@@ -657,15 +657,13 @@ enum rtl_register_content {
#define INTR_LINK 0x0004
-#define RTL8153_MAX_PACKET 9216 /* 9K */
-#define RTL8153_MAX_MTU (RTL8153_MAX_PACKET - VLAN_ETH_HLEN - \
- ETH_FCS_LEN)
#define RTL8152_RMS (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)
#define RTL8153_RMS RTL8153_MAX_PACKET
#define RTL8152_TX_TIMEOUT (5 * HZ)
#define RTL8152_NAPI_WEIGHT 64
-#define rx_reserved_size(x) ((x) + VLAN_ETH_HLEN + ETH_FCS_LEN + \
- sizeof(struct rx_desc) + RX_ALIGN)
+#define mtu_to_size(m) ((m) + VLAN_ETH_HLEN + ETH_FCS_LEN)
+#define size_to_mtu(s) ((s) - VLAN_ETH_HLEN - ETH_FCS_LEN)
+#define rx_reserved_size(x) (mtu_to_size(x) + sizeof(struct rx_desc) + RX_ALIGN)
/* rtl8152 flags */
enum rtl8152_flags {
@@ -795,6 +793,7 @@ struct r8152 {
bool (*in_nway)(struct r8152 *tp);
void (*hw_phy_cfg)(struct r8152 *tp);
void (*autosuspend_en)(struct r8152 *tp, bool enable);
+ void (*change_mtu)(struct r8152 *tp);
} rtl_ops;
struct ups_info {
@@ -1021,8 +1020,7 @@ enum tx_csum_stat {
static const int multicast_filter_limit = 32;
static unsigned int agg_buf_sz = 16384;
-#define RTL_LIMITED_TSO_SIZE (agg_buf_sz - sizeof(struct tx_desc) - \
- VLAN_ETH_HLEN - ETH_FCS_LEN)
+#define RTL_LIMITED_TSO_SIZE (size_to_mtu(agg_buf_sz) - sizeof(struct tx_desc))
static
int get_registers(struct r8152 *tp, u16 value, u16 index, u16 size, void *data)
@@ -2632,10 +2630,7 @@ static void rtl8152_nic_reset(struct r8152 *tp)
static void set_tx_qlen(struct r8152 *tp)
{
- struct net_device *netdev = tp->netdev;
-
- tp->tx_qlen = agg_buf_sz / (netdev->mtu + VLAN_ETH_HLEN + ETH_FCS_LEN +
- sizeof(struct tx_desc));
+ tp->tx_qlen = agg_buf_sz / (mtu_to_size(tp->netdev->mtu) + sizeof(struct tx_desc));
}
static inline u8 rtl8152_get_speed(struct r8152 *tp)
@@ -4724,6 +4719,12 @@ static void r8153b_hw_phy_cfg(struct r8152 *tp)
set_bit(PHY_RESET, &tp->flags);
}
+static void rtl8153_change_mtu(struct r8152 *tp)
+{
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, mtu_to_size(tp->netdev->mtu));
+ ocp_write_byte(tp, MCU_TYPE_PLA, PLA_MTPS, MTPS_JUMBO);
+}
+
static void r8153_first_init(struct r8152 *tp)
{
u32 ocp_data;
@@ -4756,9 +4757,7 @@ static void r8153_first_init(struct r8152 *tp)
rtl_rx_vlan_en(tp, tp->netdev->features & NETIF_F_HW_VLAN_CTAG_RX);
- ocp_data = tp->netdev->mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
- ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, ocp_data);
- ocp_write_byte(tp, MCU_TYPE_PLA, PLA_MTPS, MTPS_JUMBO);
+ rtl8153_change_mtu(tp);
ocp_data = ocp_read_word(tp, MCU_TYPE_PLA, PLA_TCR0);
ocp_data |= TCR0_AUTO_FIFO;
@@ -4793,8 +4792,7 @@ static void r8153_enter_oob(struct r8152 *tp)
wait_oob_link_list_ready(tp);
- ocp_data = tp->netdev->mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
- ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, ocp_data);
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, mtu_to_size(tp->netdev->mtu));
switch (tp->version) {
case RTL_VER_03:
@@ -6494,12 +6492,21 @@ static int rtl8152_change_mtu(struct net_device *dev, int new_mtu)
dev->mtu = new_mtu;
if (netif_running(dev)) {
- u32 rms = new_mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
-
- ocp_write_word(tp, MCU_TYPE_PLA, PLA_RMS, rms);
+ if (tp->rtl_ops.change_mtu)
+ tp->rtl_ops.change_mtu(tp);
- if (netif_carrier_ok(dev))
- r8153_set_rx_early_size(tp);
+ if (netif_carrier_ok(dev)) {
+ netif_stop_queue(dev);
+ napi_disable(&tp->napi);
+ tasklet_disable(&tp->tx_tl);
+ tp->rtl_ops.disable(tp);
+ tp->rtl_ops.enable(tp);
+ rtl_start_rx(tp);
+ tasklet_enable(&tp->tx_tl);
+ napi_enable(&tp->napi);
+ rtl8152_set_rx_mode(dev);
+ netif_wake_queue(dev);
+ }
}
mutex_unlock(&tp->control);
@@ -6588,6 +6595,7 @@ static int rtl_ops_init(struct r8152 *tp)
ops->in_nway = rtl8153_in_nway;
ops->hw_phy_cfg = r8153_hw_phy_cfg;
ops->autosuspend_en = rtl8153_runtime_enable;
+ ops->change_mtu = rtl8153_change_mtu;
if (tp->udev->speed < USB_SPEED_SUPER)
tp->rx_buf_sz = 16 * 1024;
else
@@ -6609,6 +6617,7 @@ static int rtl_ops_init(struct r8152 *tp)
ops->in_nway = rtl8153_in_nway;
ops->hw_phy_cfg = r8153b_hw_phy_cfg;
ops->autosuspend_en = rtl8153b_runtime_enable;
+ ops->change_mtu = rtl8153_change_mtu;
tp->rx_buf_sz = 32 * 1024;
tp->eee_en = true;
tp->eee_adv = MDIO_EEE_1000T | MDIO_EEE_100TX;
@@ -6829,7 +6838,7 @@ static int rtl8152_probe(struct usb_interface *intf,
netdev->max_mtu = ETH_DATA_LEN;
break;
default:
- netdev->max_mtu = RTL8153_MAX_MTU;
+ netdev->max_mtu = size_to_mtu(9 * 1024);
break;
}
The different chips may have different requests when changing mtu. Therefore, add a new help function of rtl_ops to change mtu. Besides, reset the tx/rx after changing mtu. Additionally, add mtu_to_size() and size_to_mtu() macros to simplify the code. Signed-off-by: Hayes Wang <hayeswang@realtek.com> --- drivers/net/usb/r8152.c | 53 ++++++++++++++++++++++++----------------- 1 file changed, 31 insertions(+), 22 deletions(-)