@@ -2570,6 +2570,17 @@ static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port,
mcr |= PMCR_RX_FC_EN;
}
+ if (mode == MLO_AN_PHY && phydev && phy_init_eee(phydev, 0) >= 0) {
+ switch (speed) {
+ case SPEED_1000:
+ mcr |= PMCR_FORCE_EEE1G;
+ break;
+ case SPEED_100:
+ mcr |= PMCR_FORCE_EEE100;
+ break;
+ }
+ }
+
mt7530_set(priv, MT7530_PMCR_P(port), mcr);
}
@@ -2800,6 +2811,36 @@ mt753x_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
return priv->info->phy_write(ds, port, regnum, val);
}
+static int mt753x_get_mac_eee(struct dsa_switch *ds, int port,
+ struct ethtool_eee *e)
+{
+ struct mt7530_priv *priv = ds->priv;
+ u32 eeecr = mt7530_read(priv, MT7530_PMEEECR_P(port));
+
+ e->tx_lpi_enabled = !(eeecr & LPI_MODE_EN);
+ e->tx_lpi_timer = GET_LPI_THRESH(eeecr);
+
+ return 0;
+}
+
+static int mt753x_set_mac_eee(struct dsa_switch *ds, int port,
+ struct ethtool_eee *e)
+{
+ struct mt7530_priv *priv = ds->priv;
+ u32 set, mask = LPI_THRESH_MASK | LPI_MODE_EN;
+
+ if (e->tx_lpi_timer > 0xFFF)
+ return -EINVAL;
+
+ set = SET_LPI_THRESH(e->tx_lpi_timer);
+ if (!e->tx_lpi_enabled)
+ /* Force LPI Mode without a delay */
+ set |= LPI_MODE_EN;
+ mt7530_rmw(priv, MT7530_PMEEECR_P(port), mask, set);
+
+ return 0;
+}
+
static const struct dsa_switch_ops mt7530_switch_ops = {
.get_tag_protocol = mtk_get_tag_protocol,
.setup = mt753x_setup,
@@ -2835,6 +2876,8 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
.phylink_mac_an_restart = mt753x_phylink_mac_an_restart,
.phylink_mac_link_down = mt753x_phylink_mac_link_down,
.phylink_mac_link_up = mt753x_phylink_mac_link_up,
+ .get_mac_eee = mt753x_get_mac_eee,
+ .set_mac_eee = mt753x_set_mac_eee,
};
static const struct mt753x_info mt753x_table[] = {
@@ -257,6 +257,8 @@ enum mt7530_vlan_port_attr {
#define PMCR_RX_EN BIT(13)
#define PMCR_BACKOFF_EN BIT(9)
#define PMCR_BACKPR_EN BIT(8)
+#define PMCR_FORCE_EEE1G BIT(7)
+#define PMCR_FORCE_EEE100 BIT(6)
#define PMCR_TX_FC_EN BIT(5)
#define PMCR_RX_FC_EN BIT(4)
#define PMCR_FORCE_SPEED_1000 BIT(3)
@@ -281,7 +283,8 @@ enum mt7530_vlan_port_attr {
#define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
- PMCR_FORCE_FDX | PMCR_FORCE_LNK)
+ PMCR_FORCE_FDX | PMCR_FORCE_LNK | \
+ PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100)
#define PMCR_CPU_PORT_SETTING(id) (PMCR_FORCE_MODE_ID((id)) | \
PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
@@ -290,6 +293,15 @@ enum mt7530_vlan_port_attr {
PMCR_FORCE_SPEED_1000 | \
PMCR_FORCE_FDX | PMCR_FORCE_LNK)
+#define MT7530_PMEEECR_P(x) (0x3004 + (x) * 0x100)
+#define WAKEUP_TIME_1000(x) (((x) & 0xFF) << 24)
+#define WAKEUP_TIME_100(x) (((x) & 0xFF) << 16)
+#define LPI_THRESH_MASK GENMASK(15, 4)
+#define LPI_THRESH_SHT 4
+#define SET_LPI_THRESH(x) (((x) << LPI_THRESH_SHT) & LPI_THRESH_MASK)
+#define GET_LPI_THRESH(x) (((x) & LPI_THRESH_MASK) >> LPI_THRESH_SHT)
+#define LPI_MODE_EN BIT(0)
+
#define MT7530_PMSR_P(x) (0x3008 + (x) * 0x100)
#define PMSR_EEE1G BIT(7)
#define PMSR_EEE100M BIT(6)
This patch adds EEE support. Signed-off-by: René van Dorst <opensource@vdorst.com> --- v1 -> v2: - Refactor the mt753x_{get,set}_mac_eee(). As DENQ Qingfang mentioned, most things are set else were. These functions only set/report the LPI timeout value/LPI timeout enable bit. - Removed the variable "eee_enabled", don't need too track the EEE status. - Refactor mt753x_phylink_mac_link_up(). phy_init_eee() reports is the EEE is active, this function also checks the PHY, duplex and broken DTS modes. When active set the MAC EEE bit based on the speed. - Add {GET,SET)_LPI_THRESH(x) macro - PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100 are now placed in the right MASK variable drivers/net/dsa/mt7530.c | 43 ++++++++++++++++++++++++++++++++++++++++ drivers/net/dsa/mt7530.h | 14 ++++++++++++- 2 files changed, 56 insertions(+), 1 deletion(-)