@@ -105,6 +105,7 @@
#define RTL8365MB_CHIP_ID_8365MB_VC 0x6367
#define RTL8365MB_CPU_PORT_NUM_8365MB_VC 6
#define RTL8365MB_LEARN_LIMIT_MAX_8365MB_VC 2112
+static const int rtl8365mb_extint_port_map[] = { -1, -1, -1, -1, -1, -1, 1 };
/* Family-specific data and limits */
#define RTL8365MB_PHYADDRMAX 7
@@ -191,7 +192,7 @@
/* The PHY OCP addresses of PHY registers 0~31 start here */
#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400
-/* EXT port interface mode values - used in DIGITAL_INTERFACE_SELECT */
+/* EXT interface port mode values - used in DIGITAL_INTERFACE_SELECT */
#define RTL8365MB_EXT_PORT_MODE_DISABLE 0
#define RTL8365MB_EXT_PORT_MODE_RGMII 1
#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2
@@ -207,39 +208,56 @@
#define RTL8365MB_EXT_PORT_MODE_1000X 12
#define RTL8365MB_EXT_PORT_MODE_100FX 13
-/* EXT port interface mode configuration registers 0~1 */
-#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305
-#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3
-#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extport) \
- (RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 + \
- ((_extport) >> 1) * (0x13C3 - 0x1305))
-#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extport) \
- (0xF << (((_extport) % 2)))
-#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extport) \
- (((_extport) % 2) * 4)
-
-/* EXT port RGMII TX/RX delay configuration registers 1~2 */
-#define RTL8365MB_EXT_RGMXF_REG1 0x1307
-#define RTL8365MB_EXT_RGMXF_REG2 0x13C5
-#define RTL8365MB_EXT_RGMXF_REG(_extport) \
- (RTL8365MB_EXT_RGMXF_REG1 + \
- (((_extport) >> 1) * (0x13C5 - 0x1307)))
+/* Realtek docs and driver uses logic number as EXT_PORT0=16, EXT_PORT1=17,
+ * EXT_PORT2=18, to interact with switch ports. That logic number is internally
+ * converted to either a physical port number (0..9) or an external interface id (0..2),
+ * depending on which function was called. The external interface id is calculated as
+ * (ext_id=logic_port-15), while the logical to physical map depends on the chip id/version.
+ *
+ * EXT_PORT0 mentioned in datasheets and rtl8367c driver is used in this driver
+ * as extid==1, EXT_PORT2, mentioned in Realtek rtl8367c driver for 10-port switches,
+ * would have an ext_id of 3 (out of range for most extint macros) and ext_id 0 does
+ * not seem to be used as well for this family.
+ */
+
+/* EXT interface mode configuration registers 0~1 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305 /* EXT1 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3 /* EXT2 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extint) \
+ ((_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 : \
+ (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 : \
+ 0x0)
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extint) \
+ (0xF << (((_extint) % 2)))
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extint) \
+ (((_extint) % 2) * 4)
+
+/* EXT interface RGMII TX/RX delay configuration registers 0~2 */
+#define RTL8365MB_EXT_RGMXF_REG0 0x1306 /* EXT0 */
+#define RTL8365MB_EXT_RGMXF_REG1 0x1307 /* EXT1 */
+#define RTL8365MB_EXT_RGMXF_REG2 0x13C5 /* EXT2 */
+#define RTL8365MB_EXT_RGMXF_REG(_extint) \
+ ((_extint) == 0 ? RTL8365MB_EXT_RGMXF_REG0 : \
+ (_extint) == 1 ? RTL8365MB_EXT_RGMXF_REG1 : \
+ (_extint) == 2 ? RTL8365MB_EXT_RGMXF_REG2 : \
+ 0x0)
#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007
#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008
-/* External port speed values - used in DIGITAL_INTERFACE_FORCE */
+/* External interface port speed values - used in DIGITAL_INTERFACE_FORCE */
#define RTL8365MB_PORT_SPEED_10M 0
#define RTL8365MB_PORT_SPEED_100M 1
#define RTL8365MB_PORT_SPEED_1000M 2
-/* EXT port force configuration registers 0~2 */
-#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310
-#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311
-#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4
-#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extport) \
- (RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 + \
- ((_extport) & 0x1) + \
- ((((_extport) >> 1) & 0x1) * (0x13C4 - 0x1310)))
+/* EXT interface force configuration registers 0~2 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310 /* EXT0 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311 /* EXT1 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4 /* EXT2 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extint) \
+ ((_extint) == 0 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 : \
+ (_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 : \
+ (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 : \
+ 0x0)
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080
#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040
@@ -755,20 +773,25 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
struct dsa_port *dp;
int tx_delay = 0;
int rx_delay = 0;
- int ext_port;
+ int ext_int;
u32 val;
int ret;
- if (port == priv->cpu_port) {
- ext_port = 1;
- } else {
- dev_err(priv->dev, "only one EXT port is currently supported\n");
+ if (port != priv->cpu_port) {
+ dev_err(priv->dev, "only one EXT interface is currently supported\n");
return -EINVAL;
}
dp = dsa_to_port(priv->ds, port);
dn = dp->dn;
+ ext_int = rtl8365mb_extint_port_map[port];
+
+ if (ext_int <= 0) {
+ dev_err(priv->dev, "Port %d is not an external interface port\n", port);
+ return -EINVAL;
+ }
+
/* Set the RGMII TX/RX delay
*
* The Realtek vendor driver indicates the following possible
@@ -798,7 +821,7 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
tx_delay = val / 2;
else
dev_warn(priv->dev,
- "EXT port TX delay must be 0 or 2 ns\n");
+ "EXT interface TX delay must be 0 or 2 ns\n");
}
if (!of_property_read_u32(dn, "rx-internal-delay-ps", &val)) {
@@ -808,11 +831,11 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
rx_delay = val;
else
dev_warn(priv->dev,
- "EXT port RX delay must be 0 to 2.1 ns\n");
+ "EXT interface RX delay must be 0 to 2.1 ns\n");
}
ret = regmap_update_bits(
- priv->map, RTL8365MB_EXT_RGMXF_REG(ext_port),
+ priv->map, RTL8365MB_EXT_RGMXF_REG(ext_int),
RTL8365MB_EXT_RGMXF_TXDELAY_MASK |
RTL8365MB_EXT_RGMXF_RXDELAY_MASK,
FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) |
@@ -821,11 +844,11 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
return ret;
ret = regmap_update_bits(
- priv->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(ext_port),
- RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(ext_port),
+ priv->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(ext_int),
+ RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(ext_int),
RTL8365MB_EXT_PORT_MODE_RGMII
<< RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(
- ext_port));
+ ext_int));
if (ret)
return ret;
@@ -841,14 +864,19 @@ static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
u32 r_duplex;
u32 r_speed;
u32 r_link;
- int ext_port;
+ int ext_int;
int val;
int ret;
- if (port == priv->cpu_port) {
- ext_port = 1;
- } else {
- dev_err(priv->dev, "only one EXT port is currently supported\n");
+ if (port != priv->cpu_port) {
+ dev_err(priv->dev, "only one EXT interface is currently supported\n");
+ return -EINVAL;
+ }
+
+ ext_int = rtl8365mb_extint_port_map[port];
+
+ if (ext_int <= 0) {
+ dev_err(priv->dev, "Port %d is not an external interface port\n", port);
return -EINVAL;
}
@@ -898,7 +926,7 @@ static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
r_duplex) |
FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed);
ret = regmap_write(priv->map,
- RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(ext_port),
+ RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(ext_int),
val);
if (ret)
return ret;
@@ -1831,10 +1859,6 @@ static int rtl8365mb_setup(struct dsa_switch *ds)
if (dsa_is_unused_port(priv->ds, i))
continue;
- /* Set up per-port private data */
- p->priv = priv;
- p->index = i;
-
/* Forward only to the CPU */
ret = rtl8365mb_port_set_isolation(priv, i, BIT(priv->cpu_port));
if (ret)
@@ -1850,6 +1874,10 @@ static int rtl8365mb_setup(struct dsa_switch *ds)
* administratively down by default.
*/
rtl8365mb_port_stp_state_set(priv->ds, i, BR_STATE_DISABLED);
+
+ /* Set up per-port private data */
+ p->priv = priv;
+ p->index = i;
}
/* Set maximum packet length to 1536 bytes */
"extport" 0, 1, 2 was used to reference external ports id (ext0, ext1, ext2). Meanwhile, port 0..9 is used as switch ports, including external ports. "extport" was renamed to extint to make it clear it does not mean the port number but the external interface number id. The macros that map extint numbers to registers addresses now use inline ifs instead of binary arithmetic. Realtek uses in docs and drivers EXT_PORT0 (GMAC1) and EXT_PORT1 (GMAC2), with EXT_PORT0 being converted to ext_id == 1 and so on. It might introduce some confusing while reading datasheets but it will not be exposed to users. "extint" was hardcoded to 1. However, some chips have multiple external interfaces. It's not right to assume the CPU port uses extint 1 nor that all extint are CPU ports. Now it came from a map between port number and external interface id number. This patch still does not allow multiple CPU ports nor extint as a non CPU port. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> --- drivers/net/dsa/realtek/rtl8365mb.c | 124 +++++++++++++++++----------- 1 file changed, 76 insertions(+), 48 deletions(-)