[vhost,v2,00/24] vdpa/mlx5: Pre-create HW VQs to reduce LM downtime

Message

Dragos Tatulea June 26, 2024, 10:26 a.m. UTC

According to the measurements for vDPA Live Migration downtime [0], one
large source of downtime is the creation of hardware VQs and their
associated resources on the devices on the destination VM.

Previous series ([1], [2]) addressed the source part of the Live
Migration downtime. This series addresses the destination part: instead
of creating hardware VQs and their dependent resources when the device
goes into the DRIVER_OK state (which is during downtime), create "blank"
VQs at device creation time and only modify them to the received
configuration before starting the VQs (DRIVER_OK state).

The caveat here is that mlx5_vdpa VQs don't support modifying the VQ
size. VQs will be created with a convenient default size and when this
size is changed, they will be recreated.

The beginning of the series consists of refactorings and preparation.

After that, some preparations are made:
- Allow creation of "blank" VQs by not configuring them during
  create_virtqueue() if there are no modified fields.
- The VQ Init to Ready state transition is consolidated into the
  resume_vq().
- Add error handling to suspend/resume code paths.

Then VQs are created at device creation time.

Finally, the special cases that need full VQ resource recreation are
handled.

On a 64 CPU, 256 GB VM with 1 vDPA device of 16 VQps, the full VQ
resource creation + resume time was ~370ms. Now it's down to 60 ms
(only VQ config and resume). The measurements were done on a ConnectX6DX
based vDPA device.

[0] https://lore.kernel.org/qemu-devel/[e-mail]/
[1] https://lore.kernel.org/lkml/[e-mail]
[2] https://lore.kernel.org/lkml/[e-mail]

---
Changes in v2:
- Renamed a function based on v1 review.
- Addressed small nits from v1 review.
- Added improvement numbers in commit message instead of only cover
  letter.
- Link to v1: https://lore.kernel.org/r/[e-mail]

---
Dragos Tatulea (24):
      vdpa/mlx5: Clarify meaning thorough function rename
      vdpa/mlx5: Make setup/teardown_vq_resources() symmetrical
      vdpa/mlx5: Drop redundant code
      vdpa/mlx5: Drop redundant check in teardown_virtqueues()
      vdpa/mlx5: Iterate over active VQs during suspend/resume
      vdpa/mlx5: Remove duplicate suspend code
      vdpa/mlx5: Initialize and reset device with one queue pair
      vdpa/mlx5: Clear and reinitialize software VQ data on reset
      vdpa/mlx5: Rename init_mvqs
      vdpa/mlx5: Add support for modifying the virtio_version VQ field
      vdpa/mlx5: Add support for modifying the VQ features field
      vdpa/mlx5: Set an initial size on the VQ
      vdpa/mlx5: Start off rqt_size with max VQPs
      vdpa/mlx5: Set mkey modified flags on all VQs
      vdpa/mlx5: Allow creation of blank VQs
      vdpa/mlx5: Accept Init -> Ready VQ transition in resume_vq()
      vdpa/mlx5: Add error code for suspend/resume VQ
      vdpa/mlx5: Consolidate all VQ modify to Ready to use resume_vq()
      vdpa/mlx5: Forward error in suspend/resume device
      vdpa/mlx5: Use suspend/resume during VQP change
      vdpa/mlx5: Pre-create hardware VQs at vdpa .dev_add time
      vdpa/mlx5: Re-create HW VQs under certain conditions
      vdpa/mlx5: Don't reset VQs more than necessary
      vdpa/mlx5: Don't enable non-active VQs in .set_vq_ready()

 drivers/vdpa/mlx5/net/mlx5_vnet.c  | 429 +++++++++++++++++++++++++------------
 drivers/vdpa/mlx5/net/mlx5_vnet.h  |   1 +
 include/linux/mlx5/mlx5_ifc_vdpa.h |   2 +
 3 files changed, 293 insertions(+), 139 deletions(-)
---
base-commit: c8fae27d141a32a1624d0d0d5419d94252824498
change-id: 20240617-stage-vdpa-vq-precreate-76df151bed08

Best regards,