diff mbox series

[v2,net-next,1/2] dt-bindings: net: nfc: s3fwrn5: Change I2C interrupt trigger type

Message ID 20201208141012.6033-2-bongsu.jeon@samsung.com (mailing list archive)
State Accepted
Delegated to: Netdev Maintainers
Headers show
Series nfc: s3fwrn5: Change I2C interrupt trigger to EDGE_RISING | expand

Checks

Context Check Description
netdev/cover_letter success Link
netdev/fixes_present success Link
netdev/patch_count success Link
netdev/tree_selection success Clearly marked for net-next
netdev/subject_prefix success Link
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param success Was 0 now: 0
netdev/build_32bit success Errors and warnings before: 0 this patch: 0
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 8 lines checked
netdev/build_allmodconfig_warn success Errors and warnings before: 0 this patch: 0
netdev/header_inline success Link
netdev/stable success Stable not CCed

Commit Message

Bongsu Jeon Dec. 8, 2020, 2:10 p.m. UTC 
From: Bongsu Jeon <bongsu.jeon@samsung.com>

Change interrupt trigger from IRQ_TYPE_LEVEL_HIGH to IRQ_TYPE_EDGE_RISING
 for stable NFC I2C interrupt handling.
Samsung's NFC Firmware sends an i2c frame as below.
1. NFC Firmware sets the GPIO(interrupt pin) high when there is an i2c
 frame to send.
2. If the CPU's I2C master has received the i2c frame, NFC F/W sets the
GPIO low.
NFC driver's i2c interrupt handler would be called in the abnormal case
as the NFC FW task of number 2 is delayed because of other high priority
tasks.
In that case, NFC driver will try to receive the i2c frame but there isn't
 any i2c frame to send in NFC.
It would cause an I2C communication problem. This case would hardly happen.
But, I changed the interrupt as a defense code.
If Driver uses the TRIGGER_RISING instead of the LEVEL trigger,
there would be no problem even if the NFC FW task is delayed.

Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
---
 Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml b/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml
index ca3904bf90e0..477066e2b821 100644
--- a/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml
+++ b/Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml
@@ -76,7 +76,7 @@  examples:
             reg = <0x27>;
 
             interrupt-parent = <&gpa1>;
-            interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+            interrupts = <3 IRQ_TYPE_EDGE_RISING>;
 
             en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>;
             wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>;