@@ -632,6 +632,50 @@ static void ksz8_w_vlan_table(struct ksz_device *dev, u16 vid, u16 vlan)
ksz8_w_table(dev, TABLE_VLAN, addr, buf);
}
+/**
+ * ksz8_r_phy_ctrl - Translates and reads from the SMI interface to a MIIM PHY
+ * Control register (Reg. 31).
+ * @dev: The KSZ device instance.
+ * @port: The port number to be read.
+ * @val: The value read from the SMI interface.
+ *
+ * This function reads the SMI interface and translates the hardware register
+ * bit values into their corresponding control settings for a MIIM PHY Control
+ * register.
+ *
+ * Return: 0 on success, error code on failure.
+ */
+static int ksz8_r_phy_ctrl(struct ksz_device *dev, int port, u16 *val)
+{
+ const u16 *regs = dev->info->regs;
+ u8 reg_val;
+ int ret;
+
+ *val = 0;
+
+ ret = ksz_pread8(dev, port, regs[P_LINK_STATUS], ®_val);
+ if (ret < 0)
+ return ret;
+
+ if (reg_val & PORT_MDIX_STATUS)
+ *val |= KSZ886X_CTRL_MDIX_STAT;
+
+ ret = ksz_pread8(dev, port, REG_PORT_LINK_MD_CTRL, ®_val);
+ if (ret < 0)
+ return ret;
+
+ if (reg_val & PORT_FORCE_LINK)
+ *val |= KSZ886X_CTRL_FORCE_LINK;
+
+ if (reg_val & PORT_POWER_SAVING)
+ *val |= KSZ886X_CTRL_PWRSAVE;
+
+ if (reg_val & PORT_PHY_REMOTE_LOOPBACK)
+ *val |= KSZ886X_CTRL_REMOTE_LOOPBACK;
+
+ return 0;
+}
+
int ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
{
u8 restart, speed, ctrl, link;
@@ -769,12 +813,10 @@ int ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
FIELD_GET(PORT_CABLE_FAULT_COUNTER_L, val2));
break;
case PHY_REG_PHY_CTRL:
- ret = ksz_pread8(dev, p, regs[P_LINK_STATUS], &link);
+ ret = ksz8_r_phy_ctrl(dev, p, &data);
if (ret)
return ret;
- if (link & PORT_MDIX_STATUS)
- data |= KSZ886X_CTRL_MDIX_STAT;
break;
default:
processed = false;
@@ -786,6 +828,38 @@ int ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
return 0;
}
+/**
+ * ksz8_w_phy_ctrl - Translates and writes to the SMI interface from a MIIM PHY
+ * Control register (Reg. 31).
+ * @dev: The KSZ device instance.
+ * @port: The port number to be configured.
+ * @val: The register value to be written.
+ *
+ * This function translates control settings from a MIIM PHY Control register
+ * into their corresponding hardware register bit values for the SMI
+ * interface.
+ *
+ * Return: 0 on success, error code on failure.
+ */
+static int ksz8_w_phy_ctrl(struct ksz_device *dev, int port, u16 val)
+{
+ u8 reg_val = 0;
+ int ret;
+
+ if (val & KSZ886X_CTRL_FORCE_LINK)
+ reg_val |= PORT_FORCE_LINK;
+
+ if (val & KSZ886X_CTRL_PWRSAVE)
+ reg_val |= PORT_POWER_SAVING;
+
+ if (val & KSZ886X_CTRL_REMOTE_LOOPBACK)
+ reg_val |= PORT_PHY_REMOTE_LOOPBACK;
+
+ ret = ksz_prmw8(dev, port, REG_PORT_LINK_MD_CTRL, PORT_FORCE_LINK |
+ PORT_POWER_SAVING | PORT_PHY_REMOTE_LOOPBACK, reg_val);
+ return ret;
+}
+
int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
{
u8 restart, speed, ctrl, data;
@@ -926,6 +1000,12 @@ int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
if (val & PHY_START_CABLE_DIAG)
ksz_port_cfg(dev, p, REG_PORT_LINK_MD_CTRL, PORT_START_CABLE_DIAG, true);
break;
+
+ case PHY_REG_PHY_CTRL:
+ ret = ksz8_w_phy_ctrl(dev, p, val);
+ if (ret)
+ return ret;
+ break;
default:
break;
}
Provide access to MIIM PHY Control register (Reg. 31) through ksz8_r_phy_ctrl() and ksz8_w_phy_ctrl() functions. Necessary for upcoming micrel.c patch to address forced link mode configuration. Closes: https://lore.kernel.org/oe-kbuild-all/202310112224.iYgvjBUy-lkp@intel.com/ Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/net/dsa/microchip/ksz8795.c | 86 ++++++++++++++++++++++++++++- 1 file changed, 83 insertions(+), 3 deletions(-)