[net-next,v3,4/5] net: phy: Add dts support for Motorcomm yt8531s gigabit ethernet phy

Commit Message

Frank Sae Jan. 30, 2023, 6:35 a.m. UTC

Add dts support for Motorcomm yt8531s gigabit ethernet phy.
 Change yt8521_probe to support clk config of yt8531s. Becase
 yt8521_probe does the things which yt8531s is needed, so
 removed yt8531s function.
 This patch has been verified on AM335x platform with yt8531s board.

Signed-off-by: Frank Sae <[e-mail]>
Reviewed-by: Andrew Lunn <[e-mail]>
---
 drivers/net/phy/motorcomm.c | 51 ++++++++++++++++++++-----------------
 1 file changed, 27 insertions(+), 24 deletions(-)

Patch

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 4a5ca846adeb..ee9cd72758d6 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -258,8 +258,6 @@ 
 #define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL	3
 #define YT8531_SCR_CLK_SRC_REF_25M		4
 #define YT8531_SCR_CLK_SRC_SSC_25M		5
-#define YT8531S_SYNCE_CFG_REG			0xA012
-#define YT8531S_SCR_SYNCE_ENABLE		BIT(6)
 
 /* Extended Register  end */
 
@@ -858,7 +856,32 @@  static int yt8521_probe(struct phy_device *phydev)
 			return -EINVAL;
 		}
 	} else if (phydev->drv->phy_id == PHY_ID_YT8531S) {
-		return 0;
+		switch (freq) {
+		case YTPHY_DTS_OUTPUT_CLK_DIS:
+			mask = YT8531_SCR_SYNCE_ENABLE;
+			val = 0;
+			break;
+		case YTPHY_DTS_OUTPUT_CLK_25M:
+			mask = YT8531_SCR_SYNCE_ENABLE |
+			       YT8531_SCR_CLK_SRC_MASK |
+			       YT8531_SCR_CLK_FRE_SEL_125M;
+			val = YT8531_SCR_SYNCE_ENABLE |
+			      FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+					 YT8531_SCR_CLK_SRC_REF_25M);
+			break;
+		case YTPHY_DTS_OUTPUT_CLK_125M:
+			mask = YT8531_SCR_SYNCE_ENABLE |
+			       YT8531_SCR_CLK_SRC_MASK |
+			       YT8531_SCR_CLK_FRE_SEL_125M;
+			val = YT8531_SCR_SYNCE_ENABLE |
+			      YT8531_SCR_CLK_FRE_SEL_125M |
+			      FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+					 YT8531_SCR_CLK_SRC_PLL_125M);
+			break;
+		default:
+			phydev_warn(phydev, "Freq err:%u\n", freq);
+			return -EINVAL;
+		}
 	} else {
 		phydev_warn(phydev, "PHY id err\n");
 		return -EINVAL;
@@ -868,26 +891,6 @@  static int yt8521_probe(struct phy_device *phydev)
 					  val);
 }
 
-/**
- * yt8531s_probe() - read chip config then set suitable polling_mode
- * @phydev: a pointer to a &struct phy_device
- *
- * returns 0 or negative errno code
- */
-static int yt8531s_probe(struct phy_device *phydev)
-{
-	int ret;
-
-	/* Disable SyncE clock output by default */
-	ret = ytphy_modify_ext_with_lock(phydev, YT8531S_SYNCE_CFG_REG,
-					 YT8531S_SCR_SYNCE_ENABLE, 0);
-	if (ret < 0)
-		return ret;
-
-	/* same as yt8521_probe */
-	return yt8521_probe(phydev);
-}
-
 /**
  * ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp
  * @phydev: a pointer to a &struct phy_device
@@ -1970,7 +1973,7 @@  static struct phy_driver motorcomm_phy_drvs[] = {
 		PHY_ID_MATCH_EXACT(PHY_ID_YT8531S),
 		.name		= "YT8531S Gigabit Ethernet",
 		.get_features	= yt8521_get_features,
-		.probe		= yt8531s_probe,
+		.probe		= yt8521_probe,
 		.read_page	= yt8521_read_page,
 		.write_page	= yt8521_write_page,
 		.get_wol	= ytphy_get_wol,