@@ -411,11 +411,11 @@ int wl1251_hw_init(struct wl1251 *wl)
goto out_free_data_path;
wl_mem_map = wl->target_mem_map;
- wl1251_info("%d tx blocks at 0x%x, %d rx blocks at 0x%x",
- wl_mem_map->num_tx_mem_blocks,
- wl->data_path->tx_control_addr,
- wl_mem_map->num_rx_mem_blocks,
- wl->data_path->rx_control_addr);
+ wl1251_debug(DEBUG_ALWAYS, "%d tx blocks at 0x%x, %d rx blocks at 0x%x",
+ wl_mem_map->num_tx_mem_blocks,
+ wl->data_path->tx_control_addr,
+ wl_mem_map->num_rx_mem_blocks,
+ wl->data_path->rx_control_addr);
return 0;
@@ -423,7 +423,7 @@ static int wl1251_op_start(struct ieee80211_hw *hw)
wl->state = WL1251_STATE_ON;
- wl1251_info("firmware booted (%s)", wl->fw_ver);
+ wl1251_debug(DEBUG_ALWAYS, "firmware booted (%s)", wl->fw_ver);
/* update hw/fw version info in wiphy struct */
wiphy->hw_version = wl->chip_id;
@@ -442,7 +442,7 @@ static void wl1251_op_stop(struct ieee80211_hw *hw)
{
struct wl1251 *wl = hw->priv;
- wl1251_info("down");
+ wl1251_debug(DEBUG_ALWAYS, "down");
wl1251_debug(DEBUG_MAC80211, "mac80211 stop");
@@ -290,12 +290,12 @@ static int wl1251_sdio_probe(struct sdio_func *func,
wl1251_sdio_ops.enable_irq = wl1251_enable_line_irq;
wl1251_sdio_ops.disable_irq = wl1251_disable_line_irq;
- wl1251_info("using dedicated interrupt line");
+ wl1251_debug(DEBUG_ALWAYS, "using dedicated interrupt line");
} else {
wl1251_sdio_ops.enable_irq = wl1251_sdio_enable_irq;
wl1251_sdio_ops.disable_irq = wl1251_sdio_disable_irq;
- wl1251_info("using SDIO interrupt");
+ wl1251_debug(DEBUG_ALWAYS, "using SDIO interrupt");
}
ret = wl1251_init_ieee80211(wl);
@@ -47,6 +47,7 @@ enum {
DEBUG_MAC80211 = BIT(11),
DEBUG_CMD = BIT(12),
DEBUG_ACX = BIT(13),
+ DEBUG_ALWAYS = BIT(31),
DEBUG_ALL = ~0,
};
@@ -54,12 +55,9 @@ enum {
#define DEBUG_DUMP_LIMIT 1024
-#define wl1251_info(fmt, arg...) \
- printk(KERN_DEBUG DRIVER_PREFIX fmt "\n", ##arg)
-
#define wl1251_debug(level, fmt, arg...) \
do { \
- if (level & DEBUG_LEVEL) \
+ if (level == DEBUG_ALWAYS || (level & DEBUG_LEVEL)) \
printk(KERN_DEBUG DRIVER_PREFIX fmt "\n", ##arg); \
} while (0)
These logging messages are always emitted at KERN_DEBUG. Add a DEBUG_ALWAYS enum to the debug type enum and convert the macro and uses from wl1251_info( to wl1251_debug(DEBUG_ALWAYS, Miscellanea: o Remove the now unused wl1251_info macro Signed-off-by: Joe Perches <joe@perches.com> --- drivers/net/wireless/ti/wl1251/init.c | 10 +++++----- drivers/net/wireless/ti/wl1251/main.c | 4 ++-- drivers/net/wireless/ti/wl1251/sdio.c | 4 ++-- drivers/net/wireless/ti/wl1251/wl1251.h | 6 ++---- 4 files changed, 11 insertions(+), 13 deletions(-)