@@ -1038,7 +1038,7 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
enum mhi_ee_type current_ee;
enum dev_st_transition next_state;
struct device *dev = &mhi_cntrl->mhi_dev->dev;
- u32 val;
+ u32 interval_us = 25000; /* poll register field every 25 milliseconds */
int ret;
dev_info(dev, "Requested to power ON\n");
@@ -1055,10 +1055,6 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
mutex_lock(&mhi_cntrl->pm_mutex);
mhi_cntrl->pm_state = MHI_PM_DISABLE;
- ret = mhi_init_irq_setup(mhi_cntrl);
- if (ret)
- goto error_setup_irq;
-
/* Setup BHI INTVEC */
write_lock_irq(&mhi_cntrl->pm_lock);
mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
@@ -1072,7 +1068,7 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
dev_err(dev, "%s is not a valid EE for power on\n",
TO_MHI_EXEC_STR(current_ee));
ret = -EIO;
- goto error_async_power_up;
+ goto error_exit;
}
state = mhi_get_mhi_state(mhi_cntrl);
@@ -1081,20 +1077,12 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
if (state == MHI_STATE_SYS_ERR) {
mhi_set_mhi_state(mhi_cntrl, MHI_STATE_RESET);
- ret = wait_event_timeout(mhi_cntrl->state_event,
- MHI_PM_IN_FATAL_STATE(mhi_cntrl->pm_state) ||
- mhi_read_reg_field(mhi_cntrl,
- mhi_cntrl->regs,
- MHICTRL,
- MHICTRL_RESET_MASK,
- MHICTRL_RESET_SHIFT,
- &val) ||
- !val,
- msecs_to_jiffies(mhi_cntrl->timeout_ms));
- if (!ret) {
- ret = -EIO;
+ ret = mhi_poll_reg_field(mhi_cntrl, mhi_cntrl->regs, MHICTRL,
+ MHICTRL_RESET_MASK, MHICTRL_RESET_SHIFT, 0,
+ interval_us);
+ if (ret) {
dev_info(dev, "Failed to reset MHI due to syserr state\n");
- goto error_async_power_up;
+ goto error_exit;
}
/*
@@ -1104,6 +1092,10 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
}
+ ret = mhi_init_irq_setup(mhi_cntrl);
+ if (ret)
+ goto error_exit;
+
/* Transition to next state */
next_state = MHI_IN_PBL(current_ee) ?
DEV_ST_TRANSITION_PBL : DEV_ST_TRANSITION_READY;
@@ -1116,10 +1108,7 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
return 0;
-error_async_power_up:
- mhi_deinit_free_irq(mhi_cntrl);
-
-error_setup_irq:
+error_exit:
mhi_cntrl->pm_state = MHI_PM_DISABLE;
mutex_unlock(&mhi_cntrl->pm_mutex);
During SYS_ERR condition, as a response to the MHI_RESET from host, some devices tend to issue BHI interrupt without clearing the SYS_ERR state in the device. This creates a race condition and causes a failure in booting up the device. The issue is seen on the Sierra Wireless EM9191 modem during SYS_ERR handling in mhi_async_power_up(). Once the host detects that the device is in SYS_ERR state, it issues MHI_RESET and waits for the device to process the reset request. During this time, the device triggers the BHI interrupt to the host without clearing SYS_ERR condition. So the host starts handling the SYS_ERR condition again. To fix this issue, let's register the IRQ handler only after handling the SYS_ERR check to avoid getting spurious IRQs from the device. Cc: stable@vger.kernel.org Fixes: e18d4e9fa79b ("bus: mhi: core: Handle syserr during power_up") Reported-by: Aleksander Morgado <aleksander@aleksander.es> Tested-by: Aleksander Morgado <aleksander@aleksander.es> Tested-by: Thomas Perrot <thomas.perrot@bootlin.com> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- drivers/bus/mhi/core/pm.c | 35 ++++++++++++----------------------- 1 file changed, 12 insertions(+), 23 deletions(-)