@@ -51,6 +51,11 @@ The following is a list of 3rd party SFP+ modules that have been tested and veri
| WTD | SFP+ | RTXM228-551 |
+----------+----------------------+----------------------+
+Laser turns off for SFP+ when ifconfig ethX down
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+"ifconfig ethX down" turns off the laser for SFP+ fiber adapters.
+"ifconfig ethX up" turns on the laser.
+
Support
=======
@@ -6,6 +6,7 @@
#include <net/ip.h>
#include <linux/etherdevice.h>
+#include <linux/timecounter.h>
#include "txgbe_type.h"
@@ -28,6 +29,22 @@ struct txgbe_mac_addr {
#define TXGBE_MAC_STATE_MODIFIED 0x2
#define TXGBE_MAC_STATE_IN_USE 0x4
+/* default to trying for four seconds */
+#define TXGBE_TRY_LINK_TIMEOUT (4 * HZ)
+#define TXGBE_SFP_POLL_JIFFIES (2 * HZ) /* SFP poll every 2 seconds */
+
+/**
+ * txgbe_adapter.flag
+ **/
+#define TXGBE_FLAG_NEED_LINK_UPDATE BIT(0)
+#define TXGBE_FLAG_NEED_LINK_CONFIG BIT(1)
+
+/**
+ * txgbe_adapter.flag2
+ **/
+#define TXGBE_FLAG2_MNG_REG_ACCESS_DISABLED BIT(0)
+#define TXGBE_FLAG2_SFP_NEEDS_RESET BIT(1)
+
/* board specific private data structure */
struct txgbe_adapter {
u8 __iomem *io_addr; /* Mainly for iounmap use */
@@ -37,6 +54,8 @@ struct txgbe_adapter {
unsigned long state;
+ u32 flags;
+ u32 flags2;
/* Tx fast path data */
int num_tx_queues;
@@ -47,6 +66,11 @@ struct txgbe_adapter {
struct txgbe_hw hw;
u16 msg_enable;
+ u32 link_speed;
+ bool link_up;
+ unsigned long sfp_poll_time;
+ unsigned long link_check_timeout;
+
struct timer_list service_timer;
struct work_struct service_task;
@@ -66,6 +90,7 @@ enum txgbe_state_t {
__TXGBE_REMOVING,
__TXGBE_SERVICE_SCHED,
__TXGBE_SERVICE_INITED,
+ __TXGBE_IN_SFP_INIT,
};
/* needed by txgbe_main.c */
@@ -121,6 +121,35 @@ static void txgbe_init_uta_tables_dummy(struct txgbe_hw *TUP0)
{
}
+static int txgbe_get_link_capabilities_dummy(struct txgbe_hw *TUP0,
+ u32 *TUP1, bool *TUP2)
+{
+ return -EPERM;
+}
+
+static void txgbe_check_mac_link_dummy(struct txgbe_hw *TUP0, u32 *TUP1,
+ bool *TUP3, bool TUP4)
+{
+}
+
+static int txgbe_setup_link_dummy(struct txgbe_hw *TUP0, u32 TUP1, bool TUP2)
+{
+ return -EPERM;
+}
+
+static int txgbe_setup_mac_link_dummy(struct txgbe_hw *TUP0, u32 TUP1, bool TUP2)
+{
+ return -EPERM;
+}
+
+static void txgbe_flap_tx_laser_multispeed_fiber_dummy(struct txgbe_hw *TUP0)
+{
+}
+
+static void txgbe_set_hard_rate_select_speed_dummy(struct txgbe_hw *TUP0, u32 TUP1)
+{
+}
+
static int txgbe_set_fw_drv_ver_dummy(struct txgbe_hw *TUP0, u8 TUP1,
u8 TUP2, u8 TUP3, u8 TUP4)
{
@@ -131,6 +160,14 @@ static void txgbe_init_thermal_sensor_thresh_dummy(struct txgbe_hw *TUP0)
{
}
+static void txgbe_disable_tx_laser_multispeed_fiber_dummy(struct txgbe_hw *TUP0)
+{
+}
+
+static void txgbe_enable_tx_laser_multispeed_fiber_dummy(struct txgbe_hw *TUP0)
+{
+}
+
/* struct txgbe_eeprom_operations */
static void txgbe_init_eeprom_params_dummy(struct txgbe_hw *TUP0)
{
@@ -191,6 +228,16 @@ static void txgbe_init_ops_dummy(struct txgbe_hw *hw)
mac->ops.set_vmdq_san_mac = txgbe_set_vmdq_san_mac_dummy;
mac->ops.init_uta_tables = txgbe_init_uta_tables_dummy;
+ /* Link */
+ mac->ops.disable_tx_laser = txgbe_disable_tx_laser_multispeed_fiber_dummy;
+ mac->ops.enable_tx_laser = txgbe_enable_tx_laser_multispeed_fiber_dummy;
+ mac->ops.get_link_capabilities = txgbe_get_link_capabilities_dummy;
+ mac->ops.check_link = txgbe_check_mac_link_dummy;
+ mac->ops.setup_link = txgbe_setup_link_dummy;
+ mac->ops.setup_mac_link = txgbe_setup_mac_link_dummy;
+ mac->ops.flap_tx_laser = txgbe_flap_tx_laser_multispeed_fiber_dummy;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed_dummy;
+
/* EEPROM */
eeprom->ops.init_params = txgbe_init_eeprom_params_dummy;
eeprom->ops.calc_checksum = txgbe_calc_eeprom_checksum_dummy;
@@ -29,6 +29,34 @@ u32 txgbe_rd32_epcs(struct txgbe_hw *hw, u32 addr)
return data;
}
+void txgbe_wr32_ephy(struct txgbe_hw *hw, u32 addr, u32 data)
+{
+ unsigned int offset;
+
+ /* Set the LAN port indicator to offset[1] */
+ /* 1st, write the offset to IDA_ADDR register */
+ offset = TXGBE_ETHPHY_IDA_ADDR;
+ wr32(hw, offset, addr);
+
+ /* 2nd, read the data from IDA_DATA register */
+ offset = TXGBE_ETHPHY_IDA_DATA;
+ wr32(hw, offset, data);
+}
+
+void txgbe_wr32_epcs(struct txgbe_hw *hw, u32 addr, u32 data)
+{
+ unsigned int offset;
+
+ /* Set the LAN port indicator to offset[1] */
+ /* 1st, write the offset to IDA_ADDR register */
+ offset = TXGBE_XPCS_IDA_ADDR;
+ wr32(hw, offset, addr);
+
+ /* 2nd, read the data from IDA_DATA register */
+ offset = TXGBE_XPCS_IDA_DATA;
+ wr32(hw, offset, data);
+}
+
int txgbe_init_hw(struct txgbe_hw *hw)
{
int status;
@@ -992,10 +1020,12 @@ int txgbe_reset_hostif(struct txgbe_hw *hw)
continue;
if (reset_cmd.hdr.cmd_or_resp.ret_status ==
- FW_CEM_RESP_STATUS_SUCCESS)
+ FW_CEM_RESP_STATUS_SUCCESS) {
ret_val = 0;
- else
+ hw->link_status = TXGBE_LINK_STATUS_NONE;
+ } else {
ret_val = -EFAULT;
+ }
break;
}
@@ -1107,6 +1137,124 @@ bool txgbe_check_mng_access(struct txgbe_hw *hw)
return true;
}
+/**
+ * txgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed in the MAC and/or PHY register and restarts link.
+ **/
+int txgbe_setup_mac_link_multispeed_fiber(struct txgbe_hw *hw,
+ u32 speed,
+ bool autoneg_wait_to_complete)
+{
+ u32 highest_link_speed = TXGBE_LINK_SPEED_UNKNOWN;
+ u32 link_speed = TXGBE_LINK_SPEED_UNKNOWN;
+ bool autoneg, link_up = false;
+ u32 speedcnt = 0;
+ int status = 0;
+ u32 i = 0;
+
+ /* Mask off requested but non-supported speeds */
+ status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
+ if (status != 0)
+ return status;
+
+ speed &= link_speed;
+
+ /* Try each speed one by one, highest priority first. We do this in
+ * software because 10Gb fiber doesn't support speed autonegotiation.
+ */
+ if (speed & TXGBE_LINK_SPEED_10GB_FULL) {
+ speedcnt++;
+ highest_link_speed = TXGBE_LINK_SPEED_10GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_speed == TXGBE_LINK_SPEED_10GB_FULL && link_up)
+ goto out;
+
+ /* Allow module to change analog characteristics (1G->10G) */
+ msleep(40);
+
+ status = hw->mac.ops.setup_mac_link(hw,
+ TXGBE_LINK_SPEED_10GB_FULL,
+ autoneg_wait_to_complete);
+ if (status != 0)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ hw->mac.ops.flap_tx_laser(hw);
+
+ /* Wait for the controller to acquire link. Per IEEE 802.3ap,
+ * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * attempted. sapphire uses the same timing for 10g SFI.
+ */
+ for (i = 0; i < 5; i++) {
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_up)
+ goto out;
+ }
+ }
+
+ if (speed & TXGBE_LINK_SPEED_1GB_FULL) {
+ speedcnt++;
+ if (highest_link_speed == TXGBE_LINK_SPEED_UNKNOWN)
+ highest_link_speed = TXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_speed == TXGBE_LINK_SPEED_1GB_FULL && link_up)
+ goto out;
+
+ /* Allow module to change analog characteristics (10G->1G) */
+ msleep(40);
+
+ status = hw->mac.ops.setup_mac_link(hw,
+ TXGBE_LINK_SPEED_1GB_FULL,
+ autoneg_wait_to_complete);
+ if (status != 0)
+ return status;
+
+ /* Flap the Tx laser if it has not already been done */
+ hw->mac.ops.flap_tx_laser(hw);
+
+ /* Wait for the link partner to also set speed */
+ msleep(100);
+
+ /* If we have link, just jump out */
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_up)
+ goto out;
+ }
+
+ /* We didn't get link. Configure back to the highest speed we tried,
+ * (if there was more than one). We call ourselves back with just the
+ * single highest speed that the user requested.
+ */
+ if (speedcnt > 1)
+ status = txgbe_setup_mac_link_multispeed_fiber(hw,
+ highest_link_speed,
+ autoneg_wait_to_complete);
+
+out:
+ /* Set autoneg_advertised value based on input link speed */
+ hw->phy.autoneg_advertised = 0;
+
+ if (speed & TXGBE_LINK_SPEED_10GB_FULL)
+ hw->phy.autoneg_advertised |= TXGBE_LINK_SPEED_10GB_FULL;
+
+ if (speed & TXGBE_LINK_SPEED_1GB_FULL)
+ hw->phy.autoneg_advertised |= TXGBE_LINK_SPEED_1GB_FULL;
+
+ return status;
+}
+
int txgbe_check_flash_load(struct txgbe_hw *hw, u32 check_bit)
{
u32 i = 0, reg = 0;
@@ -1132,11 +1280,41 @@ int txgbe_check_flash_load(struct txgbe_hw *hw, u32 check_bit)
return err;
}
+void txgbe_init_mac_link_ops(struct txgbe_hw *hw)
+{
+ struct txgbe_mac_info *mac = &hw->mac;
+
+ /* enable the laser control functions for SFP+ fiber
+ * and MNG not enabled
+ */
+ if (hw->phy.media_type == txgbe_media_type_fiber) {
+ mac->ops.disable_tx_laser = txgbe_disable_tx_laser_multispeed_fiber;
+ mac->ops.enable_tx_laser = txgbe_enable_tx_laser_multispeed_fiber;
+ mac->ops.flap_tx_laser = txgbe_flap_tx_laser_multispeed_fiber;
+ } else {
+ mac->ops.disable_tx_laser = NULL;
+ mac->ops.enable_tx_laser = NULL;
+ mac->ops.flap_tx_laser = NULL;
+ }
+
+ if (hw->phy.multispeed_fiber) {
+ /* Set up dual speed SFP+ support */
+ mac->ops.setup_link = txgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_mac_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ } else {
+ mac->ops.setup_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ }
+}
+
/**
* txgbe_init_phy_ops - PHY/SFP specific init
* @hw: pointer to hardware structure
*
- * Perform the SFP init if necessary.
+ * Initialize any function pointers that were not able to be
+ * set during init_shared_code because the PHY/SFP type was
+ * not known. Perform the SFP init if necessary.
**/
int txgbe_init_phy_ops(struct txgbe_hw *hw)
{
@@ -1145,6 +1323,11 @@ int txgbe_init_phy_ops(struct txgbe_hw *hw)
txgbe_init_i2c(hw);
/* Identify the PHY or SFP module */
ret_val = hw->phy.ops.identify(hw);
+ if (ret_val != 0 && hw->phy.type == txgbe_phy_sfp_unsupported)
+ return ret_val;
+
+ /* Setup function pointers based on detected SFP module and speeds */
+ txgbe_init_mac_link_ops(hw);
return ret_val;
}
@@ -1190,6 +1373,9 @@ void txgbe_init_ops(struct txgbe_hw *hw)
mac->ops.set_vmdq_san_mac = txgbe_set_vmdq_san_mac;
mac->ops.init_uta_tables = txgbe_init_uta_tables;
+ /* Link */
+ mac->ops.get_link_capabilities = txgbe_get_link_capabilities;
+ mac->ops.check_link = txgbe_check_mac_link;
mac->num_rar_entries = TXGBE_SP_RAR_ENTRIES;
mac->max_rx_queues = TXGBE_SP_MAX_RX_QUEUES;
mac->max_tx_queues = TXGBE_SP_MAX_TX_QUEUES;
@@ -1206,6 +1392,121 @@ void txgbe_init_ops(struct txgbe_hw *hw)
mac->ops.init_thermal_sensor_thresh = txgbe_init_thermal_sensor_thresh;
}
+/**
+ * txgbe_get_link_capabilities - Determines link capabilities
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @autoneg: true when autoneg or autotry is enabled
+ **/
+int txgbe_get_link_capabilities(struct txgbe_hw *hw,
+ u32 *speed,
+ bool *autoneg)
+{
+ u32 sr_pcs_ctl, sr_pma_mmd_ctl1, sr_an_mmd_ctl;
+ u32 sr_an_mmd_adv_reg2;
+
+ /* Check if 1G SFP module. */
+ if (hw->phy.sfp_type == txgbe_sfp_type_1g_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_cu_core1 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_lx_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_lx_core1 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_sx_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_1g_sx_core1) {
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = false;
+ } else if (hw->phy.multispeed_fiber) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL |
+ TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = true;
+ }
+ /* SFP */
+ else if (hw->phy.media_type == txgbe_media_type_fiber) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ }
+ /* SGMII */
+ else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_SGMII) {
+ *speed = TXGBE_LINK_SPEED_1GB_FULL |
+ TXGBE_LINK_SPEED_100_FULL |
+ TXGBE_LINK_SPEED_10_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_1000BASE_T |
+ TXGBE_PHYSICAL_LAYER_100BASE_TX;
+ /* MAC XAUI */
+ } else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_XAUI) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ /* MAC SGMII */
+ } else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_SGMII) {
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ } else { /* KR KX KX4 */
+ /* Determine link capabilities based on the stored value,
+ * which represents EEPROM defaults. If value has not
+ * been stored, use the current register values.
+ */
+ if (hw->mac.orig_link_settings_stored) {
+ sr_pcs_ctl = hw->mac.orig_sr_pcs_ctl2;
+ sr_pma_mmd_ctl1 = hw->mac.orig_sr_pma_mmd_ctl1;
+ sr_an_mmd_ctl = hw->mac.orig_sr_an_mmd_ctl;
+ sr_an_mmd_adv_reg2 = hw->mac.orig_sr_an_mmd_adv_reg2;
+ } else {
+ sr_pcs_ctl = txgbe_rd32_epcs(hw, TXGBE_SR_PCS_CTL2);
+ sr_pma_mmd_ctl1 = txgbe_rd32_epcs(hw,
+ TXGBE_SR_PMA_MMD_CTL1);
+ sr_an_mmd_ctl = txgbe_rd32_epcs(hw,
+ TXGBE_SR_AN_MMD_CTL);
+ sr_an_mmd_adv_reg2 = txgbe_rd32_epcs(hw,
+ TXGBE_SR_AN_MMD_ADV_REG2);
+ }
+
+ if ((sr_pcs_ctl & TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK) ==
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X &&
+ (sr_pma_mmd_ctl1 & TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_MASK) ==
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_1G &&
+ (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) == 0) {
+ /* 1G or KX - no backplane auto-negotiation */
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ } else if ((sr_pcs_ctl & TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK) ==
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X &&
+ (sr_pma_mmd_ctl1 & TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_MASK) ==
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_10G &&
+ (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) == 0) {
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ } else if ((sr_pcs_ctl & TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK) ==
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_R &&
+ (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) == 0) {
+ /* 10 GbE serial link (KR -no backplane auto-negotiation) */
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ *autoneg = false;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KR;
+ } else if (sr_an_mmd_ctl & TXGBE_SR_AN_MMD_CTL_ENABLE) {
+ /* KX/KX4/KR backplane auto-negotiation enable */
+ *speed = TXGBE_LINK_SPEED_UNKNOWN;
+ if (sr_an_mmd_adv_reg2 & TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KR)
+ *speed |= TXGBE_LINK_SPEED_10GB_FULL;
+ if (sr_an_mmd_adv_reg2 & TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX4)
+ *speed |= TXGBE_LINK_SPEED_10GB_FULL;
+ if (sr_an_mmd_adv_reg2 & TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX)
+ *speed |= TXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = true;
+ hw->phy.link_mode = TXGBE_PHYSICAL_LAYER_10GBASE_KR |
+ TXGBE_PHYSICAL_LAYER_10GBASE_KX4 |
+ TXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ } else {
+ return -ENODEV;
+ }
+ }
+
+ return 0;
+}
+
/**
* txgbe_get_media_type - Get media type
* @hw: pointer to hardware structure
@@ -1245,12 +1546,887 @@ enum txgbe_media_type txgbe_get_media_type(struct txgbe_hw *hw)
return media_type;
}
+/**
+ * txgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser
+ * @hw: pointer to hardware structure
+ *
+ * The base drivers may require better control over SFP+ module
+ * PHY states. This includes selectively shutting down the Tx
+ * laser on the PHY, effectively halting physical link.
+ **/
+void txgbe_disable_tx_laser_multispeed_fiber(struct txgbe_hw *hw)
+{
+ u32 esdp_reg = rd32(hw, TXGBE_GPIO_DR);
+
+ if (!(hw->phy.media_type == txgbe_media_type_fiber))
+ return;
+
+ /* Disable Tx laser; allow 100us to go dark per spec */
+ esdp_reg |= TXGBE_GPIO_DR_1 | TXGBE_GPIO_DR_0;
+ wr32(hw, TXGBE_GPIO_DR, esdp_reg);
+ TXGBE_WRITE_FLUSH(hw);
+ usleep_range(100, 200);
+}
+
+/**
+ * txgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser
+ * @hw: pointer to hardware structure
+ *
+ * The base drivers may require better control over SFP+ module
+ * PHY states. This includes selectively turning on the Tx
+ * laser on the PHY, effectively starting physical link.
+ **/
+void txgbe_enable_tx_laser_multispeed_fiber(struct txgbe_hw *hw)
+{
+ if (hw->phy.media_type != txgbe_media_type_fiber)
+ return;
+
+ /* Enable Tx laser; allow 100ms to light up */
+ wr32m(hw, TXGBE_GPIO_DR,
+ TXGBE_GPIO_DR_0 | TXGBE_GPIO_DR_1, 0);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(100);
+}
+
+/**
+ * txgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser
+ * @hw: pointer to hardware structure
+ *
+ * When the driver changes the link speeds that it can support,
+ * it sets autotry_restart to true to indicate that we need to
+ * initiate a new autotry session with the link partner. To do
+ * so, we set the speed then disable and re-enable the Tx laser, to
+ * alert the link partner that it also needs to restart autotry on its
+ * end. This is consistent with true clause 37 autoneg, which also
+ * involves a loss of signal.
+ **/
+void txgbe_flap_tx_laser_multispeed_fiber(struct txgbe_hw *hw)
+{
+ if (hw->mac.autotry_restart) {
+ txgbe_disable_tx_laser_multispeed_fiber(hw);
+ txgbe_enable_tx_laser_multispeed_fiber(hw);
+ hw->mac.autotry_restart = false;
+ }
+}
+
+/**
+ * txgbe_set_hard_rate_select_speed - Set module link speed
+ * @hw: pointer to hardware structure
+ * @speed: link speed to set
+ *
+ * Set module link speed via RS0/RS1 rate select pins.
+ */
+void txgbe_set_hard_rate_select_speed(struct txgbe_hw *hw, u32 speed)
+{
+ u32 esdp_reg = rd32(hw, TXGBE_GPIO_DR);
+
+ switch (speed) {
+ case TXGBE_LINK_SPEED_10GB_FULL:
+ esdp_reg |= TXGBE_GPIO_DR_5 | TXGBE_GPIO_DR_4;
+ break;
+ case TXGBE_LINK_SPEED_1GB_FULL:
+ esdp_reg &= ~(TXGBE_GPIO_DR_5 | TXGBE_GPIO_DR_4);
+ break;
+ default:
+ txgbe_info(hw, "Invalid fixed module speed\n");
+ return;
+ }
+
+ wr32(hw, TXGBE_GPIO_DDR,
+ TXGBE_GPIO_DDR_5 | TXGBE_GPIO_DDR_4 |
+ TXGBE_GPIO_DDR_1 | TXGBE_GPIO_DDR_0);
+
+ wr32(hw, TXGBE_GPIO_DR, esdp_reg);
+
+ TXGBE_WRITE_FLUSH(hw);
+}
+
+static void txgbe_set_sgmii_an37_ability(struct txgbe_hw *hw)
+{
+ u32 value;
+
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0x3002);
+ /* for sgmii + external phy, set to 0x0105 (phy sgmii mode) */
+ /* for sgmii direct link, set to 0x010c (mac sgmii mode) */
+ if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_SGMII ||
+ hw->phy.media_type == txgbe_media_type_fiber) {
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x010c);
+ } else if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_SGMII ||
+ (hw->subsystem_device_id & 0xF0) == TXGBE_ID_XAUI) {
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x0105);
+ }
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_DIGI_CTL, 0x0200);
+ value = txgbe_rd32_epcs(hw, TXGBE_SR_MII_MMD_CTL);
+ value = (value & ~0x1200) | (0x1 << 12) | (0x1 << 9);
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_CTL, value);
+}
+
+void txgbe_set_link_to_kr(struct txgbe_hw *hw, bool autoneg)
+{
+ int status = 0;
+ u32 value;
+
+ /* 1. Wait xpcs power-up good */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ (value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD,
+ 10000, 1000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS);
+ if (status == -ETIMEDOUT) {
+ txgbe_info(hw, "xpcs power-up timeout.\n");
+ return;
+ }
+
+ txgbe_dbg(hw, "It is set to kr.\n");
+
+ txgbe_wr32_epcs(hw, 0x78001, 0x7);
+
+ /* 2. Disable xpcs AN-73 */
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x3000);
+ txgbe_wr32_epcs(hw, TXGBE_VR_AN_KR_MODE_CL, 0x1);
+
+ /* 3. Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL3 Register */
+ /* Bit[10:0](MPLLA_BANDWIDTH) = 11'd123 (default: 11'd16) */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3,
+ TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_10GBASER_KR);
+
+ /* 4. Set VR_XS_PMA_Gen5_12G_MISC_CTRL0 Register */
+ /* Bit[12:8](RX_VREF_CTRL) = 5'hF (default: 5'h11) */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+
+ /* 5. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register */
+ /* Bit[15:8](VGA1/2_GAIN_0) = 8'h77,
+ * Bit[7:5](CTLE_POLE_0) = 3'h2
+ * Bit[4:0](CTLE_BOOST_0) = 4'hA
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, 0x774A);
+
+ /* 6. Set VR_MII_Gen5_12G_RX_GENCTRL3 Register */
+ /* Bit[2:0](LOS_TRSHLD_0) = 3'h4 (default: 3) */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, 0x0004);
+ /* 7. Initialize the mode by setting VR XS or PCS MMD Digital */
+ /* Control1 Register Bit[15](VR_RST) */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+ /* wait phy initialization done */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ !(value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST),
+ 100000, 10000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1);
+ if (status == -ETIMEDOUT)
+ txgbe_info(hw, "PHY initialization timeout.\n");
+}
+
+void txgbe_set_link_to_kx4(struct txgbe_hw *hw, bool autoneg)
+{
+ int status = 0;
+ u32 value, i;
+
+ /* check link status, if already set, skip setting it again */
+ if (hw->link_status == TXGBE_LINK_STATUS_KX4)
+ return;
+
+ txgbe_dbg(hw, "It is set to kx4.\n");
+
+ /* 1. Wait xpcs power-up good */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ (value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD,
+ 10000, 1000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS);
+ if (status == -ETIMEDOUT) {
+ txgbe_info(hw, "xpcs power-up timeout.\n");
+ return;
+ }
+
+ wr32m(hw, TXGBE_MAC_TX_CFG, TXGBE_MAC_TX_CFG_TE, ~TXGBE_MAC_TX_CFG_TE);
+
+ /* 2. Disable xpcs AN-73 */
+ if (!autoneg)
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x0);
+ else
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x3000);
+
+ /* Disable PHY MPLLA for eth mode change(after ECO) */
+ txgbe_wr32_ephy(hw, 0x4, 0x250A);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(20);
+
+ /* Set the eth change_mode bit first in mis_rst register
+ * for corresponding LAN port
+ */
+ if (hw->bus.lan_id == 0)
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN0_CHG_ETH_MODE);
+ else
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN1_CHG_ETH_MODE);
+
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b01
+ * PCS_TYPE_SEL: non KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2,
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X);
+ /* Set SR PMA MMD Control1 Register Bit[13] = 1'b1 SS13: 10G speed */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1,
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_10G);
+
+ value = (0xf5f0 & ~0x7F0) | (0x5 << 8) | (0x7 << 5) | 0xF0;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+
+ if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_MAC_XAUI)
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+ else
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0x4F00);
+
+ for (i = 0; i < 4; i++) {
+ if (i == 0)
+ value = (0x45 & ~0xFFFF) | (0x7 << 12) |
+ (0x7 << 8) | 0x6;
+ else
+ value = (0xff06 & ~0xFFFF) | (0x7 << 12) |
+ (0x7 << 8) | 0x6;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0 + i, value);
+ }
+
+ value = 0x0 & ~0x7777;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0);
+
+ value = (0x6db & ~0xFFF) | (0x1 << 9) | (0x1 << 6) | (0x1 << 3) | 0x1;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, value);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA */
+ /* Control 0 Register Bit[7:0] = 8'd40 MPLLA_MULTIPLIER */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0,
+ TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_OTHER);
+ /* Set VR XS, PMA or MII Synopsys Enterprise Gen5 12G PHY MPLLA */
+ /* Control 3 Register Bit[10:0] = 11'd86 MPLLA_BANDWIDTH */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3,
+ TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 0 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_0 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 1 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD1, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 2 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_2 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD2, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Load 3 Register Bit[12:0] = 13'd1360 VCO_LD_VAL_3 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD3, TXGBE_PHY_VCO_CAL_LD0_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Reference 0 Register Bit[5:0] = 6'd34 VCO_REF_LD_0/1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO */
+ /* Calibration Reference 1 Register Bit[5:0] = 6'd34 VCO_REF_LD_2/3 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF1, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY AFE-DFE */
+ /* Enable Register Bit[7:0] = 8'd0 AFE_EN_0/3_1, DFE_EN_0/3_1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, 0x0);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx */
+ /* Equalization Control 4 Register Bit[3:0] = 4'd0 CONT_ADAPT_0/3_1 */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, 0x00F0);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx Rate */
+ /* Control Register Bit[14:12], Bit[10:8], Bit[6:4], Bit[2:0],
+ * all rates to 3'b010 TX0/1/2/3_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx Rate */
+ /* Control Register Bit[13:12], Bit[9:8], Bit[5:4], Bit[1:0],
+ * all rates to 2'b10 RX0/1/2/3_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL, 0x2222);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx General */
+ /* Control 2 Register Bit[15:8] = 2'b01 TX0/1/2/3_WIDTH: 10bits */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2, 0x5500);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx General */
+ /* Control 2 Register Bit[15:8] = 2'b01 RX0/1/2/3_WIDTH: 10bits */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2, 0x5500);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 2 Register Bit[10:8] = 3'b010
+ * MPLLA_DIV16P5_CLK_EN=0, MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2,
+ TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_10);
+
+ txgbe_wr32_epcs(hw, 0x1f0000, 0x0);
+ txgbe_wr32_epcs(hw, 0x1f8001, 0x0);
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_DIGI_CTL, 0x0);
+
+ /* 10. Initialize the mode by setting VR XS or PCS MMD Digital Control1
+ * Register Bit[15](VR_RST)
+ */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+
+ /* wait phy initialization done */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ !(value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST),
+ 100000, 10000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1);
+ if (status == -ETIMEDOUT) {
+ txgbe_info(hw, "PHY initialization timeout.\n");
+ return;
+ }
+
+ /* if success, set link status */
+ hw->link_status = TXGBE_LINK_STATUS_KX4;
+}
+
+void txgbe_set_link_to_kx(struct txgbe_hw *hw, u32 speed, bool autoneg)
+{
+ int status = 0;
+ u32 wdata = 0;
+ u32 value, i;
+
+ /* check link status, if already set, skip setting it again */
+ if (hw->link_status == TXGBE_LINK_STATUS_KX)
+ return;
+
+ txgbe_dbg(hw, "It is set to kx. speed =0x%x\n", speed);
+
+ /* 1. Wait xpcs power-up good */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ (value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD,
+ 10000, 1000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS);
+ if (status == -ETIMEDOUT) {
+ txgbe_info(hw, "xpcs power-up timeout.\n");
+ return;
+ }
+
+ wr32m(hw, TXGBE_MAC_TX_CFG, TXGBE_MAC_TX_CFG_TE, ~TXGBE_MAC_TX_CFG_TE);
+
+ /* 2. Disable xpcs AN-73 */
+ if (!autoneg)
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x0);
+ else
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x3000);
+
+ /* Disable PHY MPLLA for eth mode change(after ECO) */
+ txgbe_wr32_ephy(hw, 0x4, 0x240A);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(20);
+
+ /* Set the eth change_mode bit first in mis_rst register */
+ /* for corresponding LAN port */
+ if (hw->bus.lan_id == 0)
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN0_CHG_ETH_MODE);
+ else
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN1_CHG_ETH_MODE);
+
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b01
+ * PCS_TYPE_SEL: non KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2,
+ TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X);
+
+ /* Set SR PMA MMD Control1 Register Bit[13] = 1'b0 SS13: 1G speed */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1,
+ TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_1G);
+
+ /* Set SR MII MMD Control Register to corresponding speed: {Bit[6],
+ * Bit[13]}=[2'b00,2'b01,2'b10]->[10M,100M,1G]
+ */
+ if (speed == TXGBE_LINK_SPEED_100_FULL)
+ wdata = 0x2100;
+ else if (speed == TXGBE_LINK_SPEED_1GB_FULL)
+ wdata = 0x0140;
+ else if (speed == TXGBE_LINK_SPEED_10_FULL)
+ wdata = 0x0100;
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_CTL, wdata);
+
+ value = (0xf5f0 & ~0x710) | (0x5 << 8) | 0x10;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+
+ for (i = 0; i < 4; i++) {
+ if (i != 0)
+ value = 0xff06;
+ else
+ value = (0x45 & ~0xFFFF) | (0x7 << 12) |
+ (0x7 << 8) | 0x6;
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0 + i, value);
+ }
+
+ value = 0x0 & ~0x7;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0);
+
+ value = (0x6db & ~0x7) | 0x4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, value);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 0 Register Bit[7:0] = 8'd32 MPLLA_MULTIPLIER
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0,
+ TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_1GBASEX_KX);
+
+ /* Set VR XS, PMA or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 3 Register Bit[10:0] = 11'd70 MPLLA_BANDWIDTH
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3,
+ TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_1GBASEX_KX);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Load 0 Register Bit[12:0] = 13'd1344 VCO_LD_VAL_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0,
+ TXGBE_PHY_VCO_CAL_LD0_1GBASEX_KX);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD1, 0x549);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD2, 0x549);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD3, 0x549);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Reference 0 Register Bit[5:0] = 6'd42 VCO_REF_LD_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0,
+ TXGBE_PHY_VCO_CAL_REF0_LD0_1GBASEX_KX);
+
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF1, 0x2929);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY AFE-DFE
+ * Enable Register Bit[4], Bit[0] = 1'b0 AFE_EN_0, DFE_EN_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, 0x0);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx
+ * Equalization Control 4 Register Bit[0] = 1'b0 CONT_ADAPT_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, 0x0010);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx Rate
+ * Control Register Bit[2:0] = 3'b011 TX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL,
+ TXGBE_PHY_TX_RATE_CTL_TX0_RATE_1GBASEX_KX);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx Rate
+ * Control Register Bit[2:0] = 3'b011 RX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL,
+ TXGBE_PHY_RX_RATE_CTL_RX0_RATE_1GBASEX_KX);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Tx General
+ * Control 2 Register Bit[9:8] = 2'b01 TX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2,
+ TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx General
+ * Control 2 Register Bit[9:8] = 2'b01 RX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2,
+ TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_OTHER);
+
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA Control
+ * 2 Register Bit[10:8] = 3'b010 MPLLA_DIV16P5_CLK_EN=0,
+ * MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2,
+ TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_10);
+
+ /* VR MII MMD AN Control Register Bit[8] = 1'b1 MII_CTRL */
+ /* Set to 8bit MII (required in 10M/100M SGMII) */
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x0100);
+
+ /* 10. Initialize the mode by setting VR XS or PCS MMD Digital Control1
+ * Register Bit[15](VR_RST)
+ */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+ /* wait phy initialization done */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ !(value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST),
+ 100000, 10000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1);
+ if (status == -ETIMEDOUT) {
+ txgbe_info(hw, "PHY initialization timeout.\n");
+ return;
+ }
+
+ /* if success, set link status */
+ hw->link_status = TXGBE_LINK_STATUS_KX;
+
+ txgbe_dbg(hw, "Set KX TX_EQ MAIN:24 PRE:4 POST:16\n");
+ /* 5. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL0 Register
+ * Bit[13:8](TX_EQ_MAIN) = 6'd30, Bit[5:0](TX_EQ_PRE) = 6'd4
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0);
+ value = (value & ~0x3F3F) | (24 << 8) | 4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0, value);
+ /* 6. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL1 Register
+ * Bit[6](TX_EQ_OVR_RIDE) = 1'b1, Bit[5:0](TX_EQ_POST) = 6'd36
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1);
+ value = (value & ~0x7F) | 16 | (1 << 6);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1, value);
+}
+
+static void txgbe_set_link_to_sfi(struct txgbe_hw *hw, u32 speed)
+{
+ int status = 0;
+ u32 value = 0;
+
+ /* Set the module link speed */
+ hw->mac.ops.set_rate_select_speed(hw, speed);
+
+ /* 1. Wait xpcs power-up good */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ (value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK) ==
+ TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD,
+ 10000, 1000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS);
+ if (status == -ETIMEDOUT) {
+ txgbe_info(hw, "xpcs power-up timeout.\n");
+ return;
+ }
+
+ wr32m(hw, TXGBE_MAC_TX_CFG, TXGBE_MAC_TX_CFG_TE, ~TXGBE_MAC_TX_CFG_TE);
+
+ /* 2. Disable xpcs AN-73 */
+ txgbe_wr32_epcs(hw, TXGBE_SR_AN_MMD_CTL, 0x0);
+
+ /* Disable PHY MPLLA for eth mode change(after ECO) */
+ txgbe_wr32_ephy(hw, 0x4, 0x243A);
+ TXGBE_WRITE_FLUSH(hw);
+ msleep(20);
+ /* Set the eth change_mode bit first in mis_rst register
+ * for corresponding LAN port
+ */
+ if (hw->bus.lan_id == 0)
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN0_CHG_ETH_MODE);
+ else
+ wr32(hw, TXGBE_MIS_RST,
+ TXGBE_MIS_RST_LAN1_CHG_ETH_MODE);
+
+ if (speed == TXGBE_LINK_SPEED_10GB_FULL) {
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b00
+ * PCS_TYPE_SEL: KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2, 0);
+ value = txgbe_rd32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1);
+ value = value | 0x2000;
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1, value);
+ /* Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL0 Register Bit[7:0] = 8'd33
+ * MPLLA_MULTIPLIER
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0, 0x0021);
+ /* 3. Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL3 Register
+ * Bit[10:0](MPLLA_BANDWIDTH) = 11'd0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3, 0);
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_GENCTRL1);
+ value = (value & ~0x700) | 0x500;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+ /* 4.Set VR_XS_PMA_Gen5_12G_MISC_CTRL0 Register
+ * Bit[12:8](RX_VREF_CTRL) = 5'hF
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+ /* Set VR_XS_PMA_Gen5_12G_VCO_CAL_LD0 Register
+ * Bit[12:0] = 13'd1353 VCO_LD_VAL_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0, 0x0549);
+ /* Set VR_XS_PMA_Gen5_12G_VCO_CAL_REF0 Register Bit[5:0] = 6'd41
+ * VCO_REF_LD_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0, 0x0029);
+ /* Set VR_XS_PMA_Gen5_12G_TX_RATE_CTRL Register
+ * Bit[2:0] = 3'b000 TX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL, 0);
+ /* Set VR_XS_PMA_Gen5_12G_RX_RATE_CTRL Register
+ * Bit[2:0] = 3'b000 RX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL, 0);
+ /* Set VR_XS_PMA_Gen5_12G_TX_GENCTRL2 Register Bit[9:8] = 2'b11
+ * TX0_WIDTH: 20bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2, 0x0300);
+ /* Set VR_XS_PMA_Gen5_12G_RX_GENCTRL2 Register Bit[9:8] = 2'b11
+ * RX0_WIDTH: 20bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2, 0x0300);
+ /* Set VR_XS_PMA_Gen5_12G_MPLLA_CTRL2 Register
+ * Bit[10:8] = 3'b110 MPLLA_DIV16P5_CLK_EN=1,
+ * MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2, 0x0600);
+
+ if (hw->phy.sfp_type == txgbe_sfp_type_da_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_da_cu_core1) {
+ /* 7. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register
+ * Bit[15:8](VGA1/2_GAIN_0) = 8'h77, Bit[7:5]
+ * (CTLE_POLE_0) = 3'h2, Bit[4:0](CTLE_BOOST_0) = 4'hF
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, 0x774F);
+ } else {
+ /* 7. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register
+ * Bit[15:8] (VGA1/2_GAIN_0) = 8'h00,
+ * Bit[7:5](CTLE_POLE_0) = 3'h2,
+ * Bit[4:0](CTLE_BOOST_0) = 4'hA
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0);
+ value = (value & ~0xFFFF) | (2 << 5) | 0x05;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, value);
+ }
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0);
+ value &= ~0x7;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+
+ if (hw->phy.sfp_type == txgbe_sfp_type_da_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_da_cu_core1) {
+ /* 8. Set VR_XS_PMA_Gen5_12G_DFE_TAP_CTRL0 Register
+ * Bit[7:0](DFE_TAP1_0) = 8'd20
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0014);
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE);
+ value = (value & ~0x11) | 0x11;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, value);
+ } else {
+ /* 8. Set VR_XS_PMA_Gen5_12G_DFE_TAP_CTRL0 Register
+ * Bit[7:0](DFE_TAP1_0) = 8'd20
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0xBE);
+ /* 9. Set VR_MII_Gen5_12G_AFE_DFE_EN_CTRL Register
+ * Bit[4](DFE_EN_0) = 1'b0, Bit[0](AFE_EN_0) = 1'b0
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE);
+ value = (value & ~0x11) | 0x0;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, value);
+ }
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_CTL);
+ value = value & ~0x1;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, value);
+ } else {
+ /* Set SR PCS Control2 Register Bits[1:0] = 2'b00
+ * PCS_TYPE_SEL: KR
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PCS_CTL2, 0x1);
+ /* Set SR PMA MMD Control1 Register Bit[13] = 1'b0
+ * SS13: 1G speed
+ */
+ txgbe_wr32_epcs(hw, TXGBE_SR_PMA_MMD_CTL1, 0x0000);
+ /* Set SR MII MMD Control Register to corresponding speed: */
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_CTL, 0x0140);
+
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_GENCTRL1);
+ value = (value & ~0x710) | 0x500;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GENCTRL1, value);
+ /* 4. Set VR_XS_PMA_Gen5_12G_MISC_CTRL0 Register
+ * Bit[12:8](RX_VREF_CTRL) = 5'hF
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MISC_CTL0, 0xCF00);
+ /* 5. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL0 Register
+ * Bit[13:8](TX_EQ_MAIN) = 6'd30, Bit[5:0](TX_EQ_PRE) = 6'd4
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0);
+ value = (value & ~0x3F3F) | (24 << 8) | 4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL0, value);
+ /* 6. Set VR_XS_PMA_Gen5_12G_TX_EQ_CTRL1 Register
+ * Bit[6](TX_EQ_OVR_RIDE) = 1'b1, Bit[5:0](TX_EQ_POST) = 6'd36
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1);
+ value = (value & ~0x7F) | 16 | (1 << 6);
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_EQ_CTL1, value);
+ if (hw->phy.sfp_type == txgbe_sfp_type_da_cu_core0 ||
+ hw->phy.sfp_type == txgbe_sfp_type_da_cu_core1) {
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, 0x774F);
+ } else {
+ /* 7. Set VR_XS_PMA_Gen5_12G_RX_EQ_CTRL0 Register
+ * Bit[15:8] (VGA1/2_GAIN_0) = 8'h00,
+ * Bit[7:5](CTLE_POLE_0) = 3'h2,
+ * Bit[4:0](CTLE_BOOST_0) = 4'hA
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0);
+ value = (value & ~0xFFFF) | 0x7706;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL0, value);
+ }
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0);
+ value = (value & ~0x7) | 0x0;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_ATT_LVL0, value);
+ /* 8. Set VR_XS_PMA_Gen5_12G_DFE_TAP_CTRL0 Register
+ * Bit[7:0](DFE_TAP1_0) = 8'd00
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_DFE_TAP_CTL0, 0x0);
+ /* Set VR_XS_PMA_Gen5_12G_RX_GENCTRL3 Register
+ * Bit[2:0] LOS_TRSHLD_0 = 4
+ */
+ value = txgbe_rd32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3);
+ value = (value & ~0x7) | 0x4;
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL3, value);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY
+ * MPLLA Control 0 Register Bit[7:0] = 8'd32 MPLLA_MULTIPLIER
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL0, 0x0020);
+ /* Set VR XS, PMA or MII Synopsys Enterprise Gen5 12G PHY MPLLA
+ * Control 3 Register Bit[10:0] = 11'd70 MPLLA_BANDWIDTH
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL3, 0x0046);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Load 0 Register
+ * Bit[12:0] = 13'd1344 VCO_LD_VAL_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_LD0, 0x0540);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY VCO
+ * Calibration Reference 0 Register
+ * Bit[5:0] = 6'd42 VCO_REF_LD_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_VCO_CAL_REF0, 0x002A);
+ /* Set VR XS, PMA, MII Synopsys Enterprise Gen5 12G PHY AFE-DFE
+ * Enable Register Bit[4], Bit[0] = 1'b0 AFE_EN_0, DFE_EN_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_AFE_DFE_ENABLE, 0x0);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY Rx
+ * Equalization Control 4 Register Bit[0] = 1'b0 CONT_ADAPT_0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_EQ_CTL, 0x0010);
+ /* Set VR XS, PMA, MII Synopsys Enterprise Gen5 12G PHY Tx Rate
+ * Control Register Bit[2:0] = 3'b011 TX0_RATE
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_RATE_CTL, 0x0003);
+ /* Set VR XS, PMA, MII Synopsys Enterprise Gen5 12G PHY Rx Rate
+ * Control Register Bit[2:0] = 3'b011
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_RATE_CTL, 0x0003);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY
+ * Tx General Control 2 Register
+ * Bit[9:8] = 2'b01 TX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_TX_GEN_CTL2, 0x0100);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY
+ * Rx General Control 2 Register
+ * Bit[9:8] = 2'b01 RX0_WIDTH: 10bits
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_RX_GEN_CTL2, 0x0100);
+ /* Set VR XS, PMA, or MII Synopsys Enterprise Gen5 12G PHY MPLLA
+ * Control 2 Register Bit[10:8] = 3'b010 MPLLA_DIV16P5_CLK_EN=0,
+ * MPLLA_DIV10_CLK_EN=1, MPLLA_DIV8_CLK_EN=0
+ */
+ txgbe_wr32_epcs(hw, TXGBE_PHY_MPLLA_CTL2, 0x0200);
+ /* VR MII MMD AN Control Register Bit[8] = 1'b1 MII_CTRL */
+ txgbe_wr32_epcs(hw, TXGBE_SR_MII_MMD_AN_CTL, 0x0100);
+ }
+ /* 10. Initialize the mode by setting VR XS or PCS MMD Digital Control1
+ * Register Bit[15](VR_RST)
+ */
+ txgbe_wr32_epcs(hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1, 0xA000);
+ /* wait phy initialization done */
+ status = read_poll_timeout(txgbe_rd32_epcs, value,
+ !(value & TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST),
+ 100000, 10000000, false,
+ hw, TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1);
+ if (status == -ETIMEDOUT)
+ txgbe_info(hw, "PHY initialization timeout.\n");
+}
+
+/**
+ * txgbe_setup_mac_link - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed.
+ **/
+int txgbe_setup_mac_link(struct txgbe_hw *hw,
+ u32 speed,
+ bool __maybe_unused autoneg_wait_to_complete)
+{
+ u32 link_capabilities = TXGBE_LINK_SPEED_UNKNOWN;
+ u32 link_speed = TXGBE_LINK_SPEED_UNKNOWN;
+ u16 sub_dev_id = hw->subsystem_device_id;
+ bool autoneg = false;
+ bool link_up = false;
+ int status = 0;
+
+ /* Check to see if speed passed in is supported. */
+ status = hw->mac.ops.get_link_capabilities(hw, &link_capabilities,
+ &autoneg);
+ if (status)
+ return status;
+
+ speed &= link_capabilities;
+
+ if (speed == TXGBE_LINK_SPEED_UNKNOWN)
+ return -EINVAL;
+
+ if (!(((sub_dev_id & TXGBE_DEV_MASK) == TXGBE_ID_KR_KX_KX4) ||
+ ((sub_dev_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_XAUI) ||
+ ((sub_dev_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_SGMII))) {
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_speed == speed && link_up)
+ return status;
+ }
+
+ if ((hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_KR_KX_KX4) {
+ if (!autoneg) {
+ switch (hw->phy.link_mode) {
+ case TXGBE_PHYSICAL_LAYER_10GBASE_KR:
+ txgbe_set_link_to_kr(hw, autoneg);
+ break;
+ case TXGBE_PHYSICAL_LAYER_10GBASE_KX4:
+ txgbe_set_link_to_kx4(hw, autoneg);
+ break;
+ case TXGBE_PHYSICAL_LAYER_1000BASE_KX:
+ txgbe_set_link_to_kx(hw, speed, autoneg);
+ break;
+ default:
+ return -ENODEV;
+ }
+ } else {
+ txgbe_set_link_to_kr(hw, autoneg);
+ }
+ } else if ((hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_XAUI ||
+ (hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_XAUI ||
+ (hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_SGMII ||
+ (hw->subsystem_device_id & TXGBE_DEV_MASK) == TXGBE_ID_MAC_SGMII) {
+ if (speed == TXGBE_LINK_SPEED_10GB_FULL) {
+ txgbe_set_link_to_kx4(hw, 0);
+ } else {
+ txgbe_set_link_to_kx(hw, speed, 0);
+ txgbe_set_sgmii_an37_ability(hw);
+ }
+ } else if (hw->phy.media_type == txgbe_media_type_fiber) {
+ txgbe_set_link_to_sfi(hw, speed);
+ if (speed == TXGBE_LINK_SPEED_1GB_FULL)
+ txgbe_set_sgmii_an37_ability(hw);
+ }
+
+ return status;
+}
+
void txgbe_reset_misc(struct txgbe_hw *hw)
{
+ u32 value;
int i;
txgbe_init_i2c(hw);
+ value = txgbe_rd32_epcs(hw, TXGBE_SR_PCS_CTL2);
+ if ((value & 0x3) != TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X)
+ hw->link_status = TXGBE_LINK_STATUS_NONE;
+
/* receive packets that size > 2048 */
wr32m(hw, TXGBE_MAC_RX_CFG,
TXGBE_MAC_RX_CFG_JE, TXGBE_MAC_RX_CFG_JE);
@@ -1752,3 +2928,53 @@ int txgbe_validate_eeprom_checksum(struct txgbe_hw *hw,
return status;
}
+
+/**
+ * txgbe_check_mac_link - Determine link and speed status
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @link_up: true when link is up
+ * @link_up_wait_to_complete: bool used to wait for link up or not
+ *
+ * Reads the links register to determine if link is up and the current speed
+ **/
+void txgbe_check_mac_link(struct txgbe_hw *hw, u32 *speed,
+ bool *link_up, bool link_up_wait_to_complete)
+{
+ u32 links_reg = 0;
+ u32 i;
+
+ if (link_up_wait_to_complete) {
+ for (i = 0; i < TXGBE_LINK_UP_TIME; i++) {
+ links_reg = rd32(hw, TXGBE_CFG_PORT_ST);
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_UP) {
+ *link_up = true;
+ break;
+ }
+ *link_up = false;
+ msleep(100);
+ }
+ } else {
+ links_reg = rd32(hw, TXGBE_CFG_PORT_ST);
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_UP)
+ *link_up = true;
+ else
+ *link_up = false;
+ }
+
+ if (*link_up) {
+ if ((links_reg & TXGBE_CFG_PORT_ST_LINK_10G) ==
+ TXGBE_CFG_PORT_ST_LINK_10G)
+ *speed = TXGBE_LINK_SPEED_10GB_FULL;
+ else if ((links_reg & TXGBE_CFG_PORT_ST_LINK_1G) ==
+ TXGBE_CFG_PORT_ST_LINK_1G)
+ *speed = TXGBE_LINK_SPEED_1GB_FULL;
+ else if ((links_reg & TXGBE_CFG_PORT_ST_LINK_100M) ==
+ TXGBE_CFG_PORT_ST_LINK_100M)
+ *speed = TXGBE_LINK_SPEED_100_FULL;
+ else
+ *speed = TXGBE_LINK_SPEED_10_FULL;
+ } else {
+ *speed = TXGBE_LINK_SPEED_UNKNOWN;
+ }
+}
@@ -54,9 +54,23 @@ bool txgbe_check_mng_access(struct txgbe_hw *hw);
void txgbe_init_thermal_sensor_thresh(struct txgbe_hw *hw);
void txgbe_disable_rx(struct txgbe_hw *hw);
+int txgbe_setup_mac_link_multispeed_fiber(struct txgbe_hw *hw,
+ u32 speed,
+ bool autoneg_wait_to_complete);
int txgbe_check_flash_load(struct txgbe_hw *hw, u32 check_bit);
+int txgbe_get_link_capabilities(struct txgbe_hw *hw,
+ u32 *speed, bool *autoneg);
enum txgbe_media_type txgbe_get_media_type(struct txgbe_hw *hw);
+void txgbe_disable_tx_laser_multispeed_fiber(struct txgbe_hw *hw);
+void txgbe_enable_tx_laser_multispeed_fiber(struct txgbe_hw *hw);
+void txgbe_flap_tx_laser_multispeed_fiber(struct txgbe_hw *hw);
+void txgbe_set_hard_rate_select_speed(struct txgbe_hw *hw, u32 speed);
+int txgbe_setup_mac_link(struct txgbe_hw *hw, u32 speed,
+ bool autoneg_wait_to_complete);
+void txgbe_check_mac_link(struct txgbe_hw *hw, u32 *speed,
+ bool *link_up, bool link_up_wait_to_complete);
+void txgbe_init_mac_link_ops(struct txgbe_hw *hw);
void txgbe_reset_misc(struct txgbe_hw *hw);
int txgbe_reset_hw(struct txgbe_hw *hw);
int txgbe_identify_phy(struct txgbe_hw *hw);
@@ -75,6 +89,10 @@ u32 txgbe_rd32_epcs(struct txgbe_hw *hw, u32 addr);
void txgbe_wr32_epcs(struct txgbe_hw *hw, u32 addr, u32 data);
void txgbe_wr32_ephy(struct txgbe_hw *hw, u32 addr, u32 data);
+void txgbe_set_link_to_kr(struct txgbe_hw *hw, bool autoneg);
+void txgbe_set_link_to_kx4(struct txgbe_hw *hw, bool autoneg);
+void txgbe_set_link_to_kx(struct txgbe_hw *hw, u32 speed, bool autoneg);
+
int txgbe_fmgr_cmd_op(struct txgbe_hw *hw, u32 cmd, u32 cmd_addr);
int txgbe_flash_read_dword(struct txgbe_hw *hw, u32 addr, u32 *data);
@@ -202,9 +202,71 @@ static bool txgbe_is_sfp(struct txgbe_hw *hw)
}
}
+static bool txgbe_is_backplane(struct txgbe_hw *hw)
+{
+ switch (hw->phy.media_type) {
+ case txgbe_media_type_backplane:
+ return true;
+ default:
+ return false;
+ }
+}
+
+/**
+ * txgbe_sfp_link_config - set up SFP+ link
+ * @adapter: pointer to private adapter struct
+ **/
+static void txgbe_sfp_link_config(struct txgbe_adapter *adapter)
+{
+ /* We are assuming the worst case scenerio here, and that
+ * is that an SFP was inserted/removed after the reset
+ * but before SFP detection was enabled. As such the best
+ * solution is to just start searching as soon as we start
+ */
+
+ adapter->flags2 |= TXGBE_FLAG2_SFP_NEEDS_RESET;
+ adapter->sfp_poll_time = 0;
+}
+
static void txgbe_up_complete(struct txgbe_adapter *adapter)
{
+ struct txgbe_hw *hw = &adapter->hw;
+ u32 links_reg;
+
txgbe_get_hw_control(adapter);
+
+ /* enable the optics for SFP+ fiber */
+ hw->mac.ops.enable_tx_laser(hw);
+
+ /* make sure to complete pre-operations */
+ smp_mb__before_atomic();
+ clear_bit(__TXGBE_DOWN, &adapter->state);
+
+ if (txgbe_is_sfp(hw)) {
+ txgbe_sfp_link_config(adapter);
+ } else if (txgbe_is_backplane(hw)) {
+ adapter->flags |= TXGBE_FLAG_NEED_LINK_CONFIG;
+ txgbe_service_event_schedule(adapter);
+ }
+
+ links_reg = rd32(hw, TXGBE_CFG_PORT_ST);
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_UP) {
+ if (links_reg & TXGBE_CFG_PORT_ST_LINK_10G) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) |
+ TXGBE_MAC_TX_CFG_SPEED_10G);
+ } else if (links_reg & (TXGBE_CFG_PORT_ST_LINK_1G | TXGBE_CFG_PORT_ST_LINK_100M)) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) |
+ TXGBE_MAC_TX_CFG_SPEED_1G);
+ }
+ }
+
+ /* Set PF Reset Done bit so PF/VF Mail Ops can work */
+ wr32m(hw, TXGBE_CFG_PORT_CTL,
+ TXGBE_CFG_PORT_CTL_PFRSTD, TXGBE_CFG_PORT_CTL_PFRSTD);
}
void txgbe_reset(struct txgbe_adapter *adapter)
@@ -214,12 +276,21 @@ void txgbe_reset(struct txgbe_adapter *adapter)
u8 old_addr[ETH_ALEN];
int err;
+ /* lock SFP init bit to prevent race conditions with the watchdog */
+ while (test_and_set_bit(__TXGBE_IN_SFP_INIT, &adapter->state))
+ usleep_range(1000, 2000);
+
+ /* clear all SFP and link config related flags while holding SFP_INIT */
+ adapter->flags2 &= ~TXGBE_FLAG2_SFP_NEEDS_RESET;
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_CONFIG;
+
err = hw->mac.ops.init_hw(hw);
if (err != 0 &&
hw->phy.sfp_type != txgbe_sfp_type_not_present &&
hw->phy.type != txgbe_phy_sfp_unsupported)
dev_err(&adapter->pdev->dev, "Hardware Error: %d\n", err);
+ clear_bit(__TXGBE_IN_SFP_INIT, &adapter->state);
/* do not flush user set addresses */
memcpy(old_addr, &adapter->mac_table[0].addr, netdev->addr_len);
txgbe_flush_sw_mac_table(adapter);
@@ -246,6 +317,8 @@ void txgbe_disable_device(struct txgbe_adapter *adapter)
netif_carrier_off(netdev);
netif_tx_disable(netdev);
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_UPDATE;
+
del_timer_sync(&adapter->service_timer);
if (hw->bus.lan_id == 0)
@@ -275,8 +348,14 @@ void txgbe_disable_device(struct txgbe_adapter *adapter)
void txgbe_down(struct txgbe_adapter *adapter)
{
+ struct txgbe_hw *hw = &adapter->hw;
+
txgbe_disable_device(adapter);
txgbe_reset(adapter);
+
+ if (!(((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP)))
+ /* power down the optics for SFP+ fiber */
+ hw->mac.ops.disable_tx_laser(hw);
}
/**
@@ -357,7 +436,11 @@ int txgbe_open(struct net_device *netdev)
*/
static void txgbe_close_suspend(struct txgbe_adapter *adapter)
{
+ struct txgbe_hw *hw = &adapter->hw;
+
txgbe_disable_device(adapter);
+ if (!((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP))
+ hw->mac.ops.disable_tx_laser(hw);
}
/**
@@ -412,12 +495,260 @@ static void txgbe_shutdown(struct pci_dev *pdev)
}
}
+/**
+ * txgbe_watchdog_update_link - update the link status
+ * @adapter: pointer to the device adapter structure
+ **/
+static void txgbe_watchdog_update_link(struct txgbe_adapter *adapter)
+{
+ u32 link_speed = adapter->link_speed;
+ struct txgbe_hw *hw = &adapter->hw;
+ bool link_up = adapter->link_up;
+ u32 i = 1, reg;
+
+ if (!(adapter->flags & TXGBE_FLAG_NEED_LINK_UPDATE))
+ return;
+
+ link_speed = TXGBE_LINK_SPEED_10GB_FULL;
+ link_up = true;
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+
+ if (link_up || time_after(jiffies, (adapter->link_check_timeout +
+ TXGBE_TRY_LINK_TIMEOUT))) {
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_UPDATE;
+ }
+
+ for (i = 0; i < 3; i++) {
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ msleep(20);
+ }
+
+ adapter->link_up = link_up;
+ adapter->link_speed = link_speed;
+
+ if (link_up) {
+ if (link_speed & TXGBE_LINK_SPEED_10GB_FULL) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) | TXGBE_MAC_TX_CFG_TE |
+ TXGBE_MAC_TX_CFG_SPEED_10G);
+ } else if (link_speed & (TXGBE_LINK_SPEED_1GB_FULL |
+ TXGBE_LINK_SPEED_100_FULL | TXGBE_LINK_SPEED_10_FULL)) {
+ wr32(hw, TXGBE_MAC_TX_CFG,
+ (rd32(hw, TXGBE_MAC_TX_CFG) &
+ ~TXGBE_MAC_TX_CFG_SPEED_MASK) | TXGBE_MAC_TX_CFG_TE |
+ TXGBE_MAC_TX_CFG_SPEED_1G);
+ }
+
+ /* Re configure MAC RX */
+ reg = rd32(hw, TXGBE_MAC_RX_CFG);
+ wr32(hw, TXGBE_MAC_RX_CFG, reg);
+ wr32(hw, TXGBE_MAC_PKT_FLT, TXGBE_MAC_PKT_FLT_PR);
+ reg = rd32(hw, TXGBE_MAC_WDG_TIMEOUT);
+ wr32(hw, TXGBE_MAC_WDG_TIMEOUT, reg);
+ }
+}
+
+/**
+ * txgbe_watchdog_link_is_up - update netif_carrier status and
+ * print link up message
+ * @adapter: pointer to the device adapter structure
+ **/
+static void txgbe_watchdog_link_is_up(struct txgbe_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ u32 link_speed = adapter->link_speed;
+ const char *speed_str;
+
+ /* only continue if link was previously down */
+ if (netif_carrier_ok(netdev))
+ return;
+
+ switch (link_speed) {
+ case TXGBE_LINK_SPEED_10GB_FULL:
+ speed_str = "10 Gbps";
+ break;
+ case TXGBE_LINK_SPEED_1GB_FULL:
+ speed_str = "1 Gbps";
+ break;
+ case TXGBE_LINK_SPEED_100_FULL:
+ speed_str = "100 Mbps";
+ break;
+ case TXGBE_LINK_SPEED_10_FULL:
+ speed_str = "10 Mbps";
+ break;
+ default:
+ speed_str = "unknown speed";
+ break;
+ }
+
+ netif_info(adapter, drv, netdev,
+ "NIC Link is Up %s\n", speed_str);
+
+ netif_carrier_on(netdev);
+}
+
+/**
+ * txgbe_watchdog_link_is_down - update netif_carrier status and
+ * print link down message
+ * @adapter: pointer to the adapter structure
+ **/
+static void txgbe_watchdog_link_is_down(struct txgbe_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ adapter->link_up = false;
+ adapter->link_speed = 0;
+
+ /* only continue if link was up previously */
+ if (!netif_carrier_ok(netdev))
+ return;
+
+ netif_info(adapter, drv, netdev, "NIC Link is Down\n");
+ netif_carrier_off(netdev);
+}
+
+/**
+ * txgbe_watchdog_subtask - check and bring link up
+ * @adapter: pointer to the device adapter structure
+ **/
+static void txgbe_watchdog_subtask(struct txgbe_adapter *adapter)
+{
+ /* if interface is down do nothing */
+ if (test_bit(__TXGBE_DOWN, &adapter->state) ||
+ test_bit(__TXGBE_REMOVING, &adapter->state) ||
+ test_bit(__TXGBE_RESETTING, &adapter->state))
+ return;
+
+ txgbe_watchdog_update_link(adapter);
+
+ if (adapter->link_up)
+ txgbe_watchdog_link_is_up(adapter);
+ else
+ txgbe_watchdog_link_is_down(adapter);
+}
+
+/**
+ * txgbe_sfp_detection_subtask - poll for SFP+ cable
+ * @adapter: the txgbe adapter structure
+ **/
+static void txgbe_sfp_detection_subtask(struct txgbe_adapter *adapter)
+{
+ struct txgbe_hw *hw = &adapter->hw;
+ struct txgbe_mac_info *mac = &hw->mac;
+ int err;
+
+ /* not searching for SFP so there is nothing to do here */
+ if (!(adapter->flags2 & TXGBE_FLAG2_SFP_NEEDS_RESET))
+ return;
+
+ if (adapter->sfp_poll_time &&
+ time_after(adapter->sfp_poll_time, jiffies))
+ return; /* If not yet time to poll for SFP */
+
+ /* someone else is in init, wait until next service event */
+ if (test_and_set_bit(__TXGBE_IN_SFP_INIT, &adapter->state))
+ return;
+
+ adapter->sfp_poll_time = jiffies + TXGBE_SFP_POLL_JIFFIES - 1;
+
+ err = hw->phy.ops.identify_sfp(hw);
+ if (err != 0) {
+ if (hw->phy.sfp_type == txgbe_sfp_type_not_present) {
+ /* If no cable is present, then we need to reset
+ * the next time we find a good cable.
+ */
+ adapter->flags2 |= TXGBE_FLAG2_SFP_NEEDS_RESET;
+ }
+ /* exit on error */
+ goto sfp_out;
+ }
+
+ /* exit if reset not needed */
+ if (!(adapter->flags2 & TXGBE_FLAG2_SFP_NEEDS_RESET))
+ goto sfp_out;
+
+ adapter->flags2 &= ~TXGBE_FLAG2_SFP_NEEDS_RESET;
+
+ if (hw->phy.multispeed_fiber) {
+ /* Set up dual speed SFP+ support */
+ mac->ops.setup_link = txgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_mac_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ } else {
+ mac->ops.setup_link = txgbe_setup_mac_link;
+ mac->ops.set_rate_select_speed = txgbe_set_hard_rate_select_speed;
+ hw->phy.autoneg_advertised = 0;
+ }
+
+ adapter->flags |= TXGBE_FLAG_NEED_LINK_CONFIG;
+ netif_info(adapter, probe, adapter->netdev,
+ "detected SFP+: %d\n", hw->phy.sfp_type);
+
+sfp_out:
+ clear_bit(__TXGBE_IN_SFP_INIT, &adapter->state);
+
+ if (hw->phy.type == txgbe_phy_sfp_unsupported && adapter->netdev_registered)
+ dev_err(&adapter->pdev->dev,
+ "failed to initialize because an unsupported SFP+ module type was detected.\n");
+}
+
+/**
+ * txgbe_sfp_link_config_subtask - set up link SFP after module install
+ * @adapter: the txgbe adapter structure
+ **/
+static void txgbe_sfp_link_config_subtask(struct txgbe_adapter *adapter)
+{
+ struct txgbe_hw *hw = &adapter->hw;
+ u8 device_type = hw->subsystem_device_id & 0xF0;
+ bool autoneg = false;
+ u32 speed;
+
+ if (!(adapter->flags & TXGBE_FLAG_NEED_LINK_CONFIG))
+ return;
+
+ /* someone else is in init, wait until next service event */
+ if (test_and_set_bit(__TXGBE_IN_SFP_INIT, &adapter->state))
+ return;
+
+ adapter->flags &= ~TXGBE_FLAG_NEED_LINK_CONFIG;
+
+ if (device_type == TXGBE_ID_MAC_SGMII) {
+ speed = TXGBE_LINK_SPEED_1GB_FULL;
+ } else {
+ speed = hw->phy.autoneg_advertised;
+ if (!speed) {
+ hw->mac.ops.get_link_capabilities(hw, &speed, &autoneg);
+ /* setup the highest link when no autoneg */
+ if (!autoneg) {
+ if (speed & TXGBE_LINK_SPEED_10GB_FULL)
+ speed = TXGBE_LINK_SPEED_10GB_FULL;
+ }
+ }
+ }
+
+ hw->mac.ops.setup_link(hw, speed, false);
+
+ adapter->flags |= TXGBE_FLAG_NEED_LINK_UPDATE;
+ adapter->link_check_timeout = jiffies;
+ clear_bit(__TXGBE_IN_SFP_INIT, &adapter->state);
+}
+
static void txgbe_service_timer(struct timer_list *t)
{
struct txgbe_adapter *adapter = from_timer(adapter, t, service_timer);
+ struct txgbe_hw *hw = &adapter->hw;
unsigned long next_event_offset;
- next_event_offset = HZ * 2;
+ /* poll faster when waiting for link */
+ if (adapter->flags & TXGBE_FLAG_NEED_LINK_UPDATE) {
+ if ((hw->subsystem_device_id & 0xF0) == TXGBE_ID_KR_KX_KX4)
+ next_event_offset = HZ;
+ else
+ next_event_offset = HZ / 10;
+ } else {
+ next_event_offset = HZ * 2;
+ }
/* Reset the timer */
mod_timer(&adapter->service_timer, next_event_offset + jiffies);
@@ -435,6 +766,10 @@ static void txgbe_service_task(struct work_struct *work)
struct txgbe_adapter,
service_task);
+ txgbe_sfp_detection_subtask(adapter);
+ txgbe_sfp_link_config_subtask(adapter);
+ txgbe_watchdog_subtask(adapter);
+
txgbe_service_event_complete(adapter);
}
@@ -706,6 +1041,10 @@ static int txgbe_probe(struct pci_dev *pdev,
pci_set_drvdata(pdev, adapter);
adapter->netdev_registered = true;
+ if (!((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP))
+ /* power down the optics for SFP+ fiber */
+ hw->mac.ops.disable_tx_laser(hw);
+
/* carrier off reporting is important to ethtool even BEFORE open */
netif_carrier_off(netdev);
@@ -723,6 +1062,11 @@ static int txgbe_probe(struct pci_dev *pdev,
else
dev_warn(&pdev->dev, "Failed to enumerate PF devices.\n");
+ if ((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP)
+ netif_info(adapter, probe, netdev, "NCSI : support");
+ else
+ netif_info(adapter, probe, netdev, "NCSI : unsupported");
+
/* First try to read PBA as a string */
err = txgbe_read_pba_string(hw, part_str, TXGBE_PBANUM_LENGTH);
if (err)
@@ -749,6 +1093,15 @@ static int txgbe_probe(struct pci_dev *pdev,
if (err)
goto err_free_mac_table;
+ netif_info(adapter, probe, netdev,
+ "WangXun(R) 10 Gigabit Network Connection\n");
+
+ /* setup link for SFP devices with MNG FW, else wait for TXGBE_UP */
+ if (txgbe_mng_present(hw) && txgbe_is_sfp(hw) &&
+ ((hw->subsystem_device_id & TXGBE_NCSI_MASK) == TXGBE_NCSI_SUP))
+ hw->mac.ops.setup_link(hw, TXGBE_LINK_SPEED_10GB_FULL |
+ TXGBE_LINK_SPEED_1GB_FULL, true);
+
return 0;
err_release_hw:
@@ -60,6 +60,14 @@
#define TXGBE_SR_XS_PCS_MMD_STATUS1 0x30001
#define TXGBE_SR_PCS_CTL2 0x30007
#define TXGBE_SR_PMA_MMD_CTL1 0x10000
+#define TXGBE_SR_MII_MMD_CTL 0x1F0000
+#define TXGBE_SR_MII_MMD_DIGI_CTL 0x1F8000
+#define TXGBE_SR_MII_MMD_AN_CTL 0x1F8001
+#define TXGBE_SR_MII_MMD_AN_ADV 0x1F0004
+#define TXGBE_SR_MII_MMD_AN_ADV_PAUSE(_v) ((0x3 & (_v)) << 7)
+#define TXGBE_SR_MII_MMD_AN_ADV_PAUSE_ASM 0x80
+#define TXGBE_SR_MII_MMD_AN_ADV_PAUSE_SYM 0x100
+#define TXGBE_SR_MII_MMD_LP_BABL 0x1F0005
#define TXGBE_SR_AN_MMD_CTL 0x70000
#define TXGBE_SR_AN_MMD_ADV_REG1 0x70010
#define TXGBE_SR_AN_MMD_ADV_REG1_PAUSE(_v) ((0x3 & (_v)) << 10)
@@ -70,10 +78,124 @@
#define TXGBE_VR_AN_KR_MODE_CL 0x78003
#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1 0x38000
#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS 0x38010
+#define TXGBE_PHY_MPLLA_CTL0 0x18071
+#define TXGBE_PHY_MPLLA_CTL3 0x18077
+#define TXGBE_PHY_MISC_CTL0 0x18090
+#define TXGBE_PHY_VCO_CAL_LD0 0x18092
+#define TXGBE_PHY_VCO_CAL_LD1 0x18093
+#define TXGBE_PHY_VCO_CAL_LD2 0x18094
+#define TXGBE_PHY_VCO_CAL_LD3 0x18095
+#define TXGBE_PHY_VCO_CAL_REF0 0x18096
+#define TXGBE_PHY_VCO_CAL_REF1 0x18097
+#define TXGBE_PHY_RX_AD_ACK 0x18098
+#define TXGBE_PHY_AFE_DFE_ENABLE 0x1805D
+#define TXGBE_PHY_DFE_TAP_CTL0 0x1805E
+#define TXGBE_PHY_RX_EQ_ATT_LVL0 0x18057
+#define TXGBE_PHY_RX_EQ_CTL0 0x18058
+#define TXGBE_PHY_RX_EQ_CTL 0x1805C
+#define TXGBE_PHY_TX_EQ_CTL0 0x18036
+#define TXGBE_PHY_TX_EQ_CTL1 0x18037
+#define TXGBE_PHY_TX_RATE_CTL 0x18034
+#define TXGBE_PHY_RX_RATE_CTL 0x18054
+#define TXGBE_PHY_TX_GEN_CTL2 0x18032
+#define TXGBE_PHY_RX_GEN_CTL2 0x18052
+#define TXGBE_PHY_RX_GEN_CTL3 0x18053
+#define TXGBE_PHY_MPLLA_CTL2 0x18073
+#define TXGBE_PHY_RX_POWER_ST_CTL 0x18055
+#define TXGBE_PHY_TX_POWER_ST_CTL 0x18035
+#define TXGBE_PHY_TX_GENCTRL1 0x18031
#define TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_R 0x0
#define TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_X 0x1
#define TXGBE_SR_PCS_CTL2_PCS_TYPE_SEL_MASK 0x3
+#define TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_1G 0x0
+#define TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_10G 0x2000
+#define TXGBE_SR_PMA_MMD_CTL1_SPEED_SEL_MASK 0x2000
+#define TXGBE_SR_PMA_MMD_CTL1_LB_EN 0x1
+#define TXGBE_SR_MII_MMD_CTL_AN_EN 0x1000
+#define TXGBE_SR_MII_MMD_CTL_RESTART_AN 0x0200
+#define TXGBE_SR_AN_MMD_CTL_RESTART_AN 0x0200
+#define TXGBE_SR_AN_MMD_CTL_ENABLE 0x1000
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX4 0x40
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KX 0x20
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_KR 0x80
+#define TXGBE_SR_AN_MMD_ADV_REG2_BP_TYPE_MASK 0xFFFF
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_ENABLE 0x1000
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_CTL1_VR_RST 0x8000
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_MASK 0x1C
+#define TXGBE_VR_XS_OR_PCS_MMD_DIGI_STATUS_PSEQ_POWER_GOOD 0x10
+
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_1GBASEX_KX 32
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_10GBASER_KR 33
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_OTHER 40
+#define TXGBE_PHY_MPLLA_CTL0_MULTIPLIER_MASK 0xFF
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_1GBASEX_KX 0x56
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_10GBASER_KR 0x7B
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_OTHER 0x56
+#define TXGBE_PHY_MPLLA_CTL3_MULTIPLIER_BW_MASK 0x7FF
+#define TXGBE_PHY_MISC_CTL0_TX2RX_LB_EN_0 0x1
+#define TXGBE_PHY_MISC_CTL0_TX2RX_LB_EN_3_1 0xE
+#define TXGBE_PHY_MISC_CTL0_RX_VREF_CTRL 0x1F00
+#define TXGBE_PHY_VCO_CAL_LD0_1GBASEX_KX 1344
+#define TXGBE_PHY_VCO_CAL_LD0_10GBASER_KR 1353
+#define TXGBE_PHY_VCO_CAL_LD0_OTHER 1360
+#define TXGBE_PHY_VCO_CAL_LD0_MASK 0x1000
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_1GBASEX_KX 42
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_10GBASER_KR 41
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_OTHER 34
+#define TXGBE_PHY_VCO_CAL_REF0_LD0_MASK 0x3F
+#define TXGBE_PHY_AFE_DFE_ENABLE_DFE_EN0 0x10
+#define TXGBE_PHY_AFE_DFE_ENABLE_AFE_EN0 0x1
+#define TXGBE_PHY_AFE_DFE_ENABLE_MASK 0xFF
+#define TXGBE_PHY_RX_EQ_CTL_CONT_ADAPT0 0x1
+#define TXGBE_PHY_RX_EQ_CTL_CONT_ADAPT_MASK 0xF
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_10GBASER_KR 0x0
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_RXAUI 0x1
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_1GBASEX_KX 0x3
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_OTHER 0x2
+#define TXGBE_PHY_TX_RATE_CTL_TX1_RATE_OTHER 0x20
+#define TXGBE_PHY_TX_RATE_CTL_TX2_RATE_OTHER 0x200
+#define TXGBE_PHY_TX_RATE_CTL_TX3_RATE_OTHER 0x2000
+#define TXGBE_PHY_TX_RATE_CTL_TX0_RATE_MASK 0x7
+#define TXGBE_PHY_TX_RATE_CTL_TX1_RATE_MASK 0x70
+#define TXGBE_PHY_TX_RATE_CTL_TX2_RATE_MASK 0x700
+#define TXGBE_PHY_TX_RATE_CTL_TX3_RATE_MASK 0x7000
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_10GBASER_KR 0x0
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_RXAUI 0x1
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_1GBASEX_KX 0x3
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_OTHER 0x2
+#define TXGBE_PHY_RX_RATE_CTL_RX1_RATE_OTHER 0x20
+#define TXGBE_PHY_RX_RATE_CTL_RX2_RATE_OTHER 0x200
+#define TXGBE_PHY_RX_RATE_CTL_RX3_RATE_OTHER 0x2000
+#define TXGBE_PHY_RX_RATE_CTL_RX0_RATE_MASK 0x7
+#define TXGBE_PHY_RX_RATE_CTL_RX1_RATE_MASK 0x70
+#define TXGBE_PHY_RX_RATE_CTL_RX2_RATE_MASK 0x700
+#define TXGBE_PHY_RX_RATE_CTL_RX3_RATE_MASK 0x7000
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_10GBASER_KR 0x200
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_10GBASER_KR_RXAUI 0x300
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_OTHER 0x100
+#define TXGBE_PHY_TX_GEN_CTL2_TX0_WIDTH_MASK 0x300
+#define TXGBE_PHY_TX_GEN_CTL2_TX1_WIDTH_OTHER 0x400
+#define TXGBE_PHY_TX_GEN_CTL2_TX1_WIDTH_MASK 0xC00
+#define TXGBE_PHY_TX_GEN_CTL2_TX2_WIDTH_OTHER 0x1000
+#define TXGBE_PHY_TX_GEN_CTL2_TX2_WIDTH_MASK 0x3000
+#define TXGBE_PHY_TX_GEN_CTL2_TX3_WIDTH_OTHER 0x4000
+#define TXGBE_PHY_TX_GEN_CTL2_TX3_WIDTH_MASK 0xC000
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_10GBASER_KR 0x200
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_10GBASER_KR_RXAUI 0x300
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_OTHER 0x100
+#define TXGBE_PHY_RX_GEN_CTL2_RX0_WIDTH_MASK 0x300
+#define TXGBE_PHY_RX_GEN_CTL2_RX1_WIDTH_OTHER 0x400
+#define TXGBE_PHY_RX_GEN_CTL2_RX1_WIDTH_MASK 0xC00
+#define TXGBE_PHY_RX_GEN_CTL2_RX2_WIDTH_OTHER 0x1000
+#define TXGBE_PHY_RX_GEN_CTL2_RX2_WIDTH_MASK 0x3000
+#define TXGBE_PHY_RX_GEN_CTL2_RX3_WIDTH_OTHER 0x4000
+#define TXGBE_PHY_RX_GEN_CTL2_RX3_WIDTH_MASK 0xC000
+
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_8 0x100
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_10 0x200
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_16P5 0x400
+#define TXGBE_PHY_MPLLA_CTL2_DIV_CLK_EN_MASK 0x700
/**************** Global Registers ****************************/
/* chip control Registers */
@@ -277,6 +399,27 @@ struct txgbe_thermal_sensor_data {
#define TXGBE_CFG_PORT_ST_LAN_ID(_r) ((0x00000100U & (_r)) >> 8)
#define TXGBE_LINK_UP_TIME 90
+/* GPIO Registers */
+#define TXGBE_GPIO_DR 0x14800
+#define TXGBE_GPIO_DDR 0x14804
+/*GPIO bit */
+#define TXGBE_GPIO_DR_0 0x00000001U /* SDP0 Data Value */
+#define TXGBE_GPIO_DR_1 0x00000002U /* SDP1 Data Value */
+#define TXGBE_GPIO_DR_2 0x00000004U /* SDP2 Data Value */
+#define TXGBE_GPIO_DR_3 0x00000008U /* SDP3 Data Value */
+#define TXGBE_GPIO_DR_4 0x00000010U /* SDP4 Data Value */
+#define TXGBE_GPIO_DR_5 0x00000020U /* SDP5 Data Value */
+#define TXGBE_GPIO_DR_6 0x00000040U /* SDP6 Data Value */
+#define TXGBE_GPIO_DR_7 0x00000080U /* SDP7 Data Value */
+#define TXGBE_GPIO_DDR_0 0x00000001U /* SDP0 IO direction */
+#define TXGBE_GPIO_DDR_1 0x00000002U /* SDP1 IO direction */
+#define TXGBE_GPIO_DDR_2 0x00000004U /* SDP1 IO direction */
+#define TXGBE_GPIO_DDR_3 0x00000008U /* SDP3 IO direction */
+#define TXGBE_GPIO_DDR_4 0x00000010U /* SDP4 IO direction */
+#define TXGBE_GPIO_DDR_5 0x00000020U /* SDP5 IO direction */
+#define TXGBE_GPIO_DDR_6 0x00000040U /* SDP6 IO direction */
+#define TXGBE_GPIO_DDR_7 0x00000080U /* SDP7 IO direction */
+
/*********************** Transmit DMA registers **************************/
/* transmit global control */
#define TXGBE_TDM_CTL 0x18000
@@ -622,6 +765,38 @@ struct txgbe_hic_reset {
/* Number of 80 microseconds we wait for PCI Express master disable */
#define TXGBE_PCI_MASTER_DISABLE_TIMEOUT 80000
+
+/* Autonegotiation advertised speeds */
+typedef u32 txgbe_autoneg_advertised;
+/* Link speed */
+#define TXGBE_LINK_SPEED_UNKNOWN 0
+#define TXGBE_LINK_SPEED_100_FULL 1
+#define TXGBE_LINK_SPEED_1GB_FULL 2
+#define TXGBE_LINK_SPEED_10GB_FULL 4
+#define TXGBE_LINK_SPEED_10_FULL 8
+#define TXGBE_LINK_SPEED_AUTONEG (TXGBE_LINK_SPEED_100_FULL | \
+ TXGBE_LINK_SPEED_1GB_FULL | \
+ TXGBE_LINK_SPEED_10GB_FULL | \
+ TXGBE_LINK_SPEED_10_FULL)
+
+/* Physical layer type */
+typedef u32 txgbe_physical_layer;
+#define TXGBE_PHYSICAL_LAYER_UNKNOWN 0
+#define TXGBE_PHYSICAL_LAYER_10GBASE_T 0x0001
+#define TXGBE_PHYSICAL_LAYER_1000BASE_T 0x0002
+#define TXGBE_PHYSICAL_LAYER_100BASE_TX 0x0004
+#define TXGBE_PHYSICAL_LAYER_SFP_PLUS_CU 0x0008
+#define TXGBE_PHYSICAL_LAYER_10GBASE_LR 0x0010
+#define TXGBE_PHYSICAL_LAYER_10GBASE_LRM 0x0020
+#define TXGBE_PHYSICAL_LAYER_10GBASE_SR 0x0040
+#define TXGBE_PHYSICAL_LAYER_10GBASE_KX4 0x0080
+#define TXGBE_PHYSICAL_LAYER_1000BASE_KX 0x0200
+#define TXGBE_PHYSICAL_LAYER_1000BASE_BX 0x0400
+#define TXGBE_PHYSICAL_LAYER_10GBASE_KR 0x0800
+#define TXGBE_PHYSICAL_LAYER_10GBASE_XAUI 0x1000
+#define TXGBE_PHYSICAL_LAYER_SFP_ACTIVE_DA 0x2000
+#define TXGBE_PHYSICAL_LAYER_1000BASE_SX 0x4000
+
enum txgbe_eeprom_type {
txgbe_eeprom_uninitialized = 0,
txgbe_eeprom_spi,
@@ -730,6 +905,20 @@ struct txgbe_mac_operations {
int (*acquire_swfw_sync)(struct txgbe_hw *hw, u32 mask);
void (*release_swfw_sync)(struct txgbe_hw *hw, u32 mask);
+ /* Link */
+ void (*disable_tx_laser)(struct txgbe_hw *hw);
+ void (*enable_tx_laser)(struct txgbe_hw *hw);
+ void (*flap_tx_laser)(struct txgbe_hw *hw);
+ int (*setup_link)(struct txgbe_hw *hw, u32 speed,
+ bool autoneg_wait_to_complete);
+ int (*setup_mac_link)(struct txgbe_hw *hw, u32 speed,
+ bool autoneg_wait_to_complete);
+ void (*check_link)(struct txgbe_hw *hw, u32 *speed,
+ bool *link_up, bool link_up_wait_to_complete);
+ int (*get_link_capabilities)(struct txgbe_hw *hw, u32 *speed,
+ bool *autoneg);
+ void (*set_rate_select_speed)(struct txgbe_hw *hw, u32 speed);
+
/* RAR */
void (*set_rar)(struct txgbe_hw *hw, u32 index, u8 *addr, u64 pools,
u32 enable_addr);
@@ -796,7 +985,9 @@ struct txgbe_phy_info {
enum txgbe_sfp_type sfp_type;
enum txgbe_media_type media_type;
u32 phy_semaphore_mask;
+ txgbe_autoneg_advertised autoneg_advertised;
bool multispeed_fiber;
+ txgbe_physical_layer link_mode;
};
enum txgbe_reset_type {
@@ -805,6 +996,12 @@ enum txgbe_reset_type {
TXGBE_GLOBAL_RESET
};
+enum txgbe_link_status {
+ TXGBE_LINK_STATUS_NONE = 0,
+ TXGBE_LINK_STATUS_KX,
+ TXGBE_LINK_STATUS_KX4
+};
+
struct txgbe_hw {
u8 __iomem *hw_addr;
struct txgbe_mac_info mac;
@@ -819,6 +1016,7 @@ struct txgbe_hw {
u8 revision_id;
bool adapter_stopped;
enum txgbe_reset_type reset_type;
+ enum txgbe_link_status link_status;
u16 oem_ssid;
u16 oem_svid;
};
Get link capabilities, setup MAC and PHY link, and support to enable or disable Tx laser. Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> --- .../device_drivers/ethernet/wangxun/txgbe.rst | 5 + drivers/net/ethernet/wangxun/txgbe/txgbe.h | 25 + .../net/ethernet/wangxun/txgbe/txgbe_dummy.h | 47 + drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c | 1232 ++++++++++++++++- drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h | 18 + .../net/ethernet/wangxun/txgbe/txgbe_main.c | 355 ++++- .../net/ethernet/wangxun/txgbe/txgbe_type.h | 198 +++ 7 files changed, 1876 insertions(+), 4 deletions(-)