5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_RSSISMC5G,
+ SSB_SPROM8_RSSISMC5G_SHIFT);
+ SPEX(rssisav5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_RSSISAV5G,
+ SSB_SPROM8_RSSISAV5G_SHIFT);
+ SPEX(bxa5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_BXA5G,
+ SSB_SPROM8_BXA5G_SHIFT);
+ SPEX(pa0b0, SSB_SPROM8_PA0B0, 0xFFFF, 0);
+ SPEX(pa0b1, SSB_SPROM8_PA0B1, 0xFFFF, 0);
+ SPEX(pa0b2, SSB_SPROM8_PA0B2, 0xFFFF, 0);
+ SPEX(pa1b0, SSB_SPROM8_PA1B0, 0xFFFF, 0);
+ SPEX(pa1b1, SSB_SPROM8_PA1B1, 0xFFFF, 0);
+ SPEX(pa1b2, SSB_SPROM8_PA1B2, 0xFFFF, 0);
+ SPEX(pa1lob0, SSB_SPROM8_PA1LOB0, 0xFFFF, 0);
+ SPEX(pa1lob1, SSB_SPROM8_PA1LOB1, 0xFFFF, 0);
+ SPEX(pa1lob2, SSB_SPROM8_PA1LOB2, 0xFFFF, 0);
+ SPEX(pa1hib0, SSB_SPROM8_PA1HIB0, 0xFFFF, 0);
+ SPEX(pa1hib1, SSB_SPROM8_PA1HIB1, 0xFFFF, 0);
+ SPEX(pa1hib2, SSB_SPROM8_PA1HIB2, 0xFFFF, 0);
+ SPEX(cck2gpo, SSB_SPROM8_CCK2GPO, 0xFFFF, 0);
+ SPEX32(ofdm2gpo, SSB_SPROM8_OFDM2GPO, 0xFFFFFFFF, 0);
+ SPEX32(ofdm5glpo, SSB_SPROM8_OFDM5GLPO, 0xFFFFFFFF, 0);
+ SPEX32(ofdm5gpo, SSB_SPROM8_OFDM5GPO, 0xFFFFFFFF, 0);
+ SPEX32(ofdm5ghpo, SSB_SPROM8_OFDM5GHPO, 0xFFFFFFFF, 0);
/* Extract the antenna gain values. */
SPEX(antenna_gain.ghz24.a0, SSB_SPROM8_AGAIN01,
@@ -27,24 +27,54 @@ struct ssb_sprom {
u8 et1mdcport; /* MDIO for enet1 */
u8 board_rev; /* Board revision number from SPROM. */
u8 country_code; /* Country Code */
- u8 ant_available_a; /* A-PHY antenna available bits (up to 4) */
- u8 ant_available_bg; /* B/G-PHY antenna available bits (up to 4) */
+ u8 ant_available_a; /* 2GHz antenna available bits (up to 4) */
+ u8 ant_available_bg; /* 5GHz antenna available bits (up to 4) */
u16 pa0b0;
u16 pa0b1;
u16 pa0b2;
u16 pa1b0;
u16 pa1b1;
u16 pa1b2;
+ u16 pa1lob0;
+ u16 pa1lob1;
+ u16 pa1lob2;
+ u16 pa1hib0;
+ u16 pa1hib1;
+ u16 pa1hib2;
u8 gpio0; /* GPIO pin 0 */
u8 gpio1; /* GPIO pin 1 */
u8 gpio2; /* GPIO pin 2 */
u8 gpio3; /* GPIO pin 3 */
- u16 maxpwr_a; /* A-PHY Amplifier Max Power (in dBm Q5.2) */
- u16 maxpwr_bg; /* B/G-PHY Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_bg; /* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_al; /* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_a; /* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_ah; /* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
u8 itssi_a; /* Idle TSSI Target for A-PHY */
u8 itssi_bg; /* Idle TSSI Target for B/G-PHY */
- u16 boardflags_lo; /* Boardflags (low 16 bits) */
- u16 boardflags_hi; /* Boardflags (high 16 bits) */
+ u8 tri2g; /* 2.4GHz TX isolation */
+ u8 tri5gl; /* 5.2GHz TX isolation */
+ u8 tri5g; /* 5.3GHz TX isolation */
+ u8 tri5gh; /* 5.8GHz TX isolation */
+ u8 rxpo2g; /* 2GHz RX power offset */
+ u8 rxpo5g; /* 5GHz RX power offset */
+ u8 rssisav2g; /* 2GHz RSSI params */
+ u8 rssismc2g;
+ u8 rssismf2g;
+ u8 bxa2g; /* 2GHz BX arch */
+ u8 rssisav5g; /* 5GHz RSSI params */
+ u8 rssismc5g;
+ u8 rssismf5g;
+ u8 bxa5g; /* 5GHz BX arch */
+ u16 cck2gpo; /* CCK power offset */
+ u32 ofdm2gpo; /* 2.4GHz OFDM power offset */
+ u32 ofdm5glpo; /* 5.2GHz OFDM power offset */
+ u32 ofdm5gpo; /* 5.3GHz OFDM power offset */
+ u32 ofdm5ghpo; /* 5.8GHz OFDM power offset */
+ u16 boardflags_lo; /* Board flags (bits 0-15) */
+ u16 boardflags_hi; /* Board flags (bits 16-31) */
+ u16 boardflags2_lo; /* Board flags (bits 32-47) */
+ u16 boardflags2_hi; /* Board flags (bits 48-63) */
+ /* TODO store board flags in a single u64 */
/* Antenna gain values for up to 4 antennas
* on each band. Values in dBm/4 (Q5.2). Negative gain means the
@@ -58,7 +88,7 @@ struct ssb_sprom {
} ghz5; /* 5GHz band */
} antenna_gain;
- /* TODO - add any parameters needed from rev 2, 3, or 4 SPROMs */
+ /* TODO - add any parameters needed from rev 2, 3, 4, 5 or 8 SPROMs */
};
/* Information about the PCB the circuitry is soldered on. */
@@ -162,7 +162,7 @@
/* SPROM shadow area. If not otherwise noted, fields are
* two bytes wide. Note that the SPROM can _only_ be read
- * in two-byte quantinies.
+ * in two-byte quantities.
*/
#define SSB_SPROMSIZE_WORDS 64
#define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16))
@@ -327,8 +327,11 @@
#define SSB_SPROM5_GPIOB_P3_SHIFT 8
/* SPROM Revision 8 */
-#define SSB_SPROM8_BFLLO 0x1084 /* Boardflags (low 16 bits) */
-#define SSB_SPROM8_BFLHI 0x1086 /* Boardflags Hi */
+#define SSB_SPROM8_BOARDREV 0x1082 /* Board revision */
+#define SSB_SPROM8_BFLLO 0x1084 /* Board flags (bits 0-15) */
+#define SSB_SPROM8_BFLHI 0x1086 /* Board flags (bits 16-31) */
+#define SSB_SPROM8_BFL2LO 0x1088 /* Board flags (bits 32-47) */
+#define SSB_SPROM8_BFL2HI 0x108A /* Board flags (bits 48-63) */
#define SSB_SPROM8_IL0MAC 0x108C /* 6 byte MAC address */
#define SSB_SPROM8_CCODE 0x1092 /* 2 byte country code */
#define SSB_SPROM8_ANTAVAIL 0x109C /* Antenna available bitfields*/
@@ -354,14 +357,63 @@
#define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */
#define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */
#define SSB_SPROM8_GPIOB_P3_SHIFT 8
-#define SSB_SPROM8_MAXP_BG 0x10C0 /* Max Power BG in path 1 */
-#define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */
+#define SSB_SPROM8_RSSIPARM2G 0x10A4 /* RSSI params for 2GHz */
+#define SSB_SPROM8_RSSISMF2G 0x000F
+#define SSB_SPROM8_RSSISMC2G 0x00F0
+#define SSB_SPROM8_RSSISMC2G_SHIFT 4
+#define SSB_SPROM8_RSSISAV2G 0x0700
+#define SSB_SPROM8_RSSISAV2G_SHIFT 8
+#define SSB_SPROM8_BXA2G 0x1800
+#define SSB_SPROM8_BXA2G_SHIFT 11
+#define SSB_SPROM8_RSSIPARM5G 0x10A6 /* RSSI params for 5GHz */
+#define SSB_SPROM8_RSSISMF5G 0x000F
+#define SSB_SPROM8_RSSISMC5G 0x00F0
+#define SSB_SPROM8_RSSISMC5G_SHIFT 4
+#define SSB_SPROM8_RSSISAV5G 0x0700
+#define SSB_SPROM8_RSSISAV5G_SHIFT 8
+#define SSB_SPROM8_BXA5G 0x1800
+#define SSB_SPROM8_BXA5G_SHIFT 11
+#define SSB_SPROM8_TRI25G 0x10A8 /* TX isolation 2.4&5.3GHz */
+#define SSB_SPROM8_TRI2G 0x00FF /* TX isolation 2.4GHz */
+#define SSB_SPROM8_TRI5G 0xFF00 /* TX isolation 5.3GHz */
+#define SSB_SPROM8_TRI5G_SHIFT 8
+#define SSB_SPROM8_TRI5GHL 0x10AA /* TX isolation 5.2/5.8GHz */
+#define SSB_SPROM8_TRI5GL 0x00FF /* TX isolation 5.2GHz */
+#define SSB_SPROM8_TRI5GH 0xFF00 /* TX isolation 5.8GHz */
+#define SSB_SPROM8_TRI5GH_SHIFT 8
+#define SSB_SPROM8_RXPO 0x10AC /* RX power offsets */
+#define SSB_SPROM8_RXPO2G 0x00FF /* 2GHz RX power offset */
+#define SSB_SPROM8_RXPO5G 0xFF00 /* 5GHz RX power offset */
+#define SSB_SPROM8_RXPO5G_SHIFT 8
+#define SSB_SPROM8_MAXP_BG 0x10C0 /* Max Power 2GHz in path 1 */
+#define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power 2GHz */
#define SSB_SPROM8_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */
#define SSB_SPROM8_ITSSI_BG_SHIFT 8
-#define SSB_SPROM8_MAXP_A 0x10C8 /* Max Power A in path 1 */
-#define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power A */
+#define SSB_SPROM8_PA0B0 0x10C2 /* 2GHz power amp settings */
+#define SSB_SPROM8_PA0B1 0x10C4
+#define SSB_SPROM8_PA0B2 0x10C6
+#define SSB_SPROM8_MAXP_A 0x10C8 /* Max Power 5.3GHz */
+#define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power 5.3GHz */
#define SSB_SPROM8_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */
#define SSB_SPROM8_ITSSI_A_SHIFT 8
+#define SSB_SPROM8_MAXP_AHL 0x10CA /* Max Power 5.2/5.8GHz */
+#define SSB_SPROM8_MAXP_AH_MASK 0x00FF /* Mask for Max Power 5.8GHz */
+#define SSB_SPROM8_MAXP_AL_MASK 0xFF00 /* Mask for Max Power 5.2GHz */
+#define SSB_SPROM8_MAXP_AL_SHIFT 8
+#define SSB_SPROM8_PA1B0 0x10CC /* 5.3GHz power amp settings */
+#define SSB_SPROM8_PA1B1 0x10CE
+#define SSB_SPROM8_PA1B2 0x10D0
+#define SSB_SPROM8_PA1LOB0 0x10D2 /* 5.2GHz power amp settings */
+#define SSB_SPROM8_PA1LOB1 0x10D4
+#define SSB_SPROM8_PA1LOB2 0x10D6
+#define SSB_SPROM8_PA1HIB0 0x10D8 /* 5.8GHz power amp settings */
+#define SSB_SPROM8_PA1HIB1 0x10DA
+#define SSB_SPROM8_PA1HIB2 0x10DC
+#define SSB_SPROM8_CCK2GPO 0x1140 /* CCK power offset */
+#define SSB_SPROM8_OFDM2GPO 0x1142 /* 2.4GHz OFDM power offset */
+#define SSB_SPROM8_OFDM5GPO 0x1146 /* 5.3GHz OFDM power offset */
+#define SSB_SPROM8_OFDM5GLPO 0x114A /* 5.2GHz OFDM power offset */
+#define SSB_SPROM8_OFDM5GHPO 0x114E /* 5.8GHz OFDM power offset */
/* Values for SSB_SPROM1_BINF_CCODE */
enum {
Also add a "SPEX32" macro for extracting 32-bit SPROM variables. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> --- I'm not quite sure that the SPEX32 macro is sane endianness-wise; please review it carefully. (In the future, we will probably need a SPEX64 macro too, to correctly extract boardflags.) drivers/ssb/pci.c | 53 +++++++++++++++++++++++++++++++++- include/linux/ssb/ssb.h | 44 +++++++++++++++++++++++---- include/linux/ssb/ssb_regs.h | 66 +++++++++++++++++++++++++++++++++++++---- 3 files changed, 148 insertions(+), 15 deletions(-)