@@ -15,6 +15,7 @@
#include <linux/of_mdio.h>
#include <linux/phy.h>
#include <linux/platform_device.h>
+#include <linux/property.h>
#include <linux/regmap.h>
#define MSCC_MIIM_REG_STATUS 0x0
@@ -36,11 +37,19 @@
#define PHY_CFG_PHY_RESET (BIT(5) | BIT(6) | BIT(7) | BIT(8))
#define MSCC_PHY_REG_PHY_STATUS 0x4
+#define LAN966X_CUPHY_COMMON_CFG 0x0
+#define CUPHY_COMMON_CFG_RESET_N BIT(0)
+
+struct mscc_miim_info {
+ unsigned int phy_reset_offset;
+ unsigned int phy_reset_bits;
+};
+
struct mscc_miim_dev {
struct regmap *regs;
int mii_status_offset;
struct regmap *phy_regs;
- int phy_reset_offset;
+ const struct mscc_miim_info *info;
};
/* When high resolution timers aren't built-in: we can't use usleep_range() as
@@ -157,27 +166,29 @@ static int mscc_miim_write(struct mii_bus *bus, int mii_id,
static int mscc_miim_reset(struct mii_bus *bus)
{
struct mscc_miim_dev *miim = bus->priv;
- int offset = miim->phy_reset_offset;
- int reset_bits = PHY_CFG_PHY_ENA | PHY_CFG_PHY_COMMON_RESET |
- PHY_CFG_PHY_RESET;
+ unsigned int offset, bits;
int ret;
- if (miim->phy_regs) {
- ret = regmap_write(miim->phy_regs, offset, 0);
- if (ret < 0) {
- WARN_ONCE(1, "mscc reset set error %d\n", ret);
- return ret;
- }
+ if (!miim->phy_regs)
+ return 0;
- ret = regmap_write(miim->phy_regs, offset, reset_bits);
- if (ret < 0) {
- WARN_ONCE(1, "mscc reset clear error %d\n", ret);
- return ret;
- }
+ offset = miim->info->phy_reset_offset;
+ bits = miim->info->phy_reset_bits;
+
+ ret = regmap_update_bits(miim->phy_regs, offset, bits, 0);
+ if (ret < 0) {
+ WARN_ONCE(1, "mscc reset set error %d\n", ret);
+ return ret;
+ }
- mdelay(500);
+ ret = regmap_update_bits(miim->phy_regs, offset, bits, bits);
+ if (ret < 0) {
+ WARN_ONCE(1, "mscc reset clear error %d\n", ret);
+ return ret;
}
+ mdelay(500);
+
return 0;
}
@@ -272,7 +283,10 @@ static int mscc_miim_probe(struct platform_device *pdev)
miim = bus->priv;
miim->phy_regs = phy_regmap;
- miim->phy_reset_offset = MSCC_PHY_REG_PHY_CFG;
+
+ miim->info = device_get_match_data(&pdev->dev);
+ if (!miim->info)
+ return -EINVAL;
ret = of_mdiobus_register(bus, pdev->dev.of_node);
if (ret < 0) {
@@ -294,8 +308,25 @@ static int mscc_miim_remove(struct platform_device *pdev)
return 0;
}
+static const struct mscc_miim_info mscc_ocelot_miim_info = {
+ .phy_reset_offset = MSCC_PHY_REG_PHY_CFG,
+ .phy_reset_bits = PHY_CFG_PHY_ENA | PHY_CFG_PHY_COMMON_RESET |
+ PHY_CFG_PHY_RESET,
+};
+
+static const struct mscc_miim_info microchip_lan966x_miim_info = {
+ .phy_reset_offset = LAN966X_CUPHY_COMMON_CFG,
+ .phy_reset_bits = CUPHY_COMMON_CFG_RESET_N,
+};
+
static const struct of_device_id mscc_miim_match[] = {
- { .compatible = "mscc,ocelot-miim" },
+ {
+ .compatible = "mscc,ocelot-miim",
+ .data = &mscc_ocelot_miim_info
+ }, {
+ .compatible = "microchip,lan966x-miim",
+ .data = µchip_lan966x_miim_info
+ },
{ }
};
MODULE_DEVICE_TABLE(of, mscc_miim_match);
The LAN966x has two internal PHYs which are in reset by default. The driver already supported the internal PHYs of the SparX-5. Now add support for the LAN966x, too. Add a new compatible to distinguish them. The LAN966x has additional control bits in this register, thus convert the regmap_write() to regmap_update_bits() to leave the remaining bits untouched. This doesn't change anything for the SparX-5 SoC, because there, the register consists only of reset bits. Signed-off-by: Michael Walle <michael@walle.cc> --- drivers/net/mdio/mdio-mscc-miim.c | 67 ++++++++++++++++++++++--------- 1 file changed, 49 insertions(+), 18 deletions(-)