[net-next,v3,0/8] TXGBE PHYLINK support

Message

Jiawen Wu April 19, 2023, 8:27 a.m. UTC

Implement I2C, SFP, GPIO and PHYLINK to setup TXGBE link and switch link
rate based on optical module information.

Because our I2C and PCS are based on Synopsys Designware IP-core, extend
the i2c-designware and pcs-xpcs driver to realize our functions.

v2 -> v3:
- delete own I2C bus master driver, support it in i2c-designware
- delete own PCS functions, remove pma configuration and 1000BASE-X mode
- add basic function for 10GBASE-R interface in pcs-xpcs
- add helper to get txgbe pointer from netdev

v1 -> v2:
- add comments to indicate GPIO lines
- add I2C write operation support
- modify GPIO direction functions
- rename functions related to PHY interface
- add condition on interface changing to re-config PCS
- add to set advertise and fix to get status for 1000BASE-X mode
- other redundant codes remove

Jiawen Wu (8):
  net: txgbe: Add software nodes to support phylink
  i2c: designware: Add driver support for Wangxun 10Gb NIC
  net: txgbe: Register I2C platform device
  net: txgbe: Add SFP module identify
  net: txgbe: Support GPIO to SFP socket
  net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS
  net: txgbe: Implement phylink pcs
  net: txgbe: Support phylink MAC layer

 drivers/i2c/busses/i2c-designware-common.c    |   4 +
 drivers/i2c/busses/i2c-designware-core.h      |   1 +
 drivers/i2c/busses/i2c-designware-master.c    |  91 ++-
 drivers/i2c/busses/i2c-designware-platdrv.c   |  36 +-
 drivers/net/ethernet/wangxun/Kconfig          |   6 +
 drivers/net/ethernet/wangxun/libwx/wx_lib.c   |   3 +-
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |   3 +
 drivers/net/ethernet/wangxun/txgbe/Makefile   |   1 +
 .../ethernet/wangxun/txgbe/txgbe_ethtool.c    |  28 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  63 +-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 585 ++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_phy.h    |  10 +
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  92 +++
 drivers/net/pcs/pcs-xpcs.c                    |  58 ++
 include/linux/pcs/pcs-xpcs.h                  |   1 +
 include/linux/platform_data/i2c-dw.h          |  15 +
 16 files changed, 960 insertions(+), 37 deletions(-)
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
 create mode 100644 include/linux/platform_data/i2c-dw.h

Comments

Vladimir Oltean April 19, 2023, 1:39 p.m. UTC | #1

On Wed, Apr 19, 2023 at 04:27:31PM +0800, Jiawen Wu wrote:
> Implement I2C, SFP, GPIO and PHYLINK to setup TXGBE link and switch link
> rate based on optical module information.
> 
> Because our I2C and PCS are based on Synopsys Designware IP-core, extend
> the i2c-designware and pcs-xpcs driver to realize our functions.

For next patch versions, please copy the maintainers/reviewers listed
under "SFF/SFP/SFP+ MODULE SUPPORT", "SOFTWARE NODES AND DEVICE PROPERTIES",
"ETHERNET PHY LIBRARY".