@@ -1257,18 +1257,109 @@ static void lpphy_calibration(struct b43_wldev *dev)
b43_mac_enable(dev);
}
+static void lpphy_set_tssi_mux(struct b43_wldev *dev, enum tssi_mux_mode mode)
+{
+ if (mode != TSSI_MUX_EXT) {
+ b43_radio_set(dev, B2063_PA_SP1, 0x2);
+ b43_phy_set(dev, B43_PHY_OFDM(0xF3), 0x1000);
+ b43_radio_write(dev, B2063_PA_CTL10, 0x51);
+ if (mode == TSSI_MUX_POSTPA) {
+ b43_radio_mask(dev, B2063_PA_SP1, 0xFFFE);
+ b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0xFFC7);
+ } else {
+ b43_radio_maskset(dev, B2063_PA_SP1, 0xFFFE, 0x1);
+ b43_phy_maskset(dev, B43_LPPHY_AFE_CTL_OVRVAL,
+ 0xFFC7, 0x20);
+ }
+ } else {
+ B43_WARN_ON(1);
+ }
+}
+
+static void lpphy_tx_pctl_init_hw(struct b43_wldev *dev)
+{
+ u16 tmp;
+ int i;
+
+ //SPEC TODO Call LP PHY Clear TX Power offsets
+ for (i = 0; i < 64; i++) {
+ if (dev->phy.rev >= 2)
+ b43_lptab_write(dev, B43_LPTAB32(7, i + 1), i);
+ else
+ b43_lptab_write(dev, B43_LPTAB32(10, i + 1), i);
+ }
+
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_NNUM, 0xFF00, 0xFF);
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_NNUM, 0x8FFF, 0x5000);
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_IDLETSSI, 0xFFC0, 0x1F);
+ if (dev->phy.rev < 2) {
+ b43_phy_mask(dev, B43_LPPHY_LP_PHY_CTL, 0xEFFF);
+ b43_phy_maskset(dev, B43_LPPHY_LP_PHY_CTL, 0xDFFF, 0x2000);
+ } else {
+ b43_phy_mask(dev, B43_PHY_OFDM(0x103), 0xFFFE);
+ b43_phy_maskset(dev, B43_PHY_OFDM(0x103), 0xFFFB, 0x4);
+ b43_phy_maskset(dev, B43_PHY_OFDM(0x103), 0xFFEF, 0x10);
+ b43_radio_maskset(dev, B2063_IQ_CALIB_CTL2, 0xF3, 0x1);
+ lpphy_set_tssi_mux(dev, TSSI_MUX_POSTPA);
+ }
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_IDLETSSI, 0x7FFF, 0x8000);
+ b43_phy_mask(dev, B43_LPPHY_TX_PWR_CTL_DELTAPWR_LIMIT, 0xFF);
+ b43_phy_write(dev, B43_LPPHY_TX_PWR_CTL_DELTAPWR_LIMIT, 0xA);
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_CMD,
+ (u16)~B43_LPPHY_TX_PWR_CTL_CMD_MODE,
+ B43_LPPHY_TX_PWR_CTL_CMD_MODE_OFF);
+ b43_phy_mask(dev, B43_LPPHY_TX_PWR_CTL_NNUM, 0xF8FF);
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_CMD,
+ (u16)~B43_LPPHY_TX_PWR_CTL_CMD_MODE,
+ B43_LPPHY_TX_PWR_CTL_CMD_MODE_SW);
+
+ if (dev->phy.rev < 2) {
+ b43_phy_maskset(dev, B43_LPPHY_RF_OVERRIDE_0, 0xEFFF, 0x1000);
+ b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_VAL_0, 0xEFFF);
+ } else {
+ lpphy_set_tx_power_by_index(dev, 0x7F);
+ }
+
+ b43_dummy_transmission(dev, true, true);
+
+ tmp = b43_phy_read(dev, B43_LPPHY_TX_PWR_CTL_STAT);
+ if (tmp & 0x8000) {
+ b43_phy_maskset(dev, B43_LPPHY_TX_PWR_CTL_IDLETSSI,
+ 0xFFC0, (tmp & 0xFF) - 32);
+ }
+
+ b43_phy_mask(dev, B43_LPPHY_RF_OVERRIDE_0, 0xEFFF);
+
+ // (SPEC?) TODO Set "Target TX frequency" variable to 0
+ // SPEC FIXME "Set BB Multiplier to 0xE000" impossible - bb_mult is u8!
+}
+
+static void lpphy_tx_pctl_init_sw(struct b43_wldev *dev)
+{
+ struct lpphy_tx_gains gains;
+
+ if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
+ gains.gm = 4;
+ gains.pad = 12;
+ gains.pga = 12;
+ gains.dac = 0;
+ } else {
+ gains.gm = 7;
+ gains.pad = 14;
+ gains.pga = 15;
+ gains.dac = 0;
+ }
+ lpphy_set_tx_gains(dev, gains);
+ lpphy_set_bb_mult(dev, 150);
+}
+
/* Initialize TX power control */
static void lpphy_tx_pctl_init(struct b43_wldev *dev)
{
if (0/*FIXME HWPCTL capable */) {
- //TODO
+ lpphy_tx_pctl_init_hw(dev);
} else { /* This device is only software TX power control capable. */
- if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
- //TODO
- } else {
- //TODO
- }
- //TODO set BB multiplier to 0x0096
+ lpphy_tx_pctl_init_sw(dev);
}
}
@@ -886,6 +886,11 @@ struct b43_phy_lp {
u16 dig_flt_state[9];
};
+enum tssi_mux_mode {
+ TSSI_MUX_PREPA,
+ TSSI_MUX_POSTPA,
+ TSSI_MUX_EXT,
+};
struct b43_phy_operations;
extern const struct b43_phy_operations b43_phyops_lp;
The HW TX power control init still needs work. The SW init is complete according to the specs. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> --- v3: WARN_ON() setting TSSI mux mode to Ext, per Larry's suggestion. v2: Address Michael's comments, and update for the dummy transmission changes. This depends on both the rev0/1 RC calibration patch and the updated V4 dummy transmission patch I submitted earlier. Larry, please review the SPEC TODO/SPEC FIXME comments! drivers/net/wireless/b43/phy_lp.c | 105 ++++++++++++++++++++++++++++++++++--- drivers/net/wireless/b43/phy_lp.h | 5 ++ 2 files changed, 103 insertions(+), 7 deletions(-)