@@ -15,6 +15,7 @@
#include <linux/phy.h>
#include <linux/etherdevice.h>
#include <linux/if_bridge.h>
+#include <linux/micrel_phy.h>
#include <net/dsa.h>
#include <net/switchdev.h>
@@ -731,88 +732,88 @@ static void ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
u8 p = phy;
switch (reg) {
- case PHY_REG_CTRL:
+ case MII_BMCR:
ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
if (restart & PORT_PHY_LOOPBACK)
- data |= PHY_LOOPBACK;
+ data |= BMCR_LOOPBACK;
if (ctrl & PORT_FORCE_100_MBIT)
- data |= PHY_SPEED_100MBIT;
+ data |= BMCR_SPEED100;
if (ksz_is_ksz88x3(dev)) {
if ((ctrl & PORT_AUTO_NEG_ENABLE))
- data |= PHY_AUTO_NEG_ENABLE;
+ data |= BMCR_ANENABLE;
} else {
if (!(ctrl & PORT_AUTO_NEG_DISABLE))
- data |= PHY_AUTO_NEG_ENABLE;
+ data |= BMCR_ANENABLE;
}
if (restart & PORT_POWER_DOWN)
- data |= PHY_POWER_DOWN;
+ data |= BMCR_PDOWN;
if (restart & PORT_AUTO_NEG_RESTART)
- data |= PHY_AUTO_NEG_RESTART;
+ data |= BMCR_ANRESTART;
if (ctrl & PORT_FORCE_FULL_DUPLEX)
- data |= PHY_FULL_DUPLEX;
+ data |= BMCR_FULLDPLX;
if (speed & PORT_HP_MDIX)
- data |= PHY_HP_MDIX;
+ data |= KSZ886X_BMCR_HP_MDIX;
if (restart & PORT_FORCE_MDIX)
- data |= PHY_FORCE_MDIX;
+ data |= KSZ886X_BMCR_FORCE_MDI;
if (restart & PORT_AUTO_MDIX_DISABLE)
- data |= PHY_AUTO_MDIX_DISABLE;
+ data |= KSZ886X_BMCR_DISABLE_AUTO_MDIX;
if (restart & PORT_TX_DISABLE)
- data |= PHY_TRANSMIT_DISABLE;
+ data |= KSZ886X_BMCR_DISABLE_TRANSMIT;
if (restart & PORT_LED_OFF)
- data |= PHY_LED_DISABLE;
+ data |= KSZ886X_BMCR_DISABLE_LED;
break;
- case PHY_REG_STATUS:
+ case MII_BMSR:
ksz_pread8(dev, p, regs[P_LINK_STATUS], &link);
- data = PHY_100BTX_FD_CAPABLE |
- PHY_100BTX_CAPABLE |
- PHY_10BT_FD_CAPABLE |
- PHY_10BT_CAPABLE |
- PHY_AUTO_NEG_CAPABLE;
+ data = BMSR_100FULL |
+ BMSR_100HALF |
+ BMSR_10FULL |
+ BMSR_10HALF |
+ BMSR_ANEGCAPABLE;
if (link & PORT_AUTO_NEG_COMPLETE)
- data |= PHY_AUTO_NEG_ACKNOWLEDGE;
+ data |= BMSR_ANEGCOMPLETE;
if (link & PORT_STAT_LINK_GOOD)
- data |= PHY_LINK_STATUS;
+ data |= BMSR_LSTATUS;
break;
- case PHY_REG_ID_1:
+ case MII_PHYSID1:
data = KSZ8795_ID_HI;
break;
- case PHY_REG_ID_2:
+ case MII_PHYSID2:
if (ksz_is_ksz88x3(dev))
data = KSZ8863_ID_LO;
else
data = KSZ8795_ID_LO;
break;
- case PHY_REG_AUTO_NEGOTIATION:
+ case MII_ADVERTISE:
ksz_pread8(dev, p, regs[P_LOCAL_CTRL], &ctrl);
- data = PHY_AUTO_NEG_802_3;
+ data = ADVERTISE_CSMA;
if (ctrl & PORT_AUTO_NEG_SYM_PAUSE)
- data |= PHY_AUTO_NEG_SYM_PAUSE;
+ data |= ADVERTISE_PAUSE_CAP;
if (ctrl & PORT_AUTO_NEG_100BTX_FD)
- data |= PHY_AUTO_NEG_100BTX_FD;
+ data |= ADVERTISE_100FULL;
if (ctrl & PORT_AUTO_NEG_100BTX)
- data |= PHY_AUTO_NEG_100BTX;
+ data |= ADVERTISE_100HALF;
if (ctrl & PORT_AUTO_NEG_10BT_FD)
- data |= PHY_AUTO_NEG_10BT_FD;
+ data |= ADVERTISE_10FULL;
if (ctrl & PORT_AUTO_NEG_10BT)
- data |= PHY_AUTO_NEG_10BT;
+ data |= ADVERTISE_10HALF;
break;
- case PHY_REG_REMOTE_CAPABILITY:
+ case MII_LPA:
ksz_pread8(dev, p, regs[P_REMOTE_STATUS], &link);
- data = PHY_AUTO_NEG_802_3;
+ data = LPA_SLCT;
if (link & PORT_REMOTE_SYM_PAUSE)
- data |= PHY_AUTO_NEG_SYM_PAUSE;
+ data |= LPA_PAUSE_CAP;
if (link & PORT_REMOTE_100BTX_FD)
- data |= PHY_AUTO_NEG_100BTX_FD;
+ data |= LPA_100FULL;
if (link & PORT_REMOTE_100BTX)
- data |= PHY_AUTO_NEG_100BTX;
+ data |= LPA_100HALF;
if (link & PORT_REMOTE_10BT_FD)
- data |= PHY_AUTO_NEG_10BT_FD;
+ data |= LPA_10FULL;
if (link & PORT_REMOTE_10BT)
- data |= PHY_AUTO_NEG_10BT;
- if (data & ~PHY_AUTO_NEG_802_3)
- data |= PHY_REMOTE_ACKNOWLEDGE_NOT;
+ data |= LPA_10HALF;
+ if (data & ~LPA_SLCT)
+ data |= LPA_LPACK;
break;
default:
processed = false;
@@ -830,14 +831,14 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
u8 p = phy;
switch (reg) {
- case PHY_REG_CTRL:
+ case MII_BMCR:
/* Do not support PHY reset function. */
- if (val & PHY_RESET)
+ if (val & BMCR_RESET)
break;
ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
data = speed;
- if (val & PHY_HP_MDIX)
+ if (val & KSZ886X_BMCR_HP_MDIX)
data |= PORT_HP_MDIX;
else
data &= ~PORT_HP_MDIX;
@@ -846,12 +847,12 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
data = ctrl;
if (ksz_is_ksz88x3(dev)) {
- if ((val & PHY_AUTO_NEG_ENABLE))
+ if ((val & BMCR_ANENABLE))
data |= PORT_AUTO_NEG_ENABLE;
else
data &= ~PORT_AUTO_NEG_ENABLE;
} else {
- if (!(val & PHY_AUTO_NEG_ENABLE))
+ if (!(val & BMCR_ANENABLE))
data |= PORT_AUTO_NEG_DISABLE;
else
data &= ~PORT_AUTO_NEG_DISABLE;
@@ -861,11 +862,11 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
data |= PORT_AUTO_NEG_DISABLE;
}
- if (val & PHY_SPEED_100MBIT)
+ if (val & BMCR_SPEED100)
data |= PORT_FORCE_100_MBIT;
else
data &= ~PORT_FORCE_100_MBIT;
- if (val & PHY_FULL_DUPLEX)
+ if (val & BMCR_FULLDPLX)
data |= PORT_FORCE_FULL_DUPLEX;
else
data &= ~PORT_FORCE_FULL_DUPLEX;
@@ -873,38 +874,38 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
ksz_pwrite8(dev, p, regs[P_FORCE_CTRL], data);
ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
data = restart;
- if (val & PHY_LED_DISABLE)
+ if (val & KSZ886X_BMCR_DISABLE_LED)
data |= PORT_LED_OFF;
else
data &= ~PORT_LED_OFF;
- if (val & PHY_TRANSMIT_DISABLE)
+ if (val & KSZ886X_BMCR_DISABLE_TRANSMIT)
data |= PORT_TX_DISABLE;
else
data &= ~PORT_TX_DISABLE;
- if (val & PHY_AUTO_NEG_RESTART)
+ if (val & BMCR_ANRESTART)
data |= PORT_AUTO_NEG_RESTART;
else
data &= ~(PORT_AUTO_NEG_RESTART);
- if (val & PHY_POWER_DOWN)
+ if (val & BMCR_PDOWN)
data |= PORT_POWER_DOWN;
else
data &= ~PORT_POWER_DOWN;
- if (val & PHY_AUTO_MDIX_DISABLE)
+ if (val & KSZ886X_BMCR_DISABLE_AUTO_MDIX)
data |= PORT_AUTO_MDIX_DISABLE;
else
data &= ~PORT_AUTO_MDIX_DISABLE;
- if (val & PHY_FORCE_MDIX)
+ if (val & KSZ886X_BMCR_FORCE_MDI)
data |= PORT_FORCE_MDIX;
else
data &= ~PORT_FORCE_MDIX;
- if (val & PHY_LOOPBACK)
+ if (val & BMCR_LOOPBACK)
data |= PORT_PHY_LOOPBACK;
else
data &= ~PORT_PHY_LOOPBACK;
if (data != restart)
ksz_pwrite8(dev, p, regs[P_NEG_RESTART_CTRL], data);
break;
- case PHY_REG_AUTO_NEGOTIATION:
+ case MII_ADVERTISE:
ksz_pread8(dev, p, regs[P_LOCAL_CTRL], &ctrl);
data = ctrl;
data &= ~(PORT_AUTO_NEG_SYM_PAUSE |
@@ -912,15 +913,15 @@ static void ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
PORT_AUTO_NEG_100BTX |
PORT_AUTO_NEG_10BT_FD |
PORT_AUTO_NEG_10BT);
- if (val & PHY_AUTO_NEG_SYM_PAUSE)
+ if (val & ADVERTISE_PAUSE_CAP)
data |= PORT_AUTO_NEG_SYM_PAUSE;
- if (val & PHY_AUTO_NEG_100BTX_FD)
+ if (val & ADVERTISE_100FULL)
data |= PORT_AUTO_NEG_100BTX_FD;
- if (val & PHY_AUTO_NEG_100BTX)
+ if (val & ADVERTISE_100HALF)
data |= PORT_AUTO_NEG_100BTX;
- if (val & PHY_AUTO_NEG_10BT_FD)
+ if (val & ADVERTISE_10FULL)
data |= PORT_AUTO_NEG_10BT_FD;
- if (val & PHY_AUTO_NEG_10BT)
+ if (val & ADVERTISE_10HALF)
data |= PORT_AUTO_NEG_10BT;
if (data != ctrl)
ksz_pwrite8(dev, p, regs[P_LOCAL_CTRL], data);
@@ -744,68 +744,6 @@
#define PORT_ACL_FORCE_DLR_MISS BIT(0)
-#ifndef PHY_REG_CTRL
-#define PHY_REG_CTRL 0
-
-#define PHY_RESET BIT(15)
-#define PHY_LOOPBACK BIT(14)
-#define PHY_SPEED_100MBIT BIT(13)
-#define PHY_AUTO_NEG_ENABLE BIT(12)
-#define PHY_POWER_DOWN BIT(11)
-#define PHY_MII_DISABLE BIT(10)
-#define PHY_AUTO_NEG_RESTART BIT(9)
-#define PHY_FULL_DUPLEX BIT(8)
-#define PHY_COLLISION_TEST_NOT BIT(7)
-#define PHY_HP_MDIX BIT(5)
-#define PHY_FORCE_MDIX BIT(4)
-#define PHY_AUTO_MDIX_DISABLE BIT(3)
-#define PHY_REMOTE_FAULT_DISABLE BIT(2)
-#define PHY_TRANSMIT_DISABLE BIT(1)
-#define PHY_LED_DISABLE BIT(0)
-
-#define PHY_REG_STATUS 1
-
-#define PHY_100BT4_CAPABLE BIT(15)
-#define PHY_100BTX_FD_CAPABLE BIT(14)
-#define PHY_100BTX_CAPABLE BIT(13)
-#define PHY_10BT_FD_CAPABLE BIT(12)
-#define PHY_10BT_CAPABLE BIT(11)
-#define PHY_MII_SUPPRESS_CAPABLE_NOT BIT(6)
-#define PHY_AUTO_NEG_ACKNOWLEDGE BIT(5)
-#define PHY_REMOTE_FAULT BIT(4)
-#define PHY_AUTO_NEG_CAPABLE BIT(3)
-#define PHY_LINK_STATUS BIT(2)
-#define PHY_JABBER_DETECT_NOT BIT(1)
-#define PHY_EXTENDED_CAPABILITY BIT(0)
-
-#define PHY_REG_ID_1 2
-#define PHY_REG_ID_2 3
-
-#define PHY_REG_AUTO_NEGOTIATION 4
-
-#define PHY_AUTO_NEG_NEXT_PAGE_NOT BIT(15)
-#define PHY_AUTO_NEG_REMOTE_FAULT_NOT BIT(13)
-#define PHY_AUTO_NEG_SYM_PAUSE BIT(10)
-#define PHY_AUTO_NEG_100BT4 BIT(9)
-#define PHY_AUTO_NEG_100BTX_FD BIT(8)
-#define PHY_AUTO_NEG_100BTX BIT(7)
-#define PHY_AUTO_NEG_10BT_FD BIT(6)
-#define PHY_AUTO_NEG_10BT BIT(5)
-#define PHY_AUTO_NEG_SELECTOR 0x001F
-#define PHY_AUTO_NEG_802_3 0x0001
-
-#define PHY_REG_REMOTE_CAPABILITY 5
-
-#define PHY_REMOTE_NEXT_PAGE_NOT BIT(15)
-#define PHY_REMOTE_ACKNOWLEDGE_NOT BIT(14)
-#define PHY_REMOTE_REMOTE_FAULT_NOT BIT(13)
-#define PHY_REMOTE_SYM_PAUSE BIT(10)
-#define PHY_REMOTE_100BTX_FD BIT(8)
-#define PHY_REMOTE_100BTX BIT(7)
-#define PHY_REMOTE_10BT_FD BIT(6)
-#define PHY_REMOTE_10BT BIT(5)
-#endif
-
#define KSZ8795_ID_HI 0x0022
#define KSZ8795_ID_LO 0x1550
#define KSZ8863_ID_LO 0x1430
@@ -25,6 +25,7 @@
#include <linux/crc32.h>
#include <linux/sched.h>
#include <linux/slab.h>
+#include <linux/micrel_phy.h>
/* DMA Registers */
@@ -271,84 +272,15 @@
#define KS884X_PHY_CTRL_OFFSET 0x00
-/* Mode Control Register */
-#define PHY_REG_CTRL 0
-
-#define PHY_RESET 0x8000
-#define PHY_LOOPBACK 0x4000
-#define PHY_SPEED_100MBIT 0x2000
-#define PHY_AUTO_NEG_ENABLE 0x1000
-#define PHY_POWER_DOWN 0x0800
-#define PHY_MII_DISABLE 0x0400
-#define PHY_AUTO_NEG_RESTART 0x0200
-#define PHY_FULL_DUPLEX 0x0100
-#define PHY_COLLISION_TEST 0x0080
-#define PHY_HP_MDIX 0x0020
-#define PHY_FORCE_MDIX 0x0010
-#define PHY_AUTO_MDIX_DISABLE 0x0008
-#define PHY_REMOTE_FAULT_DISABLE 0x0004
-#define PHY_TRANSMIT_DISABLE 0x0002
-#define PHY_LED_DISABLE 0x0001
-
#define KS884X_PHY_STATUS_OFFSET 0x02
-/* Mode Status Register */
-#define PHY_REG_STATUS 1
-
-#define PHY_100BT4_CAPABLE 0x8000
-#define PHY_100BTX_FD_CAPABLE 0x4000
-#define PHY_100BTX_CAPABLE 0x2000
-#define PHY_10BT_FD_CAPABLE 0x1000
-#define PHY_10BT_CAPABLE 0x0800
-#define PHY_MII_SUPPRESS_CAPABLE 0x0040
-#define PHY_AUTO_NEG_ACKNOWLEDGE 0x0020
-#define PHY_REMOTE_FAULT 0x0010
-#define PHY_AUTO_NEG_CAPABLE 0x0008
-#define PHY_LINK_STATUS 0x0004
-#define PHY_JABBER_DETECT 0x0002
-#define PHY_EXTENDED_CAPABILITY 0x0001
-
#define KS884X_PHY_ID_1_OFFSET 0x04
#define KS884X_PHY_ID_2_OFFSET 0x06
-/* PHY Identifier Registers */
-#define PHY_REG_ID_1 2
-#define PHY_REG_ID_2 3
-
#define KS884X_PHY_AUTO_NEG_OFFSET 0x08
-/* Auto-Negotiation Advertisement Register */
-#define PHY_REG_AUTO_NEGOTIATION 4
-
-#define PHY_AUTO_NEG_NEXT_PAGE 0x8000
-#define PHY_AUTO_NEG_REMOTE_FAULT 0x2000
-/* Not supported. */
-#define PHY_AUTO_NEG_ASYM_PAUSE 0x0800
-#define PHY_AUTO_NEG_SYM_PAUSE 0x0400
-#define PHY_AUTO_NEG_100BT4 0x0200
-#define PHY_AUTO_NEG_100BTX_FD 0x0100
-#define PHY_AUTO_NEG_100BTX 0x0080
-#define PHY_AUTO_NEG_10BT_FD 0x0040
-#define PHY_AUTO_NEG_10BT 0x0020
-#define PHY_AUTO_NEG_SELECTOR 0x001F
-#define PHY_AUTO_NEG_802_3 0x0001
-
-#define PHY_AUTO_NEG_PAUSE (PHY_AUTO_NEG_SYM_PAUSE | PHY_AUTO_NEG_ASYM_PAUSE)
-
#define KS884X_PHY_REMOTE_CAP_OFFSET 0x0A
-/* Auto-Negotiation Link Partner Ability Register */
-#define PHY_REG_REMOTE_CAPABILITY 5
-
-#define PHY_REMOTE_NEXT_PAGE 0x8000
-#define PHY_REMOTE_ACKNOWLEDGE 0x4000
-#define PHY_REMOTE_REMOTE_FAULT 0x2000
-#define PHY_REMOTE_SYM_PAUSE 0x0400
-#define PHY_REMOTE_100BTX_FD 0x0100
-#define PHY_REMOTE_100BTX 0x0080
-#define PHY_REMOTE_10BT_FD 0x0040
-#define PHY_REMOTE_10BT 0x0020
-
/* P1VCT */
#define KS884X_P1VCT_P 0x04F0
#define KS884X_P1PHYCTRL_P 0x04F2
@@ -2886,15 +2818,6 @@ static void sw_block_addr(struct ksz_hw *hw)
}
}
-#define PHY_LINK_SUPPORT \
- (PHY_AUTO_NEG_ASYM_PAUSE | \
- PHY_AUTO_NEG_SYM_PAUSE | \
- PHY_AUTO_NEG_100BT4 | \
- PHY_AUTO_NEG_100BTX_FD | \
- PHY_AUTO_NEG_100BTX | \
- PHY_AUTO_NEG_10BT_FD | \
- PHY_AUTO_NEG_10BT)
-
static inline void hw_r_phy_ctrl(struct ksz_hw *hw, int phy, u16 *data)
{
*data = readw(hw->io + phy + KS884X_PHY_CTRL_OFFSET);
@@ -3238,16 +3161,18 @@ static void determine_flow_ctrl(struct ksz_hw *hw, struct ksz_port *port,
rx = tx = 0;
if (port->force_link)
rx = tx = 1;
- if (remote & PHY_AUTO_NEG_SYM_PAUSE) {
- if (local & PHY_AUTO_NEG_SYM_PAUSE) {
+ if (remote & LPA_PAUSE_CAP) {
+ if (local & ADVERTISE_PAUSE_CAP) {
rx = tx = 1;
- } else if ((remote & PHY_AUTO_NEG_ASYM_PAUSE) &&
- (local & PHY_AUTO_NEG_PAUSE) ==
- PHY_AUTO_NEG_ASYM_PAUSE) {
+ } else if ((remote & LPA_PAUSE_ASYM) &&
+ (local &
+ (ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM)) ==
+ ADVERTISE_PAUSE_ASYM) {
tx = 1;
}
- } else if (remote & PHY_AUTO_NEG_ASYM_PAUSE) {
- if ((local & PHY_AUTO_NEG_PAUSE) == PHY_AUTO_NEG_PAUSE)
+ } else if (remote & LPA_PAUSE_ASYM) {
+ if ((local & (ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM))
+ == (ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM))
rx = 1;
}
if (!hw->ksz_switch)
@@ -3428,16 +3353,16 @@ static void port_force_link_speed(struct ksz_port *port)
phy = KS884X_PHY_1_CTRL_OFFSET + p * PHY_CTRL_INTERVAL;
hw_r_phy_ctrl(hw, phy, &data);
- data &= ~PHY_AUTO_NEG_ENABLE;
+ data &= ~BMCR_ANENABLE;
if (10 == port->speed)
- data &= ~PHY_SPEED_100MBIT;
+ data &= ~BMCR_SPEED100;
else if (100 == port->speed)
- data |= PHY_SPEED_100MBIT;
+ data |= BMCR_SPEED100;
if (1 == port->duplex)
- data &= ~PHY_FULL_DUPLEX;
+ data &= ~BMCR_FULLDPLX;
else if (2 == port->duplex)
- data |= PHY_FULL_DUPLEX;
+ data |= BMCR_FULLDPLX;
hw_w_phy_ctrl(hw, phy, data);
}
}
@@ -45,4 +45,17 @@
#define MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SCEW 0x104
#define MICREL_KSZ9021_RGMII_RX_DATA_PAD_SCEW 0x105
+/* Device specific MII_BMCR (Reg 0) bits */
+/* 1 = HP Auto MDI/MDI-X mode, 0 = Microchip Auto MDI/MDI-X mode */
+#define KSZ886X_BMCR_HP_MDIX BIT(5)
+/* 1 = Force MDI (transmit on RXP/RXM pins), 0 = Normal operation
+ * (transmit on TXP/TXM pins)
+ */
+#define KSZ886X_BMCR_FORCE_MDI BIT(4)
+/* 1 = Disable auto MDI-X */
+#define KSZ886X_BMCR_DISABLE_AUTO_MDIX BIT(3)
+#define KSZ886X_BMCR_DISABLE_FAR_END_FAULT BIT(2)
+#define KSZ886X_BMCR_DISABLE_TRANSMIT BIT(1)
+#define KSZ886X_BMCR_DISABLE_LED BIT(0)
+
#endif /* _MICREL_PHY_H */