@@ -51,6 +51,11 @@ The following is a list of 3rd party SFP+ modules that have been tested and veri
| WTD | SFP+ | RTXM228-551 |
+----------+----------------------+----------------------+
+Laser turns off for SFP+ when ifconfig ethX down
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+"ifconfig ethX down" turns off the laser for SFP+ fiber adapters.
+"ifconfig ethX up" turns on the laser.
+
Support
=======
@@ -7,6 +7,7 @@
#include <net/ip.h>
#include <linux/pci.h>
#include <linux/etherdevice.h>
+#include <linux/timecounter.h>
#include "txgbe_type.h"
@@ -29,6 +30,22 @@ struct txgbe_mac_addr {
#define TXGBE_MAC_STATE_MODIFIED 0x2
#define TXGBE_MAC_STATE_IN_USE 0x4
+/* default to trying for four seconds */
+#define TXGBE_TRY_LINK_TIMEOUT (4 * HZ)
+#define TXGBE_SFP_POLL_JIFFIES (2 * HZ) /* SFP poll every 2 seconds */
+
+/**
+ * txgbe_adapter.flag
+ **/
+#define TXGBE_FLAG_NEED_LINK_UPDATE BIT(0)
+#define TXGBE_FLAG_NEED_LINK_CONFIG BIT(1)
+
+/**
+ * txgbe_adapter.flag2
+ **/
+#define TXGBE_FLAG2_MNG_REG_ACCESS_DISABLED BIT(0)
+#define TXGBE_FLAG2_SFP_NEEDS_RESET BIT(1)
+
/* board specific private data structure */
struct txgbe_adapter {
u8 __iomem *io_addr; /* Mainly for iounmap use */
@@ -38,6 +55,8 @@ struct txgbe_adapter {
unsigned long state;
+ u32 flags;
+ u32 flags2;
/* Tx fast path data */
int num_tx_queues;
@@ -48,6 +67,11 @@ struct txgbe_adapter {
struct txgbe_hw hw;
u16 msg_enable;
+ u32 link_speed;
+ bool link_up;
+ unsigned long sfp_poll_time;
+ unsigned long link_check_timeout;
+
struct timer_list service_timer;
struct work_struct service_task;
@@ -67,6 +91,7 @@ enum txgbe_state_t {
__TXGBE_REMOVING,
__TXGBE_SERVICE_SCHED,
__TXGBE_SERVICE_INITED,
+ __TXGBE_IN_SFP_INIT,
};
/* needed by txgbe_main.c */
@@ -29,6 +29,34 @@ u32 txgbe_rd32_epcs(struct txgbe_hw *hw, u32 addr)
return data;
}
+void txgbe_wr32_ephy(struct txgbe_hw *hw, u32 addr, u32 data)
+{
+ unsigned int offset;
+
+ /* Set the LAN port indicator to offset[1] */
+ /* 1st, write the offset to IDA_ADDR register */
+ offset = TXGBE_ETHPHY_IDA_ADDR;
+ wr32(hw, offset, addr);
+
+ /* 2nd, read the data from IDA_DATA register */
+ offset = TXGBE_ETHPHY_IDA_DATA;
+ wr32(hw, offset, data);
+}
+
+void txgbe_wr32_epcs(struct txgbe_hw *hw, u32 addr, u32 data)
+{
+ unsigned int offset;
+
+ /* Set the LAN port indicator to offset[1] */
+ /* 1st, write the offset to IDA_ADDR register */
+ offset = TXGBE_XPCS_IDA_ADDR;
+ wr32(hw, offset, addr);
+
+ /* 2nd, read the data from IDA_DATA register */
+ offset = TXGBE_XPCS_IDA_DATA;
+ wr32(hw, offset, data);
+}
+
s32 txgbe_init_hw(struct txgbe_hw *hw)
{
s32 status;
@@ -1104,11 +1132,12 @@ s32 txgbe_reset_hostif(struct txgbe_hw *hw)
continue;
if (reset_cmd.hdr.cmd_or_resp.ret_status ==
- FW_CEM_RESP_STATUS_SUCCESS)
+ FW_CEM_RESP_STATUS_SUCCESS) {
status = 0;
- else
+ hw->link_status = TXGBE_LINK_STATUS_NONE;
+ } else {
status = TXGBE_ERR_HOST_INTERFACE_COMMAND;
-
+ }
break;
}
@@ -1232,6 +1261,141 @@ bool txgbe_check_mng_access(struct txgbe_hw *hw)
return true;
}
+/**
+ * txgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed in the MAC and/or PHY register and restarts link.
+ **/
+s32 txgbe_setup_mac_link_multispeed_fiber(struct txgbe_hw *hw,
+ u32 speed,
+ bool autoneg_wait_to_complete)
+{
+ u32 link_speed = TXGBE_LINK_SPEED_UNKNOWN;
+ u32 highest_link_speed = TXGBE_LINK_SPEED_UNKNOWN;
+ s32 status = 0;
+ u32 speedcnt = 0;
+ u32 i = 0;
+ bool autoneg, link_up = false;
+
+ /* Mask off requested but non-supported speeds */
+ status = TCALL(hw, mac.ops.get_link_capabilities,
+ &link_speed, &autoneg);
+ if (status != 0)
+ return status;
+
+ speed &= link_speed;
+
+ /* Try each speed one by one, highest priority first. We do this in
+ * software because 10Gb fiber doesn't support speed autonegotiation.
+ */
+ if (speed & TXGBE_LINK_SPEED_10GB_FULL) {
+ speedcnt++;
+ highest_link_speed = TXGBE_LINK_SPEED_10GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = TCALL(hw, mac.ops.check_link,
+ &link_speed, &link_up, false);
+ if (status != 0)
+ return status;
+
+ if (link_speed == TXGBE_LINK_SPEED_10GB_FULL && link_up)
+ goto out;
+
+ /* Allow module to change analog characteristics (1G->10G) */
+ msleep(40);
+
+ status = TCALL(hw, mac.ops.setup_mac_link,
+ TXGBE_LINK_SPEED_10GB_FULL,
+ autoneg_wait_to_complete);
+ if (status != 0)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ TCALL(hw, mac.ops.flap_tx_laser);
+
+ /* Wait for the controller to acquire link. Per IEEE 802.3ap,
+ * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * attempted. sapphire uses the same timing for 10g SFI.
+ */
+ for (i = 0; i < 5; i++) {
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ status = TCALL(hw, mac.ops.check_link,
+ &link_speed, &link_up, false);
+ if (status != 0)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+ }
+
+ if (speed & TXGBE_LINK_SPEED_1GB_FULL) {
+ speedcnt++;
+ if (highest_link_speed == TXGBE_LINK_SPEED_UNKNOWN)
+ highest_link_speed = TXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = TCALL(hw, mac.ops.check_link,
+ &link_speed, &link_up, false);
+ if (status != 0)
+ return status;
+
+ if (link_speed == TXGBE_LINK_SPEED_1GB_FULL && link_up)
+ goto out;
+
+ /* Allow module to change analog characteristics (10G->1G) */
+ msleep(40);
+
+ status = TCALL(hw, mac.ops.setup_mac_link,
+ TXGBE_LINK_SPEED_1GB_FULL,
+ autoneg_wait_to_complete);
+ if (status != 0)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ TCALL(hw, mac.ops.flap_tx_laser);
+
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ status = TCALL(hw, mac.ops.check_link,
+ &link_speed, &link_up, false);
+ if (status != 0)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+
+ /* We didn't get link. Configure back to the highest speed we tried,
+ * (if there was more than one). We call ourselves back with just the
+ * single highest speed that the user requested.
+ */
+ if (speedcnt > 1)
+ status = txgbe_setup_mac_link_multispeed_fiber(hw,
+ highest_link_speed,
+ autoneg_wait_to_complete);
+
+out:
+ /* Set autoneg_advertised value based on input link speed */
+ hw->phy.autoneg_advertised = 0;
+
+ if (speed & TXGBE_LINK_SPEED_10GB_FULL)
+ hw->phy.autoneg_advertised |= TXGBE_LINK_SPEED_10GB_FULL;
+
+ if (speed & TXGBE_LINK_SPEED_1GB_FULL)
+ hw->phy.autoneg_advertised |= TXGBE_LINK_SPEED_1GB_FULL;
+
+ return status;
+}
+
int txgbe_check_flash_load(struct txgbe_hw *hw, u32 check_bit)
{
u32 i = 0, reg = 0;
@@ -1255,6 +1419,34 @@ int txgbe_check_flash_load(struct txgbe_hw *hw, u32 check_bit)
return err;
}
+void txgbe_init_mac_link_ops(struct txgbe_hw *hw)
+{
+ struct txgbe_mac_info *mac = &hw->mac;
+
+ /* enable the laser control functions for SFP+ fiber
+ * and MNG not enabled
+ */
+ if (hw->phy.media_type == txgbe_media_type_fiber) {
+ mac->ops.disable_tx_laser = txgbe_disable_tx_laser_multispeed_fiber;
+ mac->ops.enable_tx_laser = txgbe_enable_tx_laser_multispeed_fiber;
+ mac->ops.flap_tx_laser = txgbe_flap_tx_laser_multispeed_fiber;
+ } else {
+ mac->ops.disable_tx_laser = NULL;
+ mac->ops.enable_tx_laser = NULL;
+ mac->ops.flap_tx_laser = NULL;
+ }
+
+ if (hw->phy.multispeed_fiber) {
+ /* Set up dual speed SFP+ support */
+ mac->ops.setup_link = txgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_mac_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ } else {
+ mac->ops.setup_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ }
+}
+
/**
* txgbe_init_phy_ops - PHY/SFP specific init
* @hw: pointer to hardware structure
@@ -1270,7 +1462,13 @@ s32 txgbe_init_phy_ops(struct txgbe_hw *hw)
txgbe_init_i2c(hw);
/* Identify the PHY or SFP module */
ret_val = TCALL(hw, phy.ops.identify);
+ if (ret_val == TXGBE_ERR_SFP_NOT_SUPPORTED)
+ goto init_phy_ops_out;
+ /* Setup function pointers based on detected SFP module and speeds */
+ txgbe_init_mac_link_ops(hw);
+
+init_phy_ops_out:
return ret_val;
}
@@ -1317,6 +1515,9 @@ s32 txgbe_init_ops(struct txgbe_hw *hw)
mac->ops.set_vmdq_san_mac = txgbe_set_vmdq_san_mac;
mac->ops.init_uta_tables = txgbe_init_uta_tables;
+ /* Link */
+ mac->ops.get_link_capabilities = txgbe_get_link_capabilities;
+ mac->ops.check_link = txgbe_check_mac_link;
mac->num_rar_entries = TXGBE_SP_RAR_ENTRIES;
mac->max_rx_queues = TXGBE_SP_MAX_RX_QUEUES;
mac->max_tx_queues = TXGBE_SP_MAX_TX_QUEUES;
@@ -1337,6 +1538,124 @@ s32 txgbe_init_ops(struct txgbe_hw *hw)
return 0;
}
+/**
+ * txgbe_get_link_capabilities - Determines link capabilities
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @autoneg: true when autoneg or autotry is enabled
+ **/
+s32 txgbe_get_link_capabilities(struct txgbe_hw *hw,
+ u32 *speed,
+ bool *autoneg)
+{
+ s32 status = 0;
+ u32 sr_pcs_ctl, sr_pma_mmd_ctl1, sr_an_mmd_ctl;
+ u32 sr_an_mmd_adv_reg2;
+
+ /* Check if 1G SFP module. */
+ if (hw->phy.sfp_type == txgbe_sfp_type_1g_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_cu_core1 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_lx_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_lx_core1 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_sx_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_sx_core1) {
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = false;
+ } else if (hw->phy.multispeed_fiber) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL |
+ TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = true;
+ }
+ /* SFP */
+ else if (hw->phy.media_type == txgbe_media_type_fiber) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ }
+ /* SGMII */
+ else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_SGMII) {
+ *speed = TXGBE_LINK_SPEED_1GB_FULL |
+ TXGBE_LINK_SPEED_100_FULL |
+ TXGBE_LINK_SPEED_10_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_1000BASE_T |
+ TXGBE_PHYSICAL_LAYER_100BASE_TX;
+ /* MAC XAUI */
+ } else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_XAUI) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ /* MAC SGMII */
+ } else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_SGMII) {
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ } else { /* KR KX KX4 */
+ /* Determine link capabilities based on the stored value,
+ * which represents EEPROM defaults. If value has not
+ * been stored, use the current register values.
+ */
+ if (hw->mac.orig_link_settings_stored) {
+ sr_pcs_ctl = hw->mac.orig_sr_pcs_ctl2;
+ sr_pma_mmd_ctl1 = hw->mac.orig_sr_pma_mmd_ctl1;
+ sr_an_mmd_ctl = hw->mac.orig_sr_an_mmd_ctl;
+ sr_an_mmd_adv_reg2 = hw->mac.orig_sr_an_mmd_adv_reg2;
+ } else {
+ sr_pcs_ctl = txgbe_rd32_epcs(hw, TXGBE_SR_PCS_CTL2);
+ sr_pma_mmd_ctl1 = txgbe_rd32_epcs(hw,
+ TXGBE_SR_PMA_MMD_CTL1);
+ sr_an_mmd_ctl = txgbe_rd32_epcs(hw,
+ TXGBE_SR_AN_MMD_CTL);
+ sr_an_mmd_adv_reg2 = txgbe_rd32_epcs(hw,
+ TXGBE_SR_AN_MMD_ADV_REG2);
+ }
+
+ if ((sr_pcs_ctl & TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK) ==
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X &&
+ (sr_pma_mmd_ctl1 & TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_MASK) ==
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_1G &&
+ (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) == 0) {
+ /* 1G or KX - no backplane auto-negotiation */
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ } else if ((sr_pcs_ctl & TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK) ==
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X &&
+ (sr_pma_mmd_ctl1 & TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_MASK) ==
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_10G &&
+ (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) == 0) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ } else if ((sr_pcs_ctl & TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK) ==
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_R &&
+ (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) == 0) {
+ /* 10 GbE serial link (KR -no backplane auto-negotiation) */
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KR;
+ } else if (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) {
+ /* KX/KX4/KR backplane auto-negotiation enable */
+ *speed = TXGBE_LINK_SPEED_UNKNOWN;
+ if (sr_an_mmd_adv_reg2 & TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KR)
+ *speed |= TXGBE_LINK_SPEED_10GB_FULL;
+ if (sr_an_mmd_adv_reg2 & TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX4)
+ *speed |= TXGBE_LINK_SPEED_10GB_FULL;
+ if (sr_an_mmd_adv_reg2 & TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX)
+ *speed |= TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = true;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KR |
+ TXGBE_PHYSICAL_LAYER_10GBASE_KX4 |
+ TXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ } else {
+ status = TXGBE_ERR_LINK_SETUP;
+ goto out;
+ }
+ }
+
+out:
+ return status;
+}
+
/**
* txgbe_get_media_type - Get media type
* @hw: pointer to hardware structure
@@ -1376,12 +1695,949 @@ enum txgbe_media_type txgbe_get_media_type(struct txgbe_hw *hw)
return media_type;
}
+/**
+ * txgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser
+ * @hw: pointer to hardware structure
+ *
+ * The base drivers may require better control over SFP+ module
+ * PHY states. This includes selectively shutting down the Tx
+ * laser on the PHY, effectively halting physical link.
+ **/
+s32 txgbe_disable_tx_laser_multispeed_fiber(struct txgbe_hw *hw)
+{
+ u32 esdp_reg = rd32(hw, TXGBE_GPIO_DR);
+
+ if (!(hw->phy.media_type == txgbe_media_type_fiber))
+ return 0;
+ /* Blocked by MNG FW so bail */
+ txgbe_check_reset_blocked(hw);
+
+ /* Disable Tx laser; allow 100us to go dark per spec */
+ esdp_reg |= TXGBE_GPIO_DR_1 | TXGBE_GPIO_DR_0;
+ wr32(hw, TXGBE_GPIO_DR, esdp_reg);
+ TXGBE_WRITE_FLUSH(hw);
+ usleep_range(100, 200);
+
+ return 0;
+}
+
+/**
+ * txgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser
+ * @hw: pointer to hardware structure
+ *
+ * The base drivers may require better control over SFP+ module
+ * PHY states. This includes selectively turning on the Tx
+ * laser on the PHY, effectively starting physical link.
+ **/
+s32 txgbe_enable_tx_laser_multispeed_fiber(struct txgbe_hw *hw)
+{
+ if (!(TCALL(hw, mac.ops.get_media_type) == txgbe_media_type_fiber))
+ return 0;
+
+ /* Enable Tx laser; allow 100ms to light up */
+ wr32m(hw, TXGBE_GPIO_DR,
+ TXGBE_GPIO_DR_0 | TXGBE_GPIO_DR_1, 0);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(100);
+
+ return 0;
+}
+
+/**
+ * txgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser
+ * @hw: pointer to hardware structure
+ *
+ * When the driver changes the link speeds that it can support,
+ * it sets autotry_restart to true to indicate that we need to
+ * initiate a new autotry session with the link partner. To do
+ * so, we set the speed then disable and re-enable the Tx laser, to
+ * alert the link partner that it also needs to restart autotry on its
+ * end. This is consistent with true clause 37 autoneg, which also
+ * involves a loss of signal.
+ **/
+s32 txgbe_flap_tx_laser_multispeed_fiber(struct txgbe_hw *hw)
+{
+ /* Blocked by MNG FW so bail */
+ txgbe_check_reset_blocked(hw);
+
+ if (hw->mac.autotry_restart) {
+ txgbe_disable_tx_laser_multispeed_fiber(hw);
+ txgbe_enable_tx_laser_multispeed_fiber(hw);
+ hw->mac.autotry_restart = false;
+ }
+
+ return 0;
+}
+
+/**
+ * txgbe_set_hard_rate_select_speed - Set module link speed
+ * @hw: pointer to hardware structure
+ * @speed: link speed to set
+ *
+ * Set module link speed via RS0/RS1 rate select pins.
+ */
+s32 txgbe_set_hard_rate_select_speed(struct txgbe_hw *hw,
+ u32 speed)
+{
+ u32 esdp_reg = rd32(hw, TXGBE_GPIO_DR);
+
+ switch (speed) {
+ case TXGBE_LINK_SPEED_10GB_FULL:
+ esdp_reg |= TXGBE_GPIO_DR_5 | TXGBE_GPIO_DR_4;
+ break;
+ case TXGBE_LINK_SPEED_1GB_FULL:
+ esdp_reg &= ~(TXGBE_GPIO_DR_5 | TXGBE_GPIO_DR_4);
+ break;
+ default:
+ txgbe_dbg(hw, "Invalid fixed module speed\n");
+ return 0;
+ }
+
+ wr32(hw, TXGBE_GPIO_DDR,
+ TXGBE_GPIO_DDR_5 | TXGBE_GPIO_DDR_4 |
+ TXGBE_GPIO_DDR_1 | TXGBE_GPIO_DDR_0);
+
+ wr32(hw, TXGBE_GPIO_DR, esdp_reg);
+
+ TXGBE_WRITE_FLUSH(hw);
+
+ return 0;
+}
+
+static s32 txgbe_set_sgmii_an37_ability(struct txgbe_hw *hw)
+{
+ u32 value;
+
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0x3002);
+ /* for sgmii + external phy, set to 0x0105 (phy sgmii mode) */
+ /* for sgmii direct link, set to 0x010c (mac sgmii mode) */
+ if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_SGMII ||
+ hw->phy.media_type == txgbe_media_type_fiber) {
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x010c);
+ } else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_SGMII ||
+ (hw->subsystem_device_id & 0xF0) == TXGBE_ID_XAUI) {
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x0105);
+ }
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_DIGI_CTL, 0x0200);
+ value = txgbe_rd32_epcs(hw, TXGBE_SR_MII_MMD_CTL);
+ value = (value & ~0x1200) | (0x1 << 12) | (0x1 << 9);
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_CTL, value);
+ return 0;
+}
+
+s32 txgbe_set_link_to_kr(struct txgbe_hw *hw, bool autoneg)
+{
+ struct txgbe_adapter *adapter = container_of(hw, struct txgbe_adapter, hw);
+ s32 status = 0;
+ u32 i;
+
+ /* 1. Wait xpcs power-up good */
+ for (i = 0; i < TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD)
+ break;
+ msleep(20);
+ }
+ if (i == TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME) {
+ status = TXGBE_ERR_XPCS_POWER_UP_FAILED;
+ goto out;
+ }
+ dev_info(&adapter->pdev->dev, "It is set to kr.\n");
+
+ txgbe_wr32_epcs(hw, 0x78001, 0x7);
+
+ /* 2. Disable xpcs AN-73 */
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x3000);
+ txgbe_wr32_epcs(hw, TXGBE_VR_AN_KR_MODE_CL, 0x1);
+
+ /* 3. Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL3 Register */
+ /* Bit[10:0](MPLLA_BANDWIDTH) = 11'd123 (default: 11'd16) */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3,
+ TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_10GBASER_KR);
+
+ /* 4. Set VR_XS_PMA_Gen5_12G_MISC_CTRL0 Register */
+ /* Bit[12:8](RX_VREF_CTRL) = 5'hF (default: 5'h11) */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+
+ /* 5. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register */
+ /* Bit[15:8](VGA1/2_GAIN_0) = 8'h77,
+ * Bit[7:5](CTLE_POLE_0) = 3'h2
+ * Bit[4:0](CTLE_BOOST_0) = 4'hA
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, 0x774A);
+
+ /* 6. Set VR_MII_Gen5_12G_RX_GENCTRL3 Register */
+ /* Bit[2:0](LOS_TRSHLD_0) = 3'h4 (default: 3) */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, 0x0004);
+ /* 7. Initialize the mode by setting VR XS or PCS MMD Digital */
+ /* Control1 Register Bit[15](VR_RST) */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+ /* wait phy initialization done */
+ for (i = 0; i < TXGBE_PHY_INIT_DONE_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw,
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST) == 0)
+ break;
+ msleep(100);
+ }
+ if (i == TXGBE_PHY_INIT_DONE_POLLING_TIME) {
+ status = TXGBE_ERR_PHY_INIT_NOT_DONE;
+ goto out;
+ }
+
+out:
+ return status;
+}
+
+s32 txgbe_set_link_to_kx4(struct txgbe_hw *hw, bool autoneg)
+{
+ struct txgbe_adapter *adapter = container_of(hw, struct txgbe_adapter, hw);
+ s32 status = 0;
+ u32 value;
+ u32 i;
+
+ /* check link status, if already set, skip setting it again */
+ if (hw->link_status == TXGBE_LINK_STATUS_KX4)
+ goto out;
+
+ dev_info(&adapter->pdev->dev, "It is set to kx4.\n");
+
+ /* 1. Wait xpcs power-up good */
+ for (i = 0; i < TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD)
+ break;
+ msleep(20);
+ }
+ if (i == TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME) {
+ status = TXGBE_ERR_XPCS_POWER_UP_FAILED;
+ goto out;
+ }
+
+ wr32m(hw, TXGBE_MAC_TX_CFG, TXGBE_MAC_TX_CFG_TE, ~TXGBE_MAC_TX_CFG_TE);
+
+ /* 2. Disable xpcs AN-73 */
+ if (!autoneg)
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x0);
+ else
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x3000);
+
+ /* Disable PHY MPLLA for eth mode change(after ECO) */
+ txgbe_wr32_ephy(hw, 0x4, 0x250A);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(20);
+
+ /* Set the eth change_mode bit first in mis_rst register
+ * for corresponding LAN port
+ */
+ if (hw->bus.lan_id == 0)
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN0_CHG_ETH_MODE);
+ else
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN1_CHG_ETH_MODE);
+
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b01
+ * PCS_TYPE_SEL: non KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2,
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X);
+ /* Set SR PMA MMD Control1 Register Bit[13] = 1'b1 SS13: 10G speed */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1,
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_10G);
+
+ value = (0xf5f0 & ~0x7F0) | (0x5 << 8) | (0x7 << 5) | 0xF0;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+
+ if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_XAUI)
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+ else
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0x4F00);
+
+ for (i = 0; i < 4; i++) {
+ if (i == 0)
+ value = (0x45 & ~0xFFFF) | (0x7 << 12) |
+ (0x7 << 8) | 0x6;
+ else
+ value = (0xff06 & ~0xFFFF) | (0x7 << 12) |
+ (0x7 << 8) | 0x6;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0 + i, value);
+ }
+
+ value = 0x0 & ~0x7777;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0);
+
+ value = (0x6db & ~0xFFF) | (0x1 << 9) | (0x1 << 6) | (0x1 << 3) | 0x1;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, value);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA */
+ /* Control 0 Register Bit[7:0] = 8'd40 MPLLA_MULTIPLIER */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0,
+ TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_OTHER);
+ /* Set VR XS, PMA or MII Synopsys Enterprise Gen5 12G PHY MPLLA */
+ /* Control 3 Register Bit[10:0] = 11'd86 MPLLA_BANDWIDTH */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3,
+ TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 0 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_0 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 1 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD1, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 2 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_2 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD2, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 3 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_3 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD3, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Reference 0 Register Bit[5:0] = 6'd34 VCO_REF_LD_0/1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Reference 1 Register Bit[5:0] = 6'd34 VCO_REF_LD_2/3 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF1, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY AFE-DFE */
+ /* Enable Register Bit[7:0] = 8'd0 AFE_EN_0/3_1, DFE_EN_0/3_1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, 0x0);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx */
+ /* Equalization Control 4 Register Bit[3:0] = 4'd0 CONT_ADAPT_0/3_1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, 0x00F0);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx Rate */
+ /* Control Register Bit[14:12], Bit[10:8], Bit[6:4], Bit[2:0],
+ * all rates to 3'b010 TX0/1/2/3_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx Rate */
+ /* Control Register Bit[13:12], Bit[9:8], Bit[5:4], Bit[1:0],
+ * all rates to 2'b10 RX0/1/2/3_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx General */
+ /* Control 2 Register Bit[15:8] = 2'b01 TX0/1/2/3_WIDTH: 10bits */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2, 0x5500);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx General */
+ /* Control 2 Register Bit[15:8] = 2'b01 RX0/1/2/3_WIDTH: 10bits */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2, 0x5500);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 2 Register Bit[10:8] = 3'b010
+ * MPLLA_DIV16P5_CLK_EN=0, MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2,
+ TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_10);
+
+ txgbe_wr32_epcs(hw, 0x1f0000, 0x0);
+ txgbe_wr32_epcs(hw, 0x1f8001, 0x0);
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_DIGI_CTL, 0x0);
+
+ /* 10. Initialize the mode by setting VR XS or PCS MMD Digital Control1
+ * Register Bit[15](VR_RST)
+ */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+
+ /* wait phy initialization done */
+ for (i = 0; i < TXGBE_PHY_INIT_DONE_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST) == 0)
+ break;
+ msleep(100);
+ }
+
+ /* if success, set link status */
+ hw->link_status = TXGBE_LINK_STATUS_KX4;
+
+ if (i == TXGBE_PHY_INIT_DONE_POLLING_TIME) {
+ status = TXGBE_ERR_PHY_INIT_NOT_DONE;
+ goto out;
+ }
+
+out:
+ return status;
+}
+
+s32 txgbe_set_link_to_kx(struct txgbe_hw *hw, u32 speed, bool autoneg)
+{
+ struct txgbe_adapter *adapter = container_of(hw, struct txgbe_adapter, hw);
+ s32 status = 0;
+ u32 wdata = 0;
+ u32 value;
+ u32 i;
+
+ /* check link status, if already set, skip setting it again */
+ if (hw->link_status == TXGBE_LINK_STATUS_KX)
+ goto out;
+
+ dev_info(&adapter->pdev->dev, "It is set to kx. speed =0x%x\n", speed);
+
+ /* 1. Wait xpcs power-up good */
+ for (i = 0; i < TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD)
+ break;
+ msleep(20);
+ }
+ if (i == TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME) {
+ status = TXGBE_ERR_XPCS_POWER_UP_FAILED;
+ goto out;
+ }
+
+ wr32m(hw, TXGBE_MAC_TX_CFG, TXGBE_MAC_TX_CFG_TE, ~TXGBE_MAC_TX_CFG_TE);
+
+ /* 2. Disable xpcs AN-73 */
+ if (!autoneg)
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x0);
+ else
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x3000);
+
+ /* Disable PHY MPLLA for eth mode change(after ECO) */
+ txgbe_wr32_ephy(hw, 0x4, 0x240A);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(20);
+
+ /* Set the eth change_mode bit first in mis_rst register */
+ /* for corresponding LAN port */
+ if (hw->bus.lan_id == 0)
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN0_CHG_ETH_MODE);
+ else
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN1_CHG_ETH_MODE);
+
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b01
+ * PCS_TYPE_SEL: non KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2,
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X);
+
+ /* Set SR PMA MMD Control1 Register Bit[13] = 1'b0 SS13: 1G speed */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1,
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_1G);
+
+ /* Set SR MII MMD Control Register to corresponding speed: {Bit[6],
+ * Bit[13]}=[2'b00,2'b01,2'b10]->[10M,100M,1G]
+ */
+ if (speed == TXGBE_LINK_SPEED_100_FULL)
+ wdata = 0x2100;
+ else if (speed == TXGBE_LINK_SPEED_1GB_FULL)
+ wdata = 0x0140;
+ else if (speed == TXGBE_LINK_SPEED_10_FULL)
+ wdata = 0x0100;
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_CTL, wdata);
+
+ value = (0xf5f0 & ~0x710) | (0x5 << 8) | 0x10;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+
+ for (i = 0; i < 4; i++) {
+ if (i)
+ value = 0xff06;
+ else
+ value = (0x45 & ~0xFFFF) | (0x7 << 12) |
+ (0x7 << 8) | 0x6;
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0 + i, value);
+ }
+
+ value = 0x0 & ~0x7;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0);
+
+ value = (0x6db & ~0x7) | 0x4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, value);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 0 Register Bit[7:0] = 8'd32 MPLLA_MULTIPLIER
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0,
+ TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_1GBASEX_KX);
+
+ /* Set VR XS, PMA or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 3 Register Bit[10:0] = 11'd70 MPLLA_BANDWIDTH
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3,
+ TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_1GBASEX_KX);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Load 0 Register Bit[12:0] = 13'd1344 VCO_LD_VAL_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0,
+ TXGBE_PHY_VCO_CAL_LD0_1GBASEX_KX);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD1, 0x549);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD2, 0x549);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD3, 0x549);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Reference 0 Register Bit[5:0] = 6'd42 VCO_REF_LD_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0,
+ TXGBE_PHY_VCO_CAL_REF0_LD0_1GBASEX_KX);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF1, 0x2929);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY AFE-DFE
+ * Enable Register Bit[4], Bit[0] = 1'b0 AFE_EN_0, DFE_EN_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, 0x0);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx
+ * Equalization Control 4 Register Bit[0] = 1'b0 CONT_ADAPT_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, 0x0010);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx Rate
+ * Control Register Bit[2:0] = 3'b011 TX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL,
+ TXGBE_PHY_TX_RATE_CTL_TX0_RATE_1GBASEX_KX);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx Rate
+ * Control Register Bit[2:0] = 3'b011 RX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL,
+ TXGBE_PHY_RX_RATE_CTL_RX0_RATE_1GBASEX_KX);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx General
+ * Control 2 Register Bit[9:8] = 2'b01 TX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2,
+ TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx General
+ * Control 2 Register Bit[9:8] = 2'b01 RX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2,
+ TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 2 Register Bit[10:8] = 3'b010 MPLLA_DIV16P5_CLK_EN=0,
+ * MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2,
+ TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_10);
+
+ /* VR MII MMD AN Control Register Bit[8] = 1'b1 MII_CTRL */
+ /* Set to 8bit MII (required in 10M/100M SGMII) */
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x0100);
+
+ /* 10. Initialize the mode by setting VR XS or PCS MMD Digital Control1
+ * Register Bit[15](VR_RST)
+ */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+ /* wait phy initialization done */
+ for (i = 0; i < TXGBE_PHY_INIT_DONE_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST) == 0)
+ break;
+ msleep(100);
+ }
+
+ /* if success, set link status */
+ hw->link_status = TXGBE_LINK_STATUS_KX;
+
+ if (i == TXGBE_PHY_INIT_DONE_POLLING_TIME) {
+ status = TXGBE_ERR_PHY_INIT_NOT_DONE;
+ goto out;
+ }
+
+ dev_info(&adapter->pdev->dev, "Set KX TX_EQ MAIN:24 PRE:4 POST:16\n");
+ /* 5. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL0 Register
+ * Bit[13:8](TX_EQ_MAIN) = 6'd30, Bit[5:0](TX_EQ_PRE) = 6'd4
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0);
+ value = (value & ~0x3F3F) | (24 << 8) | 4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0, value);
+ /* 6. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL1 Register
+ * Bit[6](TX_EQ_OVR_RIDE) = 1'b1, Bit[5:0](TX_EQ_POST) = 6'd36
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1);
+ value = (value & ~0x7F) | 16 | (1 << 6);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1, value);
+
+out:
+ return status;
+}
+
+static s32 txgbe_set_link_to_sfi(struct txgbe_hw *hw, u32 speed)
+{
+ u32 i;
+ s32 status = 0;
+ u32 value = 0;
+
+ /* Set the module link speed */
+ TCALL(hw, mac.ops.set_rate_select_speed, speed);
+
+ /* 1. Wait xpcs power-up good */
+ for (i = 0; i < TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD)
+ break;
+ msleep(20);
+ }
+ if (i == TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME) {
+ status = TXGBE_ERR_XPCS_POWER_UP_FAILED;
+ goto out;
+ }
+
+ wr32m(hw, TXGBE_MAC_TX_CFG, TXGBE_MAC_TX_CFG_TE, ~TXGBE_MAC_TX_CFG_TE);
+
+ /* 2. Disable xpcs AN-73 */
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x0);
+
+ /* Disable PHY MPLLA for eth mode change(after ECO) */
+ txgbe_wr32_ephy(hw, 0x4, 0x243A);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(20);
+ /* Set the eth change_mode bit first in mis_rst register
+ * for corresponding LAN port
+ */
+ if (hw->bus.lan_id == 0)
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN0_CHG_ETH_MODE);
+ else
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN1_CHG_ETH_MODE);
+
+ if (speed == TXGBE_LINK_SPEED_10GB_FULL) {
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b00
+ * PCS_TYPE_SEL: KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2, 0);
+ value = txgbe_rd32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1);
+ value = value | 0x2000;
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1, value);
+ /* Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL0 Register Bit[7:0] = 8'd33
+ * MPLLA_MULTIPLIER
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0, 0x0021);
+ /* 3. Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL3 Register
+ * Bit[10:0](MPLLA_BANDWIDTH) = 11'd0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3, 0);
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_GENCTRL1);
+ value = (value & ~0x700) | 0x500;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+ /* 4.Set VR_XS_PMA_Gen5_12G_MISC_CTRL0 Register
+ * Bit[12:8](RX_VREF_CTRL) = 5'hF
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+ /* Set VR_XS_PMA_Gen5_12G_VCO_CAL_LD0 Register
+ * Bit[12:0] = 13'd1353 VCO_LD_VAL_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0, 0x0549);
+ /* Set VR_XS_PMA_Gen5_12G_VCO_CAL_REF0 Register Bit[5:0] = 6'd41
+ * VCO_REF_LD_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0, 0x0029);
+ /* Set VR_XS_PMA_Gen5_12G_TX_RATE_CTRL Register
+ * Bit[2:0] = 3'b000 TX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL, 0);
+ /* Set VR_XS_PMA_Gen5_12G_RX_RATE_CTRL Register
+ * Bit[2:0] = 3'b000 RX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL, 0);
+ /* Set VR_XS_PMA_Gen5_12G_TX_GENCTRL2 Register Bit[9:8] = 2'b11
+ * TX0_WIDTH: 20bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2, 0x0300);
+ /* Set VR_XS_PMA_Gen5_12G_RX_GENCTRL2 Register Bit[9:8] = 2'b11
+ * RX0_WIDTH: 20bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2, 0x0300);
+ /* Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL2 Register
+ * Bit[10:8] = 3'b110 MPLLA_DIV16P5_CLK_EN=1,
+ * MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2, 0x0600);
+
+ if (hw->phy.sfp_type == txgbe_sfp_type_da_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_da_cu_core1) {
+ /* 7. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register
+ * Bit[15:8](VGA1/2_GAIN_0) = 8'h77, Bit[7:5]
+ * (CTLE_POLE_0) = 3'h2, Bit[4:0](CTLE_BOOST_0) = 4'hF
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, 0x774F);
+ } else {
+ /* 7. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register
+ * Bit[15:8] (VGA1/2_GAIN_0) = 8'h00,
+ * Bit[7:5](CTLE_POLE_0) = 3'h2,
+ * Bit[4:0](CTLE_BOOST_0) = 4'hA
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0);
+ value = (value & ~0xFFFF) | (2 << 5) | 0x05;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, value);
+ }
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0);
+ value &= ~0x7;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+
+ if (hw->phy.sfp_type == txgbe_sfp_type_da_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_da_cu_core1) {
+ /* 8. Set VR_XS_PMA_Gen5_12G_DFE_TAP_CTRL0 Register
+ * Bit[7:0](DFE_TAP1_0) = 8'd20
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0014);
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE);
+ value = (value & ~0x11) | 0x11;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, value);
+ } else {
+ /* 8. Set VR_XS_PMA_Gen5_12G_DFE_TAP_CTRL0 Register
+ * Bit[7:0](DFE_TAP1_0) = 8'd20
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0xBE);
+ /* 9. Set VR_MII_Gen5_12G_AFE_DFE_EN_CTRL Register
+ * Bit[4](DFE_EN_0) = 1'b0, Bit[0](AFE_EN_0) = 1'b0
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE);
+ value = (value & ~0x11) | 0x0;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, value);
+ }
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_CTL);
+ value = value & ~0x1;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, value);
+ } else {
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b00
+ * PCS_TYPE_SEL: KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2, 0x1);
+ /* Set SR PMA MMD Control1 Register Bit[13] = 1'b0
+ * SS13: 1G speed
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1, 0x0000);
+ /* Set SR MII MMD Control Register to corresponding speed: */
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_CTL, 0x0140);
+
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_GENCTRL1);
+ value = (value & ~0x710) | 0x500;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+ /* 4. Set VR_XS_PMA_Gen5_12G_MISC_CTRL0 Register
+ * Bit[12:8](RX_VREF_CTRL) = 5'hF
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+ /* 5. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL0 Register
+ * Bit[13:8](TX_EQ_MAIN) = 6'd30, Bit[5:0](TX_EQ_PRE) = 6'd4
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0);
+ value = (value & ~0x3F3F) | (24 << 8) | 4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0, value);
+ /* 6. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL1 Register
+ * Bit[6](TX_EQ_OVR_RIDE) = 1'b1, Bit[5:0](TX_EQ_POST) = 6'd36
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1);
+ value = (value & ~0x7F) | 16 | (1 << 6);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1, value);
+ if (hw->phy.sfp_type == txgbe_sfp_type_da_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_da_cu_core1) {
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, 0x774F);
+ } else {
+ /* 7. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register
+ * Bit[15:8] (VGA1/2_GAIN_0) = 8'h00,
+ * Bit[7:5](CTLE_POLE_0) = 3'h2,
+ * Bit[4:0](CTLE_BOOST_0) = 4'hA
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0);
+ value = (value & ~0xFFFF) | 0x7706;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, value);
+ }
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0);
+ value = (value & ~0x7) | 0x0;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+ /* 8. Set VR_XS_PMA_Gen5_12G_DFE_TAP_CTRL0 Register
+ * Bit[7:0](DFE_TAP1_0) = 8'd00
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0);
+ /* Set VR_XS_PMA_Gen5_12G_RX_GENCTRL3 Register
+ * Bit[2:0] LOS_TRSHLD_0 = 4
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3);
+ value = (value & ~0x7) | 0x4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, value);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY
+ * MPLLA Control 0 Register Bit[7:0] = 8'd32 MPLLA_MULTIPLIER
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0, 0x0020);
+ /* Set VR XS, PMA or MII Synopsys Enterprise Gen5 12G PHY MPLLA
+ * Control 3 Register Bit[10:0] = 11'd70 MPLLA_BANDWIDTH
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3, 0x0046);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Load 0 Register
+ * Bit[12:0] = 13'd1344 VCO_LD_VAL_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0, 0x0540);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Reference 0 Register
+ * Bit[5:0] = 6'd42 VCO_REF_LD_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0, 0x002A);
+ /* Set VR XS, PMA, MII Synopsys Enterprise Gen5 12G PHY AFE-DFE
+ * Enable Register Bit[4], Bit[0] = 1'b0 AFE_EN_0, DFE_EN_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, 0x0);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx
+ * Equalization Control 4 Register Bit[0] = 1'b0 CONT_ADAPT_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, 0x0010);
+ /* Set VR XS, PMA, MII Synopsys Enterprise Gen5 12G PHY Tx Rate
+ * Control Register Bit[2:0] = 3'b011 TX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL, 0x0003);
+ /* Set VR XS, PMA, MII Synopsys Enterprise Gen5 12G PHY Rx Rate
+ * Control Register Bit[2:0] = 3'b011
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL, 0x0003);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY
+ * Tx General Control 2 Register
+ * Bit[9:8] = 2'b01 TX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2, 0x0100);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY
+ * Rx General Control 2 Register
+ * Bit[9:8] = 2'b01 RX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2, 0x0100);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA
+ * Control 2 Register Bit[10:8] = 3'b010 MPLLA_DIV16P5_CLK_EN=0,
+ * MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2, 0x0200);
+ /* VR MII MMD AN Control Register Bit[8] = 1'b1 MII_CTRL */
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x0100);
+ }
+ /* 10. Initialize the mode by setting VR XS or PCS MMD Digital Control1
+ * Register Bit[15](VR_RST)
+ */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+ /* wait phy initialization done */
+ for (i = 0; i < TXGBE_PHY_INIT_DONE_POLLING_TIME; i++) {
+ if ((txgbe_rd32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1) &
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST) == 0)
+ break;
+ msleep(100);
+ }
+ if (i == TXGBE_PHY_INIT_DONE_POLLING_TIME) {
+ status = TXGBE_ERR_PHY_INIT_NOT_DONE;
+ goto out;
+ }
+
+out:
+ return status;
+}
+
+/**
+ * txgbe_setup_mac_link - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed.
+ **/
+s32 txgbe_setup_mac_link(struct txgbe_hw *hw,
+ u32 speed,
+ bool __maybe_unused autoneg_wait_to_complete)
+{
+ u32 link_capabilities = TXGBE_LINK_SPEED_UNKNOWN;
+ u32 link_speed = TXGBE_LINK_SPEED_UNKNOWN;
+ u16 sub_dev_id = hw->subsystem_device_id;
+ bool autoneg = false;
+ bool link_up = false;
+ s32 status = 0;
+
+ /* Check to see if speed passed in is supported. */
+ status = TCALL(hw, mac.ops.get_link_capabilities,
+ &link_capabilities, &autoneg);
+ if (status)
+ goto out;
+
+ speed &= link_capabilities;
+
+ if (speed == TXGBE_LINK_SPEED_UNKNOWN) {
+ status = TXGBE_ERR_LINK_SETUP;
+ goto out;
+ }
+
+ if (!(((sub_dev_id & TXGBE_DEV_MASK) == TXGBE_ID_KR_KX_KX4) ||
+ ((sub_dev_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_XAUI) ||
+ ((sub_dev_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_SGMII))) {
+ status = TCALL(hw, mac.ops.check_link,
+ &link_speed, &link_up, false);
+ if (status != 0)
+ goto out;
+ if (link_speed == speed && link_up)
+ goto out;
+ }
+
+ if ((hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_KR_KX_KX4) {
+ if (!autoneg) {
+ switch (hw->phy.link_mode) {
+ case TXGBE_PHYSICAL_LAYER_10GBASE_KR:
+ txgbe_set_link_to_kr(hw, autoneg);
+ break;
+ case TXGBE_PHYSICAL_LAYER_10GBASE_KX4:
+ txgbe_set_link_to_kx4(hw, autoneg);
+ break;
+ case TXGBE_PHYSICAL_LAYER_1000BASE_KX:
+ txgbe_set_link_to_kx(hw, speed, autoneg);
+ break;
+ default:
+ status = TXGBE_ERR_PHY;
+ goto out;
+ }
+ } else {
+ txgbe_set_link_to_kr(hw, autoneg);
+ }
+ } else if ((hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_XAUI ||
+ (hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_XAUI ||
+ (hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_SGMII ||
+ (hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_SGMII) {
+ if (speed == TXGBE_LINK_SPEED_10GB_FULL) {
+ txgbe_set_link_to_kx4(hw, 0);
+ } else {
+ txgbe_set_link_to_kx(hw, speed, 0);
+ txgbe_set_sgmii_an37_ability(hw);
+ }
+ } else if (hw->phy.media_type == txgbe_media_type_fiber) {
+ txgbe_set_link_to_sfi(hw, speed);
+ if (speed == TXGBE_LINK_SPEED_1GB_FULL)
+ txgbe_set_sgmii_an37_ability(hw);
+ }
+
+out:
+ return status;
+}
+
int txgbe_reset_misc(struct txgbe_hw *hw)
{
+ u32 value;
int i;
txgbe_init_i2c(hw);
+ value = txgbe_rd32_epcs(hw, TXGBE_SR_PCS_CTL2);
+ if ((value & 0x3) != TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X)
+ hw->link_status = TXGBE_LINK_STATUS_NONE;
+
/* receive packets that size > 2048 */
wr32m(hw, TXGBE_MAC_RX_CFG,
TXGBE_MAC_RX_CFG_JE, TXGBE_MAC_RX_CFG_JE);
@@ -1903,3 +3159,55 @@ s32 txgbe_validate_eeprom_checksum(struct txgbe_hw *hw,
return status;
}
+
+/**
+ * txgbe_check_mac_link - Determine link and speed status
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @link_up: true when link is up
+ * @link_up_wait_to_complete: bool used to wait for link up or not
+ *
+ * Reads the links register to determine if link is up and the current speed
+ **/
+s32 txgbe_check_mac_link(struct txgbe_hw *hw, u32 *speed,
+ bool *link_up, bool link_up_wait_to_complete)
+{
+ u32 links_reg = 0;
+ u32 i;
+
+ if (link_up_wait_to_complete) {
+ for (i = 0; i < TXGBE_LINK_UP_TIME; i++) {
+ links_reg = rd32(hw, TXGBE_CFG_PORT_ST);
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_UP) {
+ *link_up = true;
+ break;
+ }
+ *link_up = false;
+ msleep(100);
+ }
+ } else {
+ links_reg = rd32(hw, TXGBE_CFG_PORT_ST);
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_UP)
+ *link_up = true;
+ else
+ *link_up = false;
+ }
+
+ if (*link_up) {
+ if ((links_reg & TXGBE_CFG_PORT_ST_LINK_10G) ==
+ TXGBE_CFG_PORT_ST_LINK_10G)
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ else if ((links_reg & TXGBE_CFG_PORT_ST_LINK_1G) ==
+ TXGBE_CFG_PORT_ST_LINK_1G)
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ else if ((links_reg & TXGBE_CFG_PORT_ST_LINK_100M) ==
+ TXGBE_CFG_PORT_ST_LINK_100M)
+ *speed = TXGBE_LINK_SPEED_100_FULL;
+ else
+ *speed = TXGBE_LINK_SPEED_10_FULL;
+ } else {
+ *speed = TXGBE_LINK_SPEED_UNKNOWN;
+ }
+
+ return 0;
+}
@@ -56,9 +56,23 @@ bool txgbe_check_mng_access(struct txgbe_hw *hw);
s32 txgbe_init_thermal_sensor_thresh(struct txgbe_hw *hw);
s32 txgbe_disable_rx(struct txgbe_hw *hw);
+s32 txgbe_setup_mac_link_multispeed_fiber(struct txgbe_hw *hw,
+ u32 speed,
+ bool autoneg_wait_to_complete);
int txgbe_check_flash_load(struct txgbe_hw *hw, u32 check_bit);
+s32 txgbe_get_link_capabilities(struct txgbe_hw *hw,
+ u32 *speed, bool *autoneg);
enum txgbe_media_type txgbe_get_media_type(struct txgbe_hw *hw);
+s32 txgbe_disable_tx_laser_multispeed_fiber(struct txgbe_hw *hw);
+s32 txgbe_enable_tx_laser_multispeed_fiber(struct txgbe_hw *hw);
+s32 txgbe_flap_tx_laser_multispeed_fiber(struct txgbe_hw *hw);
+s32 txgbe_set_hard_rate_select_speed(struct txgbe_hw *hw, u32 speed);
+s32 txgbe_setup_mac_link(struct txgbe_hw *hw, u32 speed,
+ bool autoneg_wait_to_complete);
+s32 txgbe_check_mac_link(struct txgbe_hw *hw, u32 *speed,
+ bool *link_up, bool link_up_wait_to_complete);
+void txgbe_init_mac_link_ops(struct txgbe_hw *hw);
int txgbe_reset_misc(struct txgbe_hw *hw);
s32 txgbe_reset_hw(struct txgbe_hw *hw);
s32 txgbe_identify_phy(struct txgbe_hw *hw);
@@ -77,6 +91,13 @@ u32 txgbe_rd32_epcs(struct txgbe_hw *hw, u32 addr);
void txgbe_wr32_epcs(struct txgbe_hw *hw, u32 addr, u32 data);
void txgbe_wr32_ephy(struct txgbe_hw *hw, u32 addr, u32 data);
+s32 txgbe_set_link_to_kr(struct txgbe_hw *hw, bool autoneg);
+s32 txgbe_set_link_to_kx4(struct txgbe_hw *hw, bool autoneg);
+
+s32 txgbe_set_link_to_kx(struct txgbe_hw *hw,
+ u32 speed,
+ bool autoneg);
+
u8 fmgr_cmd_op(struct txgbe_hw *hw, u32 cmd, u32 cmd_addr);
u32 txgbe_flash_read_dword(struct txgbe_hw *hw, u32 addr);
@@ -200,9 +200,71 @@ static bool txgbe_is_sfp(struct txgbe_hw *hw)
}
}
+static bool txgbe_is_backplane(struct txgbe_hw *hw)
+{
+ switch (hw->phy.media_type) {
+ case txgbe_media_type_backplane:
+ return true;
+ default:
+ return false;
+ }
+}
+
+/**
+ * txgbe_sfp_link_config - set up SFP+ link
+ * @adapter: pointer to private adapter struct
+ **/
+static void txgbe_sfp_link_config(struct txgbe_adapter *adapter)
+{
+ /* We are assuming the worst case scenerio here, and that
+ * is that an SFP was inserted/removed after the reset
+ * but before SFP detection was enabled. As such the best
+ * solution is to just start searching as soon as we start
+ */
+
+ adapter->flags2 |= TXGBE_FLAG2_SFP_NEEDS_RESET;
+ adapter->sfp_poll_time = 0;
+}
+
static void txgbe_up_complete(struct txgbe_adapter *adapter)
{
+ struct txgbe_hw *hw = &adapter->hw;
+ u32 links_reg;
+
txgbe_get_hw_control(adapter);
+
+ /* enable the optics for SFP+ fiber */
+ TCALL(hw, mac.ops.enable_tx_laser);
+
+ /* make sure to complete pre-operations */
+ smp_mb__before_atomic();
+ clear_bit(__TXGBE_DOWN, &adapter->state);
+
+ if (txgbe_is_sfp(hw)) {
+ txgbe_sfp_link_config(adapter);
+ } else if (txgbe_is_backplane(hw)) {
+ adapter->flags |= TXGBE_FLAG_NEED_LINK_CONFIG;
+ txgbe_service_event_schedule(adapter);
+ }
+
+ links_reg = rd32(hw, TXGBE_CFG_PORT_ST);
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_UP) {
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_10G) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) |
+ TXGBE_MAC_TX_CFG_SPEED_10G);
+ } else if (links_reg & (TXGBE_CFG_PORT_ST_LINK_1G | TXGBE_CFG_PORT_ST_LINK_100M)) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) |
+ TXGBE_MAC_TX_CFG_SPEED_1G);
+ }
+ }
+
+ /* Set PF Reset Done bit so PF/VF Mail Ops can work */
+ wr32m(hw, TXGBE_CFG_PORT_CTL,
+ TXGBE_CFG_PORT_CTL_PFRSTD, TXGBE_CFG_PORT_CTL_PFRSTD);
}
void txgbe_reset(struct txgbe_adapter *adapter)
@@ -214,6 +276,13 @@ void txgbe_reset(struct txgbe_adapter *adapter)
if (TXGBE_REMOVED(hw->hw_addr))
return;
+ /* lock SFP init bit to prevent race conditions with the watchdog */
+ while (test_and_set_bit(__TXGBE_IN_SFP_INIT, &adapter->state))
+ usleep_range(1000, 2000);
+
+ /* clear all SFP and link config related flags while holding SFP_INIT */
+ adapter->flags2 &= ~TXGBE_FLAG2_SFP_NEEDS_RESET;
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_CONFIG;
err = TCALL(hw, mac.ops.init_hw);
switch (err) {
@@ -228,6 +297,7 @@ void txgbe_reset(struct txgbe_adapter *adapter)
dev_err(&adapter->pdev->dev, "Hardware Error: %d\n", err);
}
+ clear_bit(__TXGBE_IN_SFP_INIT, &adapter->state);
/* do not flush user set addresses */
memcpy(old_addr, &adapter->mac_table[0].addr, netdev->addr_len);
txgbe_flush_sw_mac_table(adapter);
@@ -254,6 +324,8 @@ void txgbe_disable_device(struct txgbe_adapter *adapter)
netif_carrier_off(netdev);
netif_tx_disable(netdev);
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_UPDATE;
+
del_timer_sync(&adapter->service_timer);
if (hw->bus.lan_id == 0)
@@ -283,8 +355,14 @@ void txgbe_disable_device(struct txgbe_adapter *adapter)
void txgbe_down(struct txgbe_adapter *adapter)
{
+ struct txgbe_hw *hw = &adapter->hw;
+
txgbe_disable_device(adapter);
txgbe_reset(adapter);
+
+ if (!(((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP)))
+ /* power down the optics for SFP+ fiber */
+ TCALL(&adapter->hw, mac.ops.disable_tx_laser);
}
/**
@@ -382,7 +460,11 @@ int txgbe_open(struct net_device *netdev)
*/
static void txgbe_close_suspend(struct txgbe_adapter *adapter)
{
+ struct txgbe_hw *hw = &adapter->hw;
+
txgbe_disable_device(adapter);
+ if (!((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP))
+ TCALL(hw, mac.ops.disable_tx_laser);
}
/**
@@ -437,12 +519,264 @@ static void txgbe_shutdown(struct pci_dev *pdev)
}
}
+/**
+ * txgbe_watchdog_update_link - update the link status
+ * @adapter: pointer to the device adapter structure
+ **/
+static void txgbe_watchdog_update_link(struct txgbe_adapter *adapter)
+{
+ struct txgbe_hw *hw = &adapter->hw;
+ u32 link_speed = adapter->link_speed;
+ bool link_up = adapter->link_up;
+ u32 reg;
+ u32 i = 1;
+
+ if (!(adapter->flags & TXGBE_FLAG_NEED_LINK_UPDATE))
+ return;
+
+ link_speed = TXGBE_LINK_SPEED_10GB_FULL;
+ link_up = true;
+ TCALL(hw, mac.ops.check_link, &link_speed, &link_up, false);
+
+ if (link_up || time_after(jiffies, (adapter->link_check_timeout +
+ TXGBE_TRY_LINK_TIMEOUT))) {
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_UPDATE;
+ }
+
+ for (i = 0; i < 3; i++) {
+ TCALL(hw, mac.ops.check_link, &link_speed, &link_up, false);
+ msleep(20);
+ }
+
+ adapter->link_up = link_up;
+ adapter->link_speed = link_speed;
+
+ if (link_up) {
+ if (link_speed & TXGBE_LINK_SPEED_10GB_FULL) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) | TXGBE_MAC_TX_CFG_TE |
+ TXGBE_MAC_TX_CFG_SPEED_10G);
+ } else if (link_speed & (TXGBE_LINK_SPEED_1GB_FULL |
+ TXGBE_LINK_SPEED_100_FULL | TXGBE_LINK_SPEED_10_FULL)) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) | TXGBE_MAC_TX_CFG_TE |
+ TXGBE_MAC_TX_CFG_SPEED_1G);
+ }
+
+ /* Re configure MAC RX */
+ reg = rd32(hw, TXGBE_MAC_RX_CFG);
+ wr32(hw, TXGBE_MAC_RX_CFG, reg);
+ wr32(hw, TXGBE_MAC_PKT_FLT, TXGBE_MAC_PKT_FLT_PR);
+ reg = rd32(hw, TXGBE_MAC_WDG_TIMEOUT);
+ wr32(hw, TXGBE_MAC_WDG_TIMEOUT, reg);
+ }
+}
+
+/**
+ * txgbe_watchdog_link_is_up - update netif_carrier status and
+ * print link up message
+ * @adapter: pointer to the device adapter structure
+ **/
+static void txgbe_watchdog_link_is_up(struct txgbe_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ u32 link_speed = adapter->link_speed;
+ const char *speed_str;
+
+ /* only continue if link was previously down */
+ if (netif_carrier_ok(netdev))
+ return;
+
+ switch (link_speed) {
+ case TXGBE_LINK_SPEED_10GB_FULL:
+ speed_str = "10 Gbps";
+ break;
+ case TXGBE_LINK_SPEED_1GB_FULL:
+ speed_str = "1 Gbps";
+ break;
+ case TXGBE_LINK_SPEED_100_FULL:
+ speed_str = "100 Mbps";
+ break;
+ case TXGBE_LINK_SPEED_10_FULL:
+ speed_str = "10 Mbps";
+ break;
+ default:
+ speed_str = "unknown speed";
+ break;
+ }
+
+ netif_info(adapter, drv, netdev,
+ "NIC Link is Up %s\n", speed_str);
+
+ netif_carrier_on(netdev);
+}
+
+/**
+ * txgbe_watchdog_link_is_down - update netif_carrier status and
+ * print link down message
+ * @adapter: pointer to the adapter structure
+ **/
+static void txgbe_watchdog_link_is_down(struct txgbe_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ adapter->link_up = false;
+ adapter->link_speed = 0;
+
+ /* only continue if link was up previously */
+ if (!netif_carrier_ok(netdev))
+ return;
+
+ netif_info(adapter, drv, netdev, "NIC Link is Down\n");
+ netif_carrier_off(netdev);
+}
+
+/**
+ * txgbe_watchdog_subtask - check and bring link up
+ * @adapter: pointer to the device adapter structure
+ **/
+static void txgbe_watchdog_subtask(struct txgbe_adapter *adapter)
+{
+ /* if interface is down do nothing */
+ if (test_bit(__TXGBE_DOWN, &adapter->state) ||
+ test_bit(__TXGBE_REMOVING, &adapter->state) ||
+ test_bit(__TXGBE_RESETTING, &adapter->state))
+ return;
+
+ txgbe_watchdog_update_link(adapter);
+
+ if (adapter->link_up)
+ txgbe_watchdog_link_is_up(adapter);
+ else
+ txgbe_watchdog_link_is_down(adapter);
+}
+
+/**
+ * txgbe_sfp_detection_subtask - poll for SFP+ cable
+ * @adapter: the txgbe adapter structure
+ **/
+static void txgbe_sfp_detection_subtask(struct txgbe_adapter *adapter)
+{
+ struct txgbe_hw *hw = &adapter->hw;
+ struct txgbe_mac_info *mac = &hw->mac;
+ s32 err;
+
+ /* not searching for SFP so there is nothing to do here */
+ if (!(adapter->flags2 & TXGBE_FLAG2_SFP_NEEDS_RESET))
+ return;
+
+ if (adapter->sfp_poll_time &&
+ time_after(adapter->sfp_poll_time, jiffies))
+ return; /* If not yet time to poll for SFP */
+
+ /* someone else is in init, wait until next service event */
+ if (test_and_set_bit(__TXGBE_IN_SFP_INIT, &adapter->state))
+ return;
+
+ adapter->sfp_poll_time = jiffies + TXGBE_SFP_POLL_JIFFIES - 1;
+
+ err = TCALL(hw, phy.ops.identify_sfp);
+ if (err == TXGBE_ERR_SFP_NOT_SUPPORTED)
+ goto sfp_out;
+
+ if (err == TXGBE_ERR_SFP_NOT_PRESENT) {
+ /* If no cable is present, then we need to reset
+ * the next time we find a good cable.
+ */
+ adapter->flags2 |= TXGBE_FLAG2_SFP_NEEDS_RESET;
+ }
+
+ /* exit on error */
+ if (err)
+ goto sfp_out;
+
+ /* exit if reset not needed */
+ if (!(adapter->flags2 & TXGBE_FLAG2_SFP_NEEDS_RESET))
+ goto sfp_out;
+
+ adapter->flags2 &= ~TXGBE_FLAG2_SFP_NEEDS_RESET;
+
+ if (hw->phy.multispeed_fiber) {
+ /* Set up dual speed SFP+ support */
+ mac->ops.setup_link = txgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_mac_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ } else {
+ mac->ops.setup_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ hw->phy.autoneg_advertised = 0;
+ }
+
+ adapter->flags |= TXGBE_FLAG_NEED_LINK_CONFIG;
+ netif_info(adapter, probe, adapter->netdev,
+ "detected SFP+: %d\n", hw->phy.sfp_type);
+
+sfp_out:
+ clear_bit(__TXGBE_IN_SFP_INIT, &adapter->state);
+
+ if (err == TXGBE_ERR_SFP_NOT_SUPPORTED && adapter->netdev_registered)
+ dev_err(&adapter->pdev->dev,
+ "failed to initialize because an unsupported SFP+ module type was detected.\n");
+}
+
+/**
+ * txgbe_sfp_link_config_subtask - set up link SFP after module install
+ * @adapter: the txgbe adapter structure
+ **/
+static void txgbe_sfp_link_config_subtask(struct txgbe_adapter *adapter)
+{
+ struct txgbe_hw *hw = &adapter->hw;
+ u8 device_type = hw->subsystem_device_id & 0xF0;
+ bool autoneg = false;
+ u32 speed;
+
+ if (!(adapter->flags & TXGBE_FLAG_NEED_LINK_CONFIG))
+ return;
+
+ /* someone else is in init, wait until next service event */
+ if (test_and_set_bit(__TXGBE_IN_SFP_INIT, &adapter->state))
+ return;
+
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_CONFIG;
+
+ if (device_type == TXGBE_ID_MAC_SGMII) {
+ speed = TXGBE_LINK_SPEED_1GB_FULL;
+ } else {
+ speed = hw->phy.autoneg_advertised;
+ if (!speed && hw->mac.ops.get_link_capabilities) {
+ TCALL(hw, mac.ops.get_link_capabilities, &speed, &autoneg);
+ /* setup the highest link when no autoneg */
+ if (!autoneg) {
+ if (speed & TXGBE_LINK_SPEED_10GB_FULL)
+ speed = TXGBE_LINK_SPEED_10GB_FULL;
+ }
+ }
+ }
+
+ TCALL(hw, mac.ops.setup_link, speed, false);
+
+ adapter->flags |= TXGBE_FLAG_NEED_LINK_UPDATE;
+ adapter->link_check_timeout = jiffies;
+ clear_bit(__TXGBE_IN_SFP_INIT, &adapter->state);
+}
+
static void txgbe_service_timer(struct timer_list *t)
{
struct txgbe_adapter *adapter = from_timer(adapter, t, service_timer);
+ struct txgbe_hw *hw = &adapter->hw;
unsigned long next_event_offset;
- next_event_offset = HZ * 2;
+ /* poll faster when waiting for link */
+ if (adapter->flags & TXGBE_FLAG_NEED_LINK_UPDATE) {
+ if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_KR_KX_KX4)
+ next_event_offset = HZ;
+ else
+ next_event_offset = HZ / 10;
+ } else {
+ next_event_offset = HZ * 2;
+ }
/* Reset the timer */
mod_timer(&adapter->service_timer, next_event_offset + jiffies);
@@ -469,6 +803,10 @@ static void txgbe_service_task(struct work_struct *work)
return;
}
+ txgbe_sfp_detection_subtask(adapter);
+ txgbe_sfp_link_config_subtask(adapter);
+ txgbe_watchdog_subtask(adapter);
+
txgbe_service_event_complete(adapter);
}
@@ -717,6 +1055,10 @@ static int txgbe_probe(struct pci_dev *pdev,
pci_set_drvdata(pdev, adapter);
adapter->netdev_registered = true;
+ if (!((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP))
+ /* power down the optics for SFP+ fiber */
+ TCALL(hw, mac.ops.disable_tx_laser);
+
/* carrier off reporting is important to ethtool even BEFORE open */
netif_carrier_off(netdev);
@@ -732,6 +1074,11 @@ static int txgbe_probe(struct pci_dev *pdev,
if (expected_gts > 0)
txgbe_check_minimum_link(adapter);
+ if ((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP)
+ netif_info(adapter, probe, netdev, "NCSI : support");
+ else
+ netif_info(adapter, probe, netdev, "NCSI : unsupported");
+
/* First try to read PBA as a string */
err = txgbe_read_pba_string(hw, part_str, TXGBE_PBANUM_LENGTH);
if (err)
@@ -756,6 +1103,16 @@ static int txgbe_probe(struct pci_dev *pdev,
/* add san mac addr to netdev */
txgbe_add_sanmac_netdev(netdev);
+ netif_info(adapter, probe, netdev,
+ "WangXun(R) 10 Gigabit Network Connection\n");
+
+ /* setup link for SFP devices with MNG FW, else wait for TXGBE_UP */
+ if (txgbe_mng_present(hw) && txgbe_is_sfp(hw) &&
+ ((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP))
+ TCALL(hw, mac.ops.setup_link,
+ TXGBE_LINK_SPEED_10GB_FULL | TXGBE_LINK_SPEED_1GB_FULL,
+ true);
+
return 0;
err_release_hw:
@@ -3,6 +3,29 @@
#include "txgbe_phy.h"
+/**
+ * txgbe_check_reset_blocked - check status of MNG FW veto bit
+ * @hw: pointer to the hardware structure
+ *
+ * This function checks the MMNGC.MNG_VETO bit to see if there are
+ * any constraints on link from manageability. For MAC's that don't
+ * have this bit just return faluse since the link can not be blocked
+ * via this method.
+ **/
+s32 txgbe_check_reset_blocked(struct txgbe_hw *hw)
+{
+ u32 mmngc;
+
+ mmngc = rd32(hw, TXGBE_MIS_ST);
+ if (mmngc & TXGBE_MIS_ST_MNG_VETO) {
+ ERROR_REPORT1(hw, TXGBE_ERROR_SOFTWARE,
+ "MNG_VETO bit detected.\n");
+ return true;
+ }
+
+ return false;
+}
+
/**
* txgbe_identify_module - Identifies module type
* @hw: pointer to hardware structure
@@ -39,6 +39,8 @@
#define TXGBE_SFF_VENDOR_OUI_AVAGO 0x00176A00
#define TXGBE_SFF_VENDOR_OUI_INTEL 0x001B2100
+s32 txgbe_check_reset_blocked(struct txgbe_hw *hw);
+
s32 txgbe_identify_module(struct txgbe_hw *hw);
s32 txgbe_identify_sfp_module(struct txgbe_hw *hw);
s32 txgbe_init_i2c(struct txgbe_hw *hw);
@@ -58,6 +58,14 @@
#define TXGBE_SR_XS_PCS_MMD_STATUS1 0x30001
#define TXGBE_SR_PCS_CTL2 0x30007
#define TXGBE_SR_PMA_MMD_CTL1 0x10000
+#define TXGBE_SR_MII_MMD_CTL 0x1F0000
+#define TXGBE_SR_MII_MMD_DIGI_CTL 0x1F8000
+#define TXGBE_SR_MII_MMD_AN_CTL 0x1F8001
+#define TXGBE_SR_MII_MMD_AN_ADV 0x1F0004
+#define TXGBE_SR_MII_MMD_AN_ADV_PAUSE(_v) ((0x3 & (_v)) << 7)
+#define TXGBE_SR_MII_MMD_AN_ADV_PAUSE_ASM 0x80
+#define TXGBE_SR_MII_MMD_AN_ADV_PAUSE_SYM 0x100
+#define TXGBE_SR_MII_MMD_LP_BABL 0x1F0005
#define TXGBE_SR_AN_MMD_CTL 0x70000
#define TXGBE_SR_AN_MMD_ADV_REG1 0x70010
#define TXGBE_SR_AN_MMD_ADV_REG1_PAUSE(_v) ((0x3 & (_v)) << 10)
@@ -68,10 +76,127 @@
#define TXGBE_VR_AN_KR_MODE_CL 0x78003
#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1 0x38000
#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS 0x38010
+#define TXGBE_PHY_MPLLA_CTL0 0x18071
+#define TXGBE_PHY_MPLLA_CTL3 0x18077
+#define TXGBE_PHY_MISC_CTL0 0x18090
+#define TXGBE_PHY_VCO_CAL_LD0 0x18092
+#define TXGBE_PHY_VCO_CAL_LD1 0x18093
+#define TXGBE_PHY_VCO_CAL_LD2 0x18094
+#define TXGBE_PHY_VCO_CAL_LD3 0x18095
+#define TXGBE_PHY_VCO_CAL_REF0 0x18096
+#define TXGBE_PHY_VCO_CAL_REF1 0x18097
+#define TXGBE_PHY_RX_AD_ACK 0x18098
+#define TXGBE_PHY_AFE_DFE_ENABLE 0x1805D
+#define TXGBE_PHY_DFE_TAP_CTL0 0x1805E
+#define TXGBE_PHY_RX_EQ_ATT_LVL0 0x18057
+#define TXGBE_PHY_RX_EQ_CTL0 0x18058
+#define TXGBE_PHY_RX_EQ_CTL 0x1805C
+#define TXGBE_PHY_TX_EQ_CTL0 0x18036
+#define TXGBE_PHY_TX_EQ_CTL1 0x18037
+#define TXGBE_PHY_TX_RATE_CTL 0x18034
+#define TXGBE_PHY_RX_RATE_CTL 0x18054
+#define TXGBE_PHY_TX_GEN_CTL2 0x18032
+#define TXGBE_PHY_RX_GEN_CTL2 0x18052
+#define TXGBE_PHY_RX_GEN_CTL3 0x18053
+#define TXGBE_PHY_MPLLA_CTL2 0x18073
+#define TXGBE_PHY_RX_POWER_ST_CTL 0x18055
+#define TXGBE_PHY_TX_POWER_ST_CTL 0x18035
+#define TXGBE_PHY_TX_GENCTRL1 0x18031
#define TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_R 0x0
#define TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X 0x1
#define TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK 0x3
+#define TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_1G 0x0
+#define TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_10G 0x2000
+#define TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_MASK 0x2000
+#define TXGBE_SR_PMA_MMD_CTL1_LB_EN 0x1
+#define TXGBE_SR_MII_MMD_CTL_AN_EN 0x1000
+#define TXGBE_SR_MII_MMD_CTL_RESTART_AN 0x0200
+#define TXGBE_SR_AN_MMD_CTL_RESTART_AN 0x0200
+#define TXGBE_SR_AN_MMD_CTL_ENABLE 0x1000
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX4 0x40
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX 0x20
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KR 0x80
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_MASK 0xFFFF
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_ENABLE 0x1000
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST 0x8000
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK 0x1C
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD 0x10
+
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_1GBASEX_KX 32
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_10GBASER_KR 33
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_OTHER 40
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_MASK 0xFF
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_1GBASEX_KX 0x56
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_10GBASER_KR 0x7B
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_OTHER 0x56
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_MASK 0x7FF
+#define TXGBE_PHY_MISC_CTL0_TX2RX_LB_EN_0 0x1
+#define TXGBE_PHY_MISC_CTL0_TX2RX_LB_EN_3_1 0xE
+#define TXGBE_PHY_MISC_CTL0_RX_VREF_CTRL 0x1F00
+#define TXGBE_PHY_VCO_CAL_LD0_1GBASEX_KX 1344
+#define TXGBE_PHY_VCO_CAL_LD0_10GBASER_KR 1353
+#define TXGBE_PHY_VCO_CAL_LD0_OTHER 1360
+#define TXGBE_PHY_VCO_CAL_LD0_MASK 0x1000
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_1GBASEX_KX 42
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_10GBASER_KR 41
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_OTHER 34
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_MASK 0x3F
+#define TXGBE_PHY_AFE_DFE_ENABLE_DFE_EN0 0x10
+#define TXGBE_PHY_AFE_DFE_ENABLE_AFE_EN0 0x1
+#define TXGBE_PHY_AFE_DFE_ENABLE_MASK 0xFF
+#define TXGBE_PHY_RX_EQ_CTL_CONT_ADAPT0 0x1
+#define TXGBE_PHY_RX_EQ_CTL_CONT_ADAPT_MASK 0xF
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_10GBASER_KR 0x0
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_RXAUI 0x1
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_1GBASEX_KX 0x3
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_OTHER 0x2
+#define TXGBE_PHY_TX_RATE_CTL_TX1_RATE_OTHER 0x20
+#define TXGBE_PHY_TX_RATE_CTL_TX2_RATE_OTHER 0x200
+#define TXGBE_PHY_TX_RATE_CTL_TX3_RATE_OTHER 0x2000
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_MASK 0x7
+#define TXGBE_PHY_TX_RATE_CTL_TX1_RATE_MASK 0x70
+#define TXGBE_PHY_TX_RATE_CTL_TX2_RATE_MASK 0x700
+#define TXGBE_PHY_TX_RATE_CTL_TX3_RATE_MASK 0x7000
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_10GBASER_KR 0x0
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_RXAUI 0x1
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_1GBASEX_KX 0x3
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_OTHER 0x2
+#define TXGBE_PHY_RX_RATE_CTL_RX1_RATE_OTHER 0x20
+#define TXGBE_PHY_RX_RATE_CTL_RX2_RATE_OTHER 0x200
+#define TXGBE_PHY_RX_RATE_CTL_RX3_RATE_OTHER 0x2000
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_MASK 0x7
+#define TXGBE_PHY_RX_RATE_CTL_RX1_RATE_MASK 0x70
+#define TXGBE_PHY_RX_RATE_CTL_RX2_RATE_MASK 0x700
+#define TXGBE_PHY_RX_RATE_CTL_RX3_RATE_MASK 0x7000
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_10GBASER_KR 0x200
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_10GBASER_KR_RXAUI 0x300
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_OTHER 0x100
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_MASK 0x300
+#define TXGBE_PHY_TX_GEN_CTL2_TX1_WIDTH_OTHER 0x400
+#define TXGBE_PHY_TX_GEN_CTL2_TX1_WIDTH_MASK 0xC00
+#define TXGBE_PHY_TX_GEN_CTL2_TX2_WIDTH_OTHER 0x1000
+#define TXGBE_PHY_TX_GEN_CTL2_TX2_WIDTH_MASK 0x3000
+#define TXGBE_PHY_TX_GEN_CTL2_TX3_WIDTH_OTHER 0x4000
+#define TXGBE_PHY_TX_GEN_CTL2_TX3_WIDTH_MASK 0xC000
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_10GBASER_KR 0x200
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_10GBASER_KR_RXAUI 0x300
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_OTHER 0x100
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_MASK 0x300
+#define TXGBE_PHY_RX_GEN_CTL2_RX1_WIDTH_OTHER 0x400
+#define TXGBE_PHY_RX_GEN_CTL2_RX1_WIDTH_MASK 0xC00
+#define TXGBE_PHY_RX_GEN_CTL2_RX2_WIDTH_OTHER 0x1000
+#define TXGBE_PHY_RX_GEN_CTL2_RX2_WIDTH_MASK 0x3000
+#define TXGBE_PHY_RX_GEN_CTL2_RX3_WIDTH_OTHER 0x4000
+#define TXGBE_PHY_RX_GEN_CTL2_RX3_WIDTH_MASK 0xC000
+
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_8 0x100
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_10 0x200
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_16P5 0x400
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_MASK 0x700
+
+#define TXGBE_XPCS_POWER_GOOD_MAX_POLLING_TIME 100
+#define TXGBE_PHY_INIT_DONE_POLLING_TIME 100
/**************** Global Registers ****************************/
/* chip control Registers */
@@ -282,6 +407,27 @@ struct txgbe_thermal_sensor_data {
#define TXGBE_CFG_LED_CTL_LINK_UP_SEL 0x00000001U
#define TXGBE_CFG_LED_CTL_LINK_OD_SHIFT 16
+/* GPIO Registers */
+#define TXGBE_GPIO_DR 0x14800
+#define TXGBE_GPIO_DDR 0x14804
+/*GPIO bit */
+#define TXGBE_GPIO_DR_0 0x00000001U /* SDP0 Data Value */
+#define TXGBE_GPIO_DR_1 0x00000002U /* SDP1 Data Value */
+#define TXGBE_GPIO_DR_2 0x00000004U /* SDP2 Data Value */
+#define TXGBE_GPIO_DR_3 0x00000008U /* SDP3 Data Value */
+#define TXGBE_GPIO_DR_4 0x00000010U /* SDP4 Data Value */
+#define TXGBE_GPIO_DR_5 0x00000020U /* SDP5 Data Value */
+#define TXGBE_GPIO_DR_6 0x00000040U /* SDP6 Data Value */
+#define TXGBE_GPIO_DR_7 0x00000080U /* SDP7 Data Value */
+#define TXGBE_GPIO_DDR_0 0x00000001U /* SDP0 IO direction */
+#define TXGBE_GPIO_DDR_1 0x00000002U /* SDP1 IO direction */
+#define TXGBE_GPIO_DDR_2 0x00000004U /* SDP1 IO direction */
+#define TXGBE_GPIO_DDR_3 0x00000008U /* SDP3 IO direction */
+#define TXGBE_GPIO_DDR_4 0x00000010U /* SDP4 IO direction */
+#define TXGBE_GPIO_DDR_5 0x00000020U /* SDP5 IO direction */
+#define TXGBE_GPIO_DDR_6 0x00000040U /* SDP6 IO direction */
+#define TXGBE_GPIO_DDR_7 0x00000080U /* SDP7 IO direction */
+
/*********************** Transmit DMA registers **************************/
/* transmit global control */
#define TXGBE_TDM_CTL 0x18000
@@ -662,6 +808,38 @@ struct txgbe_hic_reset {
/* Number of 100 microseconds we wait for PCI Express master disable */
#define TXGBE_PCI_MASTER_DISABLE_TIMEOUT 800
+
+/* Autonegotiation advertised speeds */
+typedef u32 txgbe_autoneg_advertised;
+/* Link speed */
+#define TXGBE_LINK_SPEED_UNKNOWN 0
+#define TXGBE_LINK_SPEED_100_FULL 1
+#define TXGBE_LINK_SPEED_1GB_FULL 2
+#define TXGBE_LINK_SPEED_10GB_FULL 4
+#define TXGBE_LINK_SPEED_10_FULL 8
+#define TXGBE_LINK_SPEED_AUTONEG (TXGBE_LINK_SPEED_100_FULL | \
+ TXGBE_LINK_SPEED_1GB_FULL | \
+ TXGBE_LINK_SPEED_10GB_FULL | \
+ TXGBE_LINK_SPEED_10_FULL)
+
+/* Physical layer type */
+typedef u32 txgbe_physical_layer;
+#define TXGBE_PHYSICAL_LAYER_UNKNOWN 0
+#define TXGBE_PHYSICAL_LAYER_10GBASE_T 0x0001
+#define TXGBE_PHYSICAL_LAYER_1000BASE_T 0x0002
+#define TXGBE_PHYSICAL_LAYER_100BASE_TX 0x0004
+#define TXGBE_PHYSICAL_LAYER_SFP_PLUS_CU 0x0008
+#define TXGBE_PHYSICAL_LAYER_10GBASE_LR 0x0010
+#define TXGBE_PHYSICAL_LAYER_10GBASE_LRM 0x0020
+#define TXGBE_PHYSICAL_LAYER_10GBASE_SR 0x0040
+#define TXGBE_PHYSICAL_LAYER_10GBASE_KX4 0x0080
+#define TXGBE_PHYSICAL_LAYER_1000BASE_KX 0x0200
+#define TXGBE_PHYSICAL_LAYER_1000BASE_BX 0x0400
+#define TXGBE_PHYSICAL_LAYER_10GBASE_KR 0x0800
+#define TXGBE_PHYSICAL_LAYER_10GBASE_XAUI 0x1000
+#define TXGBE_PHYSICAL_LAYER_SFP_ACTIVE_DA 0x2000
+#define TXGBE_PHYSICAL_LAYER_1000BASE_SX 0x4000
+
enum txgbe_eeprom_type {
txgbe_eeprom_uninitialized = 0,
txgbe_eeprom_spi,
@@ -812,6 +990,20 @@ struct txgbe_mac_operations {
s32 (*acquire_swfw_sync)(struct txgbe_hw *hw, u32 mask);
s32 (*release_swfw_sync)(struct txgbe_hw *hw, u32 mask);
+ /* Link */
+ s32 (*disable_tx_laser)(struct txgbe_hw *hw);
+ s32 (*enable_tx_laser)(struct txgbe_hw *hw);
+ s32 (*flap_tx_laser)(struct txgbe_hw *hw);
+ s32 (*setup_link)(struct txgbe_hw *hw, u32 speed,
+ bool autoneg_wait_to_complete);
+ s32 (*setup_mac_link)(struct txgbe_hw *hw, u32 speed,
+ bool autoneg_wait_to_complete);
+ s32 (*check_link)(struct txgbe_hw *hw, u32 *speed,
+ bool *link_up, bool link_up_wait_to_complete);
+ s32 (*get_link_capabilities)(struct txgbe_hw *hw, u32 *speed,
+ bool *autoneg);
+ s32 (*set_rate_select_speed)(struct txgbe_hw *hw, u32 speed);
+
/* RAR */
s32 (*set_rar)(struct txgbe_hw *hw, u32 index, u8 *addr, u64 pools,
u32 enable_addr);
@@ -878,7 +1070,9 @@ struct txgbe_phy_info {
enum txgbe_sfp_type sfp_type;
enum txgbe_media_type media_type;
u32 phy_semaphore_mask;
+ txgbe_autoneg_advertised autoneg_advertised;
bool multispeed_fiber;
+ txgbe_physical_layer link_mode;
};
enum txgbe_reset_type {
@@ -887,6 +1081,12 @@ enum txgbe_reset_type {
TXGBE_GLOBAL_RESET
};
+enum txgbe_link_status {
+ TXGBE_LINK_STATUS_NONE = 0,
+ TXGBE_LINK_STATUS_KX,
+ TXGBE_LINK_STATUS_KX4
+};
+
struct txgbe_hw {
u8 __iomem *hw_addr;
struct txgbe_mac_info mac;
@@ -901,6 +1101,7 @@ struct txgbe_hw {
u8 revision_id;
bool adapter_stopped;
enum txgbe_reset_type reset_type;
+ enum txgbe_link_status link_status;
u16 oem_ssid;
u16 oem_svid;
};
Get link capabilities, setup MAC and PHY link, and support to enable or disable Tx laser. Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> --- .../device_drivers/ethernet/wangxun/txgbe.rst | 5 + drivers/net/ethernet/wangxun/txgbe/txgbe.h | 25 + drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c | 1314 ++++++++++++++++- drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h | 21 + .../net/ethernet/wangxun/txgbe/txgbe_main.c | 359 ++++- .../net/ethernet/wangxun/txgbe/txgbe_phy.c | 23 + .../net/ethernet/wangxun/txgbe/txgbe_phy.h | 2 + .../net/ethernet/wangxun/txgbe/txgbe_type.h | 201 +++ 8 files changed, 1946 insertions(+), 4 deletions(-)