diff mbox series

[net-next,4/5] net: phy: marvell10g: change MACTYPE if underlying MAC does not support it

Message ID 20201028221427.22968-5-kabel@kernel.org (mailing list archive)
State Superseded
Delegated to: Netdev Maintainers
Headers show
Series Support for RollBall 10G copper SFP modules | expand

Commit Message

Marek Behún Oct. 28, 2020, 10:14 p.m. UTC 
RollBall SFPs contain a Marvell 88X3310 PHY, but by default the MACTYPE
is set to 10GBASE-R with Rate Matching.

Some devices (for example those based on Armada 38x) only support up to
2500base-x SerDes modes.

Change the PHY's MACTYPE to 4 (which means changing between 10gbase-r,
5gbase-r, 2500base-x ans SGMII depending on copper speed) if this is the
case (which is infered from phydev->interface).

Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/marvell10g.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

Comments

Russell King (Oracle) Oct. 29, 2020, 1:21 p.m. UTC | #1 
On Wed, Oct 28, 2020 at 11:14:26PM +0100, Marek Behún wrote:
> RollBall SFPs contain a Marvell 88X3310 PHY, but by default the MACTYPE
> is set to 10GBASE-R with Rate Matching.
> 
> Some devices (for example those based on Armada 38x) only support up to
> 2500base-x SerDes modes.
> 
> Change the PHY's MACTYPE to 4 (which means changing between 10gbase-r,
> 5gbase-r, 2500base-x ans SGMII depending on copper speed) if this is the
> case (which is infered from phydev->interface).
> 
> Signed-off-by: Marek Behún <kabel@kernel.org>
> Cc: Andrew Lunn <andrew@lunn.ch>
> Cc: Russell King <rmk+kernel@armlinux.org.uk>

This'll do as a stop-gap until we have a better way to determine which
MACTYPE mode we should be using.
diff mbox series

Patch

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 1901ba277413..9e8e9aa66972 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -453,6 +453,33 @@  static bool mv3310_has_pma_ngbaset_quirk(struct phy_device *phydev)
 		MV_PHY_ALASKA_NBT_QUIRK_MASK) == MV_PHY_ALASKA_NBT_QUIRK_REV;
 }
 
+static int mv3310_select_mactype(struct phy_device *phydev)
+{
+	int mac_type, ret;
+
+	/* On some devices the MAC does not support 10G mode, but may support
+	 * lower modes, such as SGMII or 2500base-x.
+	 * By changing MACTYPE of the PHY to 4 in this case, we ensure that
+	 * the MAC will link with the PHY at least for these lower speeds.
+	 */
+	switch (phydev->interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_2500BASEX:
+		mac_type = 4;
+		break;
+	default:
+		return 0;
+	}
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
+				     MV_V2_PORT_MAC_TYPE_MASK, mac_type);
+	if (ret <= 0)
+		return ret;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
+			      MV_V2_PORT_CTRL_SWRST, MV_V2_PORT_CTRL_SWRST);
+}
+
 static int mv3310_config_init(struct phy_device *phydev)
 {
 	struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev);
@@ -474,6 +501,10 @@  static int mv3310_config_init(struct phy_device *phydev)
 	if (err)
 		return err;
 
+	err = mv3310_select_mactype(phydev);
+	if (err)
+		return err;
+
 	val = phy_read_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL);
 	if (val < 0)
 		return val;